From: Shobhit Kumar <shobhit.kumar@intel.com>
To: intel-gfx <intel-gfx@lists.freedesktop.org>
Cc: Jani Nikula <jani.nikula@intel.com>,
Daniel Vetter <daniel.vetter@intel.com>
Subject: [PATCH 2/3] drm/i915: wait for all DSI FIFOs to be empty
Date: Sat, 12 Jul 2014 17:17:22 +0530 [thread overview]
Message-ID: <1405165643-13189-3-git-send-email-shobhit.kumar@intel.com> (raw)
In-Reply-To: <1405165643-13189-1-git-send-email-shobhit.kumar@intel.com>
Ensure that the DSI packets for a particular sequence are completely
sent before going ahead in the enabling or disabling of the panel
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
---
drivers/gpu/drm/i915/intel_dsi.c | 8 ++++++++
drivers/gpu/drm/i915/intel_dsi_cmd.c | 16 ++++++++++++++++
drivers/gpu/drm/i915/intel_dsi_cmd.h | 1 +
3 files changed, 25 insertions(+)
diff --git a/drivers/gpu/drm/i915/intel_dsi.c b/drivers/gpu/drm/i915/intel_dsi.c
index 61da0e5..98c78ab 100644
--- a/drivers/gpu/drm/i915/intel_dsi.c
+++ b/drivers/gpu/drm/i915/intel_dsi.c
@@ -152,6 +152,8 @@ static void intel_dsi_enable(struct intel_encoder *encoder)
if (intel_dsi->dev.dev_ops->enable)
intel_dsi->dev.dev_ops->enable(&intel_dsi->dev);
+ wait_for_dsi_fifo_empty(intel_dsi);
+
/* assert ip_tg_enable signal */
temp = I915_READ(MIPI_PORT_CTRL(pipe)) & ~LANE_CONFIGURATION_MASK;
temp = temp | intel_dsi->port_bits;
@@ -192,6 +194,8 @@ static void intel_dsi_pre_enable(struct intel_encoder *encoder)
if (intel_dsi->dev.dev_ops->send_otp_cmds)
intel_dsi->dev.dev_ops->send_otp_cmds(&intel_dsi->dev);
+ wait_for_dsi_fifo_empty(intel_dsi);
+
/* Enable port in pre-enable phase itself because as per hw team
* recommendation, port should be enabled befor plane & pipe */
intel_dsi_enable(encoder);
@@ -232,6 +236,8 @@ static void intel_dsi_disable(struct intel_encoder *encoder)
DRM_DEBUG_KMS("\n");
if (is_vid_mode(intel_dsi)) {
+ wait_for_dsi_fifo_empty(intel_dsi);
+
/* de-assert ip_tg_enable signal */
temp = I915_READ(MIPI_PORT_CTRL(pipe));
I915_WRITE(MIPI_PORT_CTRL(pipe), temp & ~DPI_ENABLE);
@@ -261,6 +267,8 @@ static void intel_dsi_disable(struct intel_encoder *encoder)
* some next enable sequence send turn on packet error is observed */
if (intel_dsi->dev.dev_ops->disable)
intel_dsi->dev.dev_ops->disable(&intel_dsi->dev);
+
+ wait_for_dsi_fifo_empty(intel_dsi);
}
static void intel_dsi_clear_device_ready(struct intel_encoder *encoder)
diff --git a/drivers/gpu/drm/i915/intel_dsi_cmd.c b/drivers/gpu/drm/i915/intel_dsi_cmd.c
index 933c863..7f1430a 100644
--- a/drivers/gpu/drm/i915/intel_dsi_cmd.c
+++ b/drivers/gpu/drm/i915/intel_dsi_cmd.c
@@ -419,3 +419,19 @@ int dpi_send_cmd(struct intel_dsi *intel_dsi, u32 cmd, bool hs)
return 0;
}
+
+void wait_for_dsi_fifo_empty(struct intel_dsi *intel_dsi)
+{
+ struct drm_encoder *encoder = &intel_dsi->base.base;
+ struct drm_device *dev = encoder->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(encoder->crtc);
+ enum pipe pipe = intel_crtc->pipe;
+ u32 mask;
+
+ mask = LP_CTRL_FIFO_EMPTY | HS_CTRL_FIFO_EMPTY |
+ LP_DATA_FIFO_EMPTY | HS_DATA_FIFO_EMPTY;
+
+ if (wait_for((I915_READ(MIPI_GEN_FIFO_STAT(pipe)) & mask) == mask, 100))
+ DRM_ERROR("DPI FIFOs are not empty\n");
+}
diff --git a/drivers/gpu/drm/i915/intel_dsi_cmd.h b/drivers/gpu/drm/i915/intel_dsi_cmd.h
index 9a18cbf..46aa1ac 100644
--- a/drivers/gpu/drm/i915/intel_dsi_cmd.h
+++ b/drivers/gpu/drm/i915/intel_dsi_cmd.h
@@ -51,6 +51,7 @@ int dsi_vc_generic_read(struct intel_dsi *intel_dsi, int channel,
u8 *reqdata, int reqlen, u8 *buf, int buflen);
int dpi_send_cmd(struct intel_dsi *intel_dsi, u32 cmd, bool hs);
+void wait_for_dsi_fifo_empty(struct intel_dsi *intel_dsi);
/* XXX: questionable write helpers */
static inline int dsi_vc_dcs_write_0(struct intel_dsi *intel_dsi,
--
1.9.1
next prev parent reply other threads:[~2014-07-12 11:35 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-07-12 11:47 [PATCH 0/3] Fixing last of few known issues in DSI and Burst mode Support Shobhit Kumar
2014-07-12 11:47 ` [PATCH 1/3] drm/i915: Add get_config implementation for DSI encoder Shobhit Kumar
2014-07-12 11:58 ` Daniel Vetter
2014-07-14 14:36 ` Kumar, Shobhit
2014-07-14 15:50 ` Daniel Vetter
2014-07-15 12:24 ` Kumar, Shobhit
2014-07-15 12:45 ` [v2] drm/i915: Add correct hw/sw config check " Shobhit Kumar
2014-07-29 12:22 ` Imre Deak
2014-07-30 15:02 ` [v3] " Shobhit Kumar
2014-07-30 16:24 ` Imre Deak
2014-07-29 11:38 ` [PATCH 1/3] drm/i915: Add get_config implementation " Imre Deak
2014-07-29 11:44 ` Daniel Vetter
2014-07-12 11:47 ` Shobhit Kumar [this message]
2014-07-29 12:30 ` [PATCH 2/3] drm/i915: wait for all DSI FIFOs to be empty Imre Deak
2014-07-12 11:47 ` [PATCH 3/3] drm/i915: Add support for Video Burst Mode for MIPI DSI Shobhit Kumar
2014-07-30 12:22 ` Imre Deak
2014-07-30 15:04 ` [v2] " Shobhit Kumar
2014-07-30 20:36 ` Daniel Vetter
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1405165643-13189-3-git-send-email-shobhit.kumar@intel.com \
--to=shobhit.kumar@intel.com \
--cc=daniel.vetter@intel.com \
--cc=intel-gfx@lists.freedesktop.org \
--cc=jani.nikula@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox