From: Shawn Guo <shawnguo2@yeah.net>
To: soc@kernel.org, arm@kernel.org
Cc: Shawn Guo <shawnguo@kernel.org>,
Fabio Estevam <festevam@gmail.com>,
kernel@pengutronix.de, imx@lists.linux.dev,
linux-arm-kernel@lists.infradead.org
Subject: [GIT PULL 5/5] i.MX arm64 device tree changes for 6.15
Date: Wed, 12 Mar 2025 15:40:05 +0800 [thread overview]
Message-ID: <20250312074005.663165-5-shawnguo2@yeah.net> (raw)
In-Reply-To: <20250312074005.663165-1-shawnguo2@yeah.net>
From: Shawn Guo <shawnguo@kernel.org>
The following changes since commit 2014c95afecee3e76ca4a56956a936e23283f05b:
Linux 6.14-rc1 (2025-02-02 15:39:26 -0800)
are available in the Git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git tags/imx-dt64-6.15
for you to fetch changes up to 5a690619426fc4b09c7fd3f40d3a69264ef3db0f:
arm64: dts: imx8qm-apalis: Remove compatible from SoM dtsi (2025-03-11 11:16:30 +0800)
----------------------------------------------------------------
i.MX arm64 device tree changes for 6.15:
- New board support: S32G-EVB/RDB, i.MX95 15x15 EVK, i.MX8MP Skov
revC BD500 and new 7" panel board, i.MX8MM phyboard polis PEB-AV-10
- A series from Ahmad Fatoum and Oleksij Rempel to flesh out
imx8mp-skov device trees, correcting PMIC board limits, adding display
pipeline, configuring uart1 for RS485, etc.
- A bunch of changes from Alexander Stein, adding PCIe support for
mba8xx, enabling jpeg encode and decode for tqma8xx, adding vcc-supply
for spi-nor, etc.
- A series from Chancel Liu to complete WM8960 power supplies for NXP
i.MX8 based boards
- A dozen of changes from Frank Li, enabling audio codec for imx8qm-mek,
adding PCIe EP for i.MX8Q, improving i.MX93 and i.MX95 support, etc.
- A number of changes from Frieder Schrempf to support reading SD_VSEL
signal for imx8m-kontron devices, fix SD card IO voltage control for
imx93-kontron
- A series from Teresa Remmet to improve imx8mm-phycore support, keeping
LDO3 on in suspend, adding overlays for devices without Ethernet PHY,
SPI NOR Flash, etc.
- A couple of changes from Xu Yang to enable usb3 support for
imx95-19x19-evk board
- Other random improvements and cleanups on various boards
----------------------------------------------------------------
Ahmad Fatoum (12):
arm64: dts: imx8mp-skov: correct PMIC board limits
arm64: dts: imx8mp-skov: operate CPU at 850 mV by default
arm64: dts: imx8mp-skov: use I2C5 for DDC
arm64: dts: imx8mp-skov: configure uart1 for RS485
arm64: dts: imx8mp: Add optional nominal drive mode DTSI
arm64: dts: imx8mp: add fsl,nominal-mode property into nominal.dtsi
arm64: dts: freescale: imx8mp-skov: configure LDB clock automatically
arm64: dts: freescale: imx8mp-skov: operate SoC in nominal mode
arm64: dts: imx8mp-skov: move I2C2 pin control group into DTSI
arm64: dts: imx8mp-skov: describe I2C bus recovery for all controllers
arm64: dts: imx8mp-skov: add revC BD500 board
arm64: dts: imx8mp-skov: support new 7" panel board
Alexander Stein (14):
arm64: dts: imx8-ss-hsio: Wire up DMA IRQ for PCIe
arm64: dts: tqma8xx: Add vcc-supply for spi-nor
arm64: dts: tqma8xx: enable jpeg encode and decode
arm64: dts: tqma8xx: Remove GPU TODO
arm64: dts: mba8xx: Add PCIe support
arm64: dts: freescale: imx93-tqma9352-mba93xxca: sort pinctrl nodes
arm64: dts: mba93xxca: Do not assert power-down pins
arm64: dts: tqma9352-mba93xx[cl]a: swap ethernet aliases
arm64: dts: freescale: tqma8mpql: Add vcc-supply for spi-nor
arm64: dts: freescale: tqma8mq: Add vcc-supply for spi-nor
arm64: dts: freescale: tqma8mqml: Add vcc-supply for spi-nor
arm64: dts: freescale: tqma8mqnl: Add vcc-supply for spi-nor
arm64: dts: imx8qm-ss-hsio: Wire up DMA IRQ for PCIe
arm64: dts: mba8xx: Remove invalid property disable-gpio
Andrej Picej (3):
arm64: dts: imx8mm-phycore-som: Fix bluetooth wakeup source
arm64: dts: imx8mm-phyboard-polis: Set RTC as wakeup-source
arm64: dts: imx8mm-phygate-tauri-l: Set RTC as wakeup-source
Chancel Liu (4):
arm64: dts: imx8mp-evk: Complete WM8960 power supplies
arm64: dts: imx8dxl-evk: Complete WM8960 power supplies
arm64: dts: imx8qm-mek: Complete WM8960 power supplies
arm64: dts: imx8qxp-mek: Complete WM8960 power supplies
Ciprian Marian Costea (4):
arm64: dts: s32g: add I2C[0..2] support for s32g2 and s32g3
arm64: dts: s32g: add common 'S32G-EVB' and 'S32G-RDB' board support
arm64: dts: s32g399a-rdb3: Add INA231 sensor entry over I2C4
arm64: dts: s32g: add FlexCAN[0..3] support for s32g2 and s32g3
Dominik Haller (1):
arm64: dts: imx8mm-phycore-som: Add overlay for rproc
Fabio Estevam (1):
arm64: dts: imx8mn-bsh-smm-s2pro: Remove invalid audio codec clock
Francesco Dolcini (2):
arm64: dts: freescale: imx8mm-verdin: Remove LVDS panel and backlight
arm64: dts: imx8qm-apalis: Remove compatible from SoM dtsi
Frank Li (12):
arm64: dts: imx8mq-librem5: remove undocument property 'extcon' for usb-pd@3f
arm64: dts: imx8qm-mek: add audio-codec cs42888 and related nodes
arm64: dts: imx8-ss-hsio: fix indentation in pcie node
arm64: dts: imx8q: add PCIe EP for i.MX8QM and i.MX8QXP
arm64: dts: imx8q: add PCIe EP overlay file for i.MX8QXP mek board
arm64: dts: imx95: add PCIe's msi-map and iommu-map property
arm64: dts: imx95: Add #io-channel-cells = <1> for adc node
arm64: dts: imx95: Add i3c1 and i3c2
arm64: dts: imx95: Add imx95-15x15-evk support
arm64: dts: im8mq-librem5: move dwc3 usb port under ports
arm64: dts: imx95: add ref clock for pcie nodes
arm64: dts: imx93: add ddr edac support
Frieder Schrempf (3):
arm64: dts: imx8mm-kontron: Add support for reading SD_VSEL signal
arm64: dts: imx93-kontron: Fix SD card IO voltage control
arm64: dts: imx8mp-kontron: Add support for reading SD_VSEL signal
Janine Hagemann (1):
arm64: dts: imx8mm-phyboard-polis: Add overlay for PEB-EVAL-01
Larisa Grigore (1):
arm64: dts: s32g: add the eDMA nodes
Laurentiu Mihalcea (2):
arm64: dts: imx8mp: add AUDIO_AXI_CLK_ROOT to AUDIOMIX block
arm64: dts: imx8mp: change AUDIO_AXI_CLK_ROOT freq. to 800MHz
Lucas Stach (1):
arm64: dts: imx8mp: configure GPU and NPU clocks to overdrive rate
Markus Niebel (2):
arm64: dts: imx8mp-tqma8mpql-mba8mpxl: change sound card model name
arm64: dts: mba8mx: change sound card model name
Mathew McBride (1):
arm64: dts: freescale: ten64: add usb hub definition
Oleksij Rempel (6):
arm64: dts: imx8mp-skov: describe HDMI display pipeline
arm64: dts: imx8mp-skov: describe LVDS display pipeline
arm64: dts: imx8mp-skov: describe mains fail detection
arm64: dts: imx8mp-skov: fix phy-mode
arm64: dts: imx8mp-skov: increase I2C clock frequency for RTC
arm64: dts: imx8mp-skov: add basic board as fallback
Rafael Beims (1):
arm64: dts: colibri-imx8x: Add missing gpio-line-names
Stefan Eichenberger (1):
arm64: dts: imx8-apalis: add clock configuration for 44.1 kHz hdmi audio
Teresa Remmet (5):
arm64: dts: imx8mm-phycore-som: Keep LDO3 on in suspend
arm64: dts: imx8mm-phycore-som: Remove magic-packet property
arm64: dts: imx8mm-phyboard-polis: Add support for PEB-AV-10
arm64: dts: imx8mm-phycore-som: Add no-eth phy overlay
arm64: dts: imx8mm-phycore-som: Add overlay to disable SPI NOR flash
Xu Yang (2):
arm64: dts: imx95: add usb3 related nodes
arm64: dts: imx95-19x19-evk: add typec nodes and enable usb3 node
Yannic Moog (3):
arm64: dts: imx8mm-phycore-som: add descriptions to nodes
arm64: dts: imx8mm-phyboard-polis: add RTC description
arm64: dts: imx8mm: move bulk of rtc properties to carrierboards
Yashwanth Varakala (2):
arm64: dts: imx8mm-phycore-som: Assign regulator for dsi to lvds bridge
arm64: dts: imx8mm-phyboard-polis: Assign missing regulator for bluetooth
arch/arm64/boot/dts/freescale/Makefile | 21 +
.../arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts | 44 +
.../arm64/boot/dts/freescale/imx8-apalis-v1.1.dtsi | 16 +
arch/arm64/boot/dts/freescale/imx8-ss-hsio.dtsi | 30 +-
arch/arm64/boot/dts/freescale/imx8dxl-evk.dts | 42 +
.../arm64/boot/dts/freescale/imx8mm-kontron-bl.dts | 10 +-
.../boot/dts/freescale/imx8mm-kontron-osm-s.dtsi | 7 +-
.../freescale/imx8mm-phyboard-polis-peb-av-10.dtso | 237 ++++
.../imx8mm-phyboard-polis-peb-eval-01.dtso | 72 ++
.../dts/freescale/imx8mm-phyboard-polis-rdk.dts | 17 +-
.../boot/dts/freescale/imx8mm-phycore-no-eth.dtso | 12 +
.../dts/freescale/imx8mm-phycore-no-spiflash.dtso | 16 +
.../boot/dts/freescale/imx8mm-phycore-rpmsg.dtso | 58 +
.../boot/dts/freescale/imx8mm-phycore-som.dtsi | 22 +-
.../boot/dts/freescale/imx8mm-phygate-tauri-l.dts | 11 +
.../arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi | 1 +
arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi | 21 -
.../boot/dts/freescale/imx8mn-bsh-smm-s2pro.dts | 1 -
.../arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi | 1 +
arch/arm64/boot/dts/freescale/imx8mp-evk.dts | 22 +
.../boot/dts/freescale/imx8mp-kontron-osm-s.dtsi | 7 +-
arch/arm64/boot/dts/freescale/imx8mp-nominal.dtsi | 64 ++
.../arm64/boot/dts/freescale/imx8mp-skov-basic.dts | 10 +
.../arm64/boot/dts/freescale/imx8mp-skov-reva.dtsi | 126 ++-
.../boot/dts/freescale/imx8mp-skov-revb-hdmi.dts | 45 +-
.../boot/dts/freescale/imx8mp-skov-revb-lt6.dts | 60 ++
.../freescale/imx8mp-skov-revb-mi1010ait-1cp1.dts | 30 +-
.../boot/dts/freescale/imx8mp-skov-revc-bd500.dts | 91 ++
.../dts/freescale/imx8mp-skov-revc-tian-g07017.dts | 81 ++
.../dts/freescale/imx8mp-tqma8mpql-mba8mpxl.dts | 2 +-
.../arm64/boot/dts/freescale/imx8mp-tqma8mpql.dtsi | 1 +
arch/arm64/boot/dts/freescale/imx8mp.dtsi | 23 +-
.../boot/dts/freescale/imx8mq-librem5-devkit.dts | 25 +-
arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi | 26 +-
arch/arm64/boot/dts/freescale/imx8mq-tqma8mq.dtsi | 1 +
.../boot/dts/freescale/imx8qm-apalis-v1.1.dtsi | 2 -
arch/arm64/boot/dts/freescale/imx8qm-apalis.dtsi | 2 -
arch/arm64/boot/dts/freescale/imx8qm-mek.dts | 112 ++
arch/arm64/boot/dts/freescale/imx8qm-ss-hsio.dtsi | 24 +-
.../boot/dts/freescale/imx8qxp-mek-pcie-ep.dtso | 22 +
arch/arm64/boot/dts/freescale/imx8qxp-mek.dts | 32 +
arch/arm64/boot/dts/freescale/imx8x-colibri.dtsi | 4 +-
.../boot/dts/freescale/imx93-kontron-osm-s.dtsi | 5 +-
.../dts/freescale/imx93-tqma9352-mba93xxca.dts | 54 +-
.../dts/freescale/imx93-tqma9352-mba93xxla.dts | 6 +-
arch/arm64/boot/dts/freescale/imx93.dtsi | 8 +
arch/arm64/boot/dts/freescale/imx95-15x15-evk.dts | 1130 ++++++++++++++++++++
arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts | 83 ++
arch/arm64/boot/dts/freescale/imx95.dtsi | 108 +-
arch/arm64/boot/dts/freescale/mba8mx.dtsi | 2 +-
arch/arm64/boot/dts/freescale/mba8xx.dtsi | 31 +-
arch/arm64/boot/dts/freescale/s32g2.dtsi | 141 +++
arch/arm64/boot/dts/freescale/s32g274a-evb.dts | 1 +
arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts | 1 +
arch/arm64/boot/dts/freescale/s32g3.dtsi | 150 +++
arch/arm64/boot/dts/freescale/s32g399a-rdb3.dts | 9 +
arch/arm64/boot/dts/freescale/s32gxxxa-evb.dtsi | 222 ++++
arch/arm64/boot/dts/freescale/s32gxxxa-rdb.dtsi | 170 +++
arch/arm64/boot/dts/freescale/tqma8xx.dtsi | 12 +-
59 files changed, 3397 insertions(+), 187 deletions(-)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtso
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-eval-01.dtso
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-phycore-no-eth.dtso
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-phycore-no-spiflash.dtso
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-phycore-rpmsg.dtso
create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-nominal.dtsi
create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-skov-basic.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-skov-revc-bd500.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-skov-revc-tian-g07017.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8qxp-mek-pcie-ep.dtso
create mode 100644 arch/arm64/boot/dts/freescale/imx95-15x15-evk.dts
create mode 100644 arch/arm64/boot/dts/freescale/s32gxxxa-evb.dtsi
create mode 100644 arch/arm64/boot/dts/freescale/s32gxxxa-rdb.dtsi
prev parent reply other threads:[~2025-03-12 7:40 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-03-12 7:40 [GIT PULL 1/5] i.MX drivers changes for 6.15 Shawn Guo
2025-03-12 7:40 ` [GIT PULL 2/5] i.MX SoC " Shawn Guo
2025-03-12 7:40 ` [GIT PULL 3/5] i.MX dt-bindings " Shawn Guo
2025-03-12 7:40 ` [GIT PULL 4/5] i.MX ARM device tree " Shawn Guo
2025-03-12 7:40 ` Shawn Guo [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250312074005.663165-5-shawnguo2@yeah.net \
--to=shawnguo2@yeah.net \
--cc=arm@kernel.org \
--cc=festevam@gmail.com \
--cc=imx@lists.linux.dev \
--cc=kernel@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=shawnguo@kernel.org \
--cc=soc@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).