From: Andrei-Niculae Petre <p31andrei@gmail.com>
To: dev@dpdk.org
Cc: thomas@monjalon.net, Andrei-Niculae Petre <p31andrei@gmail.com>
Subject: [PATCH v2] examples/l3fwd: sync cli options with documentation
Date: Sun, 15 Nov 2026 23:56:57 +0200 [thread overview]
Message-ID: <20261115215657.14694-1-p31andrei@gmail.com> (raw)
In-Reply-To: <20261109004913.72418-1-p31andrei@gmail.com>
Synchronize options between print_usage() in main.c and the sample app
guide documentation (l3_forward.rst).
Specifically:
- Add missing options to print_usage() synopsis: --eth-link-speed,
--disable-rss, --relax-rx-offload, --event-eth-rxqs, and --alg.
- Add missing option descriptions in print_usage(): --disable-rss and
--relax-rx-offload.
- Clarify in print_usage() that --eth-link-speed unit is in Mbps.
- Add missing options to l3_forward.rst: --eth-link-speed,
--rx-queue-size, --tx-queue-size, --mbcache, --disable-rss,
--relax-rx-offload, and --alg.
- Remove obsolete --hash-entry-num from l3_forward.rst as the option
has been ignored since commit f5251734c5e1 ("examples/l3fwd: remove
hash entry number").
All 25 active long options are now fully documented and aligned across
main.c and l3_forward.rst.
Doing a pass of all the options shows main.c >= 2 and rst >= 2 for each
of them, proving no more omissions exist now.
$ for opt in $(grep -oP '#define CMD_(LINE|LINK)_OPT_\w+\s+"\K[^"]+' \
examples/l3fwd/main.c | grep -v 'hash-entry-num'); do
printf "%-20s: main.c: %2d, rst: %2d\n" "$opt" \
"$(grep -c -- "--$opt" examples/l3fwd/main.c)" \
"$(grep -c -- "--$opt" doc/guides/sample_app_ug/l3_forward.rst)"
done
config : main.c: 2, rst: 5
eth-link-speed : main.c: 2, rst: 2
rx-queue-size : main.c: 2, rst: 2
tx-queue-size : main.c: 2, rst: 2
eth-dest : main.c: 2, rst: 2
no-numa : main.c: 2, rst: 2
ipv6 : main.c: 2, rst: 3
max-pkt-len : main.c: 2, rst: 2
parse-ptype : main.c: 2, rst: 2
disable-rss : main.c: 2, rst: 2
relax-rx-offload : main.c: 2, rst: 2
per-port-pool : main.c: 2, rst: 2
mode : main.c: 4, rst: 8
eventq-sched : main.c: 2, rst: 6
event-eth-rxqs : main.c: 2, rst: 2
lookup : main.c: 4, rst: 4
event-vector : main.c: 4, rst: 4
event-vector-size : main.c: 2, rst: 2
event-vector-tmo : main.c: 2, rst: 2
rule_ipv4 : main.c: 2, rst: 6
rule_ipv6 : main.c: 2, rst: 6
alg : main.c: 2, rst: 2
rx-burst : main.c: 2, rst: 2
tx-burst : main.c: 2, rst: 2
mbcache : main.c: 2, rst: 2
Bugzilla ID: 545
Signed-off-by: Andrei-Niculae Petre <p31andrei@gmail.com>
---
v2:
* Remove 10 and 100 Mbps from --eth-link-speed documentation examples as
they are explicitly rejected by the parser.
* Clarify that --relax-rx-offload masks unsupported offloads to allow
configuration, but does not enable software validation across all
forwarding paths.
* Clarify in print_usage() that --eth-link-speed unit is in Mbps.
---
---
doc/guides/sample_app_ug/l3_forward.rst | 30 ++++++++++++++++++++-----
examples/l3fwd/main.c | 9 +++++++-
2 files changed, 32 insertions(+), 7 deletions(-)
diff --git a/doc/guides/sample_app_ug/l3_forward.rst b/doc/guides/sample_app_ug/l3_forward.rst
index 4e87141608..73f4f4ce41 100644
--- a/doc/guides/sample_app_ug/l3_forward.rst
+++ b/doc/guides/sample_app_ug/l3_forward.rst
@@ -77,19 +77,25 @@ The application has a number of command line options::
[-P]
[--lookup LOOKUP_METHOD]
--config(port,queue,lcore)[,(port,queue,lcore)]
+ [--eth-link-speed SPEED]
+ [--rx-queue-size NPKTS]
+ [--tx-queue-size NPKTS]
[--rx-burst NPKTS]
[--tx-burst NPKTS]
+ [--mbcache CACHESZ]
[--eth-dest=X,MM:MM:MM:MM:MM:MM]
[--max-pkt-len PKTLEN]
[--no-numa]
- [--hash-entry-num]
[--ipv6]
[--parse-ptype]
+ [--disable-rss]
+ [--relax-rx-offload]
[--per-port-pool]
[--mode]
[--eventq-sched]
[--event-eth-rxqs]
[--event-vector [--event-vector-size SIZE] [--event-vector-tmo NS]]
+ [--alg ALG]
[-E]
[-L]
@@ -115,22 +121,37 @@ Where,
* ``--config (port,queue,lcore)[,(port,queue,lcore)]:`` Determines which queues from which ports are mapped to which cores.
+* ``--eth-link-speed SPEED:`` Optional, forces link speed (e.g. 1000, 10000, 25000, 40000, 100000 Mbps).
+
+* ``--rx-queue-size NPKTS:`` Optional, sets the number of Rx descriptors per queue (default 1024).
+
+* ``--tx-queue-size NPKTS:`` Optional, sets the number of Tx descriptors per queue (default 1024).
+
* ``--rx-burst NPKTS:`` Optional, Rx burst size in decimal (default 32).
* ``--tx-burst NPKTS:`` Optional, Tx burst size in decimal (default 32).
+* ``--mbcache CACHESZ:`` Optional, sets the mbuf pool cache size per lcore (default 512).
+
* ``--eth-dest=X,MM:MM:MM:MM:MM:MM:`` Optional, ethernet destination for port X.
* ``--max-pkt-len:`` Optional, maximum packet length in decimal (64-9600).
* ``--no-numa:`` Optional, disables numa awareness.
-* ``--hash-entry-num:`` Optional, specifies the hash entry number in hexadecimal to be setup.
-
* ``--ipv6:`` Optional, set if running ipv6 packets.
* ``--parse-ptype:`` Optional, set to use software to analyze packet type. Without this option, hardware will check the packet type.
+* ``--disable-rss:`` Optional, disables RSS (Receive Side Scaling).
+
+* ``--relax-rx-offload:`` Optional, relaxes Rx offload requirements based on device
+ capabilities. When requested offloads (such as Rx checksum offload) are not supported
+ by the device (e.g., virtual devices such as ``vhost``, ``virtio``, or ``pcap``),
+ unsupported offloads are masked off so the device can be configured
+ successfully, but note that software validation is not enabled on all
+ forwarding paths.
+
* ``--per-port-pool:`` Optional, set to use independent buffer pools per port. Without this option, single buffer pool is used for all ports.
* ``--mode:`` Optional, Packet transfer mode for I/O, poll or eventdev.
@@ -322,9 +343,6 @@ for the convenience to execute hash performance test on 4M/8M/16M flows.
.. note::
Value of global variable ipv6 can be specified with --ipv6 in the command line.
- Value of global variable hash_entry_number,
- which is used to specify the total hash entry number for all used ports in hash performance test,
- can be specified with --hash-entry-num VALUE in command line, being its default value 4.
.. code-block:: c
diff --git a/examples/l3fwd/main.c b/examples/l3fwd/main.c
index 060a68b7aa..5d061a1cf7 100644
--- a/examples/l3fwd/main.c
+++ b/examples/l3fwd/main.c
@@ -397,6 +397,7 @@ print_usage(const char *prgname)
" [-P]"
" [--lookup]"
" --config (port,queue,lcore)[,(port,queue,lcore)]"
+ " [--eth-link-speed SPEED]"
" [--rx-queue-size NPKTS]"
" [--tx-queue-size NPKTS]"
" [--rx-burst NPKTS]"
@@ -407,12 +408,16 @@ print_usage(const char *prgname)
" [--no-numa]"
" [--ipv6]"
" [--parse-ptype]"
+ " [--disable-rss]"
+ " [--relax-rx-offload]"
" [--per-port-pool]"
" [--mode]"
#ifdef RTE_LIB_EVENTDEV
" [--eventq-sched]"
+ " [--event-eth-rxqs]"
" [--event-vector [--event-vector-size SIZE] [--event-vector-tmo NS]]"
#endif
+ " [--alg ALG]"
" [-E]"
" [-L]\n\n"
@@ -423,7 +428,7 @@ print_usage(const char *prgname)
" Accepted: em (Exact Match), lpm (Longest Prefix Match), fib (Forwarding Information Base),\n"
" acl (Access Control List)\n"
" --config (port,queue,lcore): Rx queue configuration\n"
- " --eth-link-speed: force link speed\n"
+ " --eth-link-speed: force link speed (Mbps)\n"
" --rx-queue-size NPKTS: Rx queue size in decimal\n"
" Default: %d\n"
" --tx-queue-size NPKTS: Tx queue size in decimal\n"
@@ -439,6 +444,8 @@ print_usage(const char *prgname)
" --no-numa: Disable numa awareness\n"
" --ipv6: Set if running ipv6 packets\n"
" --parse-ptype: Set to use software to analyze packet type\n"
+ " --disable-rss: Disable RSS\n"
+ " --relax-rx-offload: Relax Rx offload mode\n"
" --per-port-pool: Use separate buffer pool per port\n"
" --mode: Packet transfer mode for I/O, poll or eventdev\n"
" Default mode = poll\n"
--
2.39.5
prev parent reply other threads:[~2026-11-15 21:57 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-09 0:49 [PATCH] examples/l3fwd: sync cli options with documentation Andrei-Niculae Petre
2026-11-12 21:39 ` Thomas Monjalon
2026-11-15 21:56 ` Andrei-Niculae Petre [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261115215657.14694-1-p31andrei@gmail.com \
--to=p31andrei@gmail.com \
--cc=dev@dpdk.org \
--cc=thomas@monjalon.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox