From: "O'Rourke, Tom" <tom.orourke@intel.com>
To: intel-gfx@lists.freedesktop.org
Cc: paulo.r.zanoni@intel.com, radoslaw.szwichtenberg@intel.com,
Tom O'Rourke <Tom.O'Rourke@intel.com>
Subject: Re: [PATCH v4 00/21] Add support for GuC-based SLPC
Date: Thu, 28 Apr 2016 16:01:14 -0700 [thread overview]
Message-ID: <20160428230114.GA223857@torourke-desk1> (raw)
In-Reply-To: <1461805865-212590-1-git-send-email-tom.orourke@intel.com>
On Wed, Apr 27, 2016 at 06:10:44PM -0700, tom.orourke@intel.com wrote:
> From: Tom O'Rourke <Tom.O'Rourke@intel.com>
>
> SLPC (Single Loop Power Controller) is a replacement for
> some host-based power management features. The SLPC
> implemenation runs in firmware on GuC.
>
> This series has been tested with SKL guc firmware
> version 6.1.
>
> The graphics power management features in SLPC in those
> versions are called GTPERF, BALANCER, and DCC.
>
> GTPERF is a combination of DFPS (Dynamic FPS) and Turbo.
> DFPS adjusts requested graphics frequency to maintain
> target framerate. Turbo adjusts requested graphics
> frequency to maintain target GT busyness; this includes
> an adaptive boost turbo method.
>
> BALANCER adjusts balance between power budgets for IA
> and GT in power limited scenarios. BALANCER is only
> active when all display pipes are in "game" mode.
>
> DCC (Duty Cycle Control) adjusts requested graphics
> frequency and stalls guc-scheduler to maintain actual
> graphics frequency in efficient range.
>
> The v3 series can be found in the archive at
> "[Intel-gfx] [PATCH v3 00/25] Add support for GuC-based SLPC"
> https://lists.freedesktop.org/archives/intel-gfx/2016-April/091771.html
>
> This v4 series incorporates feedback from internal code
> reviews for Android and Yocto projects. This series also
> drops the Broxton patches; the Broxton firmware has not
> been published yet. Broxton support can be added later
> when the Broxton firmware is available.
>
> Also, the "DO NOT MERGE" patches to enable SLPC and guc
> submission by default have been dropped. These can be
> added later after SLPC has been shown to outperform
> host-based power management; this may require a newer
> version of the GuC firmware.
>
> With SLPC disabled by default, this series should be
> safe to merge now.
>
> VIZ-6773, VIZ-6889
Thank you to Chris, Daniel and Imre for your comments.
I agree that some of the suggested changes should be made.
Whether those changes should be made before merging or with
later patches will be someone else's problem.
I won't be sending another version of this series.
Thanks,
Tom O'Rourke
>
> Sagar Arun Kamble (4):
> drm/i915/slpc: Add Display mode event related data structures
> drm/i915/slpc: Notification of Display mode change
> drm/i915/slpc: Notification of Refresh Rate change
> drm/i915/slpc: Fail intel_runtime_suspend if SLPC or RPS not active
>
> Tom O'Rourke (17):
> drm/i915/slpc: Expose guc functions for use with SLPC
> drm/i915/slpc: Add has_slpc capability flag
> drm/i915/slpc: Add slpc_version_check
> drm/i915/slpc: Add enable_slpc module parameter
> drm/i915/slpc: Use intel_slpc_* functions if supported
> drm/i915/slpc: Enable SLPC in guc if supported
> drm/i915/slpc: If using SLPC, do not set frequency
> drm/i915/slpc: Allocate/Release/Initialize SLPC shared data
> drm/i915/slpc: Setup rps frequency values during SLPC init
> drm/i915/slpc: Update current requested frequency
> drm/i915/slpc: Send reset event
> drm/i915/slpc: Send shutdown event
> drm/i915/slpc: Add slpc_status enum values
> drm/i915/slpc: Add parameter unset/set/get functions
> drm/i915/slpc: Add slpc support for max/min freq
> drm/i915/slpc: Add enable/disable debugfs for slpc
> drm/i915/slpc: Add i915_slpc_info to debugfs
>
> drivers/gpu/drm/i915/Makefile | 5 +-
> drivers/gpu/drm/i915/i915_debugfs.c | 456 +++++++++++++++++++++++++
> drivers/gpu/drm/i915/i915_drv.c | 4 +-
> drivers/gpu/drm/i915/i915_drv.h | 7 +
> drivers/gpu/drm/i915/i915_guc_submission.c | 6 +-
> drivers/gpu/drm/i915/i915_params.c | 6 +
> drivers/gpu/drm/i915/i915_params.h | 1 +
> drivers/gpu/drm/i915/i915_reg.h | 1 +
> drivers/gpu/drm/i915/i915_sysfs.c | 21 ++
> drivers/gpu/drm/i915/intel_display.c | 2 +
> drivers/gpu/drm/i915/intel_dp.c | 2 +
> drivers/gpu/drm/i915/intel_drv.h | 11 +
> drivers/gpu/drm/i915/intel_guc.h | 13 +
> drivers/gpu/drm/i915/intel_guc_loader.c | 36 ++
> drivers/gpu/drm/i915/intel_pm.c | 42 ++-
> drivers/gpu/drm/i915/intel_slpc.c | 516 +++++++++++++++++++++++++++++
> drivers/gpu/drm/i915/intel_slpc.h | 217 ++++++++++++
> 17 files changed, 1329 insertions(+), 17 deletions(-)
> create mode 100644 drivers/gpu/drm/i915/intel_slpc.c
> create mode 100644 drivers/gpu/drm/i915/intel_slpc.h
>
> --
> 1.9.1
>
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
next prev parent reply other threads:[~2016-04-28 23:01 UTC|newest]
Thread overview: 41+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-04-28 1:10 [PATCH v4 00/21] Add support for GuC-based SLPC tom.orourke
2016-04-28 1:10 ` [PATCH 01/21] drm/i915/slpc: Expose guc functions for use with SLPC tom.orourke
2016-04-28 7:00 ` Chris Wilson
2016-04-28 1:10 ` [PATCH 02/21] drm/i915/slpc: Add has_slpc capability flag tom.orourke
2016-04-28 1:10 ` [PATCH 03/21] drm/i915/slpc: Add slpc_version_check tom.orourke
2016-04-28 6:46 ` Chris Wilson
2016-04-28 1:10 ` [PATCH 04/21] drm/i915/slpc: Add enable_slpc module parameter tom.orourke
2016-04-28 7:02 ` Chris Wilson
2016-04-28 1:10 ` [PATCH 05/21] drm/i915/slpc: Use intel_slpc_* functions if supported tom.orourke
2016-04-28 1:10 ` [PATCH 06/21] drm/i915/slpc: Enable SLPC in guc " tom.orourke
2016-04-28 1:10 ` [PATCH 07/21] drm/i915/slpc: If using SLPC, do not set frequency tom.orourke
2016-04-28 6:34 ` Chris Wilson
2016-04-28 1:10 ` [PATCH 08/21] drm/i915/slpc: Allocate/Release/Initialize SLPC shared data tom.orourke
2016-04-28 7:15 ` Chris Wilson
2016-04-28 1:10 ` [PATCH 09/21] drm/i915/slpc: Setup rps frequency values during SLPC init tom.orourke
2016-04-28 6:41 ` Chris Wilson
2016-04-28 1:10 ` [PATCH 10/21] drm/i915/slpc: Update current requested frequency tom.orourke
2016-04-28 6:25 ` Chris Wilson
2016-04-28 1:10 ` [PATCH 11/21] drm/i915/slpc: Send reset event tom.orourke
2016-04-28 1:10 ` [PATCH 12/21] drm/i915/slpc: Send shutdown event tom.orourke
2016-04-28 7:07 ` Chris Wilson
2016-04-28 1:10 ` [PATCH 13/21] drm/i915/slpc: Add Display mode event related data structures tom.orourke
2016-04-28 1:10 ` [PATCH 14/21] drm/i915/slpc: Notification of Display mode change tom.orourke
2016-04-28 1:10 ` [PATCH 15/21] drm/i915/slpc: Notification of Refresh Rate change tom.orourke
2016-04-28 8:38 ` Daniel Vetter
2016-04-28 8:41 ` Daniel Vetter
2016-04-29 9:09 ` Ville Syrjälä
2016-04-28 1:11 ` [PATCH 16/21] drm/i915/slpc: Add slpc_status enum values tom.orourke
2016-04-28 1:11 ` [PATCH 17/21] drm/i915/slpc: Add parameter unset/set/get functions tom.orourke
2016-04-28 1:11 ` [PATCH 18/21] drm/i915/slpc: Add slpc support for max/min freq tom.orourke
2016-04-28 1:11 ` [PATCH 19/21] drm/i915/slpc: Add enable/disable debugfs for slpc tom.orourke
2016-04-28 7:28 ` Chris Wilson
2016-04-28 1:11 ` [PATCH 20/21] drm/i915/slpc: Add i915_slpc_info to debugfs tom.orourke
2016-04-28 1:11 ` [PATCH 21/21] drm/i915/slpc: Fail intel_runtime_suspend if SLPC or RPS not active tom.orourke
2016-04-28 6:56 ` Chris Wilson
2016-04-28 7:57 ` Imre Deak
2016-04-28 8:00 ` Chris Wilson
2016-04-29 9:34 ` Imre Deak
2016-04-28 7:16 ` ✓ Fi.CI.BAT: success for Add support for GuC-based SLPC (rev4) Patchwork
2016-04-28 23:01 ` O'Rourke, Tom [this message]
2016-04-29 8:47 ` [PATCH v4 00/21] Add support for GuC-based SLPC Chris Wilson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20160428230114.GA223857@torourke-desk1 \
--to=tom.orourke@intel.com \
--cc=Tom.O'Rourke@intel.com \
--cc=intel-gfx@lists.freedesktop.org \
--cc=paulo.r.zanoni@intel.com \
--cc=radoslaw.szwichtenberg@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox