Igt-dev Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: "Lisovskiy, Stanislav" <stanislav.lisovskiy@intel.com>
To: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Cc: igt-dev@lists.freedesktop.org
Subject: Re: [igt-dev] [PATCH i-g-t] tests/kms_flip_scaled_crc: try to set mode to 1080p during test
Date: Tue, 26 Jan 2021 13:28:42 +0200	[thread overview]
Message-ID: <20210126112842.GA8075@intel.com> (raw)
In-Reply-To: <20210124144002.5741-1-juhapekka.heikkila@gmail.com>

On Sun, Jan 24, 2021 at 04:40:02PM +0200, Juha-Pekka Heikkila wrote:
> Different default resolutions will affect test execution, try to normalize
> situation by always going to 1080p resolution. If this test will run on
> connector which doesn't have 1080p resolution, default resolution will be
> used. On gen<11 will be used 480p
> 
> v2 (Stan): Use igt functions for modesetting. Change igt_warn to igt_debug
> because there's one ICL in intel CI with eDP that would show up warnings
> randomly depending which machine run which test.
> 
> Signed-off-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>

Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>

> ---
>  tests/kms_flip_scaled_crc.c | 85 ++++++++++++++++++++-----------------
>  1 file changed, 45 insertions(+), 40 deletions(-)
> 
> diff --git a/tests/kms_flip_scaled_crc.c b/tests/kms_flip_scaled_crc.c
> index 93d8031f7..f77484063 100644
> --- a/tests/kms_flip_scaled_crc.c
> +++ b/tests/kms_flip_scaled_crc.c
> @@ -35,6 +35,8 @@ typedef struct {
>  	struct igt_fb small_fb;
>  	struct igt_fb big_fb;
>  	igt_pipe_crc_t *pipe_crc;
> +	uint32_t attemptmodewidth;
> +	uint32_t attemptmodeheight;
>  } data_t;
>  
>  const struct {
> @@ -133,8 +135,7 @@ static void test_flip_to_scaled(data_t *data, uint32_t index, enum pipe pipe,
>  {
>  	igt_plane_t *primary;
>  	igt_crc_t small_crc, big_crc;
> -
> -	drmModeModeInfo *mode;
> +	drmModeModeInfoPtr modetoset = NULL;
>  	struct drm_event_vblank ev;
>  	int ret;
>  
> @@ -142,41 +143,24 @@ static void test_flip_to_scaled(data_t *data, uint32_t index, enum pipe pipe,
>  
>  	igt_debug("running on output %s pipe %s\n", output->name,
>  		  kmstest_pipe_name(pipe));
> +
>  	if (data->big_fb.fb_id == 0) {
> -		mode = igt_output_get_mode(output);
> -
> -		// big fb will be 4k unless running on older than ICL
> -		if (data->gen < 11) {
> -			setup_fb(data, &data->small_fb,
> -				 min(mode->hdisplay, 640),
> -				 min(mode->vdisplay, 480),
> -				 flip_scenario_test[index].firstformat,
> -				 flip_scenario_test[index].firstmodifier);
> -
> -			setup_fb(data, &data->big_fb,
> -				 1280, 960,
> -				 flip_scenario_test[index].secondformat,
> -				 flip_scenario_test[index].secondmodifier);
> -			igt_debug("small fb %dx%d\n", data->small_fb.width,
> -			          data->small_fb.height);
> -			igt_debug("big fb %dx%d\n", data->big_fb.width,
> -			          data->big_fb.height);
> -		} else {
> -			setup_fb(data, &data->small_fb,
> -				 min(mode->hdisplay, 1920),
> -				 min(mode->vdisplay, 1080),
> -				 flip_scenario_test[index].firstformat,
> -				 flip_scenario_test[index].firstmodifier);
> -
> -			setup_fb(data, &data->big_fb,
> -				 3840, 2160,
> -				 flip_scenario_test[index].secondformat,
> -				 flip_scenario_test[index].secondmodifier);
> -			igt_debug("small fb %dx%d\n", data->small_fb.width,
> -			          data->small_fb.height);
> -			igt_debug("big fb %dx%d\n", data->big_fb.width,
> -			          data->big_fb.height);
> -		}
> +		setup_fb(data, &data->small_fb,
> +				data->attemptmodewidth,
> +				data->attemptmodeheight,
> +				flip_scenario_test[index].firstformat,
> +				flip_scenario_test[index].firstmodifier);
> +
> +		setup_fb(data, &data->big_fb,
> +				data->attemptmodewidth * 2,
> +				data->attemptmodeheight * 2,
> +				flip_scenario_test[index].secondformat,
> +				flip_scenario_test[index].secondmodifier);
> +
> +		igt_debug("small fb %dx%d\n", data->small_fb.width,
> +				data->small_fb.height);
> +		igt_debug("big fb %dx%d\n", data->big_fb.width,
> +				data->big_fb.height);
>  	}
>  
>  	igt_output_set_pipe(output, pipe);
> @@ -186,13 +170,26 @@ static void test_flip_to_scaled(data_t *data, uint32_t index, enum pipe pipe,
>  				  NULL);
>  	data->pipe_crc = igt_pipe_crc_new(data->drm_fd, pipe,
>  					  INTEL_PIPE_CRC_SOURCE_AUTO);
> -	igt_pipe_crc_start(data->pipe_crc);
> +
> +	for (int i = 0; i < output->config.connector->count_modes; i++) {
> +		if (output->config.connector->modes[i].hdisplay == data->attemptmodewidth &&
> +		   output->config.connector->modes[i].vdisplay == data->attemptmodeheight) {
> +			modetoset = &output->config.connector->modes[i];
> +			break;
> +		   }
> +	}
> +
> +	if (!modetoset)
> +		igt_debug("%dp mode was not found from connector, will continue with default. This may cause cdclk to fail this test.\n",
> +			  data->attemptmodeheight);
> +	else
> +		igt_output_override_mode(output, modetoset);
>  
>  	igt_plane_set_position(primary, 0, 0);
>  	igt_plane_set_fb(primary, &data->small_fb);
> +	igt_display_commit_atomic(&data->display, DRM_MODE_ATOMIC_ALLOW_MODESET, NULL);
>  
> -	igt_display_commit_atomic(&data->display,
> -				  DRM_MODE_ATOMIC_ALLOW_MODESET, NULL);
> +	igt_pipe_crc_start(data->pipe_crc);
>  	igt_pipe_crc_get_current(data->drm_fd, data->pipe_crc, &small_crc);
>  
>  	igt_plane_set_fb(primary, &data->big_fb);
> @@ -203,7 +200,7 @@ static void test_flip_to_scaled(data_t *data, uint32_t index, enum pipe pipe,
>  					    DRM_MODE_PAGE_FLIP_EVENT, NULL);
>  
>  	igt_require_f(ret != -ERANGE,
> -		      "Platform scaling limits exceeded, skipping.");
> +		      "Platform scaling limits exceeded, skipping.\n");
>  	igt_assert_eq(ret, 0);
>  
>  	igt_assert(read(data->drm_fd, &ev, sizeof(ev)) == sizeof(ev));
> @@ -230,6 +227,14 @@ igt_main
>  		igt_require(data.display.is_atomic);
>  		igt_require_pipe_crc(data.drm_fd);
>  		kmstest_set_vt_graphics_mode();
> +
> +		if (data.gen < 11) {
> +			data.attemptmodewidth = 640;
> +			data.attemptmodeheight = 480;
> +		} else {
> +			data.attemptmodewidth = 1920;
> +			data.attemptmodeheight = 1080;
> +		}
>  	}
>  
>  	for (int index = 0; index < ARRAY_SIZE(flip_scenario_test); index++) {
> -- 
> 2.28.0
> 
> _______________________________________________
> igt-dev mailing list
> igt-dev@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/igt-dev
_______________________________________________
igt-dev mailing list
igt-dev@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/igt-dev

  parent reply	other threads:[~2021-01-26 11:27 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-01-24 14:40 [igt-dev] [PATCH i-g-t] tests/kms_flip_scaled_crc: try to set mode to 1080p during test Juha-Pekka Heikkila
2021-01-24 15:16 ` [igt-dev] ✓ Fi.CI.BAT: success for tests/kms_flip_scaled_crc: try to set mode to 1080p during test (rev2) Patchwork
2021-01-24 17:19 ` [igt-dev] ✗ Fi.CI.IGT: failure " Patchwork
2021-01-24 20:35   ` Juha-Pekka Heikkilä
2021-01-25  2:30     ` Vudum, Lakshminarayana
2021-01-25  2:23 ` [igt-dev] ✓ Fi.CI.IGT: success " Patchwork
2021-01-26 11:28 ` Lisovskiy, Stanislav [this message]
  -- strict thread matches above, loose matches on Subject: below --
2021-01-22  8:41 [igt-dev] [PATCH i-g-t] tests/kms_flip_scaled_crc: try to set mode to 1080p during test Juha-Pekka Heikkila
2021-01-22 11:44 ` Lisovskiy, Stanislav

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210126112842.GA8075@intel.com \
    --to=stanislav.lisovskiy@intel.com \
    --cc=igt-dev@lists.freedesktop.org \
    --cc=juhapekka.heikkila@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox