[PATCH v4 00/10] Unduplicate CHV phy code

[PATCH v4 00/10] Unduplicate CHV phy code

[Ander Conselvan de Oliveira]

Hi,

I checked registre dumps with and without this series and noticed one
difference that was actually intentional but not mentioned, so the
first patch gets an updated commit message.

Also changed chv_phy_post_disable() to chv_phy_post_pll_disable() as
requested by Ville.

Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>

Ander Conselvan de Oliveira (10):
  drm/i915: Set crtc_state->lane_count for HDMI
  drm/i915: Unduplicate CHV signal level code
  drm/i915: Unduplicate chv_data_lane_soft_reset()
  drm/i915: Unduplicate CHV phy-releated pre pll enabling code
  drm/i915: Unduplicate CHV pre-encoder enabling phy logic
  drm/i915: Unduplicate CHV encoders' post pll disable code
  drm/i915: Unduplicate VLV signal level code
  drm/i915: Unduplicate VLV phy pre pll enabling code
  drm/i915: Unduplicate pre encoder enabling phy code
  drm/i915: Move VLV HDMI lane reset work around logic to
    intel_dpio_phy.c

 drivers/gpu/drm/i915/Makefile         |   1 +
 drivers/gpu/drm/i915/i915_drv.h       |  18 ++
 drivers/gpu/drm/i915/intel_ddi.c      |   4 +-
 drivers/gpu/drm/i915/intel_dp.c       | 412 ++---------------------------
 drivers/gpu/drm/i915/intel_dpio_phy.c | 470 ++++++++++++++++++++++++++++++++++
 drivers/gpu/drm/i915/intel_drv.h      |   5 +
 drivers/gpu/drm/i915/intel_hdmi.c     | 356 +------------------------
 7 files changed, 526 insertions(+), 740 deletions(-)
 create mode 100644 drivers/gpu/drm/i915/intel_dpio_phy.c

-- 
2.4.11

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[PATCH v4 01/10] drm/i915: Set crtc_state->lane_count for HDMI

[Ander Conselvan de Oliveira]

Set the lane count for HDMI to 4. This will make it easier to
unduplicate CHV phy code.

This also fixes the the soft reset programming for HDMI with CHV. After
commit a8f327fb8464 ("drm/i915: Clean up CHV lane soft reset
programming"), it wouldn't set the right bits for PCS23 since it relied
on a lane count that was never set.

v2: Set lane_count in *_get_config() to please state checker. (0day)
v3: Set lane_count for DDI in DVI mode too. (CI)
v4: Add note about CHV soft lane reset. (Ander)

Fixes: a8f327fb8464 ("drm/i915: Clean up CHV lane soft reset programming")
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
---
 drivers/gpu/drm/i915/intel_ddi.c  | 4 +++-
 drivers/gpu/drm/i915/intel_hdmi.c | 4 ++++
 2 files changed, 7 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
index e30e178..422ec81 100644
--- a/drivers/gpu/drm/i915/intel_ddi.c
+++ b/drivers/gpu/drm/i915/intel_ddi.c
@@ -2197,8 +2197,10 @@ void intel_ddi_get_config(struct intel_encoder *encoder,
 
 		if (intel_hdmi->infoframe_enabled(&encoder->base, pipe_config))
 			pipe_config->has_infoframe = true;
-		break;
+		/* fall through */
 	case TRANS_DDI_MODE_SELECT_DVI:
+		pipe_config->lane_count = 4;
+		break;
 	case TRANS_DDI_MODE_SELECT_FDI:
 		break;
 	case TRANS_DDI_MODE_SELECT_DP_SST:
diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c
index 2cdab73..718eba2 100644
--- a/drivers/gpu/drm/i915/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/intel_hdmi.c
@@ -953,6 +953,8 @@ static void intel_hdmi_get_config(struct intel_encoder *encoder,
 		dotclock /= pipe_config->pixel_multiplier;
 
 	pipe_config->base.adjusted_mode.crtc_clock = dotclock;
+
+	pipe_config->lane_count = 4;
 }
 
 static void intel_enable_hdmi_audio(struct intel_encoder *encoder)
@@ -1337,6 +1339,8 @@ bool intel_hdmi_compute_config(struct intel_encoder *encoder,
 	/* Set user selected PAR to incoming mode's member */
 	adjusted_mode->picture_aspect_ratio = intel_hdmi->aspect_ratio;
 
+	pipe_config->lane_count = 4;
+
 	return true;
 }
 
-- 
2.4.11

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[PATCH v4 02/10] drm/i915: Unduplicate CHV signal level code

[Ander Conselvan de Oliveira]

The code for programming voltage swing and emphasis was duplicated
between DP and HDMI code. Move that to a new file, intel_dpio_phy.c.

v2: Keep the "Use 800mV-0dB" comment in the HDMI code. (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
---
 drivers/gpu/drm/i915/Makefile         |   1 +
 drivers/gpu/drm/i915/i915_drv.h       |   5 ++
 drivers/gpu/drm/i915/intel_dp.c       | 103 ++--------------------------
 drivers/gpu/drm/i915/intel_dpio_phy.c | 122 ++++++++++++++++++++++++++++++++++
 drivers/gpu/drm/i915/intel_hdmi.c     |  70 +------------------
 5 files changed, 136 insertions(+), 165 deletions(-)
 create mode 100644 drivers/gpu/drm/i915/intel_dpio_phy.c

diff --git a/drivers/gpu/drm/i915/Makefile b/drivers/gpu/drm/i915/Makefile
index 723c502..63c4d2b 100644
--- a/drivers/gpu/drm/i915/Makefile
+++ b/drivers/gpu/drm/i915/Makefile
@@ -59,6 +59,7 @@ i915-y += intel_audio.o \
 	  intel_bios.o \
 	  intel_color.o \
 	  intel_display.o \
+	  intel_dpio_phy.o \
 	  intel_dpll_mgr.o \
 	  intel_fbc.o \
 	  intel_fifo_underrun.o \
diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
index 32f0597..9760b42 100644
--- a/drivers/gpu/drm/i915/i915_drv.h
+++ b/drivers/gpu/drm/i915/i915_drv.h
@@ -3577,6 +3577,11 @@ void intel_sbi_write(struct drm_i915_private *dev_priv, u16 reg, u32 value,
 u32 vlv_flisdsi_read(struct drm_i915_private *dev_priv, u32 reg);
 void vlv_flisdsi_write(struct drm_i915_private *dev_priv, u32 reg, u32 val);
 
+/* intel_dpio_phy.c */
+void chv_set_phy_signal_level(struct intel_encoder *encoder,
+			      u32 deemph_reg_value, u32 margin_reg_value,
+			      bool uniq_trans_scale);
+
 int intel_gpu_freq(struct drm_i915_private *dev_priv, int val);
 int intel_freq_opcode(struct drm_i915_private *dev_priv, int val);
 
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index c12c414..bdafd72 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -3276,23 +3276,12 @@ static uint32_t vlv_signal_levels(struct intel_dp *intel_dp)
 	return 0;
 }
 
-static bool chv_need_uniq_trans_scale(uint8_t train_set)
-{
-	return (train_set & DP_TRAIN_PRE_EMPHASIS_MASK) == DP_TRAIN_PRE_EMPH_LEVEL_0 &&
-		(train_set & DP_TRAIN_VOLTAGE_SWING_MASK) == DP_TRAIN_VOLTAGE_SWING_LEVEL_3;
-}
-
 static uint32_t chv_signal_levels(struct intel_dp *intel_dp)
 {
-	struct drm_device *dev = intel_dp_to_dev(intel_dp);
-	struct drm_i915_private *dev_priv = dev->dev_private;
-	struct intel_digital_port *dport = dp_to_dig_port(intel_dp);
-	struct intel_crtc *intel_crtc = to_intel_crtc(dport->base.base.crtc);
-	u32 deemph_reg_value, margin_reg_value, val;
+	struct intel_encoder *encoder = &dp_to_dig_port(intel_dp)->base;
+	u32 deemph_reg_value, margin_reg_value;
+	bool uniq_trans_scale = false;
 	uint8_t train_set = intel_dp->train_set[0];
-	enum dpio_channel ch = vlv_dport_to_channel(dport);
-	enum pipe pipe = intel_crtc->pipe;
-	int i;
 
 	switch (train_set & DP_TRAIN_PRE_EMPHASIS_MASK) {
 	case DP_TRAIN_PRE_EMPH_LEVEL_0:
@@ -3312,7 +3301,7 @@ static uint32_t chv_signal_levels(struct intel_dp *intel_dp)
 		case DP_TRAIN_VOLTAGE_SWING_LEVEL_3:
 			deemph_reg_value = 128;
 			margin_reg_value = 154;
-			/* FIXME extra to set for 1200 */
+			uniq_trans_scale = true;
 			break;
 		default:
 			return 0;
@@ -3364,88 +3353,8 @@ static uint32_t chv_signal_levels(struct intel_dp *intel_dp)
 		return 0;
 	}
 
-	mutex_lock(&dev_priv->sb_lock);
-
-	/* Clear calc init */
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW10(ch));
-	val &= ~(DPIO_PCS_SWING_CALC_TX0_TX2 | DPIO_PCS_SWING_CALC_TX1_TX3);
-	val &= ~(DPIO_PCS_TX1DEEMP_MASK | DPIO_PCS_TX2DEEMP_MASK);
-	val |= DPIO_PCS_TX1DEEMP_9P5 | DPIO_PCS_TX2DEEMP_9P5;
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW10(ch), val);
-
-	if (intel_crtc->config->lane_count > 2) {
-		val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW10(ch));
-		val &= ~(DPIO_PCS_SWING_CALC_TX0_TX2 | DPIO_PCS_SWING_CALC_TX1_TX3);
-		val &= ~(DPIO_PCS_TX1DEEMP_MASK | DPIO_PCS_TX2DEEMP_MASK);
-		val |= DPIO_PCS_TX1DEEMP_9P5 | DPIO_PCS_TX2DEEMP_9P5;
-		vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW10(ch), val);
-	}
-
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW9(ch));
-	val &= ~(DPIO_PCS_TX1MARGIN_MASK | DPIO_PCS_TX2MARGIN_MASK);
-	val |= DPIO_PCS_TX1MARGIN_000 | DPIO_PCS_TX2MARGIN_000;
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW9(ch), val);
-
-	if (intel_crtc->config->lane_count > 2) {
-		val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW9(ch));
-		val &= ~(DPIO_PCS_TX1MARGIN_MASK | DPIO_PCS_TX2MARGIN_MASK);
-		val |= DPIO_PCS_TX1MARGIN_000 | DPIO_PCS_TX2MARGIN_000;
-		vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW9(ch), val);
-	}
-
-	/* Program swing deemph */
-	for (i = 0; i < intel_crtc->config->lane_count; i++) {
-		val = vlv_dpio_read(dev_priv, pipe, CHV_TX_DW4(ch, i));
-		val &= ~DPIO_SWING_DEEMPH9P5_MASK;
-		val |= deemph_reg_value << DPIO_SWING_DEEMPH9P5_SHIFT;
-		vlv_dpio_write(dev_priv, pipe, CHV_TX_DW4(ch, i), val);
-	}
-
-	/* Program swing margin */
-	for (i = 0; i < intel_crtc->config->lane_count; i++) {
-		val = vlv_dpio_read(dev_priv, pipe, CHV_TX_DW2(ch, i));
-
-		val &= ~DPIO_SWING_MARGIN000_MASK;
-		val |= margin_reg_value << DPIO_SWING_MARGIN000_SHIFT;
-
-		/*
-		 * Supposedly this value shouldn't matter when unique transition
-		 * scale is disabled, but in fact it does matter. Let's just
-		 * always program the same value and hope it's OK.
-		 */
-		val &= ~(0xff << DPIO_UNIQ_TRANS_SCALE_SHIFT);
-		val |= 0x9a << DPIO_UNIQ_TRANS_SCALE_SHIFT;
-
-		vlv_dpio_write(dev_priv, pipe, CHV_TX_DW2(ch, i), val);
-	}
-
-	/*
-	 * The document said it needs to set bit 27 for ch0 and bit 26
-	 * for ch1. Might be a typo in the doc.
-	 * For now, for this unique transition scale selection, set bit
-	 * 27 for ch0 and ch1.
-	 */
-	for (i = 0; i < intel_crtc->config->lane_count; i++) {
-		val = vlv_dpio_read(dev_priv, pipe, CHV_TX_DW3(ch, i));
-		if (chv_need_uniq_trans_scale(train_set))
-			val |= DPIO_TX_UNIQ_TRANS_SCALE_EN;
-		else
-			val &= ~DPIO_TX_UNIQ_TRANS_SCALE_EN;
-		vlv_dpio_write(dev_priv, pipe, CHV_TX_DW3(ch, i), val);
-	}
-
-	/* Start swing calculation */
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW10(ch));
-	val |= DPIO_PCS_SWING_CALC_TX0_TX2 | DPIO_PCS_SWING_CALC_TX1_TX3;
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW10(ch), val);
-
-	if (intel_crtc->config->lane_count > 2) {
-		val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW10(ch));
-		val |= DPIO_PCS_SWING_CALC_TX0_TX2 | DPIO_PCS_SWING_CALC_TX1_TX3;
-		vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW10(ch), val);
-	}
-
-	mutex_unlock(&dev_priv->sb_lock);
+	chv_set_phy_signal_level(encoder, deemph_reg_value,
+				 margin_reg_value, uniq_trans_scale);
 
 	return 0;
 }
diff --git a/drivers/gpu/drm/i915/intel_dpio_phy.c b/drivers/gpu/drm/i915/intel_dpio_phy.c
new file mode 100644
index 0000000..cbe1703d
--- /dev/null
+++ b/drivers/gpu/drm/i915/intel_dpio_phy.c
@@ -0,0 +1,122 @@
+/*
+ * Copyright © 2014-2016 Intel Corporation
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice (including the next
+ * paragraph) shall be included in all copies or substantial portions of the
+ * Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
+ * DEALINGS IN THE SOFTWARE.
+ */
+
+#include "intel_drv.h"
+
+void chv_set_phy_signal_level(struct intel_encoder *encoder,
+			      u32 deemph_reg_value, u32 margin_reg_value,
+			      bool uniq_trans_scale)
+{
+	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
+	struct intel_digital_port *dport = enc_to_dig_port(&encoder->base);
+	struct intel_crtc *intel_crtc = to_intel_crtc(dport->base.base.crtc);
+	enum dpio_channel ch = vlv_dport_to_channel(dport);
+	enum pipe pipe = intel_crtc->pipe;
+	u32 val;
+	int i;
+
+	mutex_lock(&dev_priv->sb_lock);
+
+	/* Clear calc init */
+	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW10(ch));
+	val &= ~(DPIO_PCS_SWING_CALC_TX0_TX2 | DPIO_PCS_SWING_CALC_TX1_TX3);
+	val &= ~(DPIO_PCS_TX1DEEMP_MASK | DPIO_PCS_TX2DEEMP_MASK);
+	val |= DPIO_PCS_TX1DEEMP_9P5 | DPIO_PCS_TX2DEEMP_9P5;
+	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW10(ch), val);
+
+	if (intel_crtc->config->lane_count > 2) {
+		val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW10(ch));
+		val &= ~(DPIO_PCS_SWING_CALC_TX0_TX2 | DPIO_PCS_SWING_CALC_TX1_TX3);
+		val &= ~(DPIO_PCS_TX1DEEMP_MASK | DPIO_PCS_TX2DEEMP_MASK);
+		val |= DPIO_PCS_TX1DEEMP_9P5 | DPIO_PCS_TX2DEEMP_9P5;
+		vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW10(ch), val);
+	}
+
+	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW9(ch));
+	val &= ~(DPIO_PCS_TX1MARGIN_MASK | DPIO_PCS_TX2MARGIN_MASK);
+	val |= DPIO_PCS_TX1MARGIN_000 | DPIO_PCS_TX2MARGIN_000;
+	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW9(ch), val);
+
+	if (intel_crtc->config->lane_count > 2) {
+		val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW9(ch));
+		val &= ~(DPIO_PCS_TX1MARGIN_MASK | DPIO_PCS_TX2MARGIN_MASK);
+		val |= DPIO_PCS_TX1MARGIN_000 | DPIO_PCS_TX2MARGIN_000;
+		vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW9(ch), val);
+	}
+
+	/* Program swing deemph */
+	for (i = 0; i < intel_crtc->config->lane_count; i++) {
+		val = vlv_dpio_read(dev_priv, pipe, CHV_TX_DW4(ch, i));
+		val &= ~DPIO_SWING_DEEMPH9P5_MASK;
+		val |= deemph_reg_value << DPIO_SWING_DEEMPH9P5_SHIFT;
+		vlv_dpio_write(dev_priv, pipe, CHV_TX_DW4(ch, i), val);
+	}
+
+	/* Program swing margin */
+	for (i = 0; i < intel_crtc->config->lane_count; i++) {
+		val = vlv_dpio_read(dev_priv, pipe, CHV_TX_DW2(ch, i));
+
+		val &= ~DPIO_SWING_MARGIN000_MASK;
+		val |= margin_reg_value << DPIO_SWING_MARGIN000_SHIFT;
+
+		/*
+		 * Supposedly this value shouldn't matter when unique transition
+		 * scale is disabled, but in fact it does matter. Let's just
+		 * always program the same value and hope it's OK.
+		 */
+		val &= ~(0xff << DPIO_UNIQ_TRANS_SCALE_SHIFT);
+		val |= 0x9a << DPIO_UNIQ_TRANS_SCALE_SHIFT;
+
+		vlv_dpio_write(dev_priv, pipe, CHV_TX_DW2(ch, i), val);
+	}
+
+	/*
+	 * The document said it needs to set bit 27 for ch0 and bit 26
+	 * for ch1. Might be a typo in the doc.
+	 * For now, for this unique transition scale selection, set bit
+	 * 27 for ch0 and ch1.
+	 */
+	for (i = 0; i < intel_crtc->config->lane_count; i++) {
+		val = vlv_dpio_read(dev_priv, pipe, CHV_TX_DW3(ch, i));
+		if (uniq_trans_scale)
+			val |= DPIO_TX_UNIQ_TRANS_SCALE_EN;
+		else
+			val &= ~DPIO_TX_UNIQ_TRANS_SCALE_EN;
+		vlv_dpio_write(dev_priv, pipe, CHV_TX_DW3(ch, i), val);
+	}
+
+	/* Start swing calculation */
+	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW10(ch));
+	val |= DPIO_PCS_SWING_CALC_TX0_TX2 | DPIO_PCS_SWING_CALC_TX1_TX3;
+	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW10(ch), val);
+
+	if (intel_crtc->config->lane_count > 2) {
+		val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW10(ch));
+		val |= DPIO_PCS_SWING_CALC_TX0_TX2 | DPIO_PCS_SWING_CALC_TX1_TX3;
+		vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW10(ch), val);
+	}
+
+	mutex_unlock(&dev_priv->sb_lock);
+
+}
+
diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c
index 718eba2..494e02e 100644
--- a/drivers/gpu/drm/i915/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/intel_hdmi.c
@@ -1921,77 +1921,11 @@ static void chv_hdmi_pre_enable(struct intel_encoder *encoder)
 	/* Deassert data lane reset */
 	chv_data_lane_soft_reset(encoder, false);
 
-	/* Clear calc init */
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW10(ch));
-	val &= ~(DPIO_PCS_SWING_CALC_TX0_TX2 | DPIO_PCS_SWING_CALC_TX1_TX3);
-	val &= ~(DPIO_PCS_TX1DEEMP_MASK | DPIO_PCS_TX2DEEMP_MASK);
-	val |= DPIO_PCS_TX1DEEMP_9P5 | DPIO_PCS_TX2DEEMP_9P5;
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW10(ch), val);
-
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW10(ch));
-	val &= ~(DPIO_PCS_SWING_CALC_TX0_TX2 | DPIO_PCS_SWING_CALC_TX1_TX3);
-	val &= ~(DPIO_PCS_TX1DEEMP_MASK | DPIO_PCS_TX2DEEMP_MASK);
-	val |= DPIO_PCS_TX1DEEMP_9P5 | DPIO_PCS_TX2DEEMP_9P5;
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW10(ch), val);
-
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW9(ch));
-	val &= ~(DPIO_PCS_TX1MARGIN_MASK | DPIO_PCS_TX2MARGIN_MASK);
-	val |= DPIO_PCS_TX1MARGIN_000 | DPIO_PCS_TX2MARGIN_000;
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW9(ch), val);
-
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW9(ch));
-	val &= ~(DPIO_PCS_TX1MARGIN_MASK | DPIO_PCS_TX2MARGIN_MASK);
-	val |= DPIO_PCS_TX1MARGIN_000 | DPIO_PCS_TX2MARGIN_000;
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW9(ch), val);
+	mutex_unlock(&dev_priv->sb_lock);
 
 	/* FIXME: Program the support xxx V-dB */
 	/* Use 800mV-0dB */
-	for (i = 0; i < 4; i++) {
-		val = vlv_dpio_read(dev_priv, pipe, CHV_TX_DW4(ch, i));
-		val &= ~DPIO_SWING_DEEMPH9P5_MASK;
-		val |= 128 << DPIO_SWING_DEEMPH9P5_SHIFT;
-		vlv_dpio_write(dev_priv, pipe, CHV_TX_DW4(ch, i), val);
-	}
-
-	for (i = 0; i < 4; i++) {
-		val = vlv_dpio_read(dev_priv, pipe, CHV_TX_DW2(ch, i));
-
-		val &= ~DPIO_SWING_MARGIN000_MASK;
-		val |= 102 << DPIO_SWING_MARGIN000_SHIFT;
-
-		/*
-		 * Supposedly this value shouldn't matter when unique transition
-		 * scale is disabled, but in fact it does matter. Let's just
-		 * always program the same value and hope it's OK.
-		 */
-		val &= ~(0xff << DPIO_UNIQ_TRANS_SCALE_SHIFT);
-		val |= 0x9a << DPIO_UNIQ_TRANS_SCALE_SHIFT;
-
-		vlv_dpio_write(dev_priv, pipe, CHV_TX_DW2(ch, i), val);
-	}
-
-	/*
-	 * The document said it needs to set bit 27 for ch0 and bit 26
-	 * for ch1. Might be a typo in the doc.
-	 * For now, for this unique transition scale selection, set bit
-	 * 27 for ch0 and ch1.
-	 */
-	for (i = 0; i < 4; i++) {
-		val = vlv_dpio_read(dev_priv, pipe, CHV_TX_DW3(ch, i));
-		val &= ~DPIO_TX_UNIQ_TRANS_SCALE_EN;
-		vlv_dpio_write(dev_priv, pipe, CHV_TX_DW3(ch, i), val);
-	}
-
-	/* Start swing calculation */
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW10(ch));
-	val |= DPIO_PCS_SWING_CALC_TX0_TX2 | DPIO_PCS_SWING_CALC_TX1_TX3;
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW10(ch), val);
-
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW10(ch));
-	val |= DPIO_PCS_SWING_CALC_TX0_TX2 | DPIO_PCS_SWING_CALC_TX1_TX3;
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW10(ch), val);
-
-	mutex_unlock(&dev_priv->sb_lock);
+	chv_set_phy_signal_level(encoder, 128, 102, false);
 
 	intel_hdmi->set_infoframes(&encoder->base,
 				   intel_crtc->config->has_hdmi_sink,
-- 
2.4.11

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[PATCH v4 03/10] drm/i915: Unduplicate chv_data_lane_soft_reset()

[Ander Conselvan de Oliveira]

The function chv_data_lane_soft_reset() was duplicated in DP and HDMI
code. Move it to intel_dpio_phy.c.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
---
 drivers/gpu/drm/i915/i915_drv.h       |  2 ++
 drivers/gpu/drm/i915/intel_dp.c       | 44 -----------------------------------
 drivers/gpu/drm/i915/intel_dpio_phy.c | 43 ++++++++++++++++++++++++++++++++++
 drivers/gpu/drm/i915/intel_hdmi.c     | 44 -----------------------------------
 4 files changed, 45 insertions(+), 88 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
index 9760b42..7309d3f 100644
--- a/drivers/gpu/drm/i915/i915_drv.h
+++ b/drivers/gpu/drm/i915/i915_drv.h
@@ -3581,6 +3581,8 @@ void vlv_flisdsi_write(struct drm_i915_private *dev_priv, u32 reg, u32 val);
 void chv_set_phy_signal_level(struct intel_encoder *encoder,
 			      u32 deemph_reg_value, u32 margin_reg_value,
 			      bool uniq_trans_scale);
+void chv_data_lane_soft_reset(struct intel_encoder *encoder,
+			      bool reset);
 
 int intel_gpu_freq(struct drm_i915_private *dev_priv, int val);
 int intel_freq_opcode(struct drm_i915_private *dev_priv, int val);
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index bdafd72..3a411de 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -2460,50 +2460,6 @@ static void vlv_post_disable_dp(struct intel_encoder *encoder)
 	intel_dp_link_down(intel_dp);
 }
 
-static void chv_data_lane_soft_reset(struct intel_encoder *encoder,
-				     bool reset)
-{
-	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
-	enum dpio_channel ch = vlv_dport_to_channel(enc_to_dig_port(&encoder->base));
-	struct intel_crtc *crtc = to_intel_crtc(encoder->base.crtc);
-	enum pipe pipe = crtc->pipe;
-	uint32_t val;
-
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW0(ch));
-	if (reset)
-		val &= ~(DPIO_PCS_TX_LANE2_RESET | DPIO_PCS_TX_LANE1_RESET);
-	else
-		val |= DPIO_PCS_TX_LANE2_RESET | DPIO_PCS_TX_LANE1_RESET;
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW0(ch), val);
-
-	if (crtc->config->lane_count > 2) {
-		val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW0(ch));
-		if (reset)
-			val &= ~(DPIO_PCS_TX_LANE2_RESET | DPIO_PCS_TX_LANE1_RESET);
-		else
-			val |= DPIO_PCS_TX_LANE2_RESET | DPIO_PCS_TX_LANE1_RESET;
-		vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW0(ch), val);
-	}
-
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW1(ch));
-	val |= CHV_PCS_REQ_SOFTRESET_EN;
-	if (reset)
-		val &= ~DPIO_PCS_CLK_SOFT_RESET;
-	else
-		val |= DPIO_PCS_CLK_SOFT_RESET;
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW1(ch), val);
-
-	if (crtc->config->lane_count > 2) {
-		val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW1(ch));
-		val |= CHV_PCS_REQ_SOFTRESET_EN;
-		if (reset)
-			val &= ~DPIO_PCS_CLK_SOFT_RESET;
-		else
-			val |= DPIO_PCS_CLK_SOFT_RESET;
-		vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW1(ch), val);
-	}
-}
-
 static void chv_post_disable_dp(struct intel_encoder *encoder)
 {
 	struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
diff --git a/drivers/gpu/drm/i915/intel_dpio_phy.c b/drivers/gpu/drm/i915/intel_dpio_phy.c
index cbe1703d..9854c93 100644
--- a/drivers/gpu/drm/i915/intel_dpio_phy.c
+++ b/drivers/gpu/drm/i915/intel_dpio_phy.c
@@ -120,3 +120,46 @@ void chv_set_phy_signal_level(struct intel_encoder *encoder,
 
 }
 
+void chv_data_lane_soft_reset(struct intel_encoder *encoder,
+			      bool reset)
+{
+	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
+	enum dpio_channel ch = vlv_dport_to_channel(enc_to_dig_port(&encoder->base));
+	struct intel_crtc *crtc = to_intel_crtc(encoder->base.crtc);
+	enum pipe pipe = crtc->pipe;
+	uint32_t val;
+
+	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW0(ch));
+	if (reset)
+		val &= ~(DPIO_PCS_TX_LANE2_RESET | DPIO_PCS_TX_LANE1_RESET);
+	else
+		val |= DPIO_PCS_TX_LANE2_RESET | DPIO_PCS_TX_LANE1_RESET;
+	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW0(ch), val);
+
+	if (crtc->config->lane_count > 2) {
+		val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW0(ch));
+		if (reset)
+			val &= ~(DPIO_PCS_TX_LANE2_RESET | DPIO_PCS_TX_LANE1_RESET);
+		else
+			val |= DPIO_PCS_TX_LANE2_RESET | DPIO_PCS_TX_LANE1_RESET;
+		vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW0(ch), val);
+	}
+
+	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW1(ch));
+	val |= CHV_PCS_REQ_SOFTRESET_EN;
+	if (reset)
+		val &= ~DPIO_PCS_CLK_SOFT_RESET;
+	else
+		val |= DPIO_PCS_CLK_SOFT_RESET;
+	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW1(ch), val);
+
+	if (crtc->config->lane_count > 2) {
+		val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW1(ch));
+		val |= CHV_PCS_REQ_SOFTRESET_EN;
+		if (reset)
+			val &= ~DPIO_PCS_CLK_SOFT_RESET;
+		else
+			val |= DPIO_PCS_CLK_SOFT_RESET;
+		vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW1(ch), val);
+	}
+}
diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c
index 494e02e..2d429d0 100644
--- a/drivers/gpu/drm/i915/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/intel_hdmi.c
@@ -1666,50 +1666,6 @@ static void vlv_hdmi_pre_pll_enable(struct intel_encoder *encoder)
 	mutex_unlock(&dev_priv->sb_lock);
 }
 
-static void chv_data_lane_soft_reset(struct intel_encoder *encoder,
-				     bool reset)
-{
-	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
-	enum dpio_channel ch = vlv_dport_to_channel(enc_to_dig_port(&encoder->base));
-	struct intel_crtc *crtc = to_intel_crtc(encoder->base.crtc);
-	enum pipe pipe = crtc->pipe;
-	uint32_t val;
-
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW0(ch));
-	if (reset)
-		val &= ~(DPIO_PCS_TX_LANE2_RESET | DPIO_PCS_TX_LANE1_RESET);
-	else
-		val |= DPIO_PCS_TX_LANE2_RESET | DPIO_PCS_TX_LANE1_RESET;
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW0(ch), val);
-
-	if (crtc->config->lane_count > 2) {
-		val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW0(ch));
-		if (reset)
-			val &= ~(DPIO_PCS_TX_LANE2_RESET | DPIO_PCS_TX_LANE1_RESET);
-		else
-			val |= DPIO_PCS_TX_LANE2_RESET | DPIO_PCS_TX_LANE1_RESET;
-		vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW0(ch), val);
-	}
-
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW1(ch));
-	val |= CHV_PCS_REQ_SOFTRESET_EN;
-	if (reset)
-		val &= ~DPIO_PCS_CLK_SOFT_RESET;
-	else
-		val |= DPIO_PCS_CLK_SOFT_RESET;
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW1(ch), val);
-
-	if (crtc->config->lane_count > 2) {
-		val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW1(ch));
-		val |= CHV_PCS_REQ_SOFTRESET_EN;
-		if (reset)
-			val &= ~DPIO_PCS_CLK_SOFT_RESET;
-		else
-			val |= DPIO_PCS_CLK_SOFT_RESET;
-		vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW1(ch), val);
-	}
-}
-
 static void chv_hdmi_pre_pll_enable(struct intel_encoder *encoder)
 {
 	struct intel_digital_port *dport = enc_to_dig_port(&encoder->base);
-- 
2.4.11

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[PATCH v4 04/10] drm/i915: Unduplicate CHV phy-releated pre pll enabling code

[Ander Conselvan de Oliveira]

The same logic is used for DP and HDMI so move it to intel_dpio_phy.c.

v2: Rebase

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
---
 drivers/gpu/drm/i915/i915_drv.h       |  1 +
 drivers/gpu/drm/i915/intel_dp.c       | 83 +----------------------------------
 drivers/gpu/drm/i915/intel_dpio_phy.c | 81 ++++++++++++++++++++++++++++++++++
 drivers/gpu/drm/i915/intel_drv.h      |  5 +++
 drivers/gpu/drm/i915/intel_hdmi.c     | 74 +------------------------------
 5 files changed, 89 insertions(+), 155 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
index 7309d3f..4e34d3d 100644
--- a/drivers/gpu/drm/i915/i915_drv.h
+++ b/drivers/gpu/drm/i915/i915_drv.h
@@ -3583,6 +3583,7 @@ void chv_set_phy_signal_level(struct intel_encoder *encoder,
 			      bool uniq_trans_scale);
 void chv_data_lane_soft_reset(struct intel_encoder *encoder,
 			      bool reset);
+void chv_phy_pre_pll_enable(struct intel_encoder *encoder);
 
 int intel_gpu_freq(struct drm_i915_private *dev_priv, int val);
 int intel_freq_opcode(struct drm_i915_private *dev_priv, int val);
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index 3a411de..1f6fd89 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -131,11 +131,6 @@ static void vlv_steal_power_sequencer(struct drm_device *dev,
 				      enum pipe pipe);
 static void intel_dp_unset_edid(struct intel_dp *intel_dp);
 
-static unsigned int intel_dp_unused_lane_mask(int lane_count)
-{
-	return ~((1 << lane_count) - 1) & 0xf;
-}
-
 static int
 intel_dp_max_link_bw(struct intel_dp  *intel_dp)
 {
@@ -2915,85 +2910,9 @@ static void chv_pre_enable_dp(struct intel_encoder *encoder)
 
 static void chv_dp_pre_pll_enable(struct intel_encoder *encoder)
 {
-	struct intel_digital_port *dport = enc_to_dig_port(&encoder->base);
-	struct drm_device *dev = encoder->base.dev;
-	struct drm_i915_private *dev_priv = dev->dev_private;
-	struct intel_crtc *intel_crtc =
-		to_intel_crtc(encoder->base.crtc);
-	enum dpio_channel ch = vlv_dport_to_channel(dport);
-	enum pipe pipe = intel_crtc->pipe;
-	unsigned int lane_mask =
-		intel_dp_unused_lane_mask(intel_crtc->config->lane_count);
-	u32 val;
-
 	intel_dp_prepare(encoder);
 
-	/*
-	 * Must trick the second common lane into life.
-	 * Otherwise we can't even access the PLL.
-	 */
-	if (ch == DPIO_CH0 && pipe == PIPE_B)
-		dport->release_cl2_override =
-			!chv_phy_powergate_ch(dev_priv, DPIO_PHY0, DPIO_CH1, true);
-
-	chv_phy_powergate_lanes(encoder, true, lane_mask);
-
-	mutex_lock(&dev_priv->sb_lock);
-
-	/* Assert data lane reset */
-	chv_data_lane_soft_reset(encoder, true);
-
-	/* program left/right clock distribution */
-	if (pipe != PIPE_B) {
-		val = vlv_dpio_read(dev_priv, pipe, _CHV_CMN_DW5_CH0);
-		val &= ~(CHV_BUFLEFTENA1_MASK | CHV_BUFRIGHTENA1_MASK);
-		if (ch == DPIO_CH0)
-			val |= CHV_BUFLEFTENA1_FORCE;
-		if (ch == DPIO_CH1)
-			val |= CHV_BUFRIGHTENA1_FORCE;
-		vlv_dpio_write(dev_priv, pipe, _CHV_CMN_DW5_CH0, val);
-	} else {
-		val = vlv_dpio_read(dev_priv, pipe, _CHV_CMN_DW1_CH1);
-		val &= ~(CHV_BUFLEFTENA2_MASK | CHV_BUFRIGHTENA2_MASK);
-		if (ch == DPIO_CH0)
-			val |= CHV_BUFLEFTENA2_FORCE;
-		if (ch == DPIO_CH1)
-			val |= CHV_BUFRIGHTENA2_FORCE;
-		vlv_dpio_write(dev_priv, pipe, _CHV_CMN_DW1_CH1, val);
-	}
-
-	/* program clock channel usage */
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW8(ch));
-	val |= CHV_PCS_USEDCLKCHANNEL_OVRRIDE;
-	if (pipe != PIPE_B)
-		val &= ~CHV_PCS_USEDCLKCHANNEL;
-	else
-		val |= CHV_PCS_USEDCLKCHANNEL;
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW8(ch), val);
-
-	if (intel_crtc->config->lane_count > 2) {
-		val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW8(ch));
-		val |= CHV_PCS_USEDCLKCHANNEL_OVRRIDE;
-		if (pipe != PIPE_B)
-			val &= ~CHV_PCS_USEDCLKCHANNEL;
-		else
-			val |= CHV_PCS_USEDCLKCHANNEL;
-		vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW8(ch), val);
-	}
-
-	/*
-	 * This a a bit weird since generally CL
-	 * matches the pipe, but here we need to
-	 * pick the CL based on the port.
-	 */
-	val = vlv_dpio_read(dev_priv, pipe, CHV_CMN_DW19(ch));
-	if (pipe != PIPE_B)
-		val &= ~CHV_CMN_USEDCLKCHANNEL;
-	else
-		val |= CHV_CMN_USEDCLKCHANNEL;
-	vlv_dpio_write(dev_priv, pipe, CHV_CMN_DW19(ch), val);
-
-	mutex_unlock(&dev_priv->sb_lock);
+	chv_phy_pre_pll_enable(encoder);
 }
 
 static void chv_dp_post_pll_disable(struct intel_encoder *encoder)
diff --git a/drivers/gpu/drm/i915/intel_dpio_phy.c b/drivers/gpu/drm/i915/intel_dpio_phy.c
index 9854c93..b4ca3ff 100644
--- a/drivers/gpu/drm/i915/intel_dpio_phy.c
+++ b/drivers/gpu/drm/i915/intel_dpio_phy.c
@@ -163,3 +163,84 @@ void chv_data_lane_soft_reset(struct intel_encoder *encoder,
 		vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW1(ch), val);
 	}
 }
+
+void chv_phy_pre_pll_enable(struct intel_encoder *encoder)
+{
+	struct intel_digital_port *dport = enc_to_dig_port(&encoder->base);
+	struct drm_device *dev = encoder->base.dev;
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	struct intel_crtc *intel_crtc =
+		to_intel_crtc(encoder->base.crtc);
+	enum dpio_channel ch = vlv_dport_to_channel(dport);
+	enum pipe pipe = intel_crtc->pipe;
+	unsigned int lane_mask =
+		intel_dp_unused_lane_mask(intel_crtc->config->lane_count);
+	u32 val;
+
+	/*
+	 * Must trick the second common lane into life.
+	 * Otherwise we can't even access the PLL.
+	 */
+	if (ch == DPIO_CH0 && pipe == PIPE_B)
+		dport->release_cl2_override =
+			!chv_phy_powergate_ch(dev_priv, DPIO_PHY0, DPIO_CH1, true);
+
+	chv_phy_powergate_lanes(encoder, true, lane_mask);
+
+	mutex_lock(&dev_priv->sb_lock);
+
+	/* Assert data lane reset */
+	chv_data_lane_soft_reset(encoder, true);
+
+	/* program left/right clock distribution */
+	if (pipe != PIPE_B) {
+		val = vlv_dpio_read(dev_priv, pipe, _CHV_CMN_DW5_CH0);
+		val &= ~(CHV_BUFLEFTENA1_MASK | CHV_BUFRIGHTENA1_MASK);
+		if (ch == DPIO_CH0)
+			val |= CHV_BUFLEFTENA1_FORCE;
+		if (ch == DPIO_CH1)
+			val |= CHV_BUFRIGHTENA1_FORCE;
+		vlv_dpio_write(dev_priv, pipe, _CHV_CMN_DW5_CH0, val);
+	} else {
+		val = vlv_dpio_read(dev_priv, pipe, _CHV_CMN_DW1_CH1);
+		val &= ~(CHV_BUFLEFTENA2_MASK | CHV_BUFRIGHTENA2_MASK);
+		if (ch == DPIO_CH0)
+			val |= CHV_BUFLEFTENA2_FORCE;
+		if (ch == DPIO_CH1)
+			val |= CHV_BUFRIGHTENA2_FORCE;
+		vlv_dpio_write(dev_priv, pipe, _CHV_CMN_DW1_CH1, val);
+	}
+
+	/* program clock channel usage */
+	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW8(ch));
+	val |= CHV_PCS_USEDCLKCHANNEL_OVRRIDE;
+	if (pipe != PIPE_B)
+		val &= ~CHV_PCS_USEDCLKCHANNEL;
+	else
+		val |= CHV_PCS_USEDCLKCHANNEL;
+	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW8(ch), val);
+
+	if (intel_crtc->config->lane_count > 2) {
+		val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW8(ch));
+		val |= CHV_PCS_USEDCLKCHANNEL_OVRRIDE;
+		if (pipe != PIPE_B)
+			val &= ~CHV_PCS_USEDCLKCHANNEL;
+		else
+			val |= CHV_PCS_USEDCLKCHANNEL;
+		vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW8(ch), val);
+	}
+
+	/*
+	 * This a a bit weird since generally CL
+	 * matches the pipe, but here we need to
+	 * pick the CL based on the port.
+	 */
+	val = vlv_dpio_read(dev_priv, pipe, CHV_CMN_DW19(ch));
+	if (pipe != PIPE_B)
+		val &= ~CHV_CMN_USEDCLKCHANNEL;
+	else
+		val |= CHV_CMN_USEDCLKCHANNEL;
+	vlv_dpio_write(dev_priv, pipe, CHV_CMN_DW19(ch), val);
+
+	mutex_unlock(&dev_priv->sb_lock);
+}
diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
index cb89a35..0474428 100644
--- a/drivers/gpu/drm/i915/intel_drv.h
+++ b/drivers/gpu/drm/i915/intel_drv.h
@@ -1337,6 +1337,11 @@ bool intel_dp_source_supports_hbr2(struct intel_dp *intel_dp);
 bool
 intel_dp_get_link_status(struct intel_dp *intel_dp, uint8_t link_status[DP_LINK_STATUS_SIZE]);
 
+static inline unsigned int intel_dp_unused_lane_mask(int lane_count)
+{
+	return ~((1 << lane_count) - 1) & 0xf;
+}
+
 /* intel_dp_aux_backlight.c */
 int intel_dp_aux_init_backlight_funcs(struct intel_connector *intel_connector);
 
diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c
index 2d429d0..578da9f 100644
--- a/drivers/gpu/drm/i915/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/intel_hdmi.c
@@ -1668,81 +1668,9 @@ static void vlv_hdmi_pre_pll_enable(struct intel_encoder *encoder)
 
 static void chv_hdmi_pre_pll_enable(struct intel_encoder *encoder)
 {
-	struct intel_digital_port *dport = enc_to_dig_port(&encoder->base);
-	struct drm_device *dev = encoder->base.dev;
-	struct drm_i915_private *dev_priv = dev->dev_private;
-	struct intel_crtc *intel_crtc =
-		to_intel_crtc(encoder->base.crtc);
-	enum dpio_channel ch = vlv_dport_to_channel(dport);
-	enum pipe pipe = intel_crtc->pipe;
-	u32 val;
-
 	intel_hdmi_prepare(encoder);
 
-	/*
-	 * Must trick the second common lane into life.
-	 * Otherwise we can't even access the PLL.
-	 */
-	if (ch == DPIO_CH0 && pipe == PIPE_B)
-		dport->release_cl2_override =
-			!chv_phy_powergate_ch(dev_priv, DPIO_PHY0, DPIO_CH1, true);
-
-	chv_phy_powergate_lanes(encoder, true, 0x0);
-
-	mutex_lock(&dev_priv->sb_lock);
-
-	/* Assert data lane reset */
-	chv_data_lane_soft_reset(encoder, true);
-
-	/* program left/right clock distribution */
-	if (pipe != PIPE_B) {
-		val = vlv_dpio_read(dev_priv, pipe, _CHV_CMN_DW5_CH0);
-		val &= ~(CHV_BUFLEFTENA1_MASK | CHV_BUFRIGHTENA1_MASK);
-		if (ch == DPIO_CH0)
-			val |= CHV_BUFLEFTENA1_FORCE;
-		if (ch == DPIO_CH1)
-			val |= CHV_BUFRIGHTENA1_FORCE;
-		vlv_dpio_write(dev_priv, pipe, _CHV_CMN_DW5_CH0, val);
-	} else {
-		val = vlv_dpio_read(dev_priv, pipe, _CHV_CMN_DW1_CH1);
-		val &= ~(CHV_BUFLEFTENA2_MASK | CHV_BUFRIGHTENA2_MASK);
-		if (ch == DPIO_CH0)
-			val |= CHV_BUFLEFTENA2_FORCE;
-		if (ch == DPIO_CH1)
-			val |= CHV_BUFRIGHTENA2_FORCE;
-		vlv_dpio_write(dev_priv, pipe, _CHV_CMN_DW1_CH1, val);
-	}
-
-	/* program clock channel usage */
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW8(ch));
-	val |= CHV_PCS_USEDCLKCHANNEL_OVRRIDE;
-	if (pipe != PIPE_B)
-		val &= ~CHV_PCS_USEDCLKCHANNEL;
-	else
-		val |= CHV_PCS_USEDCLKCHANNEL;
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW8(ch), val);
-
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW8(ch));
-	val |= CHV_PCS_USEDCLKCHANNEL_OVRRIDE;
-	if (pipe != PIPE_B)
-		val &= ~CHV_PCS_USEDCLKCHANNEL;
-	else
-		val |= CHV_PCS_USEDCLKCHANNEL;
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW8(ch), val);
-
-	/*
-	 * This a a bit weird since generally CL
-	 * matches the pipe, but here we need to
-	 * pick the CL based on the port.
-	 */
-	val = vlv_dpio_read(dev_priv, pipe, CHV_CMN_DW19(ch));
-	if (pipe != PIPE_B)
-		val &= ~CHV_CMN_USEDCLKCHANNEL;
-	else
-		val |= CHV_CMN_USEDCLKCHANNEL;
-	vlv_dpio_write(dev_priv, pipe, CHV_CMN_DW19(ch), val);
-
-	mutex_unlock(&dev_priv->sb_lock);
+	chv_phy_pre_pll_enable(encoder);
 }
 
 static void chv_hdmi_post_pll_disable(struct intel_encoder *encoder)
-- 
2.4.11

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[PATCH v4 05/10] drm/i915: Unduplicate CHV pre-encoder enabling phy logic

[Ander Conselvan de Oliveira]

The only difference between the DP and HDMI versions was the lane count.
Since lane_count is now set appropriately for HDMI too, get rid of the
duplication and move this to intel_dpio_phy.c

v2: Don't move comments about 2nd common lane staying alive. (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
---
 drivers/gpu/drm/i915/i915_drv.h       |  2 +
 drivers/gpu/drm/i915/intel_dp.c       | 83 +------------------------------
 drivers/gpu/drm/i915/intel_dpio_phy.c | 92 +++++++++++++++++++++++++++++++++++
 drivers/gpu/drm/i915/intel_hdmi.c     | 67 +------------------------
 4 files changed, 98 insertions(+), 146 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
index 4e34d3d..a482297 100644
--- a/drivers/gpu/drm/i915/i915_drv.h
+++ b/drivers/gpu/drm/i915/i915_drv.h
@@ -3584,6 +3584,8 @@ void chv_set_phy_signal_level(struct intel_encoder *encoder,
 void chv_data_lane_soft_reset(struct intel_encoder *encoder,
 			      bool reset);
 void chv_phy_pre_pll_enable(struct intel_encoder *encoder);
+void chv_phy_pre_encoder_enable(struct intel_encoder *encoder);
+void chv_phy_release_cl2_override(struct intel_encoder *encoder);
 
 int intel_gpu_freq(struct drm_i915_private *dev_priv, int val);
 int intel_freq_opcode(struct drm_i915_private *dev_priv, int val);
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index 1f6fd89..2daf874 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -2821,91 +2821,12 @@ static void vlv_dp_pre_pll_enable(struct intel_encoder *encoder)
 
 static void chv_pre_enable_dp(struct intel_encoder *encoder)
 {
-	struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
-	struct intel_digital_port *dport = dp_to_dig_port(intel_dp);
-	struct drm_device *dev = encoder->base.dev;
-	struct drm_i915_private *dev_priv = dev->dev_private;
-	struct intel_crtc *intel_crtc =
-		to_intel_crtc(encoder->base.crtc);
-	enum dpio_channel ch = vlv_dport_to_channel(dport);
-	int pipe = intel_crtc->pipe;
-	int data, i, stagger;
-	u32 val;
-
-	mutex_lock(&dev_priv->sb_lock);
-
-	/* allow hardware to manage TX FIFO reset source */
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW11(ch));
-	val &= ~DPIO_LANEDESKEW_STRAP_OVRD;
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW11(ch), val);
-
-	if (intel_crtc->config->lane_count > 2) {
-		val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW11(ch));
-		val &= ~DPIO_LANEDESKEW_STRAP_OVRD;
-		vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW11(ch), val);
-	}
-
-	/* Program Tx lane latency optimal setting*/
-	for (i = 0; i < intel_crtc->config->lane_count; i++) {
-		/* Set the upar bit */
-		if (intel_crtc->config->lane_count == 1)
-			data = 0x0;
-		else
-			data = (i == 1) ? 0x0 : 0x1;
-		vlv_dpio_write(dev_priv, pipe, CHV_TX_DW14(ch, i),
-				data << DPIO_UPAR_SHIFT);
-	}
-
-	/* Data lane stagger programming */
-	if (intel_crtc->config->port_clock > 270000)
-		stagger = 0x18;
-	else if (intel_crtc->config->port_clock > 135000)
-		stagger = 0xd;
-	else if (intel_crtc->config->port_clock > 67500)
-		stagger = 0x7;
-	else if (intel_crtc->config->port_clock > 33750)
-		stagger = 0x4;
-	else
-		stagger = 0x2;
-
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW11(ch));
-	val |= DPIO_TX2_STAGGER_MASK(0x1f);
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW11(ch), val);
-
-	if (intel_crtc->config->lane_count > 2) {
-		val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW11(ch));
-		val |= DPIO_TX2_STAGGER_MASK(0x1f);
-		vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW11(ch), val);
-	}
-
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW12(ch),
-		       DPIO_LANESTAGGER_STRAP(stagger) |
-		       DPIO_LANESTAGGER_STRAP_OVRD |
-		       DPIO_TX1_STAGGER_MASK(0x1f) |
-		       DPIO_TX1_STAGGER_MULT(6) |
-		       DPIO_TX2_STAGGER_MULT(0));
-
-	if (intel_crtc->config->lane_count > 2) {
-		vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW12(ch),
-			       DPIO_LANESTAGGER_STRAP(stagger) |
-			       DPIO_LANESTAGGER_STRAP_OVRD |
-			       DPIO_TX1_STAGGER_MASK(0x1f) |
-			       DPIO_TX1_STAGGER_MULT(7) |
-			       DPIO_TX2_STAGGER_MULT(5));
-	}
-
-	/* Deassert data lane reset */
-	chv_data_lane_soft_reset(encoder, false);
-
-	mutex_unlock(&dev_priv->sb_lock);
+	chv_phy_pre_encoder_enable(encoder);
 
 	intel_enable_dp(encoder);
 
 	/* Second common lane will stay alive on its own now */
-	if (dport->release_cl2_override) {
-		chv_phy_powergate_ch(dev_priv, DPIO_PHY0, DPIO_CH1, false);
-		dport->release_cl2_override = false;
-	}
+	chv_phy_release_cl2_override(encoder);
 }
 
 static void chv_dp_pre_pll_enable(struct intel_encoder *encoder)
diff --git a/drivers/gpu/drm/i915/intel_dpio_phy.c b/drivers/gpu/drm/i915/intel_dpio_phy.c
index b4ca3ff..ad0e7be 100644
--- a/drivers/gpu/drm/i915/intel_dpio_phy.c
+++ b/drivers/gpu/drm/i915/intel_dpio_phy.c
@@ -244,3 +244,95 @@ void chv_phy_pre_pll_enable(struct intel_encoder *encoder)
 
 	mutex_unlock(&dev_priv->sb_lock);
 }
+
+void chv_phy_pre_encoder_enable(struct intel_encoder *encoder)
+{
+	struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
+	struct intel_digital_port *dport = dp_to_dig_port(intel_dp);
+	struct drm_device *dev = encoder->base.dev;
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	struct intel_crtc *intel_crtc =
+		to_intel_crtc(encoder->base.crtc);
+	enum dpio_channel ch = vlv_dport_to_channel(dport);
+	int pipe = intel_crtc->pipe;
+	int data, i, stagger;
+	u32 val;
+
+	mutex_lock(&dev_priv->sb_lock);
+
+	/* allow hardware to manage TX FIFO reset source */
+	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW11(ch));
+	val &= ~DPIO_LANEDESKEW_STRAP_OVRD;
+	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW11(ch), val);
+
+	if (intel_crtc->config->lane_count > 2) {
+		val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW11(ch));
+		val &= ~DPIO_LANEDESKEW_STRAP_OVRD;
+		vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW11(ch), val);
+	}
+
+	/* Program Tx lane latency optimal setting*/
+	for (i = 0; i < intel_crtc->config->lane_count; i++) {
+		/* Set the upar bit */
+		if (intel_crtc->config->lane_count == 1)
+			data = 0x0;
+		else
+			data = (i == 1) ? 0x0 : 0x1;
+		vlv_dpio_write(dev_priv, pipe, CHV_TX_DW14(ch, i),
+				data << DPIO_UPAR_SHIFT);
+	}
+
+	/* Data lane stagger programming */
+	if (intel_crtc->config->port_clock > 270000)
+		stagger = 0x18;
+	else if (intel_crtc->config->port_clock > 135000)
+		stagger = 0xd;
+	else if (intel_crtc->config->port_clock > 67500)
+		stagger = 0x7;
+	else if (intel_crtc->config->port_clock > 33750)
+		stagger = 0x4;
+	else
+		stagger = 0x2;
+
+	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW11(ch));
+	val |= DPIO_TX2_STAGGER_MASK(0x1f);
+	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW11(ch), val);
+
+	if (intel_crtc->config->lane_count > 2) {
+		val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW11(ch));
+		val |= DPIO_TX2_STAGGER_MASK(0x1f);
+		vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW11(ch), val);
+	}
+
+	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW12(ch),
+		       DPIO_LANESTAGGER_STRAP(stagger) |
+		       DPIO_LANESTAGGER_STRAP_OVRD |
+		       DPIO_TX1_STAGGER_MASK(0x1f) |
+		       DPIO_TX1_STAGGER_MULT(6) |
+		       DPIO_TX2_STAGGER_MULT(0));
+
+	if (intel_crtc->config->lane_count > 2) {
+		vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW12(ch),
+			       DPIO_LANESTAGGER_STRAP(stagger) |
+			       DPIO_LANESTAGGER_STRAP_OVRD |
+			       DPIO_TX1_STAGGER_MASK(0x1f) |
+			       DPIO_TX1_STAGGER_MULT(7) |
+			       DPIO_TX2_STAGGER_MULT(5));
+	}
+
+	/* Deassert data lane reset */
+	chv_data_lane_soft_reset(encoder, false);
+
+	mutex_unlock(&dev_priv->sb_lock);
+}
+
+void chv_phy_release_cl2_override(struct intel_encoder *encoder)
+{
+	struct intel_digital_port *dport = enc_to_dig_port(&encoder->base);
+	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
+
+	if (dport->release_cl2_override) {
+		chv_phy_powergate_ch(dev_priv, DPIO_PHY0, DPIO_CH1, false);
+		dport->release_cl2_override = false;
+	}
+}
diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c
index 578da9f..daaa68d 100644
--- a/drivers/gpu/drm/i915/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/intel_hdmi.c
@@ -1744,68 +1744,8 @@ static void chv_hdmi_pre_enable(struct intel_encoder *encoder)
 	struct intel_crtc *intel_crtc =
 		to_intel_crtc(encoder->base.crtc);
 	const struct drm_display_mode *adjusted_mode = &intel_crtc->config->base.adjusted_mode;
-	enum dpio_channel ch = vlv_dport_to_channel(dport);
-	int pipe = intel_crtc->pipe;
-	int data, i, stagger;
-	u32 val;
-
-	mutex_lock(&dev_priv->sb_lock);
-
-	/* allow hardware to manage TX FIFO reset source */
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW11(ch));
-	val &= ~DPIO_LANEDESKEW_STRAP_OVRD;
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW11(ch), val);
-
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW11(ch));
-	val &= ~DPIO_LANEDESKEW_STRAP_OVRD;
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW11(ch), val);
-
-	/* Program Tx latency optimal setting */
-	for (i = 0; i < 4; i++) {
-		/* Set the upar bit */
-		data = (i == 1) ? 0x0 : 0x1;
-		vlv_dpio_write(dev_priv, pipe, CHV_TX_DW14(ch, i),
-				data << DPIO_UPAR_SHIFT);
-	}
-
-	/* Data lane stagger programming */
-	if (intel_crtc->config->port_clock > 270000)
-		stagger = 0x18;
-	else if (intel_crtc->config->port_clock > 135000)
-		stagger = 0xd;
-	else if (intel_crtc->config->port_clock > 67500)
-		stagger = 0x7;
-	else if (intel_crtc->config->port_clock > 33750)
-		stagger = 0x4;
-	else
-		stagger = 0x2;
 
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW11(ch));
-	val |= DPIO_TX2_STAGGER_MASK(0x1f);
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW11(ch), val);
-
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS23_DW11(ch));
-	val |= DPIO_TX2_STAGGER_MASK(0x1f);
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW11(ch), val);
-
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS01_DW12(ch),
-		       DPIO_LANESTAGGER_STRAP(stagger) |
-		       DPIO_LANESTAGGER_STRAP_OVRD |
-		       DPIO_TX1_STAGGER_MASK(0x1f) |
-		       DPIO_TX1_STAGGER_MULT(6) |
-		       DPIO_TX2_STAGGER_MULT(0));
-
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS23_DW12(ch),
-		       DPIO_LANESTAGGER_STRAP(stagger) |
-		       DPIO_LANESTAGGER_STRAP_OVRD |
-		       DPIO_TX1_STAGGER_MASK(0x1f) |
-		       DPIO_TX1_STAGGER_MULT(7) |
-		       DPIO_TX2_STAGGER_MULT(5));
-
-	/* Deassert data lane reset */
-	chv_data_lane_soft_reset(encoder, false);
-
-	mutex_unlock(&dev_priv->sb_lock);
+	chv_phy_pre_encoder_enable(encoder);
 
 	/* FIXME: Program the support xxx V-dB */
 	/* Use 800mV-0dB */
@@ -1820,10 +1760,7 @@ static void chv_hdmi_pre_enable(struct intel_encoder *encoder)
 	vlv_wait_port_ready(dev_priv, dport, 0x0);
 
 	/* Second common lane will stay alive on its own now */
-	if (dport->release_cl2_override) {
-		chv_phy_powergate_ch(dev_priv, DPIO_PHY0, DPIO_CH1, false);
-		dport->release_cl2_override = false;
-	}
+	chv_phy_release_cl2_override(encoder);
 }
 
 static void intel_hdmi_destroy(struct drm_connector *connector)
-- 
2.4.11

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[PATCH v4 06/10] drm/i915: Unduplicate CHV encoders' post pll disable code

[Ander Conselvan de Oliveira]

The exact same code was used by HDMI and DP encoders, so move it to
intel_dpio_phy.c.

v2: Fix typo in the commit message. (Jim Bride)
v3: Call the new function chv_phy_post_pll_disable() instead of
    chv_phy_post_disable(), as it should be called after the pll
    is disabled. (Ville)

Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
---
 drivers/gpu/drm/i915/i915_drv.h       |  1 +
 drivers/gpu/drm/i915/intel_dp.c       | 30 +-----------------------------
 drivers/gpu/drm/i915/intel_dpio_phy.c | 33 +++++++++++++++++++++++++++++++++
 drivers/gpu/drm/i915/intel_hdmi.c     | 30 +-----------------------------
 4 files changed, 36 insertions(+), 58 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
index a482297..57e61db 100644
--- a/drivers/gpu/drm/i915/i915_drv.h
+++ b/drivers/gpu/drm/i915/i915_drv.h
@@ -3586,6 +3586,7 @@ void chv_data_lane_soft_reset(struct intel_encoder *encoder,
 void chv_phy_pre_pll_enable(struct intel_encoder *encoder);
 void chv_phy_pre_encoder_enable(struct intel_encoder *encoder);
 void chv_phy_release_cl2_override(struct intel_encoder *encoder);
+void chv_phy_post_pll_disable(struct intel_encoder *encoder);
 
 int intel_gpu_freq(struct drm_i915_private *dev_priv, int val);
 int intel_freq_opcode(struct drm_i915_private *dev_priv, int val);
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index 2daf874..26faa12 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -2838,35 +2838,7 @@ static void chv_dp_pre_pll_enable(struct intel_encoder *encoder)
 
 static void chv_dp_post_pll_disable(struct intel_encoder *encoder)
 {
-	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
-	enum pipe pipe = to_intel_crtc(encoder->base.crtc)->pipe;
-	u32 val;
-
-	mutex_lock(&dev_priv->sb_lock);
-
-	/* disable left/right clock distribution */
-	if (pipe != PIPE_B) {
-		val = vlv_dpio_read(dev_priv, pipe, _CHV_CMN_DW5_CH0);
-		val &= ~(CHV_BUFLEFTENA1_MASK | CHV_BUFRIGHTENA1_MASK);
-		vlv_dpio_write(dev_priv, pipe, _CHV_CMN_DW5_CH0, val);
-	} else {
-		val = vlv_dpio_read(dev_priv, pipe, _CHV_CMN_DW1_CH1);
-		val &= ~(CHV_BUFLEFTENA2_MASK | CHV_BUFRIGHTENA2_MASK);
-		vlv_dpio_write(dev_priv, pipe, _CHV_CMN_DW1_CH1, val);
-	}
-
-	mutex_unlock(&dev_priv->sb_lock);
-
-	/*
-	 * Leave the power down bit cleared for at least one
-	 * lane so that chv_powergate_phy_ch() will power
-	 * on something when the channel is otherwise unused.
-	 * When the port is off and the override is removed
-	 * the lanes power down anyway, so otherwise it doesn't
-	 * really matter what the state of power down bits is
-	 * after this.
-	 */
-	chv_phy_powergate_lanes(encoder, false, 0x0);
+	chv_phy_post_pll_disable(encoder);
 }
 
 /*
diff --git a/drivers/gpu/drm/i915/intel_dpio_phy.c b/drivers/gpu/drm/i915/intel_dpio_phy.c
index ad0e7be..348d700 100644
--- a/drivers/gpu/drm/i915/intel_dpio_phy.c
+++ b/drivers/gpu/drm/i915/intel_dpio_phy.c
@@ -336,3 +336,36 @@ void chv_phy_release_cl2_override(struct intel_encoder *encoder)
 		dport->release_cl2_override = false;
 	}
 }
+
+void chv_phy_post_pll_disable(struct intel_encoder *encoder)
+{
+	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
+	enum pipe pipe = to_intel_crtc(encoder->base.crtc)->pipe;
+	u32 val;
+
+	mutex_lock(&dev_priv->sb_lock);
+
+	/* disable left/right clock distribution */
+	if (pipe != PIPE_B) {
+		val = vlv_dpio_read(dev_priv, pipe, _CHV_CMN_DW5_CH0);
+		val &= ~(CHV_BUFLEFTENA1_MASK | CHV_BUFRIGHTENA1_MASK);
+		vlv_dpio_write(dev_priv, pipe, _CHV_CMN_DW5_CH0, val);
+	} else {
+		val = vlv_dpio_read(dev_priv, pipe, _CHV_CMN_DW1_CH1);
+		val &= ~(CHV_BUFLEFTENA2_MASK | CHV_BUFRIGHTENA2_MASK);
+		vlv_dpio_write(dev_priv, pipe, _CHV_CMN_DW1_CH1, val);
+	}
+
+	mutex_unlock(&dev_priv->sb_lock);
+
+	/*
+	 * Leave the power down bit cleared for at least one
+	 * lane so that chv_powergate_phy_ch() will power
+	 * on something when the channel is otherwise unused.
+	 * When the port is off and the override is removed
+	 * the lanes power down anyway, so otherwise it doesn't
+	 * really matter what the state of power down bits is
+	 * after this.
+	 */
+	chv_phy_powergate_lanes(encoder, false, 0x0);
+}
diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c
index daaa68d..ed7889e 100644
--- a/drivers/gpu/drm/i915/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/intel_hdmi.c
@@ -1675,35 +1675,7 @@ static void chv_hdmi_pre_pll_enable(struct intel_encoder *encoder)
 
 static void chv_hdmi_post_pll_disable(struct intel_encoder *encoder)
 {
-	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
-	enum pipe pipe = to_intel_crtc(encoder->base.crtc)->pipe;
-	u32 val;
-
-	mutex_lock(&dev_priv->sb_lock);
-
-	/* disable left/right clock distribution */
-	if (pipe != PIPE_B) {
-		val = vlv_dpio_read(dev_priv, pipe, _CHV_CMN_DW5_CH0);
-		val &= ~(CHV_BUFLEFTENA1_MASK | CHV_BUFRIGHTENA1_MASK);
-		vlv_dpio_write(dev_priv, pipe, _CHV_CMN_DW5_CH0, val);
-	} else {
-		val = vlv_dpio_read(dev_priv, pipe, _CHV_CMN_DW1_CH1);
-		val &= ~(CHV_BUFLEFTENA2_MASK | CHV_BUFRIGHTENA2_MASK);
-		vlv_dpio_write(dev_priv, pipe, _CHV_CMN_DW1_CH1, val);
-	}
-
-	mutex_unlock(&dev_priv->sb_lock);
-
-	/*
-	 * Leave the power down bit cleared for at least one
-	 * lane so that chv_powergate_phy_ch() will power
-	 * on something when the channel is otherwise unused.
-	 * When the port is off and the override is removed
-	 * the lanes power down anyway, so otherwise it doesn't
-	 * really matter what the state of power down bits is
-	 * after this.
-	 */
-	chv_phy_powergate_lanes(encoder, false, 0x0);
+	chv_phy_post_pll_disable(encoder);
 }
 
 static void vlv_hdmi_post_disable(struct intel_encoder *encoder)
-- 
2.4.11

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[PATCH v4 07/10] drm/i915: Unduplicate VLV signal level code

[Ander Conselvan de Oliveira]

The logic for setting signal levels is used for both HDMI and DP with
small variations. But it is similar enough to put behind a function
called from the encoders.

v2: Remove unrelated MST changes due to rebase fumble. (Jim Bride)
    Fix typo in the commit message. (Jim Bride)

v3: Really fix the typo. (Jim)

Cc: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
---
 drivers/gpu/drm/i915/i915_drv.h       |  4 ++++
 drivers/gpu/drm/i915/intel_dp.c       | 20 +++-----------------
 drivers/gpu/drm/i915/intel_dpio_phy.c | 26 ++++++++++++++++++++++++++
 drivers/gpu/drm/i915/intel_hdmi.c     | 14 ++++----------
 4 files changed, 37 insertions(+), 27 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
index 57e61db..8d07f84 100644
--- a/drivers/gpu/drm/i915/i915_drv.h
+++ b/drivers/gpu/drm/i915/i915_drv.h
@@ -3588,6 +3588,10 @@ void chv_phy_pre_encoder_enable(struct intel_encoder *encoder);
 void chv_phy_release_cl2_override(struct intel_encoder *encoder);
 void chv_phy_post_pll_disable(struct intel_encoder *encoder);
 
+void vlv_set_phy_signal_level(struct intel_encoder *encoder,
+			      u32 demph_reg_value, u32 preemph_reg_value,
+			      u32 uniqtranscale_reg_value, u32 tx3_demph);
+
 int intel_gpu_freq(struct drm_i915_private *dev_priv, int val);
 int intel_freq_opcode(struct drm_i915_private *dev_priv, int val);
 
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index 26faa12..6b953b3 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -2946,16 +2946,10 @@ intel_dp_pre_emphasis_max(struct intel_dp *intel_dp, uint8_t voltage_swing)
 
 static uint32_t vlv_signal_levels(struct intel_dp *intel_dp)
 {
-	struct drm_device *dev = intel_dp_to_dev(intel_dp);
-	struct drm_i915_private *dev_priv = dev->dev_private;
-	struct intel_digital_port *dport = dp_to_dig_port(intel_dp);
-	struct intel_crtc *intel_crtc =
-		to_intel_crtc(dport->base.base.crtc);
+	struct intel_encoder *encoder = &dp_to_dig_port(intel_dp)->base;
 	unsigned long demph_reg_value, preemph_reg_value,
 		uniqtranscale_reg_value;
 	uint8_t train_set = intel_dp->train_set[0];
-	enum dpio_channel port = vlv_dport_to_channel(dport);
-	int pipe = intel_crtc->pipe;
 
 	switch (train_set & DP_TRAIN_PRE_EMPHASIS_MASK) {
 	case DP_TRAIN_PRE_EMPH_LEVEL_0:
@@ -3030,16 +3024,8 @@ static uint32_t vlv_signal_levels(struct intel_dp *intel_dp)
 		return 0;
 	}
 
-	mutex_lock(&dev_priv->sb_lock);
-	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW5(port), 0x00000000);
-	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW4(port), demph_reg_value);
-	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW2(port),
-			 uniqtranscale_reg_value);
-	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW3(port), 0x0C782040);
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW11(port), 0x00030000);
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW9(port), preemph_reg_value);
-	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW5(port), 0x80000000);
-	mutex_unlock(&dev_priv->sb_lock);
+	vlv_set_phy_signal_level(encoder, demph_reg_value, preemph_reg_value,
+				 uniqtranscale_reg_value, 0);
 
 	return 0;
 }
diff --git a/drivers/gpu/drm/i915/intel_dpio_phy.c b/drivers/gpu/drm/i915/intel_dpio_phy.c
index 348d700..8fb4fda 100644
--- a/drivers/gpu/drm/i915/intel_dpio_phy.c
+++ b/drivers/gpu/drm/i915/intel_dpio_phy.c
@@ -369,3 +369,29 @@ void chv_phy_post_pll_disable(struct intel_encoder *encoder)
 	 */
 	chv_phy_powergate_lanes(encoder, false, 0x0);
 }
+
+void vlv_set_phy_signal_level(struct intel_encoder *encoder,
+			      u32 demph_reg_value, u32 preemph_reg_value,
+			      u32 uniqtranscale_reg_value, u32 tx3_demph)
+{
+	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
+	struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc);
+	struct intel_digital_port *dport = enc_to_dig_port(&encoder->base);
+	enum dpio_channel port = vlv_dport_to_channel(dport);
+	int pipe = intel_crtc->pipe;
+
+	mutex_lock(&dev_priv->sb_lock);
+	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW5(port), 0x00000000);
+	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW4(port), demph_reg_value);
+	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW2(port),
+			 uniqtranscale_reg_value);
+	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW3(port), 0x0C782040);
+
+	if (tx3_demph)
+		vlv_dpio_write(dev_priv, pipe, VLV_TX3_DW4(port), tx3_demph);
+
+	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW11(port), 0x00030000);
+	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW9(port), preemph_reg_value);
+	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW5(port), DPIO_TX_OCALINIT_EN);
+	mutex_unlock(&dev_priv->sb_lock);
+}
diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c
index ed7889e..5c044ce 100644
--- a/drivers/gpu/drm/i915/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/intel_hdmi.c
@@ -1609,21 +1609,15 @@ static void vlv_hdmi_pre_enable(struct intel_encoder *encoder)
 	val |= 0x001000c4;
 	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW8(port), val);
 
-	/* HDMI 1.0V-2dB */
-	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW5(port), 0);
-	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW4(port), 0x2b245f5f);
-	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW2(port), 0x5578b83a);
-	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW3(port), 0x0c782040);
-	vlv_dpio_write(dev_priv, pipe, VLV_TX3_DW4(port), 0x2b247878);
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW11(port), 0x00030000);
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW9(port), 0x00002000);
-	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW5(port), DPIO_TX_OCALINIT_EN);
-
 	/* Program lane clock */
 	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW14(port), 0x00760018);
 	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW23(port), 0x00400888);
 	mutex_unlock(&dev_priv->sb_lock);
 
+	/* HDMI 1.0V-2dB */
+	vlv_set_phy_signal_level(encoder, 0x2b245f5f, 0x00002000, 0x5578b83a,
+				 0x2b247878);
+
 	intel_hdmi->set_infoframes(&encoder->base,
 				   intel_crtc->config->has_hdmi_sink,
 				   adjusted_mode);
-- 
2.4.11

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[PATCH v4 08/10] drm/i915: Unduplicate VLV phy pre pll enabling code

[Ander Conselvan de Oliveira]

The code used by the DP and HDMI paths was very similar, so make them
share it. Note that this removes the write to signal level registers
from the HDMI pre pll enable path, but that's OK since those are set
in vlv_hdmi_pre_enable() function.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
---
 drivers/gpu/drm/i915/i915_drv.h       |  1 +
 drivers/gpu/drm/i915/intel_dp.c       | 25 +------------------------
 drivers/gpu/drm/i915/intel_dpio_phy.c | 28 ++++++++++++++++++++++++++++
 drivers/gpu/drm/i915/intel_hdmi.c     | 28 +---------------------------
 4 files changed, 31 insertions(+), 51 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
index 8d07f84..8a8a76d 100644
--- a/drivers/gpu/drm/i915/i915_drv.h
+++ b/drivers/gpu/drm/i915/i915_drv.h
@@ -3591,6 +3591,7 @@ void chv_phy_post_pll_disable(struct intel_encoder *encoder);
 void vlv_set_phy_signal_level(struct intel_encoder *encoder,
 			      u32 demph_reg_value, u32 preemph_reg_value,
 			      u32 uniqtranscale_reg_value, u32 tx3_demph);
+void vlv_phy_pre_pll_enable(struct intel_encoder *encoder);
 
 int intel_gpu_freq(struct drm_i915_private *dev_priv, int val);
 int intel_freq_opcode(struct drm_i915_private *dev_priv, int val);
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index 6b953b3..bb26caf 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -2791,32 +2791,9 @@ static void vlv_pre_enable_dp(struct intel_encoder *encoder)
 
 static void vlv_dp_pre_pll_enable(struct intel_encoder *encoder)
 {
-	struct intel_digital_port *dport = enc_to_dig_port(&encoder->base);
-	struct drm_device *dev = encoder->base.dev;
-	struct drm_i915_private *dev_priv = dev->dev_private;
-	struct intel_crtc *intel_crtc =
-		to_intel_crtc(encoder->base.crtc);
-	enum dpio_channel port = vlv_dport_to_channel(dport);
-	int pipe = intel_crtc->pipe;
-
 	intel_dp_prepare(encoder);
 
-	/* Program Tx lane resets to default */
-	mutex_lock(&dev_priv->sb_lock);
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW0(port),
-			 DPIO_PCS_TX_LANE2_RESET |
-			 DPIO_PCS_TX_LANE1_RESET);
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW1(port),
-			 DPIO_PCS_CLK_CRI_RXEB_EIOS_EN |
-			 DPIO_PCS_CLK_CRI_RXDIGFILTSG_EN |
-			 (1<<DPIO_PCS_CLK_DATAWIDTH_SHIFT) |
-				 DPIO_PCS_CLK_SOFT_RESET);
-
-	/* Fix up inter-pair skew failure */
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW12(port), 0x00750f00);
-	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW11(port), 0x00001500);
-	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW14(port), 0x40400000);
-	mutex_unlock(&dev_priv->sb_lock);
+	vlv_phy_pre_pll_enable(encoder);
 }
 
 static void chv_pre_enable_dp(struct intel_encoder *encoder)
diff --git a/drivers/gpu/drm/i915/intel_dpio_phy.c b/drivers/gpu/drm/i915/intel_dpio_phy.c
index 8fb4fda..975965a 100644
--- a/drivers/gpu/drm/i915/intel_dpio_phy.c
+++ b/drivers/gpu/drm/i915/intel_dpio_phy.c
@@ -395,3 +395,31 @@ void vlv_set_phy_signal_level(struct intel_encoder *encoder,
 	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW5(port), DPIO_TX_OCALINIT_EN);
 	mutex_unlock(&dev_priv->sb_lock);
 }
+
+void vlv_phy_pre_pll_enable(struct intel_encoder *encoder)
+{
+	struct intel_digital_port *dport = enc_to_dig_port(&encoder->base);
+	struct drm_device *dev = encoder->base.dev;
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	struct intel_crtc *intel_crtc =
+		to_intel_crtc(encoder->base.crtc);
+	enum dpio_channel port = vlv_dport_to_channel(dport);
+	int pipe = intel_crtc->pipe;
+
+	/* Program Tx lane resets to default */
+	mutex_lock(&dev_priv->sb_lock);
+	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW0(port),
+			 DPIO_PCS_TX_LANE2_RESET |
+			 DPIO_PCS_TX_LANE1_RESET);
+	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW1(port),
+			 DPIO_PCS_CLK_CRI_RXEB_EIOS_EN |
+			 DPIO_PCS_CLK_CRI_RXDIGFILTSG_EN |
+			 (1<<DPIO_PCS_CLK_DATAWIDTH_SHIFT) |
+				 DPIO_PCS_CLK_SOFT_RESET);
+
+	/* Fix up inter-pair skew failure */
+	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW12(port), 0x00750f00);
+	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW11(port), 0x00001500);
+	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW14(port), 0x40400000);
+	mutex_unlock(&dev_priv->sb_lock);
+}
diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c
index 5c044ce..1a58ba7 100644
--- a/drivers/gpu/drm/i915/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/intel_hdmi.c
@@ -1629,35 +1629,9 @@ static void vlv_hdmi_pre_enable(struct intel_encoder *encoder)
 
 static void vlv_hdmi_pre_pll_enable(struct intel_encoder *encoder)
 {
-	struct intel_digital_port *dport = enc_to_dig_port(&encoder->base);
-	struct drm_device *dev = encoder->base.dev;
-	struct drm_i915_private *dev_priv = dev->dev_private;
-	struct intel_crtc *intel_crtc =
-		to_intel_crtc(encoder->base.crtc);
-	enum dpio_channel port = vlv_dport_to_channel(dport);
-	int pipe = intel_crtc->pipe;
-
 	intel_hdmi_prepare(encoder);
 
-	/* Program Tx lane resets to default */
-	mutex_lock(&dev_priv->sb_lock);
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW0(port),
-			 DPIO_PCS_TX_LANE2_RESET |
-			 DPIO_PCS_TX_LANE1_RESET);
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW1(port),
-			 DPIO_PCS_CLK_CRI_RXEB_EIOS_EN |
-			 DPIO_PCS_CLK_CRI_RXDIGFILTSG_EN |
-			 (1<<DPIO_PCS_CLK_DATAWIDTH_SHIFT) |
-			 DPIO_PCS_CLK_SOFT_RESET);
-
-	/* Fix up inter-pair skew failure */
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW12(port), 0x00750f00);
-	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW11(port), 0x00001500);
-	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW14(port), 0x40400000);
-
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW9(port), 0x00002000);
-	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW5(port), DPIO_TX_OCALINIT_EN);
-	mutex_unlock(&dev_priv->sb_lock);
+	vlv_phy_pre_pll_enable(encoder);
 }
 
 static void chv_hdmi_pre_pll_enable(struct intel_encoder *encoder)
-- 
2.4.11

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[PATCH v4 09/10] drm/i915: Unduplicate pre encoder enabling phy code

[Ander Conselvan de Oliveira]

The phy code in vlv_pre_enable_dp() and vlv_hdmi_pre_enable() is
exectly the same, so extract it to intel_dpio_phy.c.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
---
 drivers/gpu/drm/i915/i915_drv.h       |  1 +
 drivers/gpu/drm/i915/intel_dp.c       | 24 +-----------------------
 drivers/gpu/drm/i915/intel_dpio_phy.c | 30 ++++++++++++++++++++++++++++++
 drivers/gpu/drm/i915/intel_hdmi.c     | 19 +------------------
 4 files changed, 33 insertions(+), 41 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
index 8a8a76d..7592cac 100644
--- a/drivers/gpu/drm/i915/i915_drv.h
+++ b/drivers/gpu/drm/i915/i915_drv.h
@@ -3592,6 +3592,7 @@ void vlv_set_phy_signal_level(struct intel_encoder *encoder,
 			      u32 demph_reg_value, u32 preemph_reg_value,
 			      u32 uniqtranscale_reg_value, u32 tx3_demph);
 void vlv_phy_pre_pll_enable(struct intel_encoder *encoder);
+void vlv_phy_pre_encoder_enable(struct intel_encoder *encoder);
 
 int intel_gpu_freq(struct drm_i915_private *dev_priv, int val);
 int intel_freq_opcode(struct drm_i915_private *dev_priv, int val);
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index bb26caf..3633002 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -2762,29 +2762,7 @@ static void vlv_init_panel_power_sequencer(struct intel_dp *intel_dp)
 
 static void vlv_pre_enable_dp(struct intel_encoder *encoder)
 {
-	struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
-	struct intel_digital_port *dport = dp_to_dig_port(intel_dp);
-	struct drm_device *dev = encoder->base.dev;
-	struct drm_i915_private *dev_priv = dev->dev_private;
-	struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc);
-	enum dpio_channel port = vlv_dport_to_channel(dport);
-	int pipe = intel_crtc->pipe;
-	u32 val;
-
-	mutex_lock(&dev_priv->sb_lock);
-
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW8(port));
-	val = 0;
-	if (pipe)
-		val |= (1<<21);
-	else
-		val &= ~(1<<21);
-	val |= 0x001000c4;
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW8(port), val);
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW14(port), 0x00760018);
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW23(port), 0x00400888);
-
-	mutex_unlock(&dev_priv->sb_lock);
+	vlv_phy_pre_encoder_enable(encoder);
 
 	intel_enable_dp(encoder);
 }
diff --git a/drivers/gpu/drm/i915/intel_dpio_phy.c b/drivers/gpu/drm/i915/intel_dpio_phy.c
index 975965a..2c14bf0 100644
--- a/drivers/gpu/drm/i915/intel_dpio_phy.c
+++ b/drivers/gpu/drm/i915/intel_dpio_phy.c
@@ -423,3 +423,33 @@ void vlv_phy_pre_pll_enable(struct intel_encoder *encoder)
 	vlv_dpio_write(dev_priv, pipe, VLV_TX_DW14(port), 0x40400000);
 	mutex_unlock(&dev_priv->sb_lock);
 }
+
+void vlv_phy_pre_encoder_enable(struct intel_encoder *encoder)
+{
+	struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
+	struct intel_digital_port *dport = dp_to_dig_port(intel_dp);
+	struct drm_device *dev = encoder->base.dev;
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc);
+	enum dpio_channel port = vlv_dport_to_channel(dport);
+	int pipe = intel_crtc->pipe;
+	u32 val;
+
+	mutex_lock(&dev_priv->sb_lock);
+
+	/* Enable clock channels for this port */
+	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW8(port));
+	val = 0;
+	if (pipe)
+		val |= (1<<21);
+	else
+		val &= ~(1<<21);
+	val |= 0x001000c4;
+	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW8(port), val);
+
+	/* Program lane clock */
+	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW14(port), 0x00760018);
+	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW23(port), 0x00400888);
+
+	mutex_unlock(&dev_priv->sb_lock);
+}
diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c
index 1a58ba7..11be19e 100644
--- a/drivers/gpu/drm/i915/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/intel_hdmi.c
@@ -1594,25 +1594,8 @@ static void vlv_hdmi_pre_enable(struct intel_encoder *encoder)
 	struct intel_crtc *intel_crtc =
 		to_intel_crtc(encoder->base.crtc);
 	const struct drm_display_mode *adjusted_mode = &intel_crtc->config->base.adjusted_mode;
-	enum dpio_channel port = vlv_dport_to_channel(dport);
-	int pipe = intel_crtc->pipe;
-	u32 val;
-
-	/* Enable clock channels for this port */
-	mutex_lock(&dev_priv->sb_lock);
-	val = vlv_dpio_read(dev_priv, pipe, VLV_PCS01_DW8(port));
-	val = 0;
-	if (pipe)
-		val |= (1<<21);
-	else
-		val &= ~(1<<21);
-	val |= 0x001000c4;
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW8(port), val);
 
-	/* Program lane clock */
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW14(port), 0x00760018);
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW23(port), 0x00400888);
-	mutex_unlock(&dev_priv->sb_lock);
+	vlv_phy_pre_encoder_enable(encoder);
 
 	/* HDMI 1.0V-2dB */
 	vlv_set_phy_signal_level(encoder, 0x2b245f5f, 0x00002000, 0x5578b83a,
-- 
2.4.11

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[PATCH v4 10/10] drm/i915: Move VLV HDMI lane reset work around logic to intel_dpio_phy.c

[Ander Conselvan de Oliveira]

This moves the last phy specific code from the encoders to the phy
specific file.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
---
 drivers/gpu/drm/i915/i915_drv.h       |  1 +
 drivers/gpu/drm/i915/intel_dpio_phy.c | 15 +++++++++++++++
 drivers/gpu/drm/i915/intel_hdmi.c     | 12 +-----------
 3 files changed, 17 insertions(+), 11 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
index 7592cac..e6bd669 100644
--- a/drivers/gpu/drm/i915/i915_drv.h
+++ b/drivers/gpu/drm/i915/i915_drv.h
@@ -3593,6 +3593,7 @@ void vlv_set_phy_signal_level(struct intel_encoder *encoder,
 			      u32 uniqtranscale_reg_value, u32 tx3_demph);
 void vlv_phy_pre_pll_enable(struct intel_encoder *encoder);
 void vlv_phy_pre_encoder_enable(struct intel_encoder *encoder);
+void vlv_phy_reset_lanes(struct intel_encoder *encoder);
 
 int intel_gpu_freq(struct drm_i915_private *dev_priv, int val);
 int intel_freq_opcode(struct drm_i915_private *dev_priv, int val);
diff --git a/drivers/gpu/drm/i915/intel_dpio_phy.c b/drivers/gpu/drm/i915/intel_dpio_phy.c
index 2c14bf0..288da35 100644
--- a/drivers/gpu/drm/i915/intel_dpio_phy.c
+++ b/drivers/gpu/drm/i915/intel_dpio_phy.c
@@ -453,3 +453,18 @@ void vlv_phy_pre_encoder_enable(struct intel_encoder *encoder)
 
 	mutex_unlock(&dev_priv->sb_lock);
 }
+
+void vlv_phy_reset_lanes(struct intel_encoder *encoder)
+{
+	struct intel_digital_port *dport = enc_to_dig_port(&encoder->base);
+	struct drm_i915_private *dev_priv = encoder->base.dev->dev_private;
+	struct intel_crtc *intel_crtc =
+		to_intel_crtc(encoder->base.crtc);
+	enum dpio_channel port = vlv_dport_to_channel(dport);
+	int pipe = intel_crtc->pipe;
+
+	mutex_lock(&dev_priv->sb_lock);
+	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW0(port), 0x00000000);
+	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW1(port), 0x00e00060);
+	mutex_unlock(&dev_priv->sb_lock);
+}
diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c
index 11be19e..e1012d6 100644
--- a/drivers/gpu/drm/i915/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/intel_hdmi.c
@@ -1631,18 +1631,8 @@ static void chv_hdmi_post_pll_disable(struct intel_encoder *encoder)
 
 static void vlv_hdmi_post_disable(struct intel_encoder *encoder)
 {
-	struct intel_digital_port *dport = enc_to_dig_port(&encoder->base);
-	struct drm_i915_private *dev_priv = encoder->base.dev->dev_private;
-	struct intel_crtc *intel_crtc =
-		to_intel_crtc(encoder->base.crtc);
-	enum dpio_channel port = vlv_dport_to_channel(dport);
-	int pipe = intel_crtc->pipe;
-
 	/* Reset lanes to avoid HDMI flicker (VLV w/a) */
-	mutex_lock(&dev_priv->sb_lock);
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW0(port), 0x00000000);
-	vlv_dpio_write(dev_priv, pipe, VLV_PCS_DW1(port), 0x00e00060);
-	mutex_unlock(&dev_priv->sb_lock);
+	vlv_phy_reset_lanes(encoder);
 }
 
 static void chv_hdmi_post_disable(struct intel_encoder *encoder)
-- 
2.4.11

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

✗ Fi.CI.BAT: failure for Unduplicate CHV phy code (rev5)

[Patchwork]

== Series Details ==

Series: Unduplicate CHV phy code (rev5)
URL   : https://patchwork.freedesktop.org/series/5463/
State : failure

== Summary ==

Series 5463v5 Unduplicate CHV phy code
http://patchwork.freedesktop.org/api/1.0/series/5463/revisions/5/mbox/

Test drv_module_reload_basic:
                dmesg-warn -> PASS       (snb-x220t)
Test gem_exec_suspend:
        Subgroup basic-s3:
                fail       -> PASS       (snb-x220t)
Test kms_pipe_crc_basic:
        Subgroup hang-read-crc-pipe-a:
                pass       -> DMESG-WARN (snb-dellxps)
        Subgroup suspend-read-crc-pipe-a:
                pass       -> INCOMPLETE (hsw-gt2)

bdw-nuci7        total:200  pass:188  dwarn:0   dfail:0   fail:0   skip:12 
bdw-ultra        total:200  pass:175  dwarn:0   dfail:0   fail:0   skip:25 
bsw-nuc-2        total:199  pass:158  dwarn:0   dfail:0   fail:0   skip:41 
byt-nuc          total:199  pass:158  dwarn:0   dfail:0   fail:0   skip:41 
hsw-brixbox      total:200  pass:174  dwarn:0   dfail:0   fail:0   skip:26 
hsw-gt2          total:199  pass:176  dwarn:0   dfail:0   fail:1   skip:21 
ilk-hp8440p      total:200  pass:139  dwarn:0   dfail:0   fail:0   skip:61 
ivb-t430s        total:200  pass:169  dwarn:0   dfail:0   fail:0   skip:31 
skl-i7k-2        total:200  pass:173  dwarn:0   dfail:0   fail:0   skip:27 
skl-nuci5        total:200  pass:189  dwarn:0   dfail:0   fail:0   skip:11 
snb-dellxps      total:200  pass:157  dwarn:1   dfail:0   fail:0   skip:42 
snb-x220t        total:200  pass:158  dwarn:0   dfail:0   fail:1   skip:41 

Results at /archive/results/CI_IGT_test/Patchwork_2090/

4fa405ab5848b76c8568c7fb771d389a6695108c drm-intel-nightly: 2016y-04m-27d-10h-47m-35s UTC integration manifest
9e163c0 drm/i915: Move VLV HDMI lane reset work around logic to intel_dpio_phy.c
b7b843d drm/i915: Unduplicate pre encoder enabling phy code
4165303 drm/i915: Unduplicate VLV phy pre pll enabling code
7241e40 drm/i915: Unduplicate VLV signal level code
1879a24 drm/i915: Unduplicate CHV encoders' post pll disable code
3b54e74 drm/i915: Unduplicate CHV pre-encoder enabling phy logic
66e88ec drm/i915: Unduplicate CHV phy-releated pre pll enabling code
8a2b013 drm/i915: Unduplicate chv_data_lane_soft_reset()
4a6d52d drm/i915: Unduplicate CHV signal level code
5a20188 drm/i915: Set crtc_state->lane_count for HDMI

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

Re: ✗ Fi.CI.BAT: failure for Unduplicate CHV phy code (rev5)

[Ander Conselvan De Oliveira]

On Wed, 2016-04-27 at 13:23 +0000, Patchwork wrote:
> == Series Details ==
> 
> Series: Unduplicate CHV phy code (rev5)
> URL   : https://patchwork.freedesktop.org/series/5463/
> State : failure
> 
> == Summary ==
> 
> Series 5463v5 Unduplicate CHV phy code
> http://patchwork.freedesktop.org/api/1.0/series/5463/revisions/5/mbox/
> 
> Test drv_module_reload_basic:
>                 dmesg-warn -> PASS       (snb-x220t)
> Test gem_exec_suspend:
>         Subgroup basic-s3:
>                 fail       -> PASS       (snb-x220t)
> Test kms_pipe_crc_basic:
>         Subgroup hang-read-crc-pipe-a:
>                 pass       -> DMESG-WARN (snb-dellxps)

[  303.915830] ------------[ cut here ]------------
[  303.915859] WARNING: CPU: 5 PID: 6657 at drivers/gpu/drm/i915/intel_display.c:13529 intel_atomic_commit+0x1271/0x1400 [i915]
[  303.915861] pipe A vblank wait timed out

https://bugs.freedesktop.org/show_bug.cgi?id=95125

>         Subgroup suspend-read-crc-pipe-a:
>                 pass       -> INCOMPLETE (hsw-gt2)

dmesg ends with

[  505.669959] kms_pipe_crc_basic: starting subtest suspend-read-crc-pipe-A

Seems very unlikely this would be caused by this series. The only code that is
run on hsw machines is setting the lane count field in crtc_state, but that is
not used anywhere.

Are there any know issues with this machine?


Ander

> 
> bdw-nuci7        total:200  pass:188  dwarn:0   dfail:0   fail:0   skip:12 
> bdw-ultra        total:200  pass:175  dwarn:0   dfail:0   fail:0   skip:25 
> bsw-nuc-2        total:199  pass:158  dwarn:0   dfail:0   fail:0   skip:41 
> byt-nuc          total:199  pass:158  dwarn:0   dfail:0   fail:0   skip:41 
> hsw-brixbox      total:200  pass:174  dwarn:0   dfail:0   fail:0   skip:26 
> hsw-gt2          total:199  pass:176  dwarn:0   dfail:0   fail:1   skip:21 
> ilk-hp8440p      total:200  pass:139  dwarn:0   dfail:0   fail:0   skip:61 
> ivb-t430s        total:200  pass:169  dwarn:0   dfail:0   fail:0   skip:31 
> skl-i7k-2        total:200  pass:173  dwarn:0   dfail:0   fail:0   skip:27 
> skl-nuci5        total:200  pass:189  dwarn:0   dfail:0   fail:0   skip:11 
> snb-dellxps      total:200  pass:157  dwarn:1   dfail:0   fail:0   skip:42 
> snb-x220t        total:200  pass:158  dwarn:0   dfail:0   fail:1   skip:41 
> 
> Results at /archive/results/CI_IGT_test/Patchwork_2090/
> 
> 4fa405ab5848b76c8568c7fb771d389a6695108c drm-intel-nightly: 2016y-04m-27d-10h
> -47m-35s UTC integration manifest
> 9e163c0 drm/i915: Move VLV HDMI lane reset work around logic to
> intel_dpio_phy.c
> b7b843d drm/i915: Unduplicate pre encoder enabling phy code
> 4165303 drm/i915: Unduplicate VLV phy pre pll enabling code
> 7241e40 drm/i915: Unduplicate VLV signal level code
> 1879a24 drm/i915: Unduplicate CHV encoders' post pll disable code
> 3b54e74 drm/i915: Unduplicate CHV pre-encoder enabling phy logic
> 66e88ec drm/i915: Unduplicate CHV phy-releated pre pll enabling code
> 8a2b013 drm/i915: Unduplicate chv_data_lane_soft_reset()
> 4a6d52d drm/i915: Unduplicate CHV signal level code
> 5a20188 drm/i915: Set crtc_state->lane_count for HDMI
> 
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

Re: ✗ Fi.CI.BAT: failure for Unduplicate CHV phy code (rev5)

[Tomi Sarvela]

Hello,

On Wednesday 27 April 2016 16:36:13 Ander Conselvan De Oliveira wrote:
> >         Subgroup suspend-read-crc-pipe-a:
> >                 pass       -> INCOMPLETE (hsw-gt2)
> 
> dmesg ends with
> 
> [  505.669959] kms_pipe_crc_basic: starting subtest suspend-read-crc-pipe-A
> 
> Seems very unlikely this would be caused by this series. The only code that
> is run on hsw machines is setting the lane count field in crtc_state, but
> that is not used anywhere.
> 
> Are there any know issues with this machine?

There is no known issues with this hardware itself. There is one known issue 
with HSW and drm-intel kernel, which has taken a while to figure out. I think 
it still exists in the baseline kernel where patch is applied.

(It's hard to replicate with IGT, but newest Mesa seems to hit it quite 
regularly).

Regards,

Tomi




> 
> 
> Ander
> 
> > bdw-nuci7        total:200  pass:188  dwarn:0   dfail:0   fail:0   skip:12
> > bdw-ultra        total:200  pass:175  dwarn:0   dfail:0   fail:0   skip:25
> > bsw-nuc-2        total:199  pass:158  dwarn:0   dfail:0   fail:0   skip:41
> > byt-nuc          total:199  pass:158  dwarn:0   dfail:0   fail:0   skip:41
> > hsw-brixbox      total:200  pass:174  dwarn:0   dfail:0   fail:0   skip:26
> > hsw-gt2          total:199  pass:176  dwarn:0   dfail:0   fail:1   skip:21
> > ilk-hp8440p      total:200  pass:139  dwarn:0   dfail:0   fail:0   skip:61
> > ivb-t430s        total:200  pass:169  dwarn:0   dfail:0   fail:0   skip:31
> > skl-i7k-2        total:200  pass:173  dwarn:0   dfail:0   fail:0   skip:27
> > skl-nuci5        total:200  pass:189  dwarn:0   dfail:0   fail:0   skip:11
> > snb-dellxps      total:200  pass:157  dwarn:1   dfail:0   fail:0   skip:42
> > snb-x220t        total:200  pass:158  dwarn:0   dfail:0   fail:1   skip:41
> > 
> > Results at /archive/results/CI_IGT_test/Patchwork_2090/
> > 
> > 4fa405ab5848b76c8568c7fb771d389a6695108c drm-intel-nightly:
> > 2016y-04m-27d-10h -47m-35s UTC integration manifest
> > 9e163c0 drm/i915: Move VLV HDMI lane reset work around logic to
> > intel_dpio_phy.c
> > b7b843d drm/i915: Unduplicate pre encoder enabling phy code
> > 4165303 drm/i915: Unduplicate VLV phy pre pll enabling code
> > 7241e40 drm/i915: Unduplicate VLV signal level code
> > 1879a24 drm/i915: Unduplicate CHV encoders' post pll disable code
> > 3b54e74 drm/i915: Unduplicate CHV pre-encoder enabling phy logic
> > 66e88ec drm/i915: Unduplicate CHV phy-releated pre pll enabling code
> > 8a2b013 drm/i915: Unduplicate chv_data_lane_soft_reset()
> > 4a6d52d drm/i915: Unduplicate CHV signal level code
> > 5a20188 drm/i915: Set crtc_state->lane_count for HDMI

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

Re: ✗ Fi.CI.BAT: failure for Unduplicate CHV phy code (rev5)

[Ander Conselvan De Oliveira]

On Wed, 2016-04-27 at 17:39 +0300, Tomi Sarvela wrote:
> Hello,
> 
> On Wednesday 27 April 2016 16:36:13 Ander Conselvan De Oliveira wrote:
> > >         Subgroup suspend-read-crc-pipe-a:
> > >                 pass       -> INCOMPLETE (hsw-gt2)
> > 
> > dmesg ends with
> > 
> > [  505.669959] kms_pipe_crc_basic: starting subtest suspend-read-crc-pipe-A
> > 
> > Seems very unlikely this would be caused by this series. The only code that
> > is run on hsw machines is setting the lane count field in crtc_state, but
> > that is not used anywhere.
> > 
> > Are there any know issues with this machine?
> 
> There is no known issues with this hardware itself. There is one known issue 
> with HSW and drm-intel kernel, which has taken a while to figure out. I think 
> it still exists in the baseline kernel where patch is applied.
> 
> (It's hard to replicate with IGT, but newest Mesa seems to hit it quite 
> regularly).


Patches pushed to dinq.

Thanks,
Ander

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx