From: "Rob Herring (Arm)" <robh@kernel.org>
To: Lukasz Majewski <lukma@denx.de>
Cc: imx@lists.linux.dev, Fabio Estevam <festevam@gmail.com>,
Sascha Hauer <s.hauer@pengutronix.de>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Pengutronix Kernel Team <kernel@pengutronix.de>,
linux-arm-kernel@lists.infradead.org,
Conor Dooley <conor+dt@kernel.org>,
devicetree@vger.kernel.org, Shawn Guo <shawnguo@kernel.org>,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH v7 1/2] dt-bindings: arm: Document the btt3 i.MX28 based board
Date: Wed, 25 Sep 2024 21:42:22 -0500 [thread overview]
Message-ID: <172731846767.2423678.10609820762622388181.robh@kernel.org> (raw)
In-Reply-To: <20240925143129.4081815-1-lukma@denx.de>
On Wed, 25 Sep 2024 16:31:28 +0200, Lukasz Majewski wrote:
> The imx287 based btt3 board is very similar to xea in terms of used SOM
> module.
>
> Signed-off-by: Lukasz Majewski <lukma@denx.de>
> ---
> Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
My bot found new DTB warnings on the .dts files added or changed in this
series.
Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.
If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:
pip3 install dtschema --upgrade
New warnings running 'make CHECK_DTBS=y nxp/mxs/imx28-btt3-0.dtb nxp/mxs/imx28-btt3-1.dtb nxp/mxs/imx28-btt3-2.dtb' for 20240925143129.4081815-1-lukma@denx.de:
arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: /apb@80000000/apbh-bus@80000000/interrupt-controller@80000000: failed to match any schema with compatible: ['fsl,imx28-icoll', 'fsl,icoll']
arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: /apb@80000000/apbh-bus@80000000/interrupt-controller@80000000: failed to match any schema with compatible: ['fsl,imx28-icoll', 'fsl,icoll']
arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: nand-controller@8000c000: #size-cells: 0 was expected
from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: nand-controller@8000c000: #size-cells: 0 was expected
from schema $id: http://devicetree.org/schemas/mtd/nand-controller.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: spi@80010000: $nodename:0: 'spi@80010000' does not match '^mmc(@.*)?$'
from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: spi@80010000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'bus-width', 'clocks', 'non-removable', 'vmmc-supply' were unexpected)
from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: spi@80012000: $nodename:0: 'spi@80012000' does not match '^mmc(@.*)?$'
from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: spi@80012000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'bus-width', 'clocks', 'keep-power-in-suspend', 'mmc-pwrseq', 'no-1-8-v', 'non-removable', 'pm-ignore-notify', 'vmmc-supply', 'wlan@1' were unexpected)
from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: spi@80014000: Unevaluated properties are not allowed ('clocks' was unexpected)
from schema $id: http://devicetree.org/schemas/spi/mxs-spi.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: spi@80016000: Unevaluated properties are not allowed ('clocks' was unexpected)
from schema $id: http://devicetree.org/schemas/spi/mxs-spi.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: /apb@80000000/apbh-bus@80000000/interrupt-controller@80000000: failed to match any schema with compatible: ['fsl,imx28-icoll', 'fsl,icoll']
arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: /apb@80000000/apbh-bus@80000000/interrupt-controller@80000000: failed to match any schema with compatible: ['fsl,imx28-icoll', 'fsl,icoll']
arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: nand-controller@8000c000: #size-cells: 0 was expected
from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: nand-controller@8000c000: #size-cells: 0 was expected
from schema $id: http://devicetree.org/schemas/mtd/nand-controller.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: pinctrl@80018000: compatible: ['fsl,imx28-pinctrl', 'simple-bus'] is too long
from schema $id: http://devicetree.org/schemas/gpio/gpio-mxs.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: pinctrl@80018000: 'auart0-2pins@0', 'auart0@0', 'auart1-2pins@0', 'auart1@0', 'auart2-2pins@0', 'auart2-2pins@1', 'auart2-pins@0', 'auart3-2pins@0', 'auart3-2pins@1', 'auart3@0', 'auart4@0', 'auart4@1', 'can0@0', 'can1@0', 'duart-4pins@0', 'duart@0', 'duart@1', 'gpmi-nand@0', 'gpmi-status-cfg@0', 'hog@0', 'hog@1', 'i2c0@0', 'i2c0@1', 'i2c1@0', 'i2c1@1', 'keypad-bttc@0', 'lcdif-16bit@0', 'lcdif-18bit@0', 'lcdif-24bit@0', 'lcdif-bttc@0', 'lcdif-bttc@1', 'lcdif-sync@0', 'mac0@0', 'mac0@1', 'mac1@0', 'mmc0-4bit@0', 'mmc0-8bit@0', 'mmc0-cd-cfg@0', 'mmc0-sck-cfg@0', 'mmc1-4bit@0', 'mmc1-cd-cfg@0', 'mmc1-sck-cfg@0', 'mmc2-4bit@0', 'mmc2-4bit@1', 'mmc2-cd-cfg@0', 'mmc2-sck-cfg@0', 'mmc2-sck-cfg@1', 'pwm0@0', 'pwm2@0', 'pwm3@0', 'pwm3@1', 'pwm4@0', 'saif0@0', 'saif0@1', 'saif1@0', 'spi2@0', 'spi3@0', 'spi3@1', 'ssp1-sdio@0', 'usb0@0', 'usb0@1', 'usb0id1@0', 'usb0id@0', 'usb1@0', 'usb1@1', 'wifi_en_pin@0' do not match any of the regexes: 'gpio@[0-9]+$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/gpio/gpio-mxs.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: spi@80010000: $nodename:0: 'spi@80010000' does not match '^mmc(@.*)?$'
from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: spi@80010000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'bus-width', 'clocks', 'non-removable', 'vmmc-supply' were unexpected)
from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: /apb@80000000/apbh-bus@80000000/interrupt-controller@80000000: failed to match any schema with compatible: ['fsl,imx28-icoll', 'fsl,icoll']
arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: spi@80012000: $nodename:0: 'spi@80012000' does not match '^mmc(@.*)?$'
from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: spi@80012000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'bus-width', 'clocks', 'keep-power-in-suspend', 'mmc-pwrseq', 'no-1-8-v', 'non-removable', 'pm-ignore-notify', 'vmmc-supply', 'wlan@1' were unexpected)
from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: /apb@80000000/apbh-bus@80000000/interrupt-controller@80000000: failed to match any schema with compatible: ['fsl,imx28-icoll', 'fsl,icoll']
arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: spi@80014000: Unevaluated properties are not allowed ('clocks' was unexpected)
from schema $id: http://devicetree.org/schemas/spi/mxs-spi.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: nand-controller@8000c000: #size-cells: 0 was expected
from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: nand-controller@8000c000: #size-cells: 0 was expected
from schema $id: http://devicetree.org/schemas/mtd/nand-controller.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: spi@80016000: Unevaluated properties are not allowed ('clocks' was unexpected)
from schema $id: http://devicetree.org/schemas/spi/mxs-spi.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: spi@80010000: $nodename:0: 'spi@80010000' does not match '^mmc(@.*)?$'
from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: spi@80010000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'bus-width', 'clocks', 'non-removable', 'vmmc-supply' were unexpected)
from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: spi@80012000: $nodename:0: 'spi@80012000' does not match '^mmc(@.*)?$'
from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: spi@80012000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'bus-width', 'clocks', 'keep-power-in-suspend', 'mmc-pwrseq', 'no-1-8-v', 'non-removable', 'pm-ignore-notify', 'vmmc-supply', 'wlan@1' were unexpected)
from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: spi@80014000: Unevaluated properties are not allowed ('clocks' was unexpected)
from schema $id: http://devicetree.org/schemas/spi/mxs-spi.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: spi@80016000: Unevaluated properties are not allowed ('clocks' was unexpected)
from schema $id: http://devicetree.org/schemas/spi/mxs-spi.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: pinctrl@80018000: compatible: ['fsl,imx28-pinctrl', 'simple-bus'] is too long
from schema $id: http://devicetree.org/schemas/gpio/gpio-mxs.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: pinctrl@80018000: 'auart0-2pins@0', 'auart0@0', 'auart1-2pins@0', 'auart1@0', 'auart2-2pins@0', 'auart2-2pins@1', 'auart2-pins@0', 'auart3-2pins@0', 'auart3-2pins@1', 'auart3@0', 'auart4@0', 'auart4@1', 'can0@0', 'can1@0', 'duart-4pins@0', 'duart@0', 'duart@1', 'gpmi-nand@0', 'gpmi-status-cfg@0', 'hog@0', 'hog@1', 'i2c0@0', 'i2c0@1', 'i2c1@0', 'i2c1@1', 'keypad-bttc@0', 'lcdif-16bit@0', 'lcdif-18bit@0', 'lcdif-24bit@0', 'lcdif-bttc@0', 'lcdif-bttc@1', 'lcdif-sync@0', 'mac0@0', 'mac0@1', 'mac1@0', 'mmc0-4bit@0', 'mmc0-8bit@0', 'mmc0-cd-cfg@0', 'mmc0-sck-cfg@0', 'mmc1-4bit@0', 'mmc1-cd-cfg@0', 'mmc1-sck-cfg@0', 'mmc2-4bit@0', 'mmc2-4bit@1', 'mmc2-cd-cfg@0', 'mmc2-sck-cfg@0', 'mmc2-sck-cfg@1', 'pwm0@0', 'pwm2@0', 'pwm3@0', 'pwm3@1', 'pwm4@0', 'saif0@0', 'saif0@1', 'saif1@0', 'spi2@0', 'spi3@0', 'spi3@1', 'ssp1-sdio@0', 'usb0@0', 'usb0@1', 'usb0id1@0', 'usb0id@0', 'usb1@0', 'usb1@1', 'wifi_en_pin@0' do not match any of the regexes: 'gpio@[0-9]+$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/gpio/gpio-mxs.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: pinctrl@80018000: compatible: ['fsl,imx28-pinctrl', 'simple-bus'] is too long
from schema $id: http://devicetree.org/schemas/gpio/gpio-mxs.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: pinctrl@80018000: 'auart0-2pins@0', 'auart0@0', 'auart1-2pins@0', 'auart1@0', 'auart2-2pins@0', 'auart2-2pins@1', 'auart2-pins@0', 'auart3-2pins@0', 'auart3-2pins@1', 'auart3@0', 'auart4@0', 'auart4@1', 'can0@0', 'can1@0', 'duart-4pins@0', 'duart@0', 'duart@1', 'gpmi-nand@0', 'gpmi-status-cfg@0', 'hog@0', 'hog@1', 'i2c0@0', 'i2c0@1', 'i2c1@0', 'i2c1@1', 'keypad-bttc@0', 'lcdif-16bit@0', 'lcdif-18bit@0', 'lcdif-24bit@0', 'lcdif-bttc@0', 'lcdif-bttc@1', 'lcdif-sync@0', 'mac0@0', 'mac0@1', 'mac1@0', 'mmc0-4bit@0', 'mmc0-8bit@0', 'mmc0-cd-cfg@0', 'mmc0-sck-cfg@0', 'mmc1-4bit@0', 'mmc1-cd-cfg@0', 'mmc1-sck-cfg@0', 'mmc2-4bit@0', 'mmc2-4bit@1', 'mmc2-cd-cfg@0', 'mmc2-sck-cfg@0', 'mmc2-sck-cfg@1', 'pwm0@0', 'pwm2@0', 'pwm3@0', 'pwm3@1', 'pwm4@0', 'saif0@0', 'saif0@1', 'saif1@0', 'spi2@0', 'spi3@0', 'spi3@1', 'ssp1-sdio@0', 'usb0@0', 'usb0@1', 'usb0id1@0', 'usb0id@0', 'usb1@0', 'usb1@1', 'wifi_en_pin@0' do not match any of the regexes: 'gpio@[0-9]+$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/gpio/gpio-mxs.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: /apb@80000000/apbh-bus@80000000/digctl@8001c000: failed to match any schema with compatible: ['fsl,imx28-digctl', 'fsl,imx23-digctl']
arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: /apb@80000000/apbh-bus@80000000/digctl@8001c000: failed to match any schema with compatible: ['fsl,imx28-digctl', 'fsl,imx23-digctl']
arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: /apb@80000000/apbh-bus@80000000/digctl@8001c000: failed to match any schema with compatible: ['fsl,imx28-digctl', 'fsl,imx23-digctl']
arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: /apb@80000000/apbh-bus@80000000/digctl@8001c000: failed to match any schema with compatible: ['fsl,imx28-digctl', 'fsl,imx23-digctl']
arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: /apb@80000000/apbx-bus@80040000/lradc@80050000: failed to match any schema with compatible: ['fsl,imx28-lradc']
arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: /apb@80000000/apbx-bus@80040000/timrot@80068000: failed to match any schema with compatible: ['fsl,imx28-timrot', 'fsl,timrot']
arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: /apb@80000000/apbx-bus@80040000/timrot@80068000: failed to match any schema with compatible: ['fsl,imx28-timrot', 'fsl,timrot']
arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: /apb@80000000/apbh-bus@80000000/digctl@8001c000: failed to match any schema with compatible: ['fsl,imx28-digctl', 'fsl,imx23-digctl']
arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: /apb@80000000/apbh-bus@80000000/digctl@8001c000: failed to match any schema with compatible: ['fsl,imx28-digctl', 'fsl,imx23-digctl']
arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: /apb@80000000/apbx-bus@80040000/lradc@80050000: failed to match any schema with compatible: ['fsl,imx28-lradc']
arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: panel: compatible: ['panel-dpi'] is too short
from schema $id: http://devicetree.org/schemas/display/panel/panel-dpi.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: /apb@80000000/apbx-bus@80040000/timrot@80068000: failed to match any schema with compatible: ['fsl,imx28-timrot', 'fsl,timrot']
arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: /apb@80000000/apbx-bus@80040000/timrot@80068000: failed to match any schema with compatible: ['fsl,imx28-timrot', 'fsl,timrot']
arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: /apb@80000000/apbx-bus@80040000/lradc@80050000: failed to match any schema with compatible: ['fsl,imx28-lradc']
arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: /apb@80000000/apbx-bus@80040000/timrot@80068000: failed to match any schema with compatible: ['fsl,imx28-timrot', 'fsl,timrot']
arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: /apb@80000000/apbx-bus@80040000/timrot@80068000: failed to match any schema with compatible: ['fsl,imx28-timrot', 'fsl,timrot']
arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: panel: compatible: ['panel-dpi'] is too short
from schema $id: http://devicetree.org/schemas/display/panel/panel-dpi.yaml#
arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: panel: compatible: ['panel-dpi'] is too short
from schema $id: http://devicetree.org/schemas/display/panel/panel-dpi.yaml#
prev parent reply other threads:[~2024-09-26 2:42 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-09-25 14:31 [PATCH v7 1/2] dt-bindings: arm: Document the btt3 i.MX28 based board Lukasz Majewski
2024-09-25 14:31 ` [PATCH v7 2/2] ARM: dts: mxs: Add descriptions for imx287 based btt3-[012] devices Lukasz Majewski
2024-10-07 9:53 ` Lukasz Majewski
2024-10-07 10:57 ` Stefan Wahren
2024-10-08 11:35 ` Lukasz Majewski
2024-09-25 14:57 ` [PATCH v7 1/2] dt-bindings: arm: Document the btt3 i.MX28 based board Conor Dooley
2024-09-26 2:42 ` Rob Herring (Arm) [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=172731846767.2423678.10609820762622388181.robh@kernel.org \
--to=robh@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=imx@lists.linux.dev \
--cc=kernel@pengutronix.de \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=lukma@denx.de \
--cc=s.hauer@pengutronix.de \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox