From: Frank Li <Frank.Li@nxp.com>
To: frank.li@nxp.com, shawnguo@kernel.org
Cc: conor+dt@kernel.org, devicetree@vger.kernel.org,
imx@lists.linux.dev, krzk+dt@kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, robh@kernel.org
Subject: [PATCH 4/4] arm64: dts: ls2160a: Change I2C clock name to ipg to fix DTB_CHECK warning
Date: Fri, 31 May 2024 17:50:17 -0400 [thread overview]
Message-ID: <20240531215017.1969431-4-Frank.Li@nxp.com> (raw)
In-Reply-To: <20240531215017.1969431-1-Frank.Li@nxp.com>
dt_binding require I2C's clock name is "ipg". Change it to "ipg" from "i2c"
to fix below DTB_CHECK warning.
arch/arm64/boot/dts/freescale/fsl-lx2162a-qds.dtb: i2c@2010000: clock-names:0: 'ipg' was expected
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 16 ++++++++--------
1 file changed, 8 insertions(+), 8 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
index 96055593204ab..7dc98cb0ffc93 100644
--- a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
@@ -745,7 +745,7 @@ i2c0: i2c@2000000 {
#size-cells = <0>;
reg = <0x0 0x2000000 0x0 0x10000>;
interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "i2c";
+ clock-names = "ipg";
clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
QORIQ_CLK_PLL_DIV(16)>;
pinctrl-names = "default", "gpio";
@@ -761,7 +761,7 @@ i2c1: i2c@2010000 {
#size-cells = <0>;
reg = <0x0 0x2010000 0x0 0x10000>;
interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "i2c";
+ clock-names = "ipg";
clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
QORIQ_CLK_PLL_DIV(16)>;
pinctrl-names = "default", "gpio";
@@ -777,7 +777,7 @@ i2c2: i2c@2020000 {
#size-cells = <0>;
reg = <0x0 0x2020000 0x0 0x10000>;
interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "i2c";
+ clock-names = "ipg";
clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
QORIQ_CLK_PLL_DIV(16)>;
pinctrl-names = "default", "gpio";
@@ -793,7 +793,7 @@ i2c3: i2c@2030000 {
#size-cells = <0>;
reg = <0x0 0x2030000 0x0 0x10000>;
interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "i2c";
+ clock-names = "ipg";
clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
QORIQ_CLK_PLL_DIV(16)>;
pinctrl-names = "default", "gpio";
@@ -809,7 +809,7 @@ i2c4: i2c@2040000 {
#size-cells = <0>;
reg = <0x0 0x2040000 0x0 0x10000>;
interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "i2c";
+ clock-names = "ipg";
clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
QORIQ_CLK_PLL_DIV(16)>;
pinctrl-names = "default", "gpio";
@@ -825,7 +825,7 @@ i2c5: i2c@2050000 {
#size-cells = <0>;
reg = <0x0 0x2050000 0x0 0x10000>;
interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "i2c";
+ clock-names = "ipg";
clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
QORIQ_CLK_PLL_DIV(16)>;
pinctrl-names = "default", "gpio";
@@ -841,7 +841,7 @@ i2c6: i2c@2060000 {
#size-cells = <0>;
reg = <0x0 0x2060000 0x0 0x10000>;
interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "i2c";
+ clock-names = "ipg";
clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
QORIQ_CLK_PLL_DIV(16)>;
pinctrl-names = "default", "gpio";
@@ -857,7 +857,7 @@ i2c7: i2c@2070000 {
#size-cells = <0>;
reg = <0x0 0x2070000 0x0 0x10000>;
interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "i2c";
+ clock-names = "ipg";
clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
QORIQ_CLK_PLL_DIV(16)>;
pinctrl-names = "default", "gpio";
--
2.34.1
next prev parent reply other threads:[~2024-05-31 21:50 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-05-31 21:50 [PATCH 1/4] arm64: dts: ls1012a: Reorder sai dma-names to clean up DTB_CHECK warning Frank Li
2024-05-31 21:50 ` [PATCH 2/4] arm64: dts: ls1043a: Change I2C clock name to ipg to fix " Frank Li
2024-05-31 21:50 ` [PATCH 3/4] arm64: dts: ls208xa: " Frank Li
2024-05-31 21:50 ` Frank Li [this message]
2024-06-16 6:55 ` [PATCH 1/4] arm64: dts: ls1012a: Reorder sai dma-names to clean up " Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240531215017.1969431-4-Frank.Li@nxp.com \
--to=frank.li@nxp.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=imx@lists.linux.dev \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh@kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox