[PATCH] drm/i915: dsi: fix pipe-off timeout due to port vs. pipe disable ordering

[Imre Deak <imre.deak@intel.com>]

If we disable first the port (by disabling DPI) and only then the
display pipe the pipe-off flag will never be set, possibly leading to a
hanged pipe state at the next modeset-enable.

Note that according to the VLV2 display cluster HAS, we should disable
the port before the pipe. This doesn't seem to match reality based on
the above and it's also asymmetric with the enabling sequence, where we
first enable the port and then the pipe.

v2:
- send the panel shutdown command before stopping the pipe, since this
  is the recommended sequence (Shobhit)

Signed-off-by: Imre Deak <imre.deak@intel.com>
---
 drivers/gpu/drm/i915/intel_dsi.c | 25 ++++++++++++++++++-------
 1 file changed, 18 insertions(+), 7 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_dsi.c b/drivers/gpu/drm/i915/intel_dsi.c
index 3ea3839..b397465 100644
--- a/drivers/gpu/drm/i915/intel_dsi.c
+++ b/drivers/gpu/drm/i915/intel_dsi.c
@@ -207,14 +207,9 @@ static void intel_dsi_enable_nop(struct intel_encoder *encoder)
 	 */
 }
 
-static void intel_dsi_disable(struct intel_encoder *encoder)
+static void intel_dsi_pre_disable(struct intel_encoder *encoder)
 {
-	struct drm_device *dev = encoder->base.dev;
-	struct drm_i915_private *dev_priv = dev->dev_private;
-	struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc);
 	struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder->base);
-	int pipe = intel_crtc->pipe;
-	u32 temp;
 
 	DRM_DEBUG_KMS("\n");
 
@@ -222,7 +217,21 @@ static void intel_dsi_disable(struct intel_encoder *encoder)
 		/* Send Shutdown command to the panel in LP mode */
 		dpi_send_cmd(intel_dsi, SHUTDOWN, DPI_LP_MODE_EN);
 		msleep(10);
+	}
+}
 
+static void intel_dsi_disable(struct intel_encoder *encoder)
+{
+	struct drm_device *dev = encoder->base.dev;
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc);
+	struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder->base);
+	int pipe = intel_crtc->pipe;
+	u32 temp;
+
+	DRM_DEBUG_KMS("\n");
+
+	if (is_vid_mode(intel_dsi)) {
 		/* de-assert ip_tg_enable signal */
 		temp = I915_READ(MIPI_PORT_CTRL(pipe));
 		I915_WRITE(MIPI_PORT_CTRL(pipe), temp & ~DPI_ENABLE);
@@ -294,6 +303,8 @@ static void intel_dsi_post_disable(struct intel_encoder *encoder)
 
 	DRM_DEBUG_KMS("\n");
 
+	intel_dsi_disable(encoder);
+
 	intel_dsi_clear_device_ready(encoder);
 
 	val = I915_READ(DSPCLK_GATE_D);
@@ -692,7 +703,7 @@ bool intel_dsi_init(struct drm_device *dev)
 	intel_encoder->pre_pll_enable = intel_dsi_pre_pll_enable;
 	intel_encoder->pre_enable = intel_dsi_pre_enable;
 	intel_encoder->enable = intel_dsi_enable_nop;
-	intel_encoder->disable = intel_dsi_disable;
+	intel_encoder->disable = intel_dsi_pre_disable;
 	intel_encoder->post_disable = intel_dsi_post_disable;
 	intel_encoder->get_hw_state = intel_dsi_get_hw_state;
 	intel_encoder->get_config = intel_dsi_get_config;
-- 
1.8.4