From: Jesse Barnes <jbarnes@virtuousgeek.org>
To: ville.syrjala@linux.intel.com
Cc: intel-gfx@lists.freedesktop.org
Subject: Re: [PATCH 04/11] drm/i915: Handle 320 vs. 333 MHz cdclk on vlv
Date: Wed, 25 Jun 2014 11:53:18 -0700 [thread overview]
Message-ID: <20140625115318.4a934087@jbarnes-desktop> (raw)
In-Reply-To: <1402655877-6460-5-git-send-email-ville.syrjala@linux.intel.com>
On Fri, 13 Jun 2014 13:37:50 +0300
ville.syrjala@linux.intel.com wrote:
> From: Ville Syrjälä <ville.syrjala@linux.intel.com>
>
> Depending on the HPLL frequency one of the supported cdclk frquencies is
> either 320MHz or 333MHz. Figure out which one it is to accurately pick
> the minimal required cdclk. This would also avoid a warning from the
> cdclk code where it compares the actual cdclk read out from the hardware
> with a value that was calculated using valleyview_calc_cdclk().
>
> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
> ---
> drivers/gpu/drm/i915/intel_display.c | 9 ++++++---
> 1 file changed, 6 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
> index 61d7ea2..1f3985f 100644
> --- a/drivers/gpu/drm/i915/intel_display.c
> +++ b/drivers/gpu/drm/i915/intel_display.c
> @@ -4509,19 +4509,22 @@ static void valleyview_set_cdclk(struct drm_device *dev, int cdclk)
> static int valleyview_calc_cdclk(struct drm_i915_private *dev_priv,
> int max_pixclk)
> {
> + int vco = valleyview_get_vco(dev_priv);
> + int freq_320 = (vco << 1) % 320000 != 0 ? 333333 : 320000;
> +
> /*
> * Really only a few cases to deal with, as only 4 CDclks are supported:
> * 200MHz
> * 267MHz
> - * 320MHz
> + * 320/333MHz (depends on HPLL freq)
> * 400MHz
> * So we check to see whether we're above 90% of the lower bin and
> * adjust if needed.
> */
> - if (max_pixclk > 320000*9/10)
> + if (max_pixclk > freq_320*9/10)
> return 400000;
> else if (max_pixclk > 266667*9/10)
> - return 320000;
> + return freq_320;
> else
> return 266667;
> /* Looks like the 200MHz CDclk freq doesn't work on some configs */
Looks good. This doc searching has been fun.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
--
Jesse Barnes, Intel Open Source Technology Center
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
next prev parent reply other threads:[~2014-06-25 18:52 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-06-13 10:37 [PATCH 00/11] drm/i915: VLV display clock/phy stuff ville.syrjala
2014-06-13 10:37 ` [PATCH 01/11] drm/i915: Change vlv cdclk to use kHz units ville.syrjala
2014-06-25 18:36 ` Jesse Barnes
2014-06-13 10:37 ` [PATCH 02/11] drm/i915: Give names to the CCK_DISPLAY_CLOCK_CONTROL bits ville.syrjala
2014-06-25 18:45 ` Jesse Barnes
2014-06-13 10:37 ` [PATCH 03/11] drm/i915: Move vlv cdclk code to .get_display_clock_speed() ville.syrjala
2014-06-25 18:47 ` Jesse Barnes
2014-07-07 9:17 ` Daniel Vetter
2014-06-13 10:37 ` [PATCH 04/11] drm/i915: Handle 320 vs. 333 MHz cdclk on vlv ville.syrjala
2014-06-25 18:53 ` Jesse Barnes [this message]
2014-06-13 10:37 ` [PATCH 05/11] drm/i915: Use 200MHz cdclk on vlv when all pipes are off ville.syrjala
2014-06-25 18:54 ` Jesse Barnes
2014-06-25 19:32 ` Ville Syrjälä
2014-06-13 10:37 ` [PATCH 06/11] drm/i915: Wait for cdclk change to occure when going for 400MHz ville.syrjala
2014-06-25 18:54 ` Jesse Barnes
2014-06-13 10:37 ` [PATCH 07/11] drm/i915: Warn if there's a cdclk change in progess ville.syrjala
2014-06-25 18:55 ` Jesse Barnes
2014-06-25 19:34 ` Ville Syrjälä
2014-07-07 9:26 ` Daniel Vetter
2014-06-13 10:37 ` [PATCH 08/11] drm/i915: Kill duplicated cdclk readout code from i2c ville.syrjala
2014-06-25 18:58 ` Jesse Barnes
2014-06-13 10:37 ` [PATCH 09/11] drm/i915: Pull the cmnlane tricks into its own power well ops ville.syrjala
2014-06-25 18:59 ` Jesse Barnes
2014-06-13 10:37 ` [PATCH 10/11] drm/i915: Move VLV cmnlane workaround to intel_power_domains_init_hw() ville.syrjala
2014-06-25 19:03 ` Jesse Barnes
2014-06-25 19:43 ` Ville Syrjälä
2014-06-13 10:37 ` [WIP][PATCH 11/11] drm/i915: Turn off clocks when disp2d is powered down ville.syrjala
2014-06-25 19:03 ` Jesse Barnes
2014-07-07 9:30 ` Daniel Vetter
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20140625115318.4a934087@jbarnes-desktop \
--to=jbarnes@virtuousgeek.org \
--cc=intel-gfx@lists.freedesktop.org \
--cc=ville.syrjala@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox