From: "Jindal, Sonika" <sonika.jindal@intel.com>
To: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Subject: Re: [PATCH] drm/i915/bxt: WA for swapped HPD pins in A stepping
Date: Wed, 22 Jul 2015 16:39:42 +0530 [thread overview]
Message-ID: <55AF79F6.7050205@intel.com> (raw)
In-Reply-To: <55AF7161.70804@intel.com>
On 7/22/2015 4:03 PM, Sivakumar Thulasimani wrote:
>
>
> On 7/22/2015 3:37 PM, Sonika Jindal wrote:
>> As per bspec, on BXT A0/A1, sw needs to activate DDIA HPD logic
>> and interrupts to check the external panel connection and DDIC HPD
>> logic for edp panel.
>>
>> v2: For DP, irq_port is used to determine the encoder instead of
>> hpd_pin and removing the edp HPD logic because port A HPD is not
>> present(Imre)
>> v3: Rebased on top of Imre's patchset for enabling HPD on PORT A.
>> Added hpd_pin swapping for intel_dp_init_connector, setting encoder
>> for PORT_A as per the WA in irq_port (Imre)
>>
>> Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
>> ---
>> drivers/gpu/drm/i915/intel_ddi.c | 12 +++++++++++-
>> drivers/gpu/drm/i915/intel_dp.c | 4 ++++
>> drivers/gpu/drm/i915/intel_hdmi.c | 9 ++++++++-
>> 3 files changed, 23 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/gpu/drm/i915/intel_ddi.c
>> b/drivers/gpu/drm/i915/intel_ddi.c
>> index e2c6f73..d5745e2 100644
>> --- a/drivers/gpu/drm/i915/intel_ddi.c
>> +++ b/drivers/gpu/drm/i915/intel_ddi.c
>> @@ -3225,7 +3225,17 @@ void intel_ddi_init(struct drm_device *dev,
>> enum port port)
>> goto err;
>> intel_dig_port->hpd_pulse = intel_dp_hpd_pulse;
>> - dev_priv->hotplug.irq_port[port] = intel_dig_port;
>> + /*
>> + * On BXT A0/A1, sw needs to activate DDIA HPD logic and
>> + * interrupts to check the external panel connection.
>> + */
>> + if (IS_BROXTON(dev_priv) && (INTEL_REVID(dev) < BXT_REVID_B0)) {
>> + if (port == PORT_B)
>> + dev_priv->hotplug.irq_port[PORT_A] = intel_dig_port;
>> + else if (port == PORT_A)
>> + dev_priv->hotplug.irq_port[PORT_C] = intel_dig_port;
>> + } else
>> + dev_priv->hotplug.irq_port[port] = intel_dig_port;
>> }
>> /* In theory we don't need the encoder->type check, but leave it
>> just in
>> diff --git a/drivers/gpu/drm/i915/intel_dp.c
>> b/drivers/gpu/drm/i915/intel_dp.c
>> index fcc64e5..71679ef 100644
>> --- a/drivers/gpu/drm/i915/intel_dp.c
>> +++ b/drivers/gpu/drm/i915/intel_dp.c
>> @@ -5785,9 +5785,13 @@ intel_dp_init_connector(struct
>> intel_digital_port *intel_dig_port,
>> switch (port) {
>> case PORT_A:
>> intel_encoder->hpd_pin = HPD_PORT_A;
>> + if (IS_BROXTON(dev_priv) && (INTEL_REVID(dev) < BXT_REVID_B0))
>> + intel_encoder->hpd_pin = HPD_PORT_C;
>> break;
>> case PORT_B:
>> intel_encoder->hpd_pin = HPD_PORT_B;
>> + if (IS_BROXTON(dev_priv) && (INTEL_REVID(dev) < BXT_REVID_B0))
>> + intel_encoder->hpd_pin = HPD_PORT_A;
>> break;
>> case PORT_C:
>> intel_encoder->hpd_pin = HPD_PORT_C;
>> diff --git a/drivers/gpu/drm/i915/intel_hdmi.c
>> b/drivers/gpu/drm/i915/intel_hdmi.c
>> index 70bad5b..94fa716 100644
>> --- a/drivers/gpu/drm/i915/intel_hdmi.c
>> +++ b/drivers/gpu/drm/i915/intel_hdmi.c
>> @@ -1973,7 +1973,14 @@ void intel_hdmi_init_connector(struct
>> intel_digital_port *intel_dig_port,
>> intel_hdmi->ddc_bus = GMBUS_PIN_1_BXT;
>> else
>> intel_hdmi->ddc_bus = GMBUS_PIN_DPB;
>> - intel_encoder->hpd_pin = HPD_PORT_B;
>> + /*
>> + * On BXT A0/A1, sw needs to activate DDIA HPD logic and
>> + * interrupts to check the external panel connection.
>> + */
>> + if (IS_BROXTON(dev_priv) && (INTEL_REVID(dev) < BXT_REVID_B0))
>> + intel_encoder->hpd_pin = HPD_PORT_A;
>> + else
>> + intel_encoder->hpd_pin = HPD_PORT_B;
>> break;
>> case PORT_C:
>> if (IS_BROXTON(dev_priv))
> bxt_hpd_irq_setup is not touched here without this being updated i dont
> think HPD can be enabled.
Now, we swap the hpd_pin, which is being used to enable HPD in
bxt_hpd_irq_setup.
Regards,
Sonika
>
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
next prev parent reply other threads:[~2015-07-22 11:09 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-07-13 4:17 [PATCH] drm/i915/bxt: WA for swapped HPD pins in A stepping Sonika Jindal
2015-07-13 6:31 ` Sivakumar Thulasimani
2015-07-13 8:11 ` Jindal, Sonika
2015-07-13 8:40 ` Sonika Jindal
2015-07-13 9:40 ` Daniel Vetter
2015-07-13 10:57 ` Sivakumar Thulasimani
2015-07-14 5:48 ` [PATCH 1/2] drm/i915/bxt: Add HPD support for DDIA Sonika Jindal
2015-07-14 5:48 ` [PATCH 2/2] drm/i915/bxt: WA for swapped HPD pins in A stepping Sonika Jindal
2015-07-14 8:10 ` Daniel Vetter
2015-07-14 14:22 ` Imre Deak
2015-07-15 6:35 ` Jindal, Sonika
2015-07-15 8:04 ` Jindal, Sonika
2015-07-15 9:07 ` Daniel Vetter
2015-07-17 4:29 ` Jindal, Sonika
2015-07-17 8:17 ` [PATCH] " Sonika Jindal
2015-07-17 23:47 ` Imre Deak
2015-07-20 6:06 ` Jindal, Sonika
2015-07-20 21:43 ` Imre Deak
2015-07-22 10:07 ` Sonika Jindal
2015-07-22 10:33 ` Sivakumar Thulasimani
2015-07-22 11:09 ` Jindal, Sonika [this message]
2015-07-22 11:31 ` Sivakumar Thulasimani
2015-07-22 12:02 ` Jindal, Sonika
2015-07-22 12:20 ` Sivakumar Thulasimani
2015-07-27 5:32 ` Sonika Jindal
2015-07-27 11:46 ` Sivakumar Thulasimani
2015-07-28 8:42 ` shuang.he
2015-08-05 9:53 ` Imre Deak
2015-08-05 10:11 ` Sivakumar Thulasimani
2015-07-20 5:07 ` shuang.he
2015-07-13 8:26 ` shuang.he
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=55AF79F6.7050205@intel.com \
--to=sonika.jindal@intel.com \
--cc=intel-gfx@lists.freedesktop.org \
--cc=sivakumar.thulasimani@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox