Re: [PATCH v9 2/3] arm64: dts: imx95: add usb3 related nodes

[Alexander Stein <alexander.stein@ew.tq-group.com>]

Hi,

Am Mittwoch, 13. November 2024, 09:07:44 CET schrieb Xu Yang:
> Add usb3 phy and controller nodes for imx95.
> 
> Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
> 
> ---
> Changes in v2:
>  - no changes
> Changes in v3:
>  - no changes
> Changes in v4:
>  - reorder nodes
> Changes in v5:
>  - no changes
> Changes in v6:
>  - rebase to latest
> Changes in v7:
>  - no changes
> Changes in v8:
>  - no changes
> Changes in v9:
>  - no changes
> ---
>  arch/arm64/boot/dts/freescale/imx95.dtsi | 43 ++++++++++++++++++++++++
>  1 file changed, 43 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx95.dtsi b/arch/arm64/boot/dts/freescale/imx95.dtsi
> index 03661e76550f..e3faa8462759 100644
> --- a/arch/arm64/boot/dts/freescale/imx95.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx95.dtsi
> @@ -1473,6 +1473,49 @@ smmu: iommu@490d0000 {
>  			};
>  		};
>  
> +		usb3: usb@4c010010 {
> +			compatible = "fsl,imx95-dwc3", "fsl,imx8mp-dwc3";
> +			reg = <0x0 0x4c010010 0x0 0x04>,
> +			      <0x0 0x4c1f0000 0x0 0x20>;
> +			clocks = <&scmi_clk IMX95_CLK_HSIO>,
> +				 <&scmi_clk IMX95_CLK_32K>;
> +			clock-names = "hsio", "suspend";
> +			interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			ranges;
> +			power-domains = <&scmi_devpd IMX95_PD_HSIO_TOP>;
> +			dma-ranges = <0x0 0x0 0x0 0x0 0x10 0x0>;
> +			status = "disabled";
> +
> +			usb3_dwc3: usb@4c100000 {
> +				compatible = "snps,dwc3";
> +				reg = <0x0 0x4c100000 0x0 0x10000>;
> +				clocks = <&scmi_clk IMX95_CLK_HSIO>,
> +					 <&scmi_clk IMX95_CLK_24M>,
> +					 <&scmi_clk IMX95_CLK_32K>;
> +				clock-names = "bus_early", "ref", "suspend";
> +				interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
> +				phys = <&usb3_phy>, <&usb3_phy>;
> +				phy-names = "usb2-phy", "usb3-phy";
> +				snps,gfladj-refclk-lpm-sel-quirk;
> +				snps,parkmode-disable-ss-quirk;
> +				iommus = <&smmu 0xe>;
> +			};
> +		};
> +
> +		usb3_phy: phy@4c1f0040 {
> +			compatible = "fsl,imx95-usb-phy", "fsl,imx8mp-usb-phy";
> +			reg = <0x0 0x4c1f0040 0x0 0x40>,
> +			      <0x0 0x4c1fc000 0x0 0x100>;
> +			clocks = <&scmi_clk IMX95_CLK_HSIO>;
> +			clock-names = "phy";
> +			#phy-cells = <0>;
> +			power-domains = <&scmi_devpd IMX95_PD_HSIO_TOP>;
> +			orientation-switch;

This adds the orientation-switch to all imx95 based boards, which in turn
requires a port subnode.
This is incorrect if this USB interface is not connected to a USB Type-C
connector but an on-board USB hub.

Best regards,
Alexander

> +			status = "disabled";
> +		};
> +
>  		pcie0: pcie@4c300000 {
>  			compatible = "fsl,imx95-pcie";
>  			reg = <0 0x4c300000 0 0x10000>,
> 


-- 
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
http://www.tq-group.com/