From: Dharma Balasubiramani <dharma.b@microchip.com>
To: <andrzej.hajda@intel.com>, <neil.armstrong@linaro.org>,
<rfoss@kernel.org>, <Laurent.pinchart@ideasonboard.com>,
<jonas@kwiboo.se>, <jernej.skrabec@gmail.com>,
<maarten.lankhorst@linux.intel.com>, <mripard@kernel.org>,
<tzimmermann@suse.de>, <airlied@gmail.com>, <daniel@ffwll.ch>,
<robh+dt@kernel.org>, <krzysztof.kozlowski+dt@linaro.org>,
<conor+dt@kernel.org>, <dharma.b@microchip.com>,
<dri-devel@lists.freedesktop.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>, <linux@armlinux.org.uk>,
<nicolas.ferre@microchip.com>, <alexandre.belloni@bootlin.com>,
<claudiu.beznea@tuxon.dev>, <geert+renesas@glider.be>,
<arnd@arndb.de>, <hari.prasathge@microchip.com>,
<Jason@zx2c4.com>, <rientjes@google.com>, <rdunlap@infradead.org>,
<vbabka@suse.cz>, <manikandan.m@microchip.com>
Subject: [linux][PATCH v2 2/4] drm/bridge: add lvds controller support for sam9x7
Date: Mon, 5 Feb 2024 16:36:07 +0530 [thread overview]
Message-ID: <20240205110609.217022-3-dharma.b@microchip.com> (raw)
In-Reply-To: <20240205110609.217022-1-dharma.b@microchip.com>
Add a new LVDS controller driver for sam9x7 which does the following:
- Prepares and enables the LVDS Peripheral clock
- Defines its connector type as DRM_MODE_CONNECTOR_LVDS and adds itself
to the global bridge list.
- Identifies its output endpoint as panel and adds it to the encoder
display pipeline
- Enables the LVDS serializer
Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Signed-off-by: Dharma Balasubiramani <dharma.b@microchip.com>
---
Changelog
v1 -> v2
- Drop 'res' variable and combine two lines into one.
- Handle deferred probe properly, use dev_err_probe().
- Don't print anything on deferred probe. Dropped print.
- Remove the MODULE_ALIAS and add MODULE_DEVICE_TABLE().
- symbol 'mchp_lvds_driver' was not declared. It should be static.
---
drivers/gpu/drm/bridge/Kconfig | 7 +
drivers/gpu/drm/bridge/Makefile | 1 +
drivers/gpu/drm/bridge/microchip-lvds.c | 246 ++++++++++++++++++++++++
3 files changed, 254 insertions(+)
create mode 100644 drivers/gpu/drm/bridge/microchip-lvds.c
diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
index 3e6a4e2044c0..200afb36e421 100644
--- a/drivers/gpu/drm/bridge/Kconfig
+++ b/drivers/gpu/drm/bridge/Kconfig
@@ -173,6 +173,13 @@ config DRM_MEGACHIPS_STDPXXXX_GE_B850V3_FW
to DP++. This is used with the i.MX6 imx-ldb
driver. You are likely to say N here.
+config DRM_MICROCHIP_LVDS_SERIALIZER
+ tristate "Microchip LVDS serailzer support"
+ depends on OF
+ depends on DRM_ATMEL_HLCDC
+ help
+ Support for Microchip's LVDS serializer.
+
config DRM_NWL_MIPI_DSI
tristate "Northwest Logic MIPI DSI Host controller"
depends on DRM
diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
index 2b892b7ed59e..e3804e93d324 100644
--- a/drivers/gpu/drm/bridge/Makefile
+++ b/drivers/gpu/drm/bridge/Makefile
@@ -11,6 +11,7 @@ obj-$(CONFIG_DRM_LONTIUM_LT9611) += lontium-lt9611.o
obj-$(CONFIG_DRM_LONTIUM_LT9611UXC) += lontium-lt9611uxc.o
obj-$(CONFIG_DRM_LVDS_CODEC) += lvds-codec.o
obj-$(CONFIG_DRM_MEGACHIPS_STDPXXXX_GE_B850V3_FW) += megachips-stdpxxxx-ge-b850v3-fw.o
+obj-$(CONFIG_DRM_MICROCHIP_LVDS_SERIALIZER) += microchip-lvds.o
obj-$(CONFIG_DRM_NXP_PTN3460) += nxp-ptn3460.o
obj-$(CONFIG_DRM_PARADE_PS8622) += parade-ps8622.o
obj-$(CONFIG_DRM_PARADE_PS8640) += parade-ps8640.o
diff --git a/drivers/gpu/drm/bridge/microchip-lvds.c b/drivers/gpu/drm/bridge/microchip-lvds.c
new file mode 100644
index 000000000000..508321ad0f66
--- /dev/null
+++ b/drivers/gpu/drm/bridge/microchip-lvds.c
@@ -0,0 +1,246 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2023 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Manikandan Muralidharan <manikandan.m@microchip.com>
+ * Author: Dharma Balasubiramani <dharma.b@microchip.com>
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/component.h>
+#include <linux/delay.h>
+#include <linux/jiffies.h>
+#include <linux/mfd/syscon.h>
+#include <linux/of_graph.h>
+#include <linux/pinctrl/devinfo.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_bridge.h>
+#include <drm/drm_of.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_print.h>
+#include <drm/drm_probe_helper.h>
+#include <drm/drm_simple_kms_helper.h>
+
+#define LVDS_POLL_TIMEOUT_MS 1000
+
+/* LVDSC register offsets */
+#define LVDSC_CR 0x00
+#define LVDSC_CFGR 0x04
+#define LVDSC_SR 0x0C
+#define LVDSC_WPMR 0xE4
+
+/* Bitfields in LVDSC_CR (Control Register) */
+#define LVDSC_CR_SER_EN BIT(0)
+
+/* Bitfields in LVDSC_CFGR (Configuration Register) */
+#define LVDSC_CFGR_PIXSIZE_24BITS 0
+#define LVDSC_CFGR_DEN_POL_HIGH 0
+#define LVDSC_CFGR_DC_UNBALANCED 0
+#define LVDSC_CFGR_MAPPING_JEIDA BIT(6)
+
+/*Bitfields in LVDSC_SR */
+#define LVDSC_SR_CS BIT(0)
+
+/* Bitfields in LVDSC_WPMR (Write Protection Mode Register) */
+#define LVDSC_WPMR_WPKEY_MASK GENMASK(31, 8)
+#define LVDSC_WPMR_WPKEY_PSSWD 0x4C5644
+
+struct mchp_lvds {
+ struct device *dev;
+ void __iomem *regs;
+ struct clk *pclk;
+ int format; /* vesa or jeida format */
+ struct drm_panel *panel;
+ struct drm_bridge bridge;
+ struct drm_bridge *panel_bridge;
+};
+
+static inline struct mchp_lvds *bridge_to_lvds(struct drm_bridge *bridge)
+{
+ return container_of(bridge, struct mchp_lvds, bridge);
+}
+
+static inline u32 lvds_readl(struct mchp_lvds *lvds, u32 offset)
+{
+ return readl_relaxed(lvds->regs + offset);
+}
+
+static inline void lvds_writel(struct mchp_lvds *lvds, u32 offset, u32 val)
+{
+ writel_relaxed(val, lvds->regs + offset);
+}
+
+static void lvds_serialiser_on(struct mchp_lvds *lvds)
+{
+ unsigned long timeout = jiffies + msecs_to_jiffies(LVDS_POLL_TIMEOUT_MS);
+
+ /* The LVDSC registers can only be written if WPEN is cleared */
+ lvds_writel(lvds, LVDSC_WPMR, (LVDSC_WPMR_WPKEY_PSSWD &
+ LVDSC_WPMR_WPKEY_MASK));
+
+ /* Wait for the status of configuration registers to be changed */
+ while (lvds_readl(lvds, LVDSC_SR) & LVDSC_SR_CS) {
+ if (time_after(jiffies, timeout)) {
+ dev_err(lvds->dev, "%s: timeout error\n", __func__);
+ return;
+ }
+ usleep_range(1000, 2000);
+ }
+
+ /* Configure the LVDSC */
+ lvds_writel(lvds, LVDSC_CFGR, (LVDSC_CFGR_MAPPING_JEIDA |
+ LVDSC_CFGR_DC_UNBALANCED |
+ LVDSC_CFGR_DEN_POL_HIGH |
+ LVDSC_CFGR_PIXSIZE_24BITS));
+
+ /* Enable the LVDS serializer */
+ lvds_writel(lvds, LVDSC_CR, LVDSC_CR_SER_EN);
+}
+
+static int mchp_lvds_attach(struct drm_bridge *bridge,
+ enum drm_bridge_attach_flags flags)
+{
+ struct mchp_lvds *lvds = bridge_to_lvds(bridge);
+
+ bridge->encoder->encoder_type = DRM_MODE_ENCODER_LVDS;
+
+ return drm_bridge_attach(bridge->encoder, lvds->panel_bridge,
+ bridge, flags);
+}
+
+static void mchp_lvds_enable(struct drm_bridge *bridge)
+{
+ struct mchp_lvds *lvds = bridge_to_lvds(bridge);
+ int ret;
+
+ ret = clk_enable(lvds->pclk);
+ if (ret < 0) {
+ DRM_DEV_ERROR(lvds->dev, "failed to enable lvds pclk %d\n", ret);
+ return;
+ }
+
+ ret = pm_runtime_get_sync(lvds->dev);
+ if (ret < 0) {
+ DRM_DEV_ERROR(lvds->dev, "failed to get pm runtime: %d\n", ret);
+ clk_disable(lvds->pclk);
+ return;
+ }
+
+ lvds_serialiser_on(lvds);
+}
+
+static void mchp_lvds_disable(struct drm_bridge *bridge)
+{
+ struct mchp_lvds *lvds = bridge_to_lvds(bridge);
+
+ pm_runtime_put(lvds->dev);
+ clk_disable(lvds->pclk);
+}
+
+static const struct drm_bridge_funcs mchp_lvds_bridge_funcs = {
+ .attach = mchp_lvds_attach,
+ .enable = mchp_lvds_enable,
+ .disable = mchp_lvds_disable,
+};
+
+static int mchp_lvds_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct mchp_lvds *lvds;
+ struct device_node *port;
+ int ret;
+
+ if (!dev->of_node)
+ return -ENODEV;
+
+ lvds = devm_kzalloc(&pdev->dev, sizeof(*lvds), GFP_KERNEL);
+ if (!lvds)
+ return -ENOMEM;
+
+ lvds->dev = dev;
+
+ lvds->regs = devm_ioremap_resource(lvds->dev,
+ platform_get_resource(pdev, IORESOURCE_MEM, 0));
+ if (IS_ERR(lvds->regs))
+ return PTR_ERR(lvds->regs);
+
+ lvds->pclk = devm_clk_get(lvds->dev, "pclk");
+ if (IS_ERR(lvds->pclk))
+ return dev_err_probe(lvds->dev, PTR_ERR(lvds->pclk),
+ "could not get pclk_lvds\n");
+
+ ret = clk_prepare(lvds->pclk);
+ if (ret < 0) {
+ DRM_DEV_ERROR(lvds->dev, "failed to prepare pclk_lvds\n");
+ return ret;
+ }
+
+ port = of_graph_get_remote_node(dev->of_node, 1, 0);
+ if (!port) {
+ DRM_DEV_ERROR(dev,
+ "can't find port point, please init lvds panel port!\n");
+ return -EINVAL;
+ }
+
+ lvds->panel = of_drm_find_panel(port);
+ of_node_put(port);
+
+ if (IS_ERR(lvds->panel))
+ return -EPROBE_DEFER;
+
+ lvds->panel_bridge = devm_drm_panel_bridge_add(dev, lvds->panel);
+
+ if (IS_ERR(lvds->panel_bridge))
+ return PTR_ERR(lvds->panel_bridge);
+
+ lvds->bridge.of_node = dev->of_node;
+ lvds->bridge.type = DRM_MODE_CONNECTOR_LVDS;
+ lvds->bridge.funcs = &mchp_lvds_bridge_funcs;
+
+ dev_set_drvdata(dev, lvds);
+ pm_runtime_enable(dev);
+
+ drm_bridge_add(&lvds->bridge);
+
+ return 0;
+}
+
+static int mchp_lvds_remove(struct platform_device *pdev)
+{
+ struct mchp_lvds *lvds = platform_get_drvdata(pdev);
+
+ pm_runtime_disable(&pdev->dev);
+ clk_unprepare(lvds->pclk);
+
+ return 0;
+}
+
+static const struct of_device_id mchp_lvds_dt_ids[] = {
+ {
+ .compatible = "microchip,sam9x75-lvds",
+ },
+ {},
+};
+MODULE_DEVICE_TABLE(of, mchp_lvds_dt_ids);
+
+static struct platform_driver mchp_lvds_driver = {
+ .probe = mchp_lvds_probe,
+ .remove = mchp_lvds_remove,
+ .driver = {
+ .name = "microchip-lvds",
+ .of_match_table = mchp_lvds_dt_ids,
+ },
+};
+module_platform_driver(mchp_lvds_driver);
+
+MODULE_AUTHOR("Manikandan Muralidharan <manikandan.m@microchip.com>");
+MODULE_AUTHOR("Dharma Balasubiramani <dharma.b@microchip.com>");
+MODULE_DESCRIPTION("Low Voltage Differential Signaling Controller Driver");
+MODULE_LICENSE("GPL");
--
2.25.1
next prev parent reply other threads:[~2024-02-05 11:07 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-02-05 11:06 [linux][PATCH v2 0/4] LVDS Controller Support for SAM9X75 SoC Dharma Balasubiramani
2024-02-05 11:06 ` [linux][PATCH v2 1/4] dt-bindings: display: bridge: add sam9x75-lvds compatible Dharma Balasubiramani
2024-02-05 20:08 ` Rob Herring
2024-02-05 11:06 ` Dharma Balasubiramani [this message]
2024-02-05 11:11 ` [linux][PATCH v2 2/4] drm/bridge: add lvds controller support for sam9x7 neil.armstrong
2024-02-07 6:45 ` Dharma.B
2024-02-05 11:06 ` [linux][PATCH v2 3/4] MAINTAINERS: add SAM9X7 SoC's LVDS controller Dharma Balasubiramani
2024-02-05 11:11 ` neil.armstrong
2024-02-05 12:55 ` Nicolas Ferre
2024-02-05 11:06 ` [linux][PATCH v2 4/4] ARM: configs: at91: Enable LVDS serializer support Dharma Balasubiramani
2024-02-05 12:50 ` Nicolas Ferre
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240205110609.217022-3-dharma.b@microchip.com \
--to=dharma.b@microchip.com \
--cc=Jason@zx2c4.com \
--cc=Laurent.pinchart@ideasonboard.com \
--cc=airlied@gmail.com \
--cc=alexandre.belloni@bootlin.com \
--cc=andrzej.hajda@intel.com \
--cc=arnd@arndb.de \
--cc=claudiu.beznea@tuxon.dev \
--cc=conor+dt@kernel.org \
--cc=daniel@ffwll.ch \
--cc=devicetree@vger.kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=geert+renesas@glider.be \
--cc=hari.prasathge@microchip.com \
--cc=jernej.skrabec@gmail.com \
--cc=jonas@kwiboo.se \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=maarten.lankhorst@linux.intel.com \
--cc=manikandan.m@microchip.com \
--cc=mripard@kernel.org \
--cc=neil.armstrong@linaro.org \
--cc=nicolas.ferre@microchip.com \
--cc=rdunlap@infradead.org \
--cc=rfoss@kernel.org \
--cc=rientjes@google.com \
--cc=robh+dt@kernel.org \
--cc=tzimmermann@suse.de \
--cc=vbabka@suse.cz \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).