public inbox for intel-gfx@lists.freedesktop.org
 help / color / mirror / Atom feed
From: Jani Nikula <jani.nikula@linux.intel.com>
To: ville.syrjala@linux.intel.com, intel-gfx@lists.freedesktop.org
Subject: Re: [PATCH 05/13] drm/i915: Use ilk_max_pixel_rate() for	BXT cdclk calculation
Date: Thu, 12 May 2016 13:13:47 +0300	[thread overview]
Message-ID: <87shxnh9d0.fsf@intel.com> (raw)
In-Reply-To: <1462995892-32416-6-git-send-email-ville.syrjala@linux.intel.com>

On Wed, 11 May 2016, ville.syrjala@linux.intel.com wrote:
> From: Ville Syrjälä <ville.syrjala@linux.intel.com>
>
> BXT uses the "pch" panel fitter configuration, so we can use
> ilk_max_pixel_rate() instead of intel_mode_max_pixclk() to compute the
> pipe pixel rate. ilk_max_pixel_rate() will account for the pipe
> scaler downscaling factor whereas intel_mode_max_pixclk() will not.
>
> I'm pretty sure the same limitation is there on GMCH platforms, but
> no one just bothered to implement the downscaling adjustment for them.
> Probably should just unify the panel fitter setup more across the
> platforms and use the exact same code on all platforms for this.
> But in the meantime, let's at least make BXT a bit more correct.
>
> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

Reviewed-by: Jani Nikula <jani.nikula@intel.com>


> ---
>  drivers/gpu/drm/i915/intel_display.c | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
> index deeaf3ba1dee..fd55112f266d 100644
> --- a/drivers/gpu/drm/i915/intel_display.c
> +++ b/drivers/gpu/drm/i915/intel_display.c
> @@ -117,6 +117,7 @@ static void ironlake_pfit_disable(struct intel_crtc *crtc, bool force);
>  static void ironlake_pfit_enable(struct intel_crtc *crtc);
>  static void intel_modeset_setup_hw_state(struct drm_device *dev);
>  static void intel_pre_disable_primary_noatomic(struct drm_crtc *crtc);
> +static int ilk_max_pixel_rate(struct drm_atomic_state *state);
>  
>  typedef struct {
>  	int	min, max;
> @@ -5967,8 +5968,7 @@ static int valleyview_modeset_calc_cdclk(struct drm_atomic_state *state)
>  
>  static int broxton_modeset_calc_cdclk(struct drm_atomic_state *state)
>  {
> -	struct drm_device *dev = state->dev;
> -	int max_pixclk = intel_mode_max_pixclk(dev, state);
> +	int max_pixclk = ilk_max_pixel_rate(state);
>  	struct intel_atomic_state *intel_state =
>  		to_intel_atomic_state(state);

-- 
Jani Nikula, Intel Open Source Technology Center
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

  reply	other threads:[~2016-05-12 10:13 UTC|newest]

Thread overview: 30+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-05-11 19:44 [PATCH 00/13] drm/i915: cdclk code cleanup ville.syrjala
2016-05-11 19:44 ` [PATCH 01/13] drm/i915: Drop checks for max_pixclk failures in cdclk computation ville.syrjala
2016-05-12 10:02   ` Jani Nikula
2016-05-11 19:44 ` [PATCH 02/13] drm/i915: Extract broadwell_calc_cdclk() ville.syrjala
2016-05-12 10:03   ` Jani Nikula
2016-05-11 19:44 ` [PATCH 03/13] drm/i915: Untangle .fdi_link_train and cdclk vfunc setup ville.syrjala
2016-05-12 10:06   ` Jani Nikula
2016-05-11 19:44 ` [PATCH 04/13] drm/i915: Don't pass dev_priv to broxton_calc_cdclk() ville.syrjala
2016-05-12 10:07   ` Jani Nikula
2016-05-11 19:44 ` [PATCH 05/13] drm/i915: Use ilk_max_pixel_rate() for BXT cdclk calculation ville.syrjala
2016-05-12 10:13   ` Jani Nikula [this message]
2016-05-11 19:44 ` [PATCH 06/13] drm/i915: Use skl_cdclk_decimal() on bxt ville.syrjala
2016-05-12 10:23   ` Jani Nikula
2016-05-11 19:44 ` [PATCH 07/13] drm/i915: Remove 10% cdclk guardband on BXT ville.syrjala
2016-05-12 16:42   ` Imre Deak
2016-05-11 19:44 ` [PATCH 08/13] drm/i915: Extract skl_dpll0_disable() ville.syrjala
2016-05-12 10:25   ` Jani Nikula
2016-05-11 19:44 ` [PATCH 09/13] drm/i915: Kill off dead code from skl_dpll0_enable() ville.syrjala
2016-05-12 10:26   ` Jani Nikula
2016-05-11 19:44 ` [PATCH 10/13] drm/i915: s/freq/cdclk/ ville.syrjala
2016-05-12 10:28   ` Jani Nikula
2016-05-11 19:44 ` [PATCH 11/13] drm/i915: s/required_vco/vco/ in skl cdclk code ville.syrjala
2016-05-12 10:29   ` Jani Nikula
2016-05-11 19:44 ` [PATCH 12/13] drm/i915: Program BXT_CDCLK_CD2X_PIPE ville.syrjala
2016-05-12 16:58   ` Imre Deak
2016-05-11 19:44 ` [PATCH 13/13] drm/i915: Eliminate the CDCLK_CTL RMW on BXT ville.syrjala
2016-05-12 17:05   ` Imre Deak
2016-05-11 20:23 ` ✗ Ro.CI.BAT: failure for drm/i915: cdclk code cleanup Patchwork
2016-05-12 15:16   ` Ville Syrjälä
2016-05-13 18:42 ` [PATCH 00/13] " Ville Syrjälä

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=87shxnh9d0.fsf@intel.com \
    --to=jani.nikula@linux.intel.com \
    --cc=intel-gfx@lists.freedesktop.org \
    --cc=ville.syrjala@linux.intel.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox