From: "Jindal, Sonika" <sonika.jindal@intel.com>
To: Jani Nikula <jani.nikula@intel.com>,
"dri-devel@lists.freedesktop.org"
<dri-devel@lists.freedesktop.org>
Cc: "intel-gfx@lists.freedesktop.org" <intel-gfx@lists.freedesktop.org>
Subject: Re: [PATCH v2] drm/dp: add DPCD definitions from eDP 1.4
Date: Fri, 27 Feb 2015 19:16:33 +0530 [thread overview]
Message-ID: <54F07539.7090909@intel.com> (raw)
In-Reply-To: <1425035474-27466-1-git-send-email-jani.nikula@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
On 2/27/2015 4:41 PM, Jani Nikula wrote:
> Add a number of DPCD definitions from eDP 1.4.
>
> v2: s/DP_ALPM_LOCK_TIMEOUT_ERROR_STATUS/DP_ALPM_LOCK_TIMEOUT_ERROR/
> (Sonika)
>
> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
> ---
> include/drm/drm_dp_helper.h | 37 +++++++++++++++++++++++++++++++++++++
> 1 file changed, 37 insertions(+)
>
> diff --git a/include/drm/drm_dp_helper.h b/include/drm/drm_dp_helper.h
> index 319d5edfb3b5..c5fdc2d3ca97 100644
> --- a/include/drm/drm_dp_helper.h
> +++ b/include/drm/drm_dp_helper.h
> @@ -168,10 +168,18 @@
> #define DP_AUD_DEL_INS2 0x02d
> /* End of AV_SYNC_DATA_BLOCK */
>
> +#define DP_RECEIVER_ALPM_CAP 0x02e /* eDP 1.4 */
> +# define DP_ALPM_CAP (1 << 0)
> +
> +#define DP_SINK_DEVICE_AUX_FRAME_SYNC_CAP 0x02f /* eDP 1.4 */
> +# define DP_AUX_FRAME_SYNC_CAP (1 << 0)
> +
> #define DP_GUID 0x030 /* 1.2 */
>
> #define DP_PSR_SUPPORT 0x070 /* XXX 1.2? */
> # define DP_PSR_IS_SUPPORTED 1
> +# define DP_PSR2_IS_SUPPORTED 2 /* eDP 1.4 */
> +
> #define DP_PSR_CAPS 0x071 /* XXX 1.2? */
> # define DP_PSR_NO_TRAIN_ON_EXIT 1
> # define DP_PSR_SETUP_TIME_330 (0 << 1)
> @@ -211,6 +219,7 @@
>
> /* link configuration */
> #define DP_LINK_BW_SET 0x100
> +# define DP_LINK_RATE_TABLE 0x00 /* eDP 1.4 */
> # define DP_LINK_BW_1_62 0x06
> # define DP_LINK_BW_2_7 0x0a
> # define DP_LINK_BW_5_4 0x14 /* 1.2 */
> @@ -307,15 +316,30 @@
> #define DP_AUDIO_DELAY2 0x114
>
> #define DP_LINK_RATE_SET 0x115 /* eDP 1.4 */
> +# define DP_LINK_RATE_SET_SHIFT 0
> +# define DP_LINK_RATE_SET_MASK (7 << 0)
> +
> +#define DP_RECEIVER_ALPM_CONFIG 0x116 /* eDP 1.4 */
> +# define DP_ALPM_ENABLE (1 << 0)
> +# define DP_ALPM_LOCK_ERROR_IRQ_HPD_ENABLE (1 << 1)
> +
> +#define DP_SINK_DEVICE_AUX_FRAME_SYNC_CONF 0x117 /* eDP 1.4 */
> +# define DP_AUX_FRAME_SYNC_ENABLE (1 << 0)
> +# define DP_IRQ_HPD_ENABLE (1 << 1)
>
> #define DP_UPSTREAM_DEVICE_DP_PWR_NEED 0x118 /* 1.2 */
> # define DP_PWR_NOT_NEEDED (1 << 0)
>
> +#define DP_AUX_FRAME_SYNC_VALUE 0x15c /* eDP 1.4 */
> +# define DP_AUX_FRAME_SYNC_VALID (1 << 0)
> +
> #define DP_PSR_EN_CFG 0x170 /* XXX 1.2? */
> # define DP_PSR_ENABLE (1 << 0)
> # define DP_PSR_MAIN_LINK_ACTIVE (1 << 1)
> # define DP_PSR_CRC_VERIFICATION (1 << 2)
> # define DP_PSR_FRAME_CAPTURE (1 << 3)
> +# define DP_PSR_SELECTIVE_UPDATE (1 << 4)
> +# define DP_PSR_IRQ_HPD_WITH_CRC_ERRORS (1 << 5)
>
> #define DP_ADAPTER_CTRL 0x1a0
> # define DP_ADAPTER_CTRL_FORCE_LOAD_SENSE (1 << 0)
> @@ -423,6 +447,10 @@
> # define DP_SET_POWER_MASK 0x3
>
> #define DP_EDP_DPCD_REV 0x700 /* eDP 1.2 */
> +# define DP_EDP_11 0x00
> +# define DP_EDP_12 0x01
> +# define DP_EDP_13 0x02
> +# define DP_EDP_14 0x03
>
> #define DP_EDP_GENERAL_CAP_1 0x701
>
> @@ -430,6 +458,8 @@
>
> #define DP_EDP_GENERAL_CAP_2 0x703
>
> +#define DP_EDP_GENERAL_CAP_3 0x704 /* eDP 1.4 */
> +
> #define DP_EDP_DISPLAY_CONTROL_REGISTER 0x720
>
> #define DP_EDP_BACKLIGHT_MODE_SET_REGISTER 0x721
> @@ -456,6 +486,9 @@
> #define DP_EDP_DBC_MINIMUM_BRIGHTNESS_SET 0x732
> #define DP_EDP_DBC_MAXIMUM_BRIGHTNESS_SET 0x733
>
> +#define DP_EDP_REGIONAL_BACKLIGHT_BASE 0x740 /* eDP 1.4 */
> +#define DP_EDP_REGIONAL_BACKLIGHT_0 0x741 /* eDP 1.4 */
> +
> #define DP_SIDEBAND_MSG_DOWN_REQ_BASE 0x1000 /* 1.2 MST */
> #define DP_SIDEBAND_MSG_UP_REP_BASE 0x1200 /* 1.2 MST */
> #define DP_SIDEBAND_MSG_DOWN_REP_BASE 0x1400 /* 1.2 MST */
> @@ -474,6 +507,7 @@
> #define DP_PSR_ERROR_STATUS 0x2006 /* XXX 1.2? */
> # define DP_PSR_LINK_CRC_ERROR (1 << 0)
> # define DP_PSR_RFB_STORAGE_ERROR (1 << 1)
> +# define DP_PSR_VSC_SDP_UNCORRECTABLE_ERROR (1 << 2) /* eDP 1.4 */
>
> #define DP_PSR_ESI 0x2007 /* XXX 1.2? */
> # define DP_PSR_CAPS_CHANGE (1 << 0)
> @@ -487,6 +521,9 @@
> # define DP_PSR_SINK_INTERNAL_ERROR 7
> # define DP_PSR_SINK_STATE_MASK 0x07
>
> +#define DP_RECEIVER_ALPM_STATUS 0x200b /* eDP 1.4 */
> +# define DP_ALPM_LOCK_TIMEOUT_ERROR (1 << 0)
> +
> /* DP 1.2 Sideband message defines */
> /* peer device type - DP 1.2a Table 2-92 */
> #define DP_PEER_DEVICE_NONE 0x0
>
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
http://lists.freedesktop.org/mailman/listinfo/dri-devel
next prev parent reply other threads:[~2015-02-27 13:46 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-02-25 12:46 [PATCH 1/4] drm/dp: indentation and ordering cleanups Jani Nikula
2015-02-25 12:46 ` [PATCH 2/4] drm/dp: add DPCD definitions from DP 1.2a Jani Nikula
2015-02-26 9:52 ` sonika
2015-02-25 12:46 ` [PATCH 3/4] drm/dp: add DPCD definitions from eDP 1.2 Jani Nikula
2015-02-26 9:51 ` sonika
2015-02-26 13:23 ` [Intel-gfx] " Daniel Vetter
2015-02-25 12:46 ` [PATCH 4/4] drm/dp: add DPCD definitions from eDP 1.4 Jani Nikula
2015-02-26 11:58 ` sonika
2015-02-26 12:37 ` Jani Nikula
2015-02-27 11:10 ` [PATCH v2] drm/dp: add DPCD definitions from DP 1.1 and 1.2a Jani Nikula
2015-02-27 11:12 ` Jani Nikula
2015-02-27 13:10 ` Daniel Vetter
2015-03-03 2:18 ` shuang.he
2015-02-27 11:11 ` [PATCH v2] drm/dp: add DPCD definitions from eDP 1.4 Jani Nikula
2015-02-27 13:46 ` Jindal, Sonika [this message]
2015-02-27 19:47 ` [PATCH 4/4] " shuang.he
2015-02-26 9:51 ` [PATCH 1/4] drm/dp: indentation and ordering cleanups sonika
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=54F07539.7090909@intel.com \
--to=sonika.jindal@intel.com \
--cc=dri-devel@lists.freedesktop.org \
--cc=intel-gfx@lists.freedesktop.org \
--cc=jani.nikula@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox