[PATCH 08/22] drm/i915: split LVDS update code out of i9xx_crtc_mode_set

[Jesse Barnes <jbarnes@virtuousgeek.org>]

Just to make things clearer and reduce the size of this monstrosity.

v2: make sure 8xx PLL update function calls update_lvds too (Daniel)

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
---
 drivers/gpu/drm/i915/intel_display.c |  124 +++++++++++++++++++---------------
 1 files changed, 70 insertions(+), 54 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index cb8067a..c425471 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -5260,6 +5260,62 @@ static void i9xx_update_pll_dividers(struct drm_crtc *crtc,
 	}
 }
 
+static void intel_update_lvds(struct drm_crtc *crtc, intel_clock_t *clock,
+			      struct drm_display_mode *adjusted_mode)
+{
+	struct drm_device *dev = crtc->dev;
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+	int pipe = intel_crtc->pipe;
+	u32 temp, lvds_sync = 0;
+
+	temp = I915_READ(LVDS);
+	temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
+	if (pipe == 1) {
+		temp |= LVDS_PIPEB_SELECT;
+	} else {
+		temp &= ~LVDS_PIPEB_SELECT;
+	}
+	/* set the corresponsding LVDS_BORDER bit */
+	temp |= dev_priv->lvds_border_bits;
+	/* Set the B0-B3 data pairs corresponding to whether we're going to
+	 * set the DPLLs for dual-channel mode or not.
+	 */
+	if (clock->p2 == 7)
+		temp |= LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP;
+	else
+		temp &= ~(LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP);
+
+	/* It would be nice to set 24 vs 18-bit mode (LVDS_A3_POWER_UP)
+	 * appropriately here, but we need to look more thoroughly into how
+	 * panels behave in the two modes.
+	 */
+	/* set the dithering flag on LVDS as needed */
+	if (INTEL_INFO(dev)->gen >= 4) {
+		if (dev_priv->lvds_dither)
+			temp |= LVDS_ENABLE_DITHER;
+		else
+			temp &= ~LVDS_ENABLE_DITHER;
+	}
+	if (adjusted_mode->flags & DRM_MODE_FLAG_NHSYNC)
+		lvds_sync |= LVDS_HSYNC_POLARITY;
+	if (adjusted_mode->flags & DRM_MODE_FLAG_NVSYNC)
+		lvds_sync |= LVDS_VSYNC_POLARITY;
+	if ((temp & (LVDS_HSYNC_POLARITY | LVDS_VSYNC_POLARITY))
+	    != lvds_sync) {
+		char flags[2] = "-+";
+		DRM_INFO("Changing LVDS panel from "
+			 "(%chsync, %cvsync) to (%chsync, %cvsync)\n",
+			 flags[!(temp & LVDS_HSYNC_POLARITY)],
+			 flags[!(temp & LVDS_VSYNC_POLARITY)],
+			 flags[!(lvds_sync & LVDS_HSYNC_POLARITY)],
+			 flags[!(lvds_sync & LVDS_VSYNC_POLARITY)]);
+		temp &= ~(LVDS_HSYNC_POLARITY | LVDS_VSYNC_POLARITY);
+		temp |= lvds_sync;
+	}
+	I915_WRITE(LVDS, temp);
+}
+
 static void i9xx_update_pll(struct drm_crtc *crtc,
 			    struct drm_display_mode *mode,
 			    struct drm_display_mode *adjusted_mode,
@@ -5335,6 +5391,13 @@ static void i9xx_update_pll(struct drm_crtc *crtc,
 	POSTING_READ(DPLL(pipe));
 	udelay(150);
 
+	/* The LVDS pin pair needs to be on before the DPLLs are enabled.
+	 * This is an exception to the general rule that mode_set doesn't turn
+	 * things on.
+	 */
+	if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS))
+		intel_update_lvds(crtc, clock, adjusted_mode);
+
 	if (intel_pipe_has_type(crtc, INTEL_OUTPUT_DISPLAYPORT))
 		intel_dp_set_m_n(crtc, mode, adjusted_mode);
 
@@ -5409,6 +5472,13 @@ static void i8xx_update_pll(struct drm_crtc *crtc,
 	POSTING_READ(DPLL(pipe));
 	udelay(150);
 
+	/* The LVDS pin pair needs to be on before the DPLLs are enabled.
+	 * This is an exception to the general rule that mode_set doesn't turn
+	 * things on.
+	 */
+	if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS))
+		intel_update_lvds(crtc, clock, adjusted_mode);
+
 	/* The pixel multiplier can only be updated once the
 	 * DPLL is enabled and the clocks are stable.
 	 *
@@ -5437,8 +5507,6 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 	struct intel_encoder *encoder;
 	const intel_limit_t *limit;
 	int ret;
-	u32 temp;
-	u32 lvds_sync = 0;
 
 	list_for_each_entry(encoder, &mode_config->encoder_list, base.head) {
 		if (encoder->base.crtc != crtc)
@@ -5548,58 +5616,6 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 	DRM_DEBUG_KMS("Mode for pipe %c:\n", pipe == 0 ? 'A' : 'B');
 	drm_mode_debug_printmodeline(mode);
 
-	/* The LVDS pin pair needs to be on before the DPLLs are enabled.
-	 * This is an exception to the general rule that mode_set doesn't turn
-	 * things on.
-	 */
-	if (is_lvds) {
-		temp = I915_READ(LVDS);
-		temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
-		if (pipe == 1) {
-			temp |= LVDS_PIPEB_SELECT;
-		} else {
-			temp &= ~LVDS_PIPEB_SELECT;
-		}
-		/* set the corresponsding LVDS_BORDER bit */
-		temp |= dev_priv->lvds_border_bits;
-		/* Set the B0-B3 data pairs corresponding to whether we're going to
-		 * set the DPLLs for dual-channel mode or not.
-		 */
-		if (clock.p2 == 7)
-			temp |= LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP;
-		else
-			temp &= ~(LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP);
-
-		/* It would be nice to set 24 vs 18-bit mode (LVDS_A3_POWER_UP)
-		 * appropriately here, but we need to look more thoroughly into how
-		 * panels behave in the two modes.
-		 */
-		/* set the dithering flag on LVDS as needed */
-		if (INTEL_INFO(dev)->gen >= 4) {
-			if (dev_priv->lvds_dither)
-				temp |= LVDS_ENABLE_DITHER;
-			else
-				temp &= ~LVDS_ENABLE_DITHER;
-		}
-		if (adjusted_mode->flags & DRM_MODE_FLAG_NHSYNC)
-			lvds_sync |= LVDS_HSYNC_POLARITY;
-		if (adjusted_mode->flags & DRM_MODE_FLAG_NVSYNC)
-			lvds_sync |= LVDS_VSYNC_POLARITY;
-		if ((temp & (LVDS_HSYNC_POLARITY | LVDS_VSYNC_POLARITY))
-		    != lvds_sync) {
-			char flags[2] = "-+";
-			DRM_INFO("Changing LVDS panel from "
-				 "(%chsync, %cvsync) to (%chsync, %cvsync)\n",
-				 flags[!(temp & LVDS_HSYNC_POLARITY)],
-				 flags[!(temp & LVDS_VSYNC_POLARITY)],
-				 flags[!(lvds_sync & LVDS_HSYNC_POLARITY)],
-				 flags[!(lvds_sync & LVDS_VSYNC_POLARITY)]);
-			temp &= ~(LVDS_HSYNC_POLARITY | LVDS_VSYNC_POLARITY);
-			temp |= lvds_sync;
-		}
-		I915_WRITE(LVDS, temp);
-	}
-
 	if (HAS_PIPE_CXSR(dev)) {
 		if (intel_crtc->lowfreq_avail) {
 			DRM_DEBUG_KMS("enabling CxSR downclocking\n");
-- 
1.7.5.4