From: David Airlie <airlied@redhat.com>
To: Michal Nazarewicz <mina86@mina86.com>
Cc: intel-gfx@lists.freedesktop.org
Subject: Re: drm-i915-mst + Ubuntu 14.04 + HP 840
Date: Fri, 7 Nov 2014 15:27:17 -0500 (EST) [thread overview]
Message-ID: <377205850.6947709.1415392037155.JavaMail.zimbra@redhat.com> (raw)
In-Reply-To: <xa1toasizsyz.fsf@mina86.com>
Just try a 3.17 based kernel if you can.
and make sure you have a new enough intel userspace driver.
Dave.
----- Original Message -----
> From: "Michal Nazarewicz" <mina86@mina86.com>
> To: airlied@redhat.com
> Cc: intel-gfx@lists.freedesktop.org
> Sent: Saturday, 8 November, 2014 5:55:00 AM
> Subject: drm-i915-mst + Ubuntu 14.04 + HP 840
>
> Hi Dave,
>
> I'm trying to get your drm-i915-mst-v3.16[1] branch applied on top of
> Ubuntu[2] kernel[3] to get HP's 840 notebook to handle two DPs port on
> the docking station but I'm hitting some problems with your patches. Or
> so I think.
>
> If I start and boot with the laptop connected to the docking station and
> the screens, I'm getting BUGs (full dmesg attached) and X refuses to
> start at all. E.g.:
>
> ------------------------ >8 ----------------------------------------
> [ 12.493151] [drm:intel_pipe_config_compare] *ERROR* mismatch in
> adjusted_mode.crtc_clock (expected 119000, found 0)
> [ 12.493171] WARNING: CPU: 0 PID: 61 at
> /home/mpn/code/linux/drivers/gpu/drm/i915/intel_display.c:10221
> check_crtc_state+0x235/0x350 [i915]()
>
> [ 12.503272] [drm:intel_pipe_config_compare] *ERROR* mismatch in
> adjusted_mode.crtc_clock (expected 119000, found 0)
> [ 12.503284] WARNING: CPU: 0 PID: 61 at
> /home/mpn/code/linux/drivers/gpu/drm/i915/intel_display.c:10221
> check_crtc_state+0x235/0x350 [i915]()
>
> [ 12.503449] [drm:intel_pipe_config_compare] *ERROR* mismatch in
> adjusted_mode.crtc_clock (expected 119000, found 0)
> [ 12.503460] WARNING: CPU: 0 PID: 61 at
> /home/mpn/code/linux/drivers/gpu/drm/i915/intel_display.c:10221
> check_crtc_state+0x235/0x350 [i915]()
> ------------------------ >8 ----------------------------------------
>
> If I boot up with laptop disconnected from the docking station and
> connect it later on, I'm getting the following errors:
>
> ------------------------ >8 ----------------------------------------
> [ 248.615216] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus
> alignment
> [ 248.629843] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus
> alignment
> [ 248.630412] acpi PNP0501:00: Still not present
> [ 252.261562] usb 3-1: new SuperSpeed USB device number 5 using xhci_hcd
> [ 252.277626] usb 3-1: New USB device found, idVendor=0424, idProduct=5534
> [ 252.277630] usb 3-1: New USB device strings: Mfr=2, Product=3,
> SerialNumber=0
> [ 252.277632] usb 3-1: Product: USB5534B
> [ 252.277633] usb 3-1: Manufacturer: SMSC
> [ 252.278047] hub 3-1:1.0: USB hub found
> [ 252.278067] hub 3-1:1.0: 4 ports detected
> [ 252.517255] usb 2-1: new high-speed USB device number 16 using xhci_hcd
> [ 252.645530] usb 2-1: New USB device found, idVendor=0424, idProduct=2134
> [ 252.645534] usb 2-1: New USB device strings: Mfr=1, Product=2,
> SerialNumber=0
> [ 252.645536] usb 2-1: Product: USB2134B
> [ 252.645538] usb 2-1: Manufacturer: SMSC
> [ 252.645970] hub 2-1:1.0: USB hub found
> [ 252.646024] hub 2-1:1.0: 4 ports detected
> [ 252.693505] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus
> alignment
> [ 252.704220] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus
> alignment
> [ 252.704478] acpi PNP0501:00: Still not present
> ------------------------ >8 ----------------------------------------
>
> Needless to say, “xrandr -q” did not detect any of the DisplayPort
> screens.
>
> I was wondering if you had any idea what could be a problem? Perhaps
> there is a newer version of your patchset that I should try?
>
> [1] http://cgit.freedesktop.org/~airlied/linux/log/?h=drm-i915-mst-v3.16
> [2] Which probably wouldn't by your choice of a distro. ;)
> [3]
> http://kernel.ubuntu.com/git?p=ubuntu/ubuntu-utopic.git;a=shortlog;h=refs/heads/master
>
> --
> Best regards, _ _
> .o. | Liege of Serenely Enlightened Majesty of o' \,=./ `o
> ..o | Computer Science, Michał “mina86” Nazarewicz (o o)
> ooo +--<mpn@google.com>--<xmpp:mina86@jabber.org>--ooO--(_)--Ooo--
>
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
next prev parent reply other threads:[~2014-11-07 20:27 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-11-07 19:55 drm-i915-mst + Ubuntu 14.04 + HP 840 Michal Nazarewicz
2014-11-07 20:27 ` David Airlie [this message]
2014-11-10 16:54 ` Michal Nazarewicz
2014-11-14 15:32 ` Michal Nazarewicz
2014-11-18 6:03 ` David Airlie
2014-12-03 17:52 ` Michal Nazarewicz
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=377205850.6947709.1415392037155.JavaMail.zimbra@redhat.com \
--to=airlied@redhat.com \
--cc=intel-gfx@lists.freedesktop.org \
--cc=mina86@mina86.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox