From: Shobhit Kumar <shobhit.kumar@intel.com>
To: intel-gfx <intel-gfx@lists.freedesktop.org>
Cc: Jani Nikula <jani.nikula@intel.com>,
Daniel Vetter <daniel.vetter@intel.com>,
Shobhit Kumar <shobhit.kumar@intel.com>
Subject: [RFC v6 0/8] Crystalcove (CRC) PMIC based panel and pwm control
Date: Fri, 24 Apr 2015 21:03:13 +0530 [thread overview]
Message-ID: <1429889601-13722-1-git-send-email-shobhit.kumar@intel.com> (raw)
Hi All,
Finally I came back to this and tried to address the pending review comments.
Couple of the patches from the older series were merged in linux-next. This
series reworks on the remaining and rebases on linux-next. Basically following
are implemented -
1. GPIO control for panel enable/disable with GFX device as consumer
2. New PWM chip driver added for CRC PMIC based backlight control
3. i915 is modified to use the CRC gpio chip and the CRC PWM chip to do
backlight control. This is now added in intel_panel.c in the generic
panel backlight control infrastructure
All these patches have been tested on AsusT100 and working fine using
/sys/class/backlight/intel_backlight interface.
Recently I noticed another device Dell Venue 8 Pro (BYT-CR) which should be
using LPSS backlight control. There is already a LPSS PWM chip driver in
upstream kernel which should be used in this case. That patch is for another
day.
Regards
Shobhit
Shobhit Kumar (8):
drivers/gpio/gpiolib: Add support for removing registered consumer
lookup table
drivers/pwm/core: Add support to remove registered consumer lookup
tables
drivers/mfd: Add lookup table for Panel Control as GPIO signal
drivers/mfd: Add PWM cell device for Crystalcove PMIC
drivers/mfd: ADD PWM lookup table for CRC PMIC based PWM
drivers/pwm: Add Crystalcove (CRC) PWM driver
drm/i915: Use the CRC gpio for panel enable/disable
drm/i915: Backlight control using CRC PMIC based PWM driver
drivers/gpio/gpiolib.c | 13 +++
drivers/gpu/drm/i915/intel_drv.h | 5 ++
drivers/gpu/drm/i915/intel_dsi.c | 38 ++++++++-
drivers/gpu/drm/i915/intel_dsi.h | 6 ++
drivers/gpu/drm/i915/intel_panel.c | 92 ++++++++++++++++++--
drivers/mfd/intel_soc_pmic_core.c | 29 +++++++
drivers/mfd/intel_soc_pmic_crc.c | 3 +
drivers/pwm/Kconfig | 7 ++
drivers/pwm/Makefile | 1 +
drivers/pwm/core.c | 17 ++++
drivers/pwm/pwm-crc.c | 171 +++++++++++++++++++++++++++++++++++++
include/linux/gpio/machine.h | 1 +
include/linux/pwm.h | 5 ++
13 files changed, 381 insertions(+), 7 deletions(-)
create mode 100644 drivers/pwm/pwm-crc.c
--
2.1.0
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
next reply other threads:[~2015-04-24 15:33 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-04-24 15:33 Shobhit Kumar [this message]
2015-04-24 15:33 ` [RFC v6 1/8] drivers/gpio/gpiolib: Add support for removing registered consumer lookup table Shobhit Kumar
2015-04-24 15:41 ` Shobhit Kumar
2015-04-27 4:03 ` Alexandre Courbot
2015-04-29 12:43 ` Jani Nikula
2015-04-24 15:33 ` [RFC v6 2/8] drivers/pwm/core: Add support to remove registered consumer lookup tables Shobhit Kumar
2015-04-24 15:42 ` Shobhit Kumar
2015-04-24 15:33 ` [RFC v6 3/8] drivers/mfd: Add lookup table for Panel Control as GPIO signal Shobhit Kumar
2015-05-06 13:11 ` Linus Walleij
2015-04-24 15:33 ` [RFC v6 4/8] drivers/mfd: Add PWM cell device for Crystalcove PMIC Shobhit Kumar
2015-04-24 15:33 ` [RFC v6 5/8] drivers/mfd: ADD PWM lookup table for CRC PMIC based PWM Shobhit Kumar
2015-04-24 15:33 ` [RFC v6 6/8] drivers/pwm: Add Crystalcove (CRC) PWM driver Shobhit Kumar
2015-04-24 15:33 ` [RFC v6 7/8] drm/i915: Use the CRC gpio for panel enable/disable Shobhit Kumar
2015-05-06 13:13 ` Linus Walleij
2015-04-24 15:33 ` [RFC v6 8/8] drm/i915: Backlight control using CRC PMIC based PWM driver Shobhit Kumar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1429889601-13722-1-git-send-email-shobhit.kumar@intel.com \
--to=shobhit.kumar@intel.com \
--cc=daniel.vetter@intel.com \
--cc=intel-gfx@lists.freedesktop.org \
--cc=jani.nikula@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox