dri-devel Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: Sam Ravnborg <sam@ravnborg.org>
To: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>,
	Thomas Petazzoni <thomas.petazzoni@bootlin.com>,
	Boris Brezillon <bbrezillon@kernel.org>,
	Nicolas Ferre <nicolas.ferre@microchip.com>,
	dri-devel@lists.freedesktop.org,
	Claudiu Beznea <claudiu.beznea@microchip.com>,
	linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH] drm: atmel-hlcdc: Support inverting the pixel clock polarity
Date: Sat, 10 Jun 2023 22:05:15 +0200	[thread overview]
Message-ID: <20230610200515.GA1041001@ravnborg.org> (raw)
In-Reply-To: <20230609144843.851327-1-miquel.raynal@bootlin.com>

On Fri, Jun 09, 2023 at 04:48:43PM +0200, Miquel Raynal wrote:
> On the SoC host controller, the pixel clock can be:
> * standard: data is launched on the rising edge
> * inverted: data is launched on the falling edge
> 
> Some panels may need the inverted option to be used so let's support
> this DRM flag.
> 
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

Hi Miquel,

the patch is:
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>

I hope someone else can pick it up and apply it to drm-misc as
my drm-misc setup is hopelessly outdated atm.

	Sam


> ---
> 
> Hello, this change was tested on a Sama5d36 based custom board with a
> panel not behaving correctly if the pixel clock was not inverted.
> Cheers, Miquèl
> 
>  .../gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c    | 25 +++++++++++++++++++
>  1 file changed, 25 insertions(+)
> 
> diff --git a/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c b/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c
> index 58184cd6ab0b..cc5cf4c2faf7 100644
> --- a/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c
> +++ b/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c
> @@ -68,7 +68,11 @@ static void atmel_hlcdc_crtc_mode_set_nofb(struct drm_crtc *c)
>  	struct atmel_hlcdc_crtc *crtc = drm_crtc_to_atmel_hlcdc_crtc(c);
>  	struct regmap *regmap = crtc->dc->hlcdc->regmap;
>  	struct drm_display_mode *adj = &c->state->adjusted_mode;
> +	struct drm_encoder *encoder = NULL, *en_iter;
> +	struct drm_connector *connector = NULL;
>  	struct atmel_hlcdc_crtc_state *state;
> +	struct drm_device *ddev = c->dev;
> +	struct drm_connector_list_iter iter;
>  	unsigned long mode_rate;
>  	struct videomode vm;
>  	unsigned long prate;
> @@ -76,6 +80,23 @@ static void atmel_hlcdc_crtc_mode_set_nofb(struct drm_crtc *c)
>  	unsigned int cfg = 0;
>  	int div, ret;
>  
> +	/* get encoder from crtc */
> +	drm_for_each_encoder(en_iter, ddev) {
> +		if (en_iter->crtc == c) {
> +			encoder = en_iter;
> +			break;
> +		}
> +	}
> +
> +	if (encoder) {
> +		/* Get the connector from encoder */
> +		drm_connector_list_iter_begin(ddev, &iter);
> +		drm_for_each_connector_iter(connector, &iter)
> +			if (connector->encoder == encoder)
> +				break;
> +		drm_connector_list_iter_end(&iter);
> +	}
> +
>  	ret = clk_prepare_enable(crtc->dc->hlcdc->sys_clk);
>  	if (ret)
>  		return;
> @@ -134,6 +155,10 @@ static void atmel_hlcdc_crtc_mode_set_nofb(struct drm_crtc *c)
>  
>  	cfg |= ATMEL_HLCDC_CLKDIV(div);
>  
> +	if (connector &&
> +	    connector->display_info.bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE)
> +		cfg |= ATMEL_HLCDC_CLKPOL;
> +
>  	regmap_update_bits(regmap, ATMEL_HLCDC_CFG(0), mask, cfg);
>  
>  	state = drm_crtc_state_to_atmel_hlcdc_crtc_state(c->state);
> -- 
> 2.34.1

  reply	other threads:[~2023-06-10 20:05 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-06-09 14:48 [PATCH] drm: atmel-hlcdc: Support inverting the pixel clock polarity Miquel Raynal
2023-06-10 20:05 ` Sam Ravnborg [this message]
2023-07-12 15:57   ` Miquel Raynal
2023-08-07  9:12   ` Miquel Raynal
2023-08-07 16:52     ` Sam Ravnborg
2023-08-08  6:33       ` Miquel Raynal
2023-08-10  6:45         ` Boris Brezillon
2023-08-10 17:31           ` Sam Ravnborg
2023-08-11  5:53             ` Miquel Raynal

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230610200515.GA1041001@ravnborg.org \
    --to=sam@ravnborg.org \
    --cc=alexandre.belloni@bootlin.com \
    --cc=bbrezillon@kernel.org \
    --cc=claudiu.beznea@microchip.com \
    --cc=dri-devel@lists.freedesktop.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=miquel.raynal@bootlin.com \
    --cc=nicolas.ferre@microchip.com \
    --cc=thomas.petazzoni@bootlin.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox