From: Daniel Vetter <daniel@ffwll.ch>
To: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Subject: Re: [PATCH 09/15] drm/i915: Convert intel_dvo to use atomic state
Date: Thu, 18 Aug 2016 15:36:28 +0200 [thread overview]
Message-ID: <20160818133628.GK6232@phenom.ffwll.local> (raw)
In-Reply-To: <1470755054-32699-10-git-send-email-maarten.lankhorst@linux.intel.com>
On Tue, Aug 09, 2016 at 05:04:08PM +0200, Maarten Lankhorst wrote:
> Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
> ---
> drivers/gpu/drm/i915/intel_dvo.c | 12 +++++-------
> 1 file changed, 5 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/intel_dvo.c b/drivers/gpu/drm/i915/intel_dvo.c
> index 141483fdcf7b..642c5550a1e5 100644
> --- a/drivers/gpu/drm/i915/intel_dvo.c
> +++ b/drivers/gpu/drm/i915/intel_dvo.c
> @@ -194,13 +194,12 @@ static void intel_enable_dvo(struct intel_encoder *encoder,
> {
> struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
> struct intel_dvo *intel_dvo = enc_to_dvo(encoder);
> - struct intel_crtc *crtc = to_intel_crtc(encoder->base.crtc);
> i915_reg_t dvo_reg = intel_dvo->dev.dvo_reg;
> u32 temp = I915_READ(dvo_reg);
>
> intel_dvo->dev.dev_ops->mode_set(&intel_dvo->dev,
> - &crtc->config->base.mode,
> - &crtc->config->base.adjusted_mode);
> + &pipe_config->base.mode,
> + &pipe_config->base.adjusted_mode);
>
> I915_WRITE(dvo_reg, temp | DVO_ENABLE);
> I915_READ(dvo_reg);
> @@ -262,10 +261,9 @@ static void intel_dvo_pre_enable(struct intel_encoder *encoder,
> struct intel_crtc_state *pipe_config,
> struct drm_connector_state *conn_state)
> {
> - struct drm_device *dev = encoder->base.dev;
> - struct drm_i915_private *dev_priv = to_i915(dev);
> - struct intel_crtc *crtc = to_intel_crtc(encoder->base.crtc);
> - const struct drm_display_mode *adjusted_mode = &crtc->config->base.adjusted_mode;
> + struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
> + struct intel_crtc *crtc = to_intel_crtc(pipe_config->base.crtc);
> + const struct drm_display_mode *adjusted_mode = &pipe_config->base.adjusted_mode;
> struct intel_dvo *intel_dvo = enc_to_dvo(encoder);
> int pipe = crtc->pipe;
> u32 dvo_val;
> --
> 2.7.4
>
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/intel-gfx
--
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
next prev parent reply other threads:[~2016-08-18 13:36 UTC|newest]
Thread overview: 43+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-08-09 15:03 [PATCH 00/15] drm/i915: Use connector atomic state in encoders Maarten Lankhorst
2016-08-09 15:04 ` [PATCH 01/15] drm/i915: handle DP_MST correctly in bxt_get_dpll Maarten Lankhorst
2016-08-18 13:17 ` Daniel Vetter
2016-08-09 15:04 ` [PATCH 02/15] drm/i915: Pass atomic state to crtc enable/disable functions Maarten Lankhorst
2016-08-18 13:19 ` Daniel Vetter
2016-08-09 15:04 ` [PATCH 03/15] drm/i915: Remove unused mode_set hook from encoder Maarten Lankhorst
2016-08-18 13:20 ` Daniel Vetter
2016-08-09 15:04 ` [PATCH 04/15] drm/i915: Walk over encoders in crtc enable/disable using atomic state Maarten Lankhorst
2016-08-22 14:28 ` Daniel Vetter
2016-08-09 15:04 ` [PATCH 05/15] drm/i915: Pass crtc_state and connector_state to encoder functions Maarten Lankhorst
2016-08-18 13:30 ` Daniel Vetter
2016-08-22 8:06 ` Maarten Lankhorst
2016-08-22 14:32 ` Daniel Vetter
2016-08-23 8:18 ` Maarten Lankhorst
2016-08-23 8:33 ` Daniel Vetter
2016-08-23 11:48 ` Daniel Vetter
2016-08-09 15:04 ` [PATCH 06/15] drm/i915: Make encoder->compute_config take the connector state Maarten Lankhorst
2016-08-18 13:31 ` Daniel Vetter
2016-08-09 15:04 ` [PATCH 07/15] drm/i915: Remove unused loop from intel_dp_mst_compute_config Maarten Lankhorst
2016-08-18 13:34 ` Daniel Vetter
2016-08-22 12:43 ` Maarten Lankhorst
2016-08-22 14:33 ` Daniel Vetter
2016-08-09 15:04 ` [PATCH 08/15] drm/i915: Convert intel_crt to use atomic state Maarten Lankhorst
2016-08-18 13:35 ` Daniel Vetter
2016-08-09 15:04 ` [PATCH 09/15] drm/i915: Convert intel_dvo " Maarten Lankhorst
2016-08-18 13:36 ` Daniel Vetter [this message]
2016-08-09 15:04 ` [PATCH 10/15] drm/i915: Convert intel_dsi " Maarten Lankhorst
2016-08-18 13:43 ` Daniel Vetter
2016-08-09 15:04 ` [PATCH 11/15] drm/i915: Convert intel_sdvo " Maarten Lankhorst
2016-08-18 13:44 ` Daniel Vetter
2016-08-09 15:04 ` [PATCH 12/15] drm/i915: Convert intel_lvds " Maarten Lankhorst
2016-08-18 13:47 ` Daniel Vetter
2016-08-09 15:04 ` [PATCH 13/15] drm/i915: Convert intel_dp_mst " Maarten Lankhorst
2016-08-18 13:54 ` Daniel Vetter
2016-08-09 15:04 ` [PATCH 14/15] drm/i915: Convert intel_dp " Maarten Lankhorst
2016-08-18 14:01 ` Daniel Vetter
2016-08-09 15:04 ` [PATCH 15/15] drm/i915: Use more atomic state in intel_color.c Maarten Lankhorst
2016-08-18 14:02 ` Daniel Vetter
2016-08-09 15:55 ` ✗ Ro.CI.BAT: failure for drm/i915: Use connector atomic state in encoders Patchwork
2016-08-10 7:53 ` Patchwork
2016-08-18 14:04 ` [PATCH 00/15] " Daniel Vetter
2016-08-22 8:12 ` Maarten Lankhorst
-- strict thread matches above, loose matches on Subject: below --
2016-07-07 11:55 [PATCH 01/15] drm/i915: handle DP_MST correctly in bxt_get_dpll Maarten Lankhorst
2016-07-07 11:55 ` [PATCH 09/15] drm/i915: Convert intel_dvo to use atomic state Maarten Lankhorst
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20160818133628.GK6232@phenom.ffwll.local \
--to=daniel@ffwll.ch \
--cc=intel-gfx@lists.freedesktop.org \
--cc=maarten.lankhorst@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox