Re: [PATCH 2/4] drm/i915: Fix system resume if PCI device remained enabled

["Ville Syrjälä" <ville.syrjala@linux.intel.com>]

On Mon, Apr 18, 2016 at 10:04:20AM +0300, Imre Deak wrote:
> During system resume we depended on pci_enable_device() also putting the
> device into PCI D0 state. This won't work if the PCI device was already
> enabled but still in D3 state. This is because pci_enable_device() is
> refcounted and will not change the HW state if called with a non-zero
> refcount. Leaving the device in D3 will make all subsequent device
> accesses fail.
> 
> This didn't cause a problem most of the time, since we resumed with an
> enable refcount of 0. But it fails at least after module reload because
> after that we also happen to leak a PCI device enable reference: During
> probing we call drm_get_pci_dev() which will enable the PCI device, but
> during device removal drm_put_dev() won't disable it. This is a bug of
> its own in DRM core, but without much harm as it only leaves the PCI
> device enabled. Fixing it is also a bit more involved, due to DRM
> mid-layering and because it affects non-i915 drivers too. The fix in
> this patch is valid regardless of the problem in DRM core.
> 
> CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
> CC: stable@vger.kernel.org
> Signed-off-by: Imre Deak <imre.deak@intel.com>
> ---
>  drivers/gpu/drm/i915/i915_drv.c | 9 ++++++++-
>  1 file changed, 8 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/gpu/drm/i915/i915_drv.c b/drivers/gpu/drm/i915/i915_drv.c
> index d550ae2..7eaa93e 100644
> --- a/drivers/gpu/drm/i915/i915_drv.c
> +++ b/drivers/gpu/drm/i915/i915_drv.c
> @@ -803,7 +803,7 @@ static int i915_drm_resume(struct drm_device *dev)
>  static int i915_drm_resume_early(struct drm_device *dev)
>  {
>  	struct drm_i915_private *dev_priv = dev->dev_private;
> -	int ret = 0;
> +	int ret;
>  
>  	/*
>  	 * We have a resume ordering issue with the snd-hda driver also
> @@ -814,6 +814,13 @@ static int i915_drm_resume_early(struct drm_device *dev)
>  	 * FIXME: This should be solved with a special hdmi sink device or
>  	 * similar so that power domains can be employed.
>  	 */
> +
> +	ret = pci_set_power_state(dev->pdev, PCI_D0);
> +	if (ret) {
> +		DRM_ERROR("failed to set PCI D0 power state (%d)\n", ret);
> +		goto out;
> +	}

Hmm. Doesn't this already happen from pci bus resume_noirq hook?

> +
>  	if (pci_enable_device(dev->pdev)) {
>  		ret = -EIO;
>  		goto out;
> -- 
> 2.5.0

-- 
Ville Syrjälä
Intel OTC
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx