From: Daniel Vetter <daniel@ffwll.ch>
To: Imre Deak <imre.deak@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Subject: Re: [PATCH 04/16] drm/i915: unify legacy S3 suspend and S4 freeze handlers
Date: Thu, 11 Sep 2014 11:00:02 +0200 [thread overview]
Message-ID: <20140911090002.GG15520@phenom.ffwll.local> (raw)
In-Reply-To: <1410362229-814-5-git-send-email-imre.deak@intel.com>
On Wed, Sep 10, 2014 at 06:16:57PM +0300, Imre Deak wrote:
> i915_suspend() is called from the DRM legacy S3 suspend/S4 freeze paths
> and the switcheroo suspend path. For switcheroo we only ever need to
> perform a full suspend (PM_EVENT_SUSPEND) and for the DRM legacy path
> we can handle the S4 freeze (PM_EVENT_FREEZE) the same way as S3
> suspend. The only difference atm between suspend and freeze is that
> during freeze we don't disable the PCI device, but there is no reason
> why we can't do so. So unify the two cases to reduce complexity.
>
> Note that for the DRM legacy case the thaw event is not handled, so
> we disable the display before creating the hibernation image and it
> won't get re-enabled until reboot. We could fix this leaving the
> display enabled for the image creation/writing (if we care enough
> about UMS), but this can be done as a follow-up.
UMS doesn't even get compiled any more, please don't try to fix it ;-)
My plan is to garbage-collect it all around when 3.17 is out the door.
-Daniel
>
> Signed-off-by: Imre Deak <imre.deak@intel.com>
> ---
> drivers/gpu/drm/i915/i915_drv.c | 8 +++-----
> 1 file changed, 3 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/i915_drv.c b/drivers/gpu/drm/i915/i915_drv.c
> index 7fa34bd..bf4ff5e 100644
> --- a/drivers/gpu/drm/i915/i915_drv.c
> +++ b/drivers/gpu/drm/i915/i915_drv.c
> @@ -648,11 +648,9 @@ int i915_suspend(struct drm_device *dev, pm_message_t state)
> if (error)
> return error;
>
> - if (state.event == PM_EVENT_SUSPEND) {
> - /* Shut down the device */
> - pci_disable_device(dev->pdev);
> - pci_set_power_state(dev->pdev, PCI_D3hot);
> - }
> + /* Shut down the device */
> + pci_disable_device(dev->pdev);
> + pci_set_power_state(dev->pdev, PCI_D3hot);
>
> return 0;
> }
> --
> 1.8.4
>
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx@lists.freedesktop.org
> http://lists.freedesktop.org/mailman/listinfo/intel-gfx
--
Daniel Vetter
Software Engineer, Intel Corporation
+41 (0) 79 365 57 48 - http://blog.ffwll.ch
next prev parent reply other threads:[~2014-09-11 8:59 UTC|newest]
Thread overview: 49+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-09-10 15:16 [PATCH 00/16] fix VLV S4 suspend/resume, unify S3/S4 handlers Imre Deak
2014-09-10 15:16 ` [PATCH 01/16] drm/i915: vlv: fix gunit HW state corruption during S4 suspend Imre Deak
2014-09-15 17:26 ` Sagar Arun Kamble
2014-09-15 17:42 ` Imre Deak
2014-09-29 15:30 ` Sagar Arun Kamble
2014-10-21 12:34 ` Ville Syrjälä
2014-09-10 15:16 ` [PATCH 02/16] drm/i915: remove dead code from legacy suspend handler Imre Deak
2014-10-21 11:56 ` Ville Syrjälä
2014-10-21 12:11 ` Daniel Vetter
2014-09-10 15:16 ` [PATCH 03/16] drm/i915: factor out i915_drm_suspend_late Imre Deak
2014-09-10 15:16 ` [PATCH 04/16] drm/i915: unify legacy S3 suspend and S4 freeze handlers Imre Deak
2014-09-11 9:00 ` Daniel Vetter [this message]
2014-09-11 12:39 ` Imre Deak
2014-09-10 15:16 ` [PATCH 05/16] drm/i915: propagate error from legacy resume handler Imre Deak
2014-09-10 15:16 ` [PATCH 06/16] drm/i915: vlv: fix switcheroo/legacy suspend/resume Imre Deak
2014-09-29 15:33 ` Sagar Arun Kamble
2014-09-10 15:17 ` [PATCH 07/16] drm/i915: fix S4 suspend while switcheroo state is off Imre Deak
2014-10-21 12:41 ` Ville Syrjälä
2014-10-21 13:08 ` Imre Deak
2014-10-21 13:24 ` Ville Syrjälä
2014-09-10 15:17 ` [PATCH 08/16] drm/i915: remove unused restore_gtt_mappings optimization during suspend Imre Deak
2014-09-11 7:49 ` Chris Wilson
2014-09-11 11:59 ` Imre Deak
2014-09-11 14:15 ` Jesse Barnes
2014-10-21 13:50 ` Ville Syrjälä
2014-11-06 21:50 ` Jesse Barnes
2014-09-11 8:57 ` Daniel Vetter
2014-09-10 15:17 ` [PATCH 09/16] drm/i915: check for GT faults during S3 resume and S4 restore too Imre Deak
2014-09-11 7:47 ` Chris Wilson
2014-09-11 11:53 ` Imre Deak
2014-09-15 15:21 ` [PATCH v2 09/16] drm/i915: check for GT faults in all resume handlers and driver load time Imre Deak
2014-09-15 16:45 ` Chris Wilson
2014-09-10 15:17 ` [PATCH 10/16] drm/i915: enable output polling during S4 thaw Imre Deak
2014-09-10 15:17 ` [PATCH 11/16] drm/i915: disable/re-enable PCI device around S4 freeze/thaw Imre Deak
2014-10-21 13:16 ` Ville Syrjälä
2014-09-10 15:17 ` [PATCH 12/16] drm/i915: unify S3 and S4 suspend/resume handlers Imre Deak
2014-09-10 15:17 ` [PATCH 13/16] drm/i915: sanitize suspend/resume helper function names Imre Deak
2014-09-10 15:17 ` [PATCH 14/16] drm/i915: add poweroff_late handler Imre Deak
2014-10-21 13:32 ` Ville Syrjälä
2014-09-10 15:17 ` [PATCH 15/16] drm/i915: unify switcheroo and legacy suspend/resume handlers Imre Deak
2014-09-10 15:17 ` [PATCH 16/16] drm/i915: add comments on what stage a given PM handler is called Imre Deak
2014-09-15 15:23 ` [PATCH v2 " Imre Deak
2014-10-21 13:42 ` [PATCH " Ville Syrjälä
2014-10-21 13:51 ` Imre Deak
2014-09-10 15:52 ` [PATCH 00/16] fix VLV S4 suspend/resume, unify S3/S4 handlers Daniel Vetter
2014-09-10 18:38 ` Imre Deak
2014-09-11 9:02 ` Daniel Vetter
2014-09-11 13:48 ` Imre Deak
2014-10-21 14:42 ` Ville Syrjälä
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20140911090002.GG15520@phenom.ffwll.local \
--to=daniel@ffwll.ch \
--cc=imre.deak@intel.com \
--cc=intel-gfx@lists.freedesktop.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox