[PATCH 1/5] drm: zte: add interlace mode support

[Shawn Guo <shawnguo@kernel.org>]

From: Shawn Guo <shawn.guo@linaro.org>

It adds interlace mode support in VOU TIMING_CTRL and channel control
block, so that VOU driver gets ready to support output device in
interlace mode like TV Encoder.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
 drivers/gpu/drm/zte/zx_vou.c      | 53 +++++++++++++++++++++++++++++++++++++--
 drivers/gpu/drm/zte/zx_vou_regs.h | 15 +++++++++++
 2 files changed, 66 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/zte/zx_vou.c b/drivers/gpu/drm/zte/zx_vou.c
index 3056b41df518..8c4f0e2885f3 100644
--- a/drivers/gpu/drm/zte/zx_vou.c
+++ b/drivers/gpu/drm/zte/zx_vou.c
@@ -40,6 +40,7 @@ struct zx_crtc_regs {
 	u32 fir_active;
 	u32 fir_htiming;
 	u32 fir_vtiming;
+	u32 sec_vtiming;
 	u32 timing_shift;
 	u32 timing_pi_shift;
 };
@@ -48,6 +49,7 @@ struct zx_crtc_regs {
 	.fir_active = FIR_MAIN_ACTIVE,
 	.fir_htiming = FIR_MAIN_H_TIMING,
 	.fir_vtiming = FIR_MAIN_V_TIMING,
+	.sec_vtiming = SEC_MAIN_V_TIMING,
 	.timing_shift = TIMING_MAIN_SHIFT,
 	.timing_pi_shift = TIMING_MAIN_PI_SHIFT,
 };
@@ -56,6 +58,7 @@ struct zx_crtc_regs {
 	.fir_active = FIR_AUX_ACTIVE,
 	.fir_htiming = FIR_AUX_H_TIMING,
 	.fir_vtiming = FIR_AUX_V_TIMING,
+	.sec_vtiming = SEC_AUX_V_TIMING,
 	.timing_shift = TIMING_AUX_SHIFT,
 	.timing_pi_shift = TIMING_AUX_PI_SHIFT,
 };
@@ -65,6 +68,10 @@ struct zx_crtc_bits {
 	u32 polarity_shift;
 	u32 int_frame_mask;
 	u32 tc_enable;
+	u32 sec_vactive_shift;
+	u32 sec_vactive_mask;
+	u32 interlace_select;
+	u32 pi_enable;
 };
 
 static const struct zx_crtc_bits main_crtc_bits = {
@@ -72,6 +79,10 @@ struct zx_crtc_bits {
 	.polarity_shift = MAIN_POL_SHIFT,
 	.int_frame_mask = TIMING_INT_MAIN_FRAME,
 	.tc_enable = MAIN_TC_EN,
+	.sec_vactive_shift = SEC_VACT_MAIN_SHIFT,
+	.sec_vactive_mask = SEC_VACT_MAIN_MASK,
+	.interlace_select = MAIN_INTERLACE_SEL,
+	.pi_enable = MAIN_PI_EN,
 };
 
 static const struct zx_crtc_bits aux_crtc_bits = {
@@ -79,6 +90,10 @@ struct zx_crtc_bits {
 	.polarity_shift = AUX_POL_SHIFT,
 	.int_frame_mask = TIMING_INT_AUX_FRAME,
 	.tc_enable = AUX_TC_EN,
+	.sec_vactive_shift = SEC_VACT_AUX_SHIFT,
+	.sec_vactive_mask = SEC_VACT_AUX_MASK,
+	.interlace_select = AUX_INTERLACE_SEL,
+	.pi_enable = AUX_PI_EN,
 };
 
 struct zx_crtc {
@@ -196,19 +211,26 @@ static inline void vou_chn_set_update(struct zx_crtc *zcrtc)
 static void zx_crtc_enable(struct drm_crtc *crtc)
 {
 	struct drm_display_mode *mode = &crtc->state->adjusted_mode;
+	bool interlaced = mode->flags & DRM_MODE_FLAG_INTERLACE;
 	struct zx_crtc *zcrtc = to_zx_crtc(crtc);
 	struct zx_vou_hw *vou = zcrtc->vou;
 	const struct zx_crtc_regs *regs = zcrtc->regs;
 	const struct zx_crtc_bits *bits = zcrtc->bits;
 	struct videomode vm;
+	u32 vactive;
 	u32 pol = 0;
 	u32 val;
+	u32 mask;
 	int ret;
 
 	drm_display_mode_to_videomode(mode, &vm);
 
 	/* Set up timing parameters */
-	val = V_ACTIVE(vm.vactive - 1);
+	vactive = vm.vactive;
+	if (interlaced)
+		vactive /= 2;
+
+	val = V_ACTIVE(vactive - 1);
 	val |= H_ACTIVE(vm.hactive - 1);
 	zx_writel(vou->timing + regs->fir_active, val);
 
@@ -222,6 +244,22 @@ static void zx_crtc_enable(struct drm_crtc *crtc)
 	val |= FRONT_PORCH(vm.vfront_porch - 1);
 	zx_writel(vou->timing + regs->fir_vtiming, val);
 
+	if (interlaced) {
+		u32 shift = bits->sec_vactive_shift;
+		u32 mask = bits->sec_vactive_mask;
+
+		val = zx_readl(vou->timing + SEC_V_ACTIVE);
+		val &= ~mask;
+		val |= ((vactive - 1) << shift) & mask;
+		zx_writel(vou->timing + SEC_V_ACTIVE, val);
+
+		val = SYNC_WIDE(vm.vsync_len - 1);
+		/* sec_vbp = fir_vbp + 1 */
+		val |= BACK_PORCH(vm.vback_porch);
+		val |= FRONT_PORCH(vm.vfront_porch - 1);
+		zx_writel(vou->timing + regs->sec_vtiming, val);
+	}
+
 	/* Set up polarities */
 	if (vm.flags & DISPLAY_FLAGS_VSYNC_LOW)
 		pol |= 1 << POL_VSYNC_SHIFT;
@@ -232,9 +270,16 @@ static void zx_crtc_enable(struct drm_crtc *crtc)
 		       pol << bits->polarity_shift);
 
 	/* Setup SHIFT register by following what ZTE BSP does */
-	zx_writel(vou->timing + regs->timing_shift, H_SHIFT_VAL);
+	val = H_SHIFT_VAL;
+	if (interlaced)
+		val |= V_SHIFT_VAL << 16;
+	zx_writel(vou->timing + regs->timing_shift, val);
 	zx_writel(vou->timing + regs->timing_pi_shift, H_PI_SHIFT_VAL);
 
+	/* Progressive or interlace scan select */
+	mask = bits->interlace_select | bits->pi_enable;
+	zx_writel_mask(vou->timing + SCAN_CTRL, mask, interlaced ? mask : 0);
+
 	/* Enable TIMING_CTRL */
 	zx_writel_mask(vou->timing + TIMING_TC_ENABLE, bits->tc_enable,
 		       bits->tc_enable);
@@ -245,6 +290,10 @@ static void zx_crtc_enable(struct drm_crtc *crtc)
 	zx_writel_mask(zcrtc->chnreg + CHN_CTRL1, CHN_SCREEN_H_MASK,
 		       vm.vactive << CHN_SCREEN_H_SHIFT);
 
+	/* Configure channel interlace buffer control */
+	zx_writel_mask(zcrtc->chnreg + CHN_INTERLACE_BUF_CTRL, CHN_INTERLACE_EN,
+		       interlaced ? CHN_INTERLACE_EN : 0);
+
 	/* Update channel */
 	vou_chn_set_update(zcrtc);
 
diff --git a/drivers/gpu/drm/zte/zx_vou_regs.h b/drivers/gpu/drm/zte/zx_vou_regs.h
index 193c1ce01fe7..e6ed844e068a 100644
--- a/drivers/gpu/drm/zte/zx_vou_regs.h
+++ b/drivers/gpu/drm/zte/zx_vou_regs.h
@@ -75,6 +75,8 @@
 #define CHN_SCREEN_H_SHIFT		5
 #define CHN_SCREEN_H_MASK		(0x1fff << CHN_SCREEN_H_SHIFT)
 #define CHN_UPDATE			0x08
+#define CHN_INTERLACE_BUF_CTRL		0x24
+#define CHN_INTERLACE_EN		BIT(2)
 
 /* TIMING_CTRL registers */
 #define TIMING_TC_ENABLE		0x04
@@ -117,6 +119,19 @@
 #define TIMING_MAIN_SHIFT		0x2c
 #define TIMING_AUX_SHIFT		0x30
 #define H_SHIFT_VAL			0x0048
+#define V_SHIFT_VAL			0x0001
+#define SCAN_CTRL			0x34
+#define AUX_PI_EN			BIT(19)
+#define MAIN_PI_EN			BIT(18)
+#define AUX_INTERLACE_SEL		BIT(1)
+#define MAIN_INTERLACE_SEL		BIT(0)
+#define SEC_V_ACTIVE			0x38
+#define SEC_VACT_MAIN_SHIFT		0
+#define SEC_VACT_MAIN_MASK		(0xffff << SEC_VACT_MAIN_SHIFT)
+#define SEC_VACT_AUX_SHIFT		16
+#define SEC_VACT_AUX_MASK		(0xffff << SEC_VACT_AUX_SHIFT)
+#define SEC_MAIN_V_TIMING		0x3c
+#define SEC_AUX_V_TIMING		0x40
 #define TIMING_MAIN_PI_SHIFT		0x68
 #define TIMING_AUX_PI_SHIFT		0x6c
 #define H_PI_SHIFT_VAL			0x000f
-- 
1.9.1

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel