From: Jani Nikula <jani.nikula@linux.intel.com>
To: Rodrigo Vivi <rodrigo.vivi@intel.com>,
Jyoti Yadav <jyoti.r.yadav@intel.com>
Cc: igt-dev@lists.freedesktop.org, intel-gfx@lists.freedesktop.org,
Lakshmi <lakshminarayana.vudum@intel.com>
Subject: Re: [igt-dev] [PATCH] [intel-gfx] [PATCH i-g-t] tests/pm_backlight.c : Brightness test with DPMS and System suspend.
Date: Fri, 28 Sep 2018 16:37:36 +0300 [thread overview]
Message-ID: <875zypspy7.fsf@intel.com> (raw)
In-Reply-To: <20180831140954.GF2219@intel.com>
On Fri, 31 Aug 2018, Rodrigo Vivi <rodrigo.vivi@intel.com> wrote:
> On Fri, Aug 31, 2018 at 12:39:05AM -0400, Jyoti Yadav wrote:
>> From: Jyoti <jyoti.r.yadav@intel.com>
>>
>> BIOS programs few of PWM related registers during initial boot.
>> But during System suspend those registers are cleared.
>> This test aim to check whether display programs those registers properly after
>> system resume.
>> Also checks brightness programming during DPMS ON/OFF cycle to check backlight
>> programming is done properly from display side.
>>
>> v2 : Optimize the code to avoid code redundancy. (Rodrigo)
>>
>> Signed-off-by: Jyoti Yadav <jyoti.r.yadav@intel.com>
>
> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
>
> and pushed...
Jyoti, please sign up on [1] so we can involve you in bug reports.
This patch, or commit 377752242995 ("tests/pm_backlight.c : Brightness
test with DPMS and System suspend."), appears to cause bug [2]. The
suspend test goes on to use the sysfs interface before the backlight has
been re-enabled after resume, failing the test.
BR,
Jani.
[1] https://bugs.freedesktop.org
[2] https://bugs.freedesktop.org/show_bug.cgi?id=107847
>
> Thanks,
> Rodrigo.
>
>> ---
>> tests/pm_backlight.c | 30 ++++++++++++++++++++++++++++--
>> 1 file changed, 28 insertions(+), 2 deletions(-)
>>
>> diff --git a/tests/pm_backlight.c b/tests/pm_backlight.c
>> index a695f90..8b5c79d 100644
>> --- a/tests/pm_backlight.c
>> +++ b/tests/pm_backlight.c
>> @@ -47,6 +47,7 @@ struct context {
>> #define FADESPEED 100 /* milliseconds between steps */
>>
>> IGT_TEST_DESCRIPTION("Basic backlight sysfs test");
>> +static int8_t *pm_data = NULL;
>>
>> static int backlight_read(int *result, const char *fname)
>> {
>> @@ -150,19 +151,38 @@ static void test_fade(struct context *context)
>> nanosleep(&ts, NULL);
>> }
>> }
>> +static void test_fade_with_dpms(struct context *context, igt_output_t *output)
>> +{
>> + bool has_runtime_pm;
>> + has_runtime_pm = igt_setup_runtime_pm();
>> + igt_info("Runtime PM support: %d\n", has_runtime_pm);
>> + igt_assert(has_runtime_pm);
>> + kmstest_set_connector_dpms(output->display->drm_fd, output->config.connector, DRM_MODE_DPMS_OFF);
>> + igt_assert(igt_wait_for_pm_status(IGT_RUNTIME_PM_STATUS_SUSPENDED));
>> + kmstest_set_connector_dpms(output->display->drm_fd, output->config.connector, DRM_MODE_DPMS_ON);
>> + igt_assert(igt_wait_for_pm_status(IGT_RUNTIME_PM_STATUS_ACTIVE));
>> + test_fade(context);
>> +}
>> +static void test_fade_with_suspend(struct context *context, igt_output_t *output)
>> +{
>> + kmstest_set_connector_dpms(output->display->drm_fd, output->config.connector, DRM_MODE_DPMS_OFF);
>> + igt_assert(igt_wait_for_pm_status(IGT_RUNTIME_PM_STATUS_SUSPENDED));
>> + igt_system_suspend_autoresume(SUSPEND_STATE_MEM, SUSPEND_TEST_NONE);
>> + test_fade(context);
>> +}
>>
>> igt_main
>> {
>> struct context context = {0};
>> int old;
>> igt_display_t display;
>> + igt_output_t *output;
>> struct igt_fb fb;
>>
>> igt_skip_on_simulation();
>>
>> igt_fixture {
>> enum pipe pipe;
>> - igt_output_t *output;
>> bool found = false;
>> char full_name[32] = {};
>> char *name;
>> @@ -187,7 +207,6 @@ igt_main
>> for_each_pipe_with_valid_output(&display, pipe, output) {
>> if (strcmp(name + 6, output->name))
>> continue;
>> -
>> found = true;
>> break;
>> }
>> @@ -205,6 +224,7 @@ igt_main
>> igt_plane_set_fb(primary, &fb);
>>
>> igt_display_commit2(&display, display.is_atomic ? COMMIT_ATOMIC : COMMIT_LEGACY);
>> + pm_data = igt_pm_enable_sata_link_power_management();
>> }
>>
>> igt_subtest("basic-brightness")
>> @@ -213,6 +233,10 @@ igt_main
>> test_bad_brightness(&context);
>> igt_subtest("fade")
>> test_fade(&context);
>> + igt_subtest("fade_with_dpms")
>> + test_fade_with_dpms(&context, output);
>> + igt_subtest("fade_with_suspend")
>> + test_fade_with_suspend(&context, output);
>>
>> igt_fixture {
>> /* Restore old brightness */
>> @@ -220,6 +244,8 @@ igt_main
>>
>> igt_display_fini(&display);
>> igt_remove_fb(display.drm_fd, &fb);
>> + igt_pm_restore_sata_link_power_management(pm_data);
>> + free(pm_data);
>> close(display.drm_fd);
>> }
>> }
>> --
>> 1.9.1
>>
>> _______________________________________________
>> igt-dev mailing list
>> igt-dev@lists.freedesktop.org
>> https://lists.freedesktop.org/mailman/listinfo/igt-dev
> _______________________________________________
> igt-dev mailing list
> igt-dev@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/igt-dev
--
Jani Nikula, Intel Open Source Graphics Center
_______________________________________________
igt-dev mailing list
igt-dev@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/igt-dev
next prev parent reply other threads:[~2018-09-28 13:37 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-08-31 4:39 [igt-dev] [PATCH] [intel-gfx] [PATCH i-g-t] tests/pm_backlight.c : Brightness test with DPMS and System suspend Jyoti Yadav
2018-08-31 4:58 ` [igt-dev] ✓ Fi.CI.BAT: success for tests/pm_backlight.c : Brightness test with DPMS and System suspend. (rev4) Patchwork
2018-08-31 7:17 ` [igt-dev] ✓ Fi.CI.IGT: " Patchwork
2018-08-31 14:09 ` [igt-dev] [PATCH] [intel-gfx] [PATCH i-g-t] tests/pm_backlight.c : Brightness test with DPMS and System suspend Rodrigo Vivi
2018-09-28 13:37 ` Jani Nikula [this message]
-- strict thread matches above, loose matches on Subject: below --
2018-08-23 12:16 Jyoti Yadav
2018-08-30 0:40 ` Rodrigo Vivi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=875zypspy7.fsf@intel.com \
--to=jani.nikula@linux.intel.com \
--cc=igt-dev@lists.freedesktop.org \
--cc=intel-gfx@lists.freedesktop.org \
--cc=jyoti.r.yadav@intel.com \
--cc=lakshminarayana.vudum@intel.com \
--cc=rodrigo.vivi@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).