Re: [PATCH 20/20] drm/i915: write AVI infoframes for LSPCON

["Ville Syrjälä" <ville.syrjala@linux.intel.com>]

On Mon, Jul 10, 2017 at 04:48:48PM +0530, Shashank Sharma wrote:
> LSPCON chips can't pick the HDMI AVI infoframes from direct link.
> In order to pass AVI infoframes from display controller to LSPCON,
> we have to write infoframe packets into vendor specified AUX address.
> 
> Also, LSPCON vendors provide AUX offsets, to inform the LSPCON
> chip that the AVI IF packets are written, so that the firmware
> can pick it up and apply.
> 
> This patch adds function to write AVI infoframes for both MCA as
> well as Parade Tech LSPCON chips. These two vendors provide different
> methods for writing infoframes, so this patch contains two different
> functions, one for each.

Seems to me that we should also be checking the receiver cap for the
444->420 conversion support, and enable it in the PROTOCOL_CONVERTER
DPCD register. Or are these LSPCON things even ignoring that part of the
spec?

> 
> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
> Cc: Imre Deak <imre.deak@intel.com>
> Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
> ---
>  drivers/gpu/drm/i915/intel_ddi.c    |   8 ++
>  drivers/gpu/drm/i915/intel_drv.h    |   3 +
>  drivers/gpu/drm/i915/intel_lspcon.c | 174 ++++++++++++++++++++++++++++++++++++
>  3 files changed, 185 insertions(+)
> 
> diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
> index f691710..944d9d5 100644
> --- a/drivers/gpu/drm/i915/intel_ddi.c
> +++ b/drivers/gpu/drm/i915/intel_ddi.c
> @@ -2068,6 +2068,14 @@ void intel_ddi_set_avi_infoframe(struct drm_encoder *encoder,
>  					   rgb_qrange_limited,
>  					   rgb_qrange_selectable);
>  
> +	if (crtc_state->lspcon_active) {
> +		struct intel_lspcon *lspcon = enc_to_intel_lspcon(encoder);
> +
> +		/* LSPCON writes infoframes via AUX */
> +		lspcon->write_infoframe(encoder, crtc_state, &frame);
> +		return;
> +	}
> +
>  	intel_write_infoframe(encoder, crtc_state, &frame);
>  }
>  
> diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
> index fad9a53..3e686d2 100644
> --- a/drivers/gpu/drm/i915/intel_drv.h
> +++ b/drivers/gpu/drm/i915/intel_drv.h
> @@ -1079,6 +1079,9 @@ struct intel_lspcon {
>  	/* AVI IF setup function for LSPCON */
>  	void (*set_infoframes)(struct drm_encoder *encoder,
>  				const struct intel_crtc_state *crtc_state);
> +	void (*write_infoframe)(struct drm_encoder *encoder,
> +				const struct intel_crtc_state *crtc_state,
> +				union hdmi_infoframe *frame);
>  };
>  
>  struct intel_digital_port {
> diff --git a/drivers/gpu/drm/i915/intel_lspcon.c b/drivers/gpu/drm/i915/intel_lspcon.c
> index 53ddd39..01fddf7 100644
> --- a/drivers/gpu/drm/i915/intel_lspcon.c
> +++ b/drivers/gpu/drm/i915/intel_lspcon.c
> @@ -31,6 +31,18 @@
>  #define LSPCON_VENDOR_PARADE_OUI 0x001CF8
>  #define LSPCON_VENDOR_MCA_OUI 0x0060AD
>  
> +/* AUX addresses to write AVI IF into */
> +#define LSPCON_MCA_AVI_IF_WRITE_OFFSET 0x5C0
> +#define LSPCON_MCA_AVI_IF_CTRL 0x5DF
> +#define  LSPCON_MCA_AVI_IF_KICKOFF (1 << 0)
> +#define  LSPCON_MCA_AVI_IF_HANDLED (1 << 1)
> +
> +#define LSPCON_PARADE_AVI_IF_WRITE_OFFSET 0x516
> +#define LSPCON_PARADE_AVI_IF_CTRL 0x51E
> +#define  LSPCON_PARADE_AVI_IF_KICKOFF (1 << 7)
> +#define LSPCON_PARADE_AVI_IF_STATUS 0x51F
> +#define  LSPCON_PARADE_AVI_IF_HANDLED (2 << 6)
> +
>  static struct intel_dp *lspcon_to_intel_dp(struct intel_lspcon *lspcon)
>  {
>  	struct intel_digital_port *dig_port =
> @@ -217,6 +229,167 @@ bool lspcon_ycbcr420_config(struct drm_connector *connector,
>  	return false;
>  }
>  
> +static bool _lspcon_write_infoframe_parade(struct drm_dp_aux *aux,
> +					   uint8_t *buffer, ssize_t len)
> +{
> +	u8 avi_if_ctrl;
> +	u8 avi_if_status;
> +	u8 count = 0;
> +	u8 retry = 5;
> +	u8 avi_buf[8] = {0, };
> +	uint16_t reg;
> +	ssize_t ret;
> +
> +	while (count++ < 4) {
> +
> +		do {
> +			/* Is LSPCON FW ready */
> +			reg = LSPCON_PARADE_AVI_IF_CTRL;
> +			ret = drm_dp_dpcd_read(aux, reg, &avi_if_ctrl, 1);
> +			if (ret < 0) {
> +				DRM_ERROR("DPCD read failed, add:0x%x\n", reg);
> +				return false;
> +			}
> +
> +			if (avi_if_ctrl & LSPCON_PARADE_AVI_IF_KICKOFF)
> +				break;
> +			usleep_range(100, 200);
> +		} while (--retry);
> +
> +		if (!(avi_if_ctrl & LSPCON_PARADE_AVI_IF_KICKOFF)) {
> +			DRM_ERROR("LSPCON FW not ready for infoframes\n");
> +			return false;
> +		}
> +
> +		/*
> +		 * AVI Infoframe contains 31 bytes of data:
> +		 *	HB0 to HB2   (3 bytes header)
> +		 *	PB0 to PB27 (28 bytes data)
> +		 * As per Parade spec, while sending first block (8bytes),
> +		 * byte 0 is kept for request token no, and byte1 - byte7
> +		 * contain frame data. So we have to pack frame like this:
> +		 *	first block of 8 bytes: <token> <HB0-HB2> <PB0-PB3>
> +		 *	next 3 blocks: <PB4-PB27>
> +		 */
> +		if (count)
> +			memcpy(avi_buf, buffer + count * 8 - 1, 8);
> +		else {
> +			avi_buf[0] = 1;
> +			memcpy(&avi_buf[1], buffer, 7);
> +		}
> +
> +		/* Write 8 bytes of data at a time */
> +		reg = LSPCON_PARADE_AVI_IF_WRITE_OFFSET;
> +		ret = drm_dp_dpcd_write(aux, reg, avi_buf, 8);
> +		if (ret < 0) {
> +			DRM_ERROR("DPCD write failed, add:0x%x\n", reg);
> +			return false;
> +		}
> +
> +		/*
> +		 * While sending a block of 8 byes, we need to inform block
> +		 * number to FW, by programming bits[1:0] of ctrl reg with
> +		 * block number
> +		 */
> +		avi_if_ctrl = 0x80 + count;
> +		reg = LSPCON_PARADE_AVI_IF_CTRL;
> +		ret = drm_dp_dpcd_write(aux, reg, &avi_if_ctrl, 1);
> +		if (ret < 0) {
> +			DRM_ERROR("DPCD write failed, add:0x%x\n", reg);
> +			return false;
> +		}
> +	}
> +
> +	/* Check LSPCON FW status */
> +	reg = LSPCON_PARADE_AVI_IF_STATUS;
> +	ret = drm_dp_dpcd_read(aux, reg, &avi_if_status, 1);
> +	if (ret < 0) {
> +		DRM_ERROR("DPCD write failed, address 0x%x\n", reg);
> +		return false;
> +	}
> +
> +	if (avi_if_status & LSPCON_PARADE_AVI_IF_HANDLED)
> +		DRM_DEBUG_KMS("AVI IF handled by FW\n");
> +
> +	return true;
> +}
> +
> +static bool _lspcon_write_infoframe_mca(struct drm_dp_aux *aux,
> +					uint8_t *buffer, ssize_t len)
> +{
> +	int ret;
> +	uint32_t val = 0;
> +	uint16_t reg;
> +	uint8_t *data = buffer;
> +
> +	reg = LSPCON_MCA_AVI_IF_WRITE_OFFSET;
> +	while (val < len) {
> +		ret = drm_dp_dpcd_write(aux, reg, data, 1);
> +		if (ret < 0) {
> +			DRM_ERROR("DPCD write failed, add:0x%x\n", reg);
> +			return false;
> +		}
> +		val++; reg++; data++;
> +	}
> +
> +	val = 0;
> +	reg = LSPCON_MCA_AVI_IF_CTRL;
> +	ret = drm_dp_dpcd_read(aux, reg, &val, 1);
> +	if (ret < 0) {
> +		DRM_ERROR("DPCD read failed, address 0x%x\n", reg);
> +		return false;
> +	}
> +
> +	/* Indicate LSPCON chip about infoframe, clear bit 1 and set bit 0 */
> +	val &= ~LSPCON_MCA_AVI_IF_HANDLED;
> +	val |= LSPCON_MCA_AVI_IF_KICKOFF;
> +
> +	ret = drm_dp_dpcd_write(aux, reg, &val, 1);
> +	if (ret < 0) {
> +		DRM_ERROR("DPCD read failed, address 0x%x\n", reg);
> +		return false;
> +	}
> +
> +	val = 0;
> +	ret = drm_dp_dpcd_read(aux, reg, &val, 1);
> +	if (ret < 0) {
> +		DRM_ERROR("DPCD read failed, address 0x%x\n", reg);
> +		return false;
> +	}
> +
> +	if (val == LSPCON_MCA_AVI_IF_HANDLED)
> +		DRM_DEBUG_KMS("AVI IF handled by FW\n");
> +
> +	return true;
> +}
> +
> +void lspcon_write_infoframe(struct drm_encoder *encoder,
> +				  const struct intel_crtc_state *crtc_state,
> +				  union hdmi_infoframe *frame)
> +{
> +	bool ret;
> +	ssize_t len;
> +	uint8_t buf[VIDEO_DIP_DATA_SIZE];
> +	struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
> +	struct intel_lspcon *lspcon = enc_to_intel_lspcon(encoder);
> +
> +	len = hdmi_infoframe_pack(frame, buf, sizeof(buf));
> +	if (len < 0) {
> +		DRM_ERROR("Failed to pack AVI IF\n");
> +		return;
> +	}
> +
> +	if (lspcon->vendor == LSPCON_VENDOR_MCA)
> +		ret = _lspcon_write_infoframe_mca(&intel_dp->aux, buf, len);
> +	else
> +		ret = _lspcon_write_infoframe_parade(&intel_dp->aux, buf, len);
> +
> +	if (!ret)
> +		DRM_ERROR("Failed to write AVI infoframes\n");
> +	else
> +		DRM_DEBUG_DRIVER("AVI infoframes updated successfully\n");
> +}
> +
>  void lspcon_resume(struct intel_lspcon *lspcon)
>  {
>  	enum drm_lspcon_mode expected_mode;
> @@ -282,6 +455,7 @@ bool lspcon_init(struct intel_digital_port *intel_dig_port)
>  
>  	connector->ycbcr_420_allowed = true;
>  	lspcon->set_infoframes = intel_ddi_set_avi_infoframe;
> +	lspcon->write_infoframe = lspcon_write_infoframe;
>  	drm_dp_read_desc(&dp->aux, &dp->desc, drm_dp_is_branch(dp->dpcd));
>  
>  	DRM_DEBUG_KMS("Success: LSPCON init\n");
> -- 
> 2.7.4

-- 
Ville Syrjälä
Intel OTC
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx