From: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
To: Jani Nikula <jani.nikula@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Subject: Re: [PATCH v3 1/6] drm/i915/dsi: clean up vlv gpio table and definitions
Date: Thu, 7 Apr 2016 15:59:32 +0300 [thread overview]
Message-ID: <20160407125932.GF4329@intel.com> (raw)
In-Reply-To: <34932140b78a3de7f825c78380a08c930694651b.1459884518.git.jani.nikula@intel.com>
On Tue, Apr 05, 2016 at 10:30:49PM +0300, Jani Nikula wrote:
> Define and store the pad base offset in the array, and reference the
> pconf0 and padval registers through macros. Add VLV prefixes to
> macros. Use spec nomenclature for pconf0 and padval.
>
> v2: Address Ville's review comments, squash another patch here.
>
> v3: Use the names Ville dug up in the specs.
>
> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
> ---
> drivers/gpu/drm/i915/intel_dsi_panel_vbt.c | 87 ++++++++++++++----------------
> 1 file changed, 39 insertions(+), 48 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/intel_dsi_panel_vbt.c b/drivers/gpu/drm/i915/intel_dsi_panel_vbt.c
> index af1a47b5224f..21964ba0bf34 100644
> --- a/drivers/gpu/drm/i915/intel_dsi_panel_vbt.c
> +++ b/drivers/gpu/drm/i915/intel_dsi_panel_vbt.c
> @@ -58,50 +58,41 @@ static inline struct vbt_panel *to_vbt_panel(struct drm_panel *panel)
>
> #define NS_KHZ_RATIO 1000000
>
> -#define GPI0_NC_0_HV_DDI0_HPD 0x4130
> -#define GPIO_NC_0_HV_DDI0_PAD 0x4138
> -#define GPIO_NC_1_HV_DDI0_DDC_SDA 0x4120
> -#define GPIO_NC_1_HV_DDI0_DDC_SDA_PAD 0x4128
> -#define GPIO_NC_2_HV_DDI0_DDC_SCL 0x4110
> -#define GPIO_NC_2_HV_DDI0_DDC_SCL_PAD 0x4118
> -#define GPIO_NC_3_PANEL0_VDDEN 0x4140
> -#define GPIO_NC_3_PANEL0_VDDEN_PAD 0x4148
> -#define GPIO_NC_4_PANEL0_BLKEN 0x4150
> -#define GPIO_NC_4_PANEL0_BLKEN_PAD 0x4158
> -#define GPIO_NC_5_PANEL0_BLKCTL 0x4160
> -#define GPIO_NC_5_PANEL0_BLKCTL_PAD 0x4168
> -#define GPIO_NC_6_PCONF0 0x4180
> -#define GPIO_NC_6_PAD 0x4188
> -#define GPIO_NC_7_PCONF0 0x4190
> -#define GPIO_NC_7_PAD 0x4198
> -#define GPIO_NC_8_PCONF0 0x4170
> -#define GPIO_NC_8_PAD 0x4178
> -#define GPIO_NC_9_PCONF0 0x4100
> -#define GPIO_NC_9_PAD 0x4108
> -#define GPIO_NC_10_PCONF0 0x40E0
> -#define GPIO_NC_10_PAD 0x40E8
> -#define GPIO_NC_11_PCONF0 0x40F0
> -#define GPIO_NC_11_PAD 0x40F8
> +/* base offsets for gpio pads */
> +#define VLV_GPIO_NC_0_HV_DDI0_HPD 0x4130
> +#define VLV_GPIO_NC_1_HV_DDI0_DDC_SDA 0x4120
> +#define VLV_GPIO_NC_2_HV_DDI0_DDC_SCL 0x4110
> +#define VLV_GPIO_NC_3_PANEL0_VDDEN 0x4140
> +#define VLV_GPIO_NC_4_PANEL0_BKLTEN 0x4150
> +#define VLV_GPIO_NC_5_PANEL0_BKLTCTL 0x4160
> +#define VLV_GPIO_NC_6_HV_DDI1_HPD 0x4180
> +#define VLV_GPIO_NC_7_HV_DDI1_DDC_SDA 0x4190
> +#define VLV_GPIO_NC_8_HV_DDI1_DDC_SCL 0x4170
> +#define VLV_GPIO_NC_9_PANEL1_VDDEN 0x4100
> +#define VLV_GPIO_NC_10_PANEL1_BKLTEN 0x40E0
> +#define VLV_GPIO_NC_11_PANEL1_BKLTCTL 0x40F0
> +
> +#define VLV_GPIO_PCONF0(base_offset) (base_offset)
> +#define VLV_GPIO_PAD_VAL(base_offset) ((base_offset) + 8)
>
> struct gpio_table {
> - u16 function_reg;
> - u16 pad_reg;
> - u8 init;
> + u16 base_offset;
> + bool init;
> };
>
> -static struct gpio_table gtable[] = {
> - { GPI0_NC_0_HV_DDI0_HPD, GPIO_NC_0_HV_DDI0_PAD, 0 },
> - { GPIO_NC_1_HV_DDI0_DDC_SDA, GPIO_NC_1_HV_DDI0_DDC_SDA_PAD, 0 },
> - { GPIO_NC_2_HV_DDI0_DDC_SCL, GPIO_NC_2_HV_DDI0_DDC_SCL_PAD, 0 },
> - { GPIO_NC_3_PANEL0_VDDEN, GPIO_NC_3_PANEL0_VDDEN_PAD, 0 },
> - { GPIO_NC_4_PANEL0_BLKEN, GPIO_NC_4_PANEL0_BLKEN_PAD, 0 },
> - { GPIO_NC_5_PANEL0_BLKCTL, GPIO_NC_5_PANEL0_BLKCTL_PAD, 0 },
> - { GPIO_NC_6_PCONF0, GPIO_NC_6_PAD, 0 },
> - { GPIO_NC_7_PCONF0, GPIO_NC_7_PAD, 0 },
> - { GPIO_NC_8_PCONF0, GPIO_NC_8_PAD, 0 },
> - { GPIO_NC_9_PCONF0, GPIO_NC_9_PAD, 0 },
> - { GPIO_NC_10_PCONF0, GPIO_NC_10_PAD, 0},
> - { GPIO_NC_11_PCONF0, GPIO_NC_11_PAD, 0}
> +static struct gpio_table vlv_gpio_table[] = {
> + { VLV_GPIO_NC_0_HV_DDI0_HPD },
> + { VLV_GPIO_NC_1_HV_DDI0_DDC_SDA },
> + { VLV_GPIO_NC_2_HV_DDI0_DDC_SCL },
> + { VLV_GPIO_NC_3_PANEL0_VDDEN },
> + { VLV_GPIO_NC_4_PANEL0_BKLTEN },
> + { VLV_GPIO_NC_5_PANEL0_BKLTCTL },
> + { VLV_GPIO_NC_6_HV_DDI1_HPD },
> + { VLV_GPIO_NC_7_HV_DDI1_DDC_SDA },
> + { VLV_GPIO_NC_8_HV_DDI1_DDC_SCL },
> + { VLV_GPIO_NC_9_PANEL1_VDDEN },
> + { VLV_GPIO_NC_10_PANEL1_BKLTEN },
> + { VLV_GPIO_NC_11_PANEL1_BKLTCTL },
> };
>
> static inline enum port intel_dsi_seq_port_to_port(u8 port)
> @@ -199,7 +190,7 @@ static const u8 *mipi_exec_delay(struct intel_dsi *intel_dsi, const u8 *data)
> static const u8 *mipi_exec_gpio(struct intel_dsi *intel_dsi, const u8 *data)
> {
> u8 gpio_source, gpio_index, action, port;
> - u16 function, pad;
> + u16 pconf0, padval;
> u32 val;
> struct drm_device *dev = intel_dsi->base.base.dev;
> struct drm_i915_private *dev_priv = dev->dev_private;
> @@ -218,7 +209,7 @@ static const u8 *mipi_exec_gpio(struct intel_dsi *intel_dsi, const u8 *data)
> /* pull up/down */
> action = *data++ & 1;
>
> - if (gpio_index >= ARRAY_SIZE(gtable)) {
> + if (gpio_index >= ARRAY_SIZE(vlv_gpio_table)) {
> DRM_DEBUG_KMS("unknown gpio index %u\n", gpio_index);
> goto out;
> }
> @@ -242,21 +233,21 @@ static const u8 *mipi_exec_gpio(struct intel_dsi *intel_dsi, const u8 *data)
> }
> }
>
> - function = gtable[gpio_index].function_reg;
> - pad = gtable[gpio_index].pad_reg;
> + pconf0 = VLV_GPIO_PCONF0(vlv_gpio_table[gpio_index].base_offset);
> + padval = VLV_GPIO_PAD_VAL(vlv_gpio_table[gpio_index].base_offset);
>
> mutex_lock(&dev_priv->sb_lock);
> - if (!gtable[gpio_index].init) {
> + if (!vlv_gpio_table[gpio_index].init) {
> /* program the function */
> /* FIXME: remove constant below */
> - vlv_iosf_sb_write(dev_priv, port, function, 0x2000CC00);
> - gtable[gpio_index].init = 1;
> + vlv_iosf_sb_write(dev_priv, port, pconf0, 0x2000CC00);
> + vlv_gpio_table[gpio_index].init = true;
> }
>
> val = 0x4 | action;
>
> /* pull up/down */
> - vlv_iosf_sb_write(dev_priv, port, pad, val);
> + vlv_iosf_sb_write(dev_priv, port, padval, val);
> mutex_unlock(&dev_priv->sb_lock);
>
> out:
> --
> 2.1.4
--
Ville Syrjälä
Intel OTC
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
next prev parent reply other threads:[~2016-04-07 12:59 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-04-05 19:30 [PATCH v3 0/6] drm/i915/dsi: improved gpio element support for vlv/chv/bxt Jani Nikula
2016-04-05 19:30 ` [PATCH v3 1/6] drm/i915/dsi: clean up vlv gpio table and definitions Jani Nikula
2016-04-07 12:59 ` Ville Syrjälä [this message]
2016-04-05 19:30 ` [PATCH v3 2/6] drm/i915/dsi: abstract VLV gpio element execution to a separate function Jani Nikula
2016-04-07 13:00 ` Ville Syrjälä
2016-04-05 19:30 ` [PATCH v3 3/6] drm/i915/dsi: use a temp variable for referencing the gpio table Jani Nikula
2016-04-07 13:01 ` Ville Syrjälä
2016-04-07 13:39 ` Jani Nikula
2016-04-05 19:30 ` [PATCH v3 4/6] drm/i915/dsi: add support for sequence block v3 gpio for VLV Jani Nikula
2016-04-07 13:04 ` Ville Syrjälä
2016-04-07 13:14 ` Jani Nikula
2016-04-05 19:30 ` [PATCH v3 5/6] drm/i915/dsi: add support for gpio elements on CHV Jani Nikula
2016-04-07 13:16 ` Ville Syrjälä
2016-04-05 19:30 ` [PATCH v3 6/6] drm/i915/bxt: add bxt dsi gpio element support Jani Nikula
2016-04-07 11:47 ` [PATCH] " Jani Nikula
2016-04-07 12:21 ` Ville Syrjälä
2016-04-07 12:55 ` Jani Nikula
2016-04-06 7:27 ` ✗ Fi.CI.BAT: failure for drm/i915/dsi: improved gpio element support for vlv/chv/bxt (rev2) Patchwork
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20160407125932.GF4329@intel.com \
--to=ville.syrjala@linux.intel.com \
--cc=intel-gfx@lists.freedesktop.org \
--cc=jani.nikula@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).