From: Daniel Vetter <daniel@ffwll.ch>
To: ville.syrjala@linux.intel.com
Cc: intel-gfx@lists.freedesktop.org
Subject: Re: [PATCH 03/12] drm/i915: Avoid mixing up SST and MST in DDI setup
Date: Fri, 29 Jul 2016 11:16:19 +0200 [thread overview]
Message-ID: <20160729091619.GX6232@phenom.ffwll.local> (raw)
In-Reply-To: <1469717448-4297-4-git-send-email-ville.syrjala@linux.intel.com>
On Thu, Jul 28, 2016 at 05:50:39PM +0300, ville.syrjala@linux.intel.com wrote:
> From: Ville Syrjälä <ville.syrjala@linux.intel.com>
>
> The MST vs. SST selection should depend purely on the choice of the
> connector/encoder. So don't try to determine the correct DDI mode
> based on the intel_dp->is_mst, which simply tells us whether the sink
> is in MST mode or not. Instead derive the information from the encoder
> type. Since the link training code deals in non-fake encoders, we'll
> also need to keep a second copy of that information around, which we'll
> now designate as 'link_mst'.
>
> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Hm, I think it'd be nice if we could shovel all this stuff into the crtc
state I think, instead of noodling it out of somewhere else. But since we
always update it in pre_enable hooks it should be all fine even with
TEST_ONLY atomic.
I digress, change looks good.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
> ---
> drivers/gpu/drm/i915/intel_ddi.c | 21 +++------------------
> drivers/gpu/drm/i915/intel_dp.c | 1 +
> drivers/gpu/drm/i915/intel_drv.h | 1 +
> 3 files changed, 5 insertions(+), 18 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
> index dd1d6fe12297..3b3a0a808477 100644
> --- a/drivers/gpu/drm/i915/intel_ddi.c
> +++ b/drivers/gpu/drm/i915/intel_ddi.c
> @@ -1111,7 +1111,6 @@ void intel_ddi_enable_transcoder_func(struct drm_crtc *crtc)
> {
> struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
> struct intel_encoder *intel_encoder = intel_ddi_get_crtc_encoder(crtc);
> - struct drm_encoder *encoder = &intel_encoder->base;
> struct drm_device *dev = crtc->dev;
> struct drm_i915_private *dev_priv = to_i915(dev);
> enum pipe pipe = intel_crtc->pipe;
> @@ -1177,29 +1176,15 @@ void intel_ddi_enable_transcoder_func(struct drm_crtc *crtc)
> temp |= TRANS_DDI_MODE_SELECT_HDMI;
> else
> temp |= TRANS_DDI_MODE_SELECT_DVI;
> -
> } else if (type == INTEL_OUTPUT_ANALOG) {
> temp |= TRANS_DDI_MODE_SELECT_FDI;
> temp |= (intel_crtc->config->fdi_lanes - 1) << 1;
> -
> } else if (type == INTEL_OUTPUT_DP ||
> type == INTEL_OUTPUT_EDP) {
> - struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
> -
> - if (intel_dp->is_mst) {
> - temp |= TRANS_DDI_MODE_SELECT_DP_MST;
> - } else
> - temp |= TRANS_DDI_MODE_SELECT_DP_SST;
> -
> + temp |= TRANS_DDI_MODE_SELECT_DP_SST;
> temp |= DDI_PORT_WIDTH(intel_crtc->config->lane_count);
> } else if (type == INTEL_OUTPUT_DP_MST) {
> - struct intel_dp *intel_dp = &enc_to_mst(encoder)->primary->dp;
> -
> - if (intel_dp->is_mst) {
> - temp |= TRANS_DDI_MODE_SELECT_DP_MST;
> - } else
> - temp |= TRANS_DDI_MODE_SELECT_DP_SST;
> -
> + temp |= TRANS_DDI_MODE_SELECT_DP_MST;
> temp |= DDI_PORT_WIDTH(intel_crtc->config->lane_count);
> } else {
> WARN(1, "Invalid encoder type %d for pipe %c\n",
> @@ -2105,7 +2090,7 @@ void intel_ddi_prepare_link_retrain(struct intel_dp *intel_dp)
>
> val = DP_TP_CTL_ENABLE |
> DP_TP_CTL_LINK_TRAIN_PAT1 | DP_TP_CTL_SCRAMBLE_DISABLE;
> - if (intel_dp->is_mst)
> + if (intel_dp->link_mst)
> val |= DP_TP_CTL_MODE_MST;
> else {
> val |= DP_TP_CTL_MODE_SST;
> diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
> index 8c38e3483989..0096c651c21f 100644
> --- a/drivers/gpu/drm/i915/intel_dp.c
> +++ b/drivers/gpu/drm/i915/intel_dp.c
> @@ -1651,6 +1651,7 @@ void intel_dp_set_link_params(struct intel_dp *intel_dp,
> {
> intel_dp->link_rate = pipe_config->port_clock;
> intel_dp->lane_count = pipe_config->lane_count;
> + intel_dp->link_mst = intel_crtc_has_type(pipe_config, INTEL_OUTPUT_DP_MST);
> }
>
> static void intel_dp_prepare(struct intel_encoder *encoder)
> diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
> index e74d851868c5..70d7f33d6747 100644
> --- a/drivers/gpu/drm/i915/intel_drv.h
> +++ b/drivers/gpu/drm/i915/intel_drv.h
> @@ -852,6 +852,7 @@ struct intel_dp {
> int link_rate;
> uint8_t lane_count;
> uint8_t sink_count;
> + bool link_mst;
> bool has_audio;
> bool detect_done;
> enum hdmi_force_audio force_audio;
> --
> 2.7.4
>
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/intel-gfx
--
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
next prev parent reply other threads:[~2016-07-29 9:16 UTC|newest]
Thread overview: 54+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-07-28 14:50 [PATCH 00/12] drm/i915: Move DP link retraining to hotplug work etc ville.syrjala
2016-07-28 14:50 ` [PATCH 01/12] drm/i915: Ignore initial lid state for eDP ville.syrjala
2016-07-28 15:47 ` Chris Wilson
2016-07-28 16:01 ` Ville Syrjälä
2016-07-28 16:36 ` Chris Wilson
2016-07-28 16:48 ` Ville Syrjälä
2016-07-28 14:50 ` [PATCH 02/12] drm/i915: Read PSR caps/intermediate freqs/etc. only once on eDP ville.syrjala
2016-07-28 17:30 ` Chris Wilson
2016-07-28 17:45 ` Ville Syrjälä
2016-07-29 13:52 ` [PATCH v3 " ville.syrjala
2016-07-28 14:50 ` [PATCH 03/12] drm/i915: Avoid mixing up SST and MST in DDI setup ville.syrjala
2016-07-29 9:16 ` Daniel Vetter [this message]
2016-07-29 9:55 ` Ville Syrjälä
2016-08-02 14:20 ` Daniel Vetter
2016-08-01 9:24 ` Maarten Lankhorst
2016-07-28 14:50 ` [PATCH 04/12] drm/i915: Reject mixing MST and SST/HDMI on the same digital port ville.syrjala
2016-07-29 9:19 ` Daniel Vetter
2016-07-29 11:28 ` Ville Syrjälä
2016-08-02 14:22 ` Daniel Vetter
2016-08-01 9:28 ` Maarten Lankhorst
2016-07-28 14:50 ` [PATCH 05/12] drm/i915: Track active streams also for DP SST ville.syrjala
2016-07-29 9:22 ` Daniel Vetter
2016-07-29 11:36 ` Ville Syrjälä
2016-07-29 18:36 ` Jim Bride
2016-08-02 14:28 ` Daniel Vetter
2016-07-28 14:50 ` [PATCH 06/12] drm/i915: Allow MST sinks to work even if drm_probe_ddc() fails ville.syrjala
2016-07-29 9:29 ` Daniel Vetter
2016-07-29 11:41 ` Ville Syrjälä
2016-07-29 13:51 ` [PATCH v2 " ville.syrjala
2016-07-28 14:50 ` [PATCH 07/12] drm/i915: Move DP link retraining into intel_dp_detect() ville.syrjala
2016-07-28 19:48 ` Manasi Navare
2016-07-28 20:15 ` Ville Syrjälä
2016-07-29 0:36 ` Manasi Navare
2016-07-29 9:52 ` Ville Syrjälä
2016-07-29 21:42 ` Manasi Navare
2016-07-29 21:45 ` Manasi Navare
2016-08-01 10:03 ` Ville Syrjälä
2016-07-29 20:37 ` Jim Bride
2016-07-28 14:50 ` [PATCH 08/12] drm/i915: Skip dpcd/edid read unless there was a long hpd ville.syrjala
2016-07-28 15:38 ` Chris Wilson
2016-07-28 15:44 ` Ville Syrjälä
2016-07-28 14:50 ` [PATCH 09/12] drm/i915: Remove useless rate_to_index() usage ville.syrjala
2016-07-29 9:33 ` Daniel Vetter
2016-07-28 14:50 ` [PATCH 10/12] drm/i915: Allow rate_to_index() to return non-exact matches ville.syrjala
2016-07-29 9:35 ` Daniel Vetter
2016-07-29 11:43 ` Ville Syrjälä
2016-07-28 14:50 ` [PATCH 11/12] drm/i915: Don't try to ack sink irqs when there are none ville.syrjala
2016-07-29 9:38 ` Daniel Vetter
2016-07-28 14:50 ` [RFC][PATCH 12/12] drm/i915: Add encoder .sync_state() hook ville.syrjala
2016-07-29 9:42 ` Daniel Vetter
2016-07-28 15:39 ` ✗ Ro.CI.BAT: failure for drm/i915: Move DP link retraining to hotplug work etc Patchwork
2016-07-29 14:27 ` ✗ Ro.CI.BAT: failure for drm/i915: Move DP link retraining to hotplug work etc. (rev3) Patchwork
2016-08-04 12:35 ` Ville Syrjälä
2016-08-04 13:08 ` [PATCH 00/12] drm/i915: Move DP link retraining to hotplug work etc Ville Syrjälä
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20160729091619.GX6232@phenom.ffwll.local \
--to=daniel@ffwll.ch \
--cc=intel-gfx@lists.freedesktop.org \
--cc=ville.syrjala@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox