From mboxrd@z Thu Jan 1 00:00:00 1970 From: Neftin, Sasha Date: Thu, 31 Jan 2019 10:37:01 +0200 Subject: [Intel-wired-lan] [PATCH] e1000e: fix cyclic resets at link up with active tx In-Reply-To: <7198a11f-8b3b-f7c2-a263-3e103ad32a70@intel.com> References: <154747257030.250168.12931902291381446144.stgit@buzz> <031e1689-e133-5398-ad00-8f45f679ffff@intel.com> <942e559e-32ee-9e05-1489-823662d0dfe9@yandex-team.ru> <7198a11f-8b3b-f7c2-a263-3e103ad32a70@intel.com> Message-ID: <4ae57d83-4e21-8733-8e54-240ca76ff5fc@intel.com> MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: intel-wired-lan@osuosl.org List-ID: On 1/20/2019 12:09, Neftin, Sasha wrote: > On 1/17/2019 14:10, Konstantin Khlebnikov wrote: >> >> >> On 17.01.2019 10:57, Neftin, Sasha wrote: >>> On 1/14/2019 15:29, Konstantin Khlebnikov wrote: >>>> I'm seeing series of e1000e resets (sometimes endless) at system boot >>>> if something generates tx traffic at this time. In my case this is >>>> netconsole who sends message "e1000e 0000:02:00.0: Some CPU C-states >>>> have been disabled in order to enable jumbo frames" from e1000e itself. >>>> As result e1000_watchdog_task sees used tx buffer while carrier is off >>>> and start this reset cycle again. >>>> >>>> [?? 17.794359] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, >>>> Flow Control: None >>>> [?? 17.794714] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready >>>> [?? 22.936455] e1000e 0000:02:00.0 eth1: changing MTU from 1500 to 9000 >>>> [?? 23.033336] e1000e 0000:02:00.0: Some CPU C-states have been >>>> disabled in order to enable jumbo frames >>>> [?? 26.102364] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, >>>> Flow Control: None >>>> [?? 27.174495] 8021q: 802.1Q VLAN Support v1.8 >>>> [?? 27.174513] 8021q: adding VLAN 0 to HW filter on device eth1 >>>> [?? 30.671724] cgroup: cgroup: disabling cgroup2 socket matching due >>>> to net_prio or net_cls activation >>>> [?? 30.898564] netpoll: netconsole: local port 6666 >>>> [?? 30.898566] netpoll: netconsole: local IPv6 address >>>> 2a02:6b8:0:80b:beae:c5ff:fe28:23f8 >>>> [?? 30.898567] netpoll: netconsole: interface 'eth1' >>>> [?? 30.898568] netpoll: netconsole: remote port 6666 >>>> [?? 30.898568] netpoll: netconsole: remote IPv6 address >>>> 2a02:6b8:b000:605c:e61d:2dff:fe03:3790 >>>> [?? 30.898569] netpoll: netconsole: remote ethernet address >>>> b0:a8:6e:f4:ff:c0 >>>> [?? 30.917747] console [netcon0] enabled >>>> [?? 30.917749] netconsole: network logging started >>>> [?? 31.453353] e1000e 0000:02:00.0: Some CPU C-states have been >>>> disabled in order to enable jumbo frames >>>> [?? 34.185730] e1000e 0000:02:00.0: Some CPU C-states have been >>>> disabled in order to enable jumbo frames >>>> [?? 34.321840] e1000e 0000:02:00.0: Some CPU C-states have been >>>> disabled in order to enable jumbo frames >>>> [?? 34.465822] e1000e 0000:02:00.0: Some CPU C-states have been >>>> disabled in order to enable jumbo frames >>>> [?? 34.597423] e1000e 0000:02:00.0: Some CPU C-states have been >>>> disabled in order to enable jumbo frames >>>> [?? 34.745417] e1000e 0000:02:00.0: Some CPU C-states have been >>>> disabled in order to enable jumbo frames >>>> [?? 34.877356] e1000e 0000:02:00.0: Some CPU C-states have been >>>> disabled in order to enable jumbo frames >>>> [?? 35.005441] e1000e 0000:02:00.0: Some CPU C-states have been >>>> disabled in order to enable jumbo frames >>>> [?? 35.157376] e1000e 0000:02:00.0: Some CPU C-states have been >>>> disabled in order to enable jumbo frames >>>> [?? 35.289362] e1000e 0000:02:00.0: Some CPU C-states have been >>>> disabled in order to enable jumbo frames >>>> [?? 35.417441] e1000e 0000:02:00.0: Some CPU C-states have been >>>> disabled in order to enable jumbo frames >>>> [?? 37.790342] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, >>>> Flow Control: None >>>> >>>> This patch flushes tx buffers only once when carrier is off >>>> rather than at each watchdog iteration. >>>> >>>> Signed-off-by: Konstantin Khlebnikov >>>> --- >>>> ? drivers/net/ethernet/intel/e1000e/netdev.c |?? 15 ++++++--------- >>>> ? 1 file changed, 6 insertions(+), 9 deletions(-) >>>> >>>> diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c >>>> b/drivers/net/ethernet/intel/e1000e/netdev.c >>>> index 189f231075c2..d10083beec83 100644 >>>> --- a/drivers/net/ethernet/intel/e1000e/netdev.c >>>> +++ b/drivers/net/ethernet/intel/e1000e/netdev.c >>>> @@ -5309,8 +5309,13 @@ static void e1000_watchdog_task(struct >>>> work_struct *work) >>>> ????????????? /* 8000ES2LAN requires a Rx packet buffer work-around >>>> ?????????????? * on link down event; reset the controller to flush >>>> ?????????????? * the Rx packet buffer. >>>> +???????????? * >>>> +???????????? * If the link is lost the controller stops DMA, but >>>> +???????????? * if there is queued Tx work it cannot be done.? So >>>> +???????????? * reset the controller to flush the Tx packet buffers. >>>> ?????????????? */ >>>> -??????????? if (adapter->flags & FLAG_RX_NEEDS_RESTART) >>>> +??????????? if ((adapter->flags & FLAG_RX_NEEDS_RESTART) || >>>> +??????????????? e1000_desc_unused(tx_ring) + 1 < tx_ring->count) >>>> ????????????????? adapter->flags |= FLAG_RESTART_NOW; >>>> ????????????? else >>>> ????????????????? pm_schedule_suspend(netdev->dev.parent, >>>> @@ -5333,14 +5338,6 @@ static void e1000_watchdog_task(struct >>>> work_struct *work) >>>> ????? adapter->gotc_old = adapter->stats.gotc; >>>> ????? spin_unlock(&adapter->stats64_lock); >>>> -??? /* If the link is lost the controller stops DMA, but >>>> -???? * if there is queued Tx work it cannot be done.? So >>>> -???? * reset the controller to flush the Tx packet buffers. >>>> -???? */ >>>> -??? if (!netif_carrier_ok(netdev) && >>>> -??????? (e1000_desc_unused(tx_ring) + 1 < tx_ring->count)) >>>> -??????? adapter->flags |= FLAG_RESTART_NOW; >>>> - >>>> ????? /* If reset is necessary, do it outside of interrupt context. */ >>>> ????? if (adapter->flags & FLAG_RESTART_NOW) { >>>> ????????? schedule_work(&adapter->reset_task); >>>> >>>> _______________________________________________ >>>> Intel-wired-lan mailing list >>>> Intel-wired-lan at osuosl.org >>>> https://lists.osuosl.org/mailman/listinfo/intel-wired-lan >>>> >>> What is the HW setup you encountered this issue? Could you try to >>> disable the jumbo frame and recheck? We cannot allow the low CPU >>> states when the jumbo feature is enabled. This is HW design. >>> We will try to review this patch next week. Please, be patient. >> >> Without jumbo frames there will be no message about disabled c-states. >> Thus tx queue will be likely empty and nothing will trigger that >> cyclic restart. >> > That I thought. Ok. Let's us finish the validation. If everything is > okay we will pick up the patch. No objection. In case this patch pass next-queue test let's pick up. >> Sequence might depend on uplink switch reaction - how fast carrier >> signal appears. >> >> >> $ lscpu >> Architecture:????????? x86_64 >> CPU op-mode(s):??????? 32-bit, 64-bit >> Byte Order:??????????? Little Endian >> CPU(s):??????????????? 24 >> On-line CPU(s) list:?? 0-23 >> Thread(s) per core:??? 2 >> Core(s) per socket:??? 6 >> Socket(s):???????????? 2 >> NUMA node(s):????????? 2 >> Vendor ID:???????????? GenuineIntel >> CPU family:??????????? 6 >> Model:???????????????? 44 >> Model name:??????????? Intel(R) Xeon(R) CPU?????????? E5645? @ 2.40GHz >> Stepping:????????????? 2 >> CPU MHz:?????????????? 1600.037 >> BogoMIPS:????????????? 4800.19 >> Virtualization:??????? VT-x >> L1d cache:???????????? 32K >> L1i cache:???????????? 32K >> L2 cache:????????????? 256K >> L3 cache:????????????? 12288K >> NUMA node0 CPU(s):???? 0-5,12-17 >> NUMA node1 CPU(s):???? 6-11,18-23 >> Flags:???????????????? fpu vme de pse tsc msr pae mce cx8 apic sep >> mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht >> tm pbe syscall nx pdpe1gb rdtscp lm constant_tsc arch_perfmon pebs bts >> rep_good nopl xtopology nonstop_tsc cpuid aperfmperf pni pclmulqdq >> dtes64 monitor ds_cpl vmx smx est tm2 ssse3 cx16 xtpr pdcm pcid dca >> sse4_1 sse4_2 popcnt aes lahf_lm epb tpr_shadow vnmi flexpriority ept >> vpid dtherm ida arat >> >> >> $ lspci >> 00:00.0 Host bridge: Intel Corporation 5500 I/O Hub to ESI Port (rev 22) >> 00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI >> Express Root Port 1 (rev 22) >> 00:02.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI >> Express Root Port 2 (rev 22) >> 00:03.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI >> Express Root Port 3 (rev 22) >> 00:07.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI >> Express Root Port 7 (rev 22) >> 00:08.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI >> Express Root Port 8 (rev 22) >> 00:09.0 PCI bridge: Intel Corporation 7500/5520/5500/X58 I/O Hub PCI >> Express Root Port 9 (rev 22) >> 00:0a.0 PCI bridge: Intel Corporation 7500/5520/5500/X58 I/O Hub PCI >> Express Root Port 10 (rev 22) >> 00:10.0 PIC: Intel Corporation 7500/5520/5500/X58 Physical and Link >> Layer Registers Port 0 (rev 22) >> 00:10.1 PIC: Intel Corporation 7500/5520/5500/X58 Routing and Protocol >> Layer Registers Port 0 (rev 22) >> 00:11.0 PIC: Intel Corporation 7500/5520/5500 Physical and Link Layer >> Registers Port 1 (rev 22) >> 00:11.1 PIC: Intel Corporation 7500/5520/5500 Routing & Protocol Layer >> Register Port 1 (rev 22) >> 00:14.0 PIC: Intel Corporation 7500/5520/5500/X58 I/O Hub System >> Management Registers (rev 22) >> 00:14.1 PIC: Intel Corporation 7500/5520/5500/X58 I/O Hub GPIO and >> Scratch Pad Registers (rev 22) >> 00:14.2 PIC: Intel Corporation 7500/5520/5500/X58 I/O Hub Control >> Status and RAS Registers (rev 22) >> 00:14.3 PIC: Intel Corporation 7500/5520/5500/X58 I/O Hub Throttle >> Registers (rev 22) >> 00:16.0 System peripheral: Intel Corporation 5520/5500/X58 Chipset >> QuickData Technology Device (rev 22) >> 00:16.1 System peripheral: Intel Corporation 5520/5500/X58 Chipset >> QuickData Technology Device (rev 22) >> 00:16.2 System peripheral: Intel Corporation 5520/5500/X58 Chipset >> QuickData Technology Device (rev 22) >> 00:16.3 System peripheral: Intel Corporation 5520/5500/X58 Chipset >> QuickData Technology Device (rev 22) >> 00:16.4 System peripheral: Intel Corporation 5520/5500/X58 Chipset >> QuickData Technology Device (rev 22) >> 00:16.5 System peripheral: Intel Corporation 5520/5500/X58 Chipset >> QuickData Technology Device (rev 22) >> 00:16.6 System peripheral: Intel Corporation 5520/5500/X58 Chipset >> QuickData Technology Device (rev 22) >> 00:16.7 System peripheral: Intel Corporation 5520/5500/X58 Chipset >> QuickData Technology Device (rev 22) >> 00:1a.0 USB controller: Intel Corporation 82801JI (ICH10 Family) USB >> UHCI Controller #4 >> 00:1a.1 USB controller: Intel Corporation 82801JI (ICH10 Family) USB >> UHCI Controller #5 >> 00:1a.7 USB controller: Intel Corporation 82801JI (ICH10 Family) USB2 >> EHCI Controller #2 >> 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI >> Express Root Port 1 >> 00:1c.4 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI >> Express Root Port 5 >> 00:1c.5 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI >> Express Root Port 6 >> 00:1d.0 USB controller: Intel Corporation 82801JI (ICH10 Family) USB >> UHCI Controller #1 >> 00:1d.1 USB controller: Intel Corporation 82801JI (ICH10 Family) USB >> UHCI Controller #2 >> 00:1d.2 USB controller: Intel Corporation 82801JI (ICH10 Family) USB >> UHCI Controller #3 >> 00:1d.3 USB controller: Intel Corporation 82801JI (ICH10 Family) USB >> UHCI Controller #6 >> 00:1d.7 USB controller: Intel Corporation 82801JI (ICH10 Family) USB2 >> EHCI Controller #1 >> 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) >> 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface >> Controller >> 00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA >> AHCI Controller >> 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller >> 01:01.0 VGA compatible controller: ASPEED Technology, Inc. ASPEED >> Graphics Family (rev 10) >> 02:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network >> Connection >> 03:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network >> Connection >> fe:00.0 Host bridge: Intel Corporation Xeon 5600 Series QuickPath >> Architecture Generic Non-core Registers (rev 02) >> fe:00.1 Host bridge: Intel Corporation Xeon 5600 Series QuickPath >> Architecture System Address Decoder (rev 02) >> fe:02.0 Host bridge: Intel Corporation Xeon 5600 Series QPI Link 0 >> (rev 02) >> fe:02.1 Host bridge: Intel Corporation Xeon 5600 Series QPI Physical 0 >> (rev 02) >> fe:02.2 Host bridge: Intel Corporation Xeon 5600 Series Mirror Port >> Link 0 (rev 02) >> fe:02.3 Host bridge: Intel Corporation Xeon 5600 Series Mirror Port >> Link 1 (rev 02) >> fe:02.4 Host bridge: Intel Corporation Xeon 5600 Series QPI Link 1 >> (rev 02) >> fe:02.5 Host bridge: Intel Corporation Xeon 5600 Series QPI Physical 1 >> (rev 02) >> fe:03.0 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Registers (rev 02) >> fe:03.1 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Target Address Decoder (rev 02) >> fe:03.2 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller RAS Registers (rev 02) >> fe:03.4 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Test Registers (rev 02) >> fe:04.0 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 0 Control (rev 02) >> fe:04.1 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 0 Address (rev 02) >> fe:04.2 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 0 Rank (rev 02) >> fe:04.3 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 0 Thermal Control (rev 02) >> fe:05.0 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 1 Control (rev 02) >> fe:05.1 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 1 Address (rev 02) >> fe:05.2 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 1 Rank (rev 02) >> fe:05.3 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 1 Thermal Control (rev 02) >> fe:06.0 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 2 Control (rev 02) >> fe:06.1 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 2 Address (rev 02) >> fe:06.2 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 2 Rank (rev 02) >> fe:06.3 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 2 Thermal Control (rev 02) >> ff:00.0 Host bridge: Intel Corporation Xeon 5600 Series QuickPath >> Architecture Generic Non-core Registers (rev 02) >> ff:00.1 Host bridge: Intel Corporation Xeon 5600 Series QuickPath >> Architecture System Address Decoder (rev 02) >> ff:02.0 Host bridge: Intel Corporation Xeon 5600 Series QPI Link 0 >> (rev 02) >> ff:02.1 Host bridge: Intel Corporation Xeon 5600 Series QPI Physical 0 >> (rev 02) >> ff:02.2 Host bridge: Intel Corporation Xeon 5600 Series Mirror Port >> Link 0 (rev 02) >> ff:02.3 Host bridge: Intel Corporation Xeon 5600 Series Mirror Port >> Link 1 (rev 02) >> ff:02.4 Host bridge: Intel Corporation Xeon 5600 Series QPI Link 1 >> (rev 02) >> ff:02.5 Host bridge: Intel Corporation Xeon 5600 Series QPI Physical 1 >> (rev 02) >> ff:03.0 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Registers (rev 02) >> ff:03.1 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Target Address Decoder (rev 02) >> ff:03.2 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller RAS Registers (rev 02) >> ff:03.4 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Test Registers (rev 02) >> ff:04.0 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 0 Control (rev 02) >> ff:04.1 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 0 Address (rev 02) >> ff:04.2 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 0 Rank (rev 02) >> ff:04.3 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 0 Thermal Control (rev 02) >> ff:05.0 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 1 Control (rev 02) >> ff:05.1 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 1 Address (rev 02) >> ff:05.2 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 1 Rank (rev 02) >> ff:05.3 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 1 Thermal Control (rev 02) >> ff:06.0 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 2 Control (rev 02) >> ff:06.1 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 2 Address (rev 02) >> ff:06.2 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 2 Rank (rev 02) >> ff:06.3 Host bridge: Intel Corporation Xeon 5600 Series Integrated >> Memory Controller Channel 2 Thermal Control (rev 02) >> >> >> full dmesg >> >> [??? 0.000000] Linux version 4.19.15-test >> (khlebnikov at kernel1.search.yandex.net) (gcc version 5.4.0 20160609 >> (Ubuntu 5.4.0-6ubuntu1~16.04.11)) #2 SMP Mon Jan 14 12:50:23 UTC 2019 >> [??? 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.19.15-test >> root=/dev/mapper/hdd-root ro pti=off spectre_v2=off consoleblank=0 >> biosdevname=0 net.ifnames=0 >> [??? 0.000000] KERNEL supported cpus: >> [??? 0.000000]?? Intel GenuineIntel >> [??? 0.000000]?? AMD AuthenticAMD >> [??? 0.000000] x86/fpu: x87 FPU will use FXSAVE >> [??? 0.000000] BIOS-provided physical RAM map: >> [??? 0.000000] BIOS-e820: [mem 0x0000000000000100-0x000000000009ebff] >> usable >> [??? 0.000000] BIOS-e820: [mem 0x000000000009ec00-0x000000000009ffff] >> reserved >> [??? 0.000000] BIOS-e820: [mem 0x00000000000e4000-0x00000000000fffff] >> reserved >> [??? 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000bf77ffff] >> usable >> [??? 0.000000] BIOS-e820: [mem 0x00000000bf78e000-0x00000000bf78ffff] >> reserved >> [??? 0.000000] BIOS-e820: [mem 0x00000000bf790000-0x00000000bf79dfff] >> ACPI data >> [??? 0.000000] BIOS-e820: [mem 0x00000000bf79e000-0x00000000bf7cffff] >> ACPI NVS >> [??? 0.000000] BIOS-e820: [mem 0x00000000bf7d0000-0x00000000bf7dffff] >> reserved >> [??? 0.000000] BIOS-e820: [mem 0x00000000bf7ec000-0x00000000bfffffff] >> reserved >> [??? 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] >> reserved >> [??? 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] >> reserved >> [??? 0.000000] BIOS-e820: [mem 0x00000000ffe00000-0x00000000ffffffff] >> reserved >> [??? 0.000000] BIOS-e820: [mem 0x0000000100000000-0x0000000c3fffffff] >> usable >> [??? 0.000000] NX (Execute Disable) protection: active >> [??? 0.000000] SMBIOS 2.5 present. >> [??? 0.000000] DMI: System manufacturer System Product Name/Z8NR-D12, >> BIOS 1501??? 10/25/2011 >> [??? 0.000000] tsc: Fast TSC calibration using PIT >> [??? 0.000000] tsc: Detected 2399.962 MHz processor >> [??? 0.002727] e820: update [mem 0x00000000-0x00000fff] usable ==> >> reserved >> [??? 0.002730] e820: remove [mem 0x000a0000-0x000fffff] usable >> [??? 0.002737] last_pfn = 0xc40000 max_arch_pfn = 0x400000000 >> [??? 0.002742] MTRR default type: uncachable >> [??? 0.002743] MTRR fixed ranges enabled: >> [??? 0.002744]?? 00000-9FFFF write-back >> [??? 0.002745]?? A0000-BFFFF uncachable >> [??? 0.002746]?? C0000-DFFFF write-protect >> [??? 0.002747]?? E0000-E7FFF write-through >> [??? 0.002748]?? E8000-FFFFF write-protect >> [??? 0.002748] MTRR variable ranges enabled: >> [??? 0.002750]?? 0 base 0000000000 mask FF80000000 write-back >> [??? 0.002751]?? 1 base 0080000000 mask FFC0000000 write-back >> [??? 0.002752]?? 2 base 00BF800000 mask FFFF800000 uncachable >> [??? 0.002753]?? 3 base 0100000000 mask FF00000000 write-back >> [??? 0.002754]?? 4 base 0200000000 mask FE00000000 write-back >> [??? 0.002755]?? 5 base 0400000000 mask FC00000000 write-back >> [??? 0.002756]?? 6 base 0800000000 mask FC00000000 write-back >> [??? 0.002757]?? 7 base 0C00000000 mask FFC0000000 write-back >> [??? 0.002757]?? 8 disabled >> [??? 0.002758]?? 9 disabled >> [??? 0.004742] x86/PAT: Configuration [0-7]: WB? WC? UC- UC? WB? WP >> UC- WT >> [??? 0.005299] total RAM covered: 49144M >> [??? 0.005812] Found optimal setting for mtrr clean up >> [??? 0.005814]? gran_size: 64K???? chunk_size: 16M???? num_reg: 8 lose >> cover RAM: 0G >> [??? 0.007189] e820: update [mem 0xbf800000-0xffffffff] usable ==> >> reserved >> [??? 0.007195] last_pfn = 0xbf780 max_arch_pfn = 0x400000000 >> [??? 0.018143] found SMP MP-table at [mem 0x000ff780-0x000ff78f] >> mapped at [(____ptrval____)] >> [??? 0.026523] Scanning 1 areas for low memory corruption >> [??? 0.026527] Base memory trampoline at [(____ptrval____)] 98000 size >> 24576 >> [??? 0.026530] Kernel/User page tables isolation: disabled on command >> line. >> [??? 0.026533] Using GB pages for direct mapping >> [??? 0.026536] BRK [0xc3fc01000, 0xc3fc01fff] PGTABLE >> [??? 0.026539] BRK [0xc3fc02000, 0xc3fc02fff] PGTABLE >> [??? 0.026541] BRK [0xc3fc03000, 0xc3fc03fff] PGTABLE >> [??? 0.026855] BRK [0xc3fc04000, 0xc3fc04fff] PGTABLE >> [??? 0.026912] BRK [0xc3fc05000, 0xc3fc05fff] PGTABLE >> [??? 0.027021] RAMDISK: [mem 0xc3b387000-0xc3dffffff] >> [??? 0.027034] ACPI: Early table checksum verification disabled >> [??? 0.027143] ACPI: RSDP 0x00000000000FB410 000024 (v02 ACPIAM) >> [??? 0.027148] ACPI: XSDT 0x00000000BF790100 000084 (v01 102511 >> XSDT1714 20111025 MSFT 00000097) >> [??? 0.027157] ACPI: FACP 0x00000000BF790290 0000F4 (v03 102511 >> FACP1714 20111025 MSFT 00000097) >> [??? 0.027163] ACPI BIOS Warning (bug): 32/64X length mismatch in >> FADT/Gpe0Block: 128/64 (20180810/tbfadt-569) >> [??? 0.027169] ACPI: DSDT 0x00000000BF790540 005AE1 (v01 S0075 >> S0075001 00000001 INTL 20060113) >> [??? 0.027174] ACPI: FACS 0x00000000BF79E000 000040 >> [??? 0.027177] ACPI: FACS 0x00000000BF79E000 000040 >> [??? 0.027181] ACPI: APIC 0x00000000BF790390 00011E (v01 102511 >> APIC1714 20111025 MSFT 00000097) >> [??? 0.027186] ACPI: MCFG 0x00000000BF7904B0 00003C (v01 102511 >> OEMMCFG 20111025 MSFT 00000097) >> [??? 0.027191] ACPI: SPMI 0x00000000BF7904F0 000041 (v05 102511 >> OEMSPMI 20111025 MSFT 00000097) >> [??? 0.027195] ACPI: OEMB 0x00000000BF79E040 000072 (v01 102511 >> OEMB1714 20111025 MSFT 00000097) >> [??? 0.027200] ACPI: HPET 0x00000000BF798540 000038 (v01 102511 >> OEMHPET 20111025 MSFT 00000097) >> [??? 0.027204] ACPI: SRAT 0x00000000BF798580 000228 (v01 102511 >> OEMSRAT 00000001 INTL 00000001) >> [??? 0.027209] ACPI: SSDT 0x00000000BF79F740 000363 (v01 DpgPmm CpuPm >> 00000012 INTL 20060113) >> [??? 0.027213] ACPI: EINJ 0x00000000BF7987B0 000130 (v01 AMIER >> AMI_EINJ 20111025 MSFT 00000097) >> [??? 0.027218] ACPI: BERT 0x00000000BF798940 000030 (v01 AMIER >> AMI_BERT 20111025 MSFT 00000097) >> [??? 0.027223] ACPI: ERST 0x00000000BF798970 0001B0 (v01 AMIER >> AMI_ERST 20111025 MSFT 00000097) >> [??? 0.027227] ACPI: HEST 0x00000000BF798B20 0000A8 (v01 AMIER >> ABC_HEST 20111025 MSFT 00000097) >> [??? 0.027240] ACPI: Local APIC address 0xfee00000 >> [??? 0.027279] SRAT: PXM 0 -> APIC 0x00 -> Node 0 >> [??? 0.027281] SRAT: PXM 1 -> APIC 0x20 -> Node 1 >> [??? 0.027282] SRAT: PXM 0 -> APIC 0x02 -> Node 0 >> [??? 0.027283] SRAT: PXM 0 -> APIC 0x04 -> Node 0 >> [??? 0.027285] SRAT: PXM 0 -> APIC 0x10 -> Node 0 >> [??? 0.027286] SRAT: PXM 0 -> APIC 0x12 -> Node 0 >> [??? 0.027287] SRAT: PXM 0 -> APIC 0x14 -> Node 0 >> [??? 0.027288] SRAT: PXM 1 -> APIC 0x22 -> Node 1 >> [??? 0.027289] SRAT: PXM 1 -> APIC 0x24 -> Node 1 >> [??? 0.027291] SRAT: PXM 1 -> APIC 0x30 -> Node 1 >> [??? 0.027292] SRAT: PXM 1 -> APIC 0x32 -> Node 1 >> [??? 0.027293] SRAT: PXM 1 -> APIC 0x34 -> Node 1 >> [??? 0.027294] SRAT: PXM 0 -> APIC 0x01 -> Node 0 >> [??? 0.027295] SRAT: PXM 0 -> APIC 0x03 -> Node 0 >> [??? 0.027297] SRAT: PXM 0 -> APIC 0x05 -> Node 0 >> [??? 0.027298] SRAT: PXM 0 -> APIC 0x11 -> Node 0 >> [??? 0.027299] SRAT: PXM 0 -> APIC 0x13 -> Node 0 >> [??? 0.027300] SRAT: PXM 0 -> APIC 0x15 -> Node 0 >> [??? 0.027301] SRAT: PXM 1 -> APIC 0x21 -> Node 1 >> [??? 0.027303] SRAT: PXM 1 -> APIC 0x23 -> Node 1 >> [??? 0.027304] SRAT: PXM 1 -> APIC 0x25 -> Node 1 >> [??? 0.027305] SRAT: PXM 1 -> APIC 0x31 -> Node 1 >> [??? 0.027306] SRAT: PXM 1 -> APIC 0x33 -> Node 1 >> [??? 0.027307] SRAT: PXM 1 -> APIC 0x35 -> Node 1 >> [??? 0.027311] ACPI: SRAT: Node 0 PXM 0 [mem 0x00000000-0xbfffffff] >> [??? 0.027313] ACPI: SRAT: Node 0 PXM 0 [mem 0x100000000-0x63fffffff] >> [??? 0.027314] ACPI: SRAT: Node 1 PXM 1 [mem 0x640000000-0xc3fffffff] >> [??? 0.027317] NUMA: Node 0 [mem 0x00000000-0xbfffffff] + [mem >> 0x100000000-0x63fffffff] -> [mem 0x00000000-0x63fffffff] >> [??? 0.027325] NODE_DATA(0) allocated [mem 0x63fffb000-0x63fffffff] >> [??? 0.027330] NODE_DATA(1) allocated [mem 0xc3fffb000-0xc3fffffff] >> [??? 0.154203] Zone ranges: >> [??? 0.154209]?? DMA????? [mem 0x0000000000001000-0x0000000000ffffff] >> [??? 0.154212]?? DMA32??? [mem 0x0000000001000000-0x00000000ffffffff] >> [??? 0.154214]?? Normal?? [mem 0x0000000100000000-0x0000000c3fffffff] >> [??? 0.154215]?? Device?? empty >> [??? 0.154217] Movable zone start for each node >> [??? 0.154218] Early memory node ranges >> [??? 0.154220]?? node?? 0: [mem 0x0000000000001000-0x000000000009dfff] >> [??? 0.154221]?? node?? 0: [mem 0x0000000000100000-0x00000000bf77ffff] >> [??? 0.154222]?? node?? 0: [mem 0x0000000100000000-0x000000063fffffff] >> [??? 0.154223]?? node?? 1: [mem 0x0000000640000000-0x0000000c3fffffff] >> [??? 0.154230] Reserved but unavailable: 99 pages >> [??? 0.154232] Initmem setup node 0 [mem >> 0x0000000000001000-0x000000063fffffff] >> [??? 0.154235] On node 0 totalpages: 6289181 >> [??? 0.154236]?? DMA zone: 64 pages used for memmap >> [??? 0.154237]?? DMA zone: 21 pages reserved >> [??? 0.154238]?? DMA zone: 3997 pages, LIFO batch:0 >> [??? 0.154919]?? DMA32 zone: 12190 pages used for memmap >> [??? 0.154920]?? DMA32 zone: 780160 pages, LIFO batch:63 >> [??? 0.180889]?? Normal zone: 86016 pages used for memmap >> [??? 0.180892]?? Normal zone: 5505024 pages, LIFO batch:63 >> [??? 0.348852] Initmem setup node 1 [mem >> 0x0000000640000000-0x0000000c3fffffff] >> [??? 0.348858] On node 1 totalpages: 6291456 >> [??? 0.348859]?? Normal zone: 98304 pages used for memmap >> [??? 0.348860]?? Normal zone: 6291456 pages, LIFO batch:63 >> [??? 0.546041] ACPI: PM-Timer IO Port: 0x808 >> [??? 0.546048] ACPI: Local APIC address 0xfee00000 >> [??? 0.546059] ACPI: LAPIC_NMI (acpi_id[0xff] high level lint[0x1]) >> [??? 0.546071] IOAPIC[0]: apic_id 6, version 32, address 0xfec00000, >> GSI 0-23 >> [??? 0.546077] IOAPIC[1]: apic_id 7, version 32, address 0xfec8a000, >> GSI 24-47 >> [??? 0.546080] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) >> [??? 0.546083] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high >> level) >> [??? 0.546085] ACPI: IRQ0 used by override. >> [??? 0.546087] ACPI: IRQ9 used by override. >> [??? 0.546091] Using ACPI (MADT) for SMP configuration information >> [??? 0.546093] ACPI: HPET id: 0x8086a301 base: 0xfed00000 >> [??? 0.546104] smpboot: Allowing 24 CPUs, 0 hotplug CPUs >> [??? 0.546128] [mem 0xc0000000-0xdfffffff] available for PCI devices >> [??? 0.546130] Booting paravirtualized kernel on bare hardware >> [??? 0.546134] clocksource: refined-jiffies: mask: 0xffffffff >> max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns >> [??? 0.819690] random: get_random_bytes called from >> start_kernel+0x94/0x551 with crng_init=0 >> [??? 0.819704] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 >> nr_cpu_ids:24 nr_node_ids:2 >> [??? 0.821567] percpu: Embedded 44 pages/cpu @(____ptrval____) s142104 >> r8192 d29928 u262144 >> [??? 0.821588] pcpu-alloc: s142104 r8192 d29928 u262144 alloc=1*2097152 >> [??? 0.821589] pcpu-alloc: [0] 00 01 02 03 04 05 12 13 [0] 14 15 16 17 >> -- -- -- -- >> [??? 0.821597] pcpu-alloc: [1] 06 07 08 09 10 11 18 19 [1] 20 21 22 23 >> -- -- -- -- >> [??? 0.821649] Built 2 zonelists, mobility grouping on.? Total pages: >> 12384042 >> [??? 0.821651] Policy zone: Normal >> [??? 0.821654] Kernel command line: >> BOOT_IMAGE=/boot/vmlinuz-4.19.15-test root=/dev/mapper/hdd-root ro >> pti=off spectre_v2=off consoleblank=0 biosdevname=0 net.ifnames=0 >> [??? 1.061324] Memory: 49390984K/50322548K available (12300K kernel >> code, 1435K rwdata, 3552K rodata, 3120K init, 2152K bss, 931564K >> reserved, 0K cma-reserved) >> [??? 1.061738] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=24, >> Nodes=2 >> [??? 1.061749] ftrace: allocating 35866 entries in 141 pages >> [??? 1.083258] rcu: Hierarchical RCU implementation. >> [??? 1.083260] rcu:???? RCU restricting CPUs from NR_CPUS=256 to >> nr_cpu_ids=24. >> [??? 1.083262]???? Tasks RCU enabled. >> [??? 1.083263] rcu: Adjusting geometry for rcu_fanout_leaf=16, >> nr_cpu_ids=24 >> [??? 1.088283] NR_IRQS: 16640, nr_irqs: 1024, preallocated irqs: 16 >> [??? 1.088954] Console: colour dummy device 80x25 >> [??? 1.089200] console [tty0] enabled >> [??? 1.092754] ACPI: Core revision 20180810 >> [??? 1.092825] ACPI BIOS Warning (bug): Incorrect checksum in table >> [OEMB] - 0xFF, should be 0xFC (20180810/tbprint-177) >> [??? 1.093228] clocksource: hpet: mask: 0xffffffff max_cycles: >> 0xffffffff, max_idle_ns: 133484882848 ns >> [??? 1.093240] hpet clockevent registered >> [??? 1.093261] APIC: Switch to symmetric I/O mode setup >> [??? 1.093266] Switched APIC routing to physical flat. >> [??? 1.094011] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 >> [??? 1.113247] clocksource: tsc-early: mask: 0xffffffffffffffff >> max_cycles: 0x229813d283d, max_idle_ns: 440795313186 ns >> [??? 1.113264] Calibrating delay loop (skipped), value calculated >> using timer frequency.. 4799.92 BogoMIPS (lpj=9599848) >> [??? 1.113269] pid_max: default: 24576 minimum: 301 >> [??? 1.113820] Security Framework initialized >> [??? 1.113826] AppArmor: AppArmor disabled by boot time parameter >> [??? 1.129364] Dentry cache hash table entries: 8388608 (order: 14, >> 67108864 bytes) >> [??? 1.137165] Inode-cache hash table entries: 4194304 (order: 13, >> 33554432 bytes) >> [??? 1.137641] Mount-cache hash table entries: 131072 (order: 8, >> 1048576 bytes) >> [??? 1.137890] Mountpoint-cache hash table entries: 131072 (order: 8, >> 1048576 bytes) >> [??? 1.139425] mce: CPU supports 9 MCE banks >> [??? 1.139443] CPU0: Thermal monitoring enabled (TM1) >> [??? 1.139452] process: using mwait in idle threads >> [??? 1.139457] Last level iTLB entries: 4KB 512, 2MB 7, 4MB 7 >> [??? 1.139460] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32, 1GB 0 >> [??? 1.139464] Spectre V2 : off selected on command line. >> [??? 1.139467] Speculative Store Bypass: Vulnerable >> [??? 1.146528] Freeing SMP alternatives memory: 36K >> [??? 1.149252] smpboot: CPU0: Intel(R) Xeon(R) CPU?????????? E5645? @ >> 2.40GHz (family: 0x6, model: 0x2c, stepping: 0x2) >> [??? 1.149252] Performance Events: PEBS fmt1+, Westmere events, >> 16-deep LBR, Intel PMU driver. >> [??? 1.149252] core: CPUID marked event: 'bus cycles' unavailable >> [??? 1.149252] ... version:??????????????? 3 >> [??? 1.149252] ... bit width:????????????? 48 >> [??? 1.149252] ... generic registers:????? 4 >> [??? 1.149252] ... value mask:???????????? 0000ffffffffffff >> [??? 1.149252] ... max period:???????????? 000000007fffffff >> [??? 1.149252] ... fixed-purpose events:?? 3 >> [??? 1.149252] ... event mask:???????????? 000000070000000f >> [??? 1.149252] rcu: Hierarchical SRCU implementation. >> [??? 1.149252] NMI watchdog: Enabled. Permanently consumes one hw-PMU >> counter. >> [??? 1.149252] smp: Bringing up secondary CPUs ... >> [??? 1.149473] x86: Booting SMP configuration: >> [??? 1.149478] .... node? #0, CPUs:??????? #1? #2? #3? #4? #5 >> [??? 1.167622] .... node? #1, CPUs:??? #6? #7? #8? #9 #10 #11 >> [??? 1.267291] .... node? #0, CPUs:?? #12 #13 #14 #15 #16 #17 >> [??? 1.289370] .... node? #1, CPUs:?? #18 #19 #20 #21 #22 #23 >> [??? 1.311358] smp: Brought up 2 nodes, 24 CPUs >> [??? 1.311358] smpboot: Max logical packages: 2 >> [??? 1.311358] smpboot: Total of 24 processors activated (115201.89 >> BogoMIPS) >> [??? 1.321566] devtmpfs: initialized >> [??? 1.321841] x86/mm: Memory block size: 128MB >> [??? 1.341323] PM: Registering ACPI NVS region [mem >> 0xbf79e000-0xbf7cffff] (204800 bytes) >> [??? 1.341586] clocksource: jiffies: mask: 0xffffffff max_cycles: >> 0xffffffff, max_idle_ns: 7645041785100000 ns >> [??? 1.341586] futex hash table entries: 8192 (order: 7, 524288 bytes) >> [??? 1.342141] >> [??? 1.342144] >> ************************************************************* >> [??? 1.342147] **???? NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE >> NOTICE??? ** >> [??? 1.342150] >> **???????????????????????????????????????????????????????? ** >> [??? 1.342152] **? IOMMU DebugFS SUPPORT HAS BEEN ENABLED IN THIS >> KERNEL? ** >> [??? 1.342155] >> **???????????????????????????????????????????????????????? ** >> [??? 1.342157] ** This means that this kernel is built to expose >> internal ** >> [??? 1.342160] ** IOMMU data structures, which may compromise security >> on ** >> [??? 1.342163] ** your >> system.??????????????????????????????????????????? ** >> [??? 1.342165] >> **???????????????????????????????????????????????????????? ** >> [??? 1.342168] ** If you see this message and you are not debugging >> the?? ** >> [??? 1.342170] ** kernel, report this immediately to your >> vendor!???????? ** >> [??? 1.342173] >> **???????????????????????????????????????????????????????? ** >> [??? 1.342175] **???? NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE >> NOTICE??? ** >> [??? 1.342178] >> ************************************************************* >> [??? 1.342178] NET: Registered protocol family 16 >> [??? 1.342178] audit: initializing netlink subsys (disabled) >> [??? 1.345305] audit: type=2000 audit(1547472106.256:1): >> state=initialized audit_enabled=0 res=1 >> [??? 1.345648] cpuidle: using governor ladder >> [??? 1.345648] cpuidle: using governor menu >> [??? 1.345648] ACPI: bus type PCI registered >> [??? 1.345648] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 >> [??? 1.346105] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem >> 0xe0000000-0xefffffff] (base 0xe0000000) >> [??? 1.346113] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved >> in E820 >> [??? 1.346143] PCI: Using configuration type 1 for base access >> [??? 1.357552] HugeTLB registered 1.00 GiB page size, pre-allocated 0 >> pages >> [??? 1.357552] HugeTLB registered 2.00 MiB page size, pre-allocated 0 >> pages >> [??? 1.357552] cryptd: max_cpu_qlen set to 1000 >> [??? 1.357694] ACPI: Added _OSI(Module Device) >> [??? 1.357698] ACPI: Added _OSI(Processor Device) >> [??? 1.357701] ACPI: Added _OSI(3.0 _SCP Extensions) >> [??? 1.357703] ACPI: Added _OSI(Processor Aggregator Device) >> [??? 1.357711] ACPI: Added _OSI(Linux-Dell-Video) >> [??? 1.357717] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio) >> [??? 1.396417] ACPI: 2 ACPI AML tables successfully acquired and loaded >> [??? 1.402387] ACPI: Dynamic OEM Table Load: >> [??? 1.402400] ACPI: SSDT 0xFFFF888623B79000 000C69 (v01 PmRef >> P001Cst 00003001 INTL 20060113) >> [??? 1.407461] ACPI: Dynamic OEM Table Load: >> [??? 1.407471] ACPI: SSDT 0xFFFF888623B7A000 000A0A (v01 PmRef >> Cpu0Tst 00003000 INTL 20060113) >> [??? 1.414439] ACPI: Interpreter enabled >> [??? 1.414479] ACPI: (supports S0 S1 S5) >> [??? 1.414483] ACPI: Using IOAPIC for interrupt routing >> [??? 1.414745] HEST: Table parsing has been initialized. >> [??? 1.414751] PCI: Using host bridge windows from ACPI; if necessary, >> use "pci=nocrs" and report a bug >> [??? 1.416164] ACPI: Enabled 11 GPEs in block 00 to 3F >> [??? 1.473587] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) >> [??? 1.473605] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM >> ClockPM Segments MSI] >> [??? 1.473637] acpi PNP0A08:00: _OSC failed (AE_NOT_FOUND); disabling >> ASPM >> [??? 1.475546] PCI host bridge to bus 0000:00 >> [??? 1.475555] pci_bus 0000:00: root bus resource [io? 0x0000-0x0cf7 >> window] >> [??? 1.475561] pci_bus 0000:00: root bus resource [io? 0x0d00-0xffff >> window] >> [??? 1.475567] pci_bus 0000:00: root bus resource [mem >> 0x000a0000-0x000bffff window] >> [??? 1.475573] pci_bus 0000:00: root bus resource [mem >> 0x000d0000-0x000dffff window] >> [??? 1.475579] pci_bus 0000:00: root bus resource [mem >> 0xc0000000-0xdfffffff window] >> [??? 1.475585] pci_bus 0000:00: root bus resource [mem >> 0xf0000000-0xfed8ffff window] >> [??? 1.475592] pci_bus 0000:00: root bus resource [bus 00-ff] >> [??? 1.475613] pci 0000:00:00.0: [8086:3403] type 00 class 0x060000 >> [??? 1.475695] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold >> [??? 1.476135] pci 0000:00:01.0: [8086:3408] type 01 class 0x060400 >> [??? 1.476208] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold >> [??? 1.476692] pci 0000:00:02.0: [8086:3409] type 01 class 0x060400 >> [??? 1.476761] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold >> [??? 1.477242] pci 0000:00:03.0: [8086:340a] type 01 class 0x060400 >> [??? 1.477320] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold >> [??? 1.477806] pci 0000:00:07.0: [8086:340e] type 01 class 0x060400 >> [??? 1.477878] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold >> [??? 1.478354] pci 0000:00:08.0: [8086:340f] type 01 class 0x060400 >> [??? 1.478422] pci 0000:00:08.0: PME# supported from D0 D3hot D3cold >> [??? 1.478893] pci 0000:00:09.0: [8086:3410] type 01 class 0x060400 >> [??? 1.478962] pci 0000:00:09.0: PME# supported from D0 D3hot D3cold >> [??? 1.479438] pci 0000:00:0a.0: [8086:3411] type 01 class 0x060400 >> [??? 1.479507] pci 0000:00:0a.0: PME# supported from D0 D3hot D3cold >> [??? 1.479984] pci 0000:00:10.0: [8086:3425] type 00 class 0x080000 >> [??? 1.480408] pci 0000:00:10.1: [8086:3426] type 00 class 0x080000 >> [??? 1.480823] pci 0000:00:11.0: [8086:3427] type 00 class 0x080000 >> [??? 1.481241] pci 0000:00:11.1: [8086:3428] type 00 class 0x080000 >> [??? 1.481659] pci 0000:00:14.0: [8086:342e] type 00 class 0x080000 >> [??? 1.482099] pci 0000:00:14.1: [8086:3422] type 00 class 0x080000 >> [??? 1.482535] pci 0000:00:14.2: [8086:3423] type 00 class 0x080000 >> [??? 1.482971] pci 0000:00:14.3: [8086:3438] type 00 class 0x080000 >> [??? 1.483389] pci 0000:00:16.0: [8086:3430] type 00 class 0x088000 >> [??? 1.483405] pci 0000:00:16.0: reg 0x10: [mem 0xfbcd8000-0xfbcdbfff >> 64bit] >> [??? 1.483846] pci 0000:00:16.1: [8086:3431] type 00 class 0x088000 >> [??? 1.483862] pci 0000:00:16.1: reg 0x10: [mem 0xfbcdc000-0xfbcdffff >> 64bit] >> [??? 1.484304] pci 0000:00:16.2: [8086:3432] type 00 class 0x088000 >> [??? 1.484319] pci 0000:00:16.2: reg 0x10: [mem 0xfbce0000-0xfbce3fff >> 64bit] >> [??? 1.484758] pci 0000:00:16.3: [8086:3433] type 00 class 0x088000 >> [??? 1.484774] pci 0000:00:16.3: reg 0x10: [mem 0xfbce4000-0xfbce7fff >> 64bit] >> [??? 1.485216] pci 0000:00:16.4: [8086:3429] type 00 class 0x088000 >> [??? 1.485232] pci 0000:00:16.4: reg 0x10: [mem 0xfbce8000-0xfbcebfff >> 64bit] >> [??? 1.485684] pci 0000:00:16.5: [8086:342a] type 00 class 0x088000 >> [??? 1.485700] pci 0000:00:16.5: reg 0x10: [mem 0xfbcec000-0xfbceffff >> 64bit] >> [??? 1.486148] pci 0000:00:16.6: [8086:342b] type 00 class 0x088000 >> [??? 1.486164] pci 0000:00:16.6: reg 0x10: [mem 0xfbcf0000-0xfbcf3fff >> 64bit] >> [??? 1.486610] pci 0000:00:16.7: [8086:342c] type 00 class 0x088000 >> [??? 1.486625] pci 0000:00:16.7: reg 0x10: [mem 0xfbcf4000-0xfbcf7fff >> 64bit] >> [??? 1.487076] pci 0000:00:1a.0: [8086:3a37] type 00 class 0x0c0300 >> [??? 1.487118] pci 0000:00:1a.0: reg 0x20: [io? 0xa400-0xa41f] >> [??? 1.487604] pci 0000:00:1a.1: [8086:3a38] type 00 class 0x0c0300 >> [??? 1.487647] pci 0000:00:1a.1: reg 0x20: [io? 0xa480-0xa49f] >> [??? 1.488132] pci 0000:00:1a.7: [8086:3a3c] type 00 class 0x0c0320 >> [??? 1.488153] pci 0000:00:1a.7: reg 0x10: [mem 0xfbcf8000-0xfbcf83ff] >> [??? 1.488244] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold >> [??? 1.488690] pci 0000:00:1c.0: [8086:3a40] type 01 class 0x060400 >> [??? 1.488781] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold >> [??? 1.489256] pci 0000:00:1c.4: [8086:3a48] type 01 class 0x060400 >> [??? 1.489349] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold >> [??? 1.489816] pci 0000:00:1c.5: [8086:3a4a] type 01 class 0x060400 >> [??? 1.489907] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold >> [??? 1.490363] pci 0000:00:1d.0: [8086:3a34] type 00 class 0x0c0300 >> [??? 1.490405] pci 0000:00:1d.0: reg 0x20: [io? 0xa800-0xa81f] >> [??? 1.490880] pci 0000:00:1d.1: [8086:3a35] type 00 class 0x0c0300 >> [??? 1.490922] pci 0000:00:1d.1: reg 0x20: [io? 0xa880-0xa89f] >> [??? 1.491407] pci 0000:00:1d.2: [8086:3a36] type 00 class 0x0c0300 >> [??? 1.491450] pci 0000:00:1d.2: reg 0x20: [io? 0xac00-0xac1f] >> [??? 1.491925] pci 0000:00:1d.3: [8086:3a39] type 00 class 0x0c0300 >> [??? 1.491967] pci 0000:00:1d.3: reg 0x20: [io? 0xb000-0xb01f] >> [??? 1.492454] pci 0000:00:1d.7: [8086:3a3a] type 00 class 0x0c0320 >> [??? 1.492475] pci 0000:00:1d.7: reg 0x10: [mem 0xfbcf9000-0xfbcf93ff] >> [??? 1.492565] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold >> [??? 1.493002] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401 >> [??? 1.493503] pci 0000:00:1f.0: [8086:3a16] type 00 class 0x060100 >> [??? 1.493595] pci 0000:00:1f.0: quirk: [io? 0x0800-0x087f] claimed by >> ICH6 ACPI/GPIO/TCO >> [??? 1.493604] pci 0000:00:1f.0: quirk: [io? 0x0500-0x053f] claimed by >> ICH6 GPIO >> [??? 1.493610] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at >> 0ca0 (mask 0003) >> [??? 1.493617] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 4 PIO at >> 0294 (mask 0003) >> [??? 1.494066] pci 0000:00:1f.2: [8086:3a22] type 00 class 0x010601 >> [??? 1.494084] pci 0000:00:1f.2: reg 0x10: [io? 0xb080-0xb087] >> [??? 1.494090] pci 0000:00:1f.2: reg 0x14: [io? 0xb880-0xb883] >> [??? 1.494097] pci 0000:00:1f.2: reg 0x18: [io? 0xb800-0xb807] >> [??? 1.494104] pci 0000:00:1f.2: reg 0x1c: [io? 0xb480-0xb483] >> [??? 1.494111] pci 0000:00:1f.2: reg 0x20: [io? 0xb400-0xb41f] >> [??? 1.494118] pci 0000:00:1f.2: reg 0x24: [mem 0xfbcfa000-0xfbcfa7ff] >> [??? 1.494168] pci 0000:00:1f.2: PME# supported from D3hot >> [??? 1.494605] pci 0000:00:1f.3: [8086:3a30] type 00 class 0x0c0500 >> [??? 1.494623] pci 0000:00:1f.3: reg 0x10: [mem 0xfbcfb000-0xfbcfb0ff >> 64bit] >> [??? 1.494642] pci 0000:00:1f.3: reg 0x20: [io? 0x0400-0x041f] >> [??? 1.495109] pci 0000:00:01.0: PCI bridge to [bus 0b] >> [??? 1.495201] pci 0000:00:02.0: PCI bridge to [bus 0a] >> [??? 1.495296] pci 0000:00:03.0: PCI bridge to [bus 09] >> [??? 1.495388] pci 0000:00:07.0: PCI bridge to [bus 08] >> [??? 1.495476] pci 0000:00:08.0: PCI bridge to [bus 07] >> [??? 1.495565] pci 0000:00:09.0: PCI bridge to [bus 06] >> [??? 1.495657] pci 0000:00:0a.0: PCI bridge to [bus 05] >> [??? 1.495748] pci 0000:00:1c.0: PCI bridge to [bus 04] >> [??? 1.495754] pci 0000:00:1c.0:?? bridge window [io? 0x1000-0x1fff] >> [??? 1.495757] pci 0000:00:1c.0:?? bridge window [mem >> 0xc0000000-0xc01fffff] >> [??? 1.495761] pci 0000:00:1c.0:?? bridge window [mem >> 0xc0200000-0xc03fffff 64bit pref] >> [??? 1.495873] pci 0000:03:00.0: [8086:10d3] type 00 class 0x020000 >> [??? 1.495914] pci 0000:03:00.0: reg 0x10: [mem 0xfbee0000-0xfbefffff] >> [??? 1.495945] pci 0000:03:00.0: reg 0x18: [io? 0xec00-0xec1f] >> [??? 1.495961] pci 0000:03:00.0: reg 0x1c: [mem 0xfbedc000-0xfbedffff] >> [??? 1.496132] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold >> [??? 1.496364] pci 0000:00:1c.4: PCI bridge to [bus 03] >> [??? 1.496370] pci 0000:00:1c.4:?? bridge window [io? 0xe000-0xefff] >> [??? 1.496373] pci 0000:00:1c.4:?? bridge window [mem >> 0xfbe00000-0xfbefffff] >> [??? 1.496378] pci 0000:00:1c.4:?? bridge window [mem >> 0xc0400000-0xc05fffff 64bit pref] >> [??? 1.496492] pci 0000:02:00.0: [8086:10d3] type 00 class 0x020000 >> [??? 1.496533] pci 0000:02:00.0: reg 0x10: [mem 0xfbde0000-0xfbdfffff] >> [??? 1.496564] pci 0000:02:00.0: reg 0x18: [io? 0xdc00-0xdc1f] >> [??? 1.496580] pci 0000:02:00.0: reg 0x1c: [mem 0xfbddc000-0xfbddffff] >> [??? 1.496749] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold >> [??? 1.496979] pci 0000:00:1c.5: PCI bridge to [bus 02] >> [??? 1.496985] pci 0000:00:1c.5:?? bridge window [io? 0xd000-0xdfff] >> [??? 1.496988] pci 0000:00:1c.5:?? bridge window [mem >> 0xfbd00000-0xfbdfffff] >> [??? 1.496993] pci 0000:00:1c.5:?? bridge window [mem >> 0xc0600000-0xc07fffff 64bit pref] >> [??? 1.497015] pci_bus 0000:01: extended config space not accessible >> [??? 1.497089] pci 0000:01:01.0: [1a03:2000] type 00 class 0x030000 >> [??? 1.497105] pci 0000:01:01.0: reg 0x10: [mem 0xfb000000-0xfb7fffff] >> [??? 1.497114] pci 0000:01:01.0: reg 0x14: [mem 0xfafe0000-0xfaffffff] >> [??? 1.497123] pci 0000:01:01.0: reg 0x18: [io? 0xcc00-0xcc7f] >> [??? 1.497202] pci 0000:01:01.0: supports D1 D2 >> [??? 1.497203] pci 0000:01:01.0: PME# supported from D0 D1 D2 D3hot >> D3cold >> [??? 1.497371] pci 0000:00:1e.0: PCI bridge to [bus 01] (subtractive >> decode) >> [??? 1.497377] pci 0000:00:1e.0:?? bridge window [io? 0xc000-0xcfff] >> [??? 1.497380] pci 0000:00:1e.0:?? bridge window [mem >> 0xfaf00000-0xfb7fffff] >> [??? 1.497388] pci 0000:00:1e.0:?? bridge window [io? 0x0000-0x0cf7 >> window] (subtractive decode) >> [??? 1.497393] pci 0000:00:1e.0:?? bridge window [io? 0x0d00-0xffff >> window] (subtractive decode) >> [??? 1.497396] pci 0000:00:1e.0:?? bridge window [mem >> 0x000a0000-0x000bffff window] (subtractive decode) >> [??? 1.497399] pci 0000:00:1e.0:?? bridge window [mem >> 0x000d0000-0x000dffff window] (subtractive decode) >> [??? 1.497402] pci 0000:00:1e.0:?? bridge window [mem >> 0xc0000000-0xdfffffff window] (subtractive decode) >> [??? 1.497406] pci 0000:00:1e.0:?? bridge window [mem >> 0xf0000000-0xfed8ffff window] (subtractive decode) >> [??? 1.501795] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12 >> 14 15), disabled. >> [??? 1.502156] ACPI: PCI Interrupt Link [LNKB] (IRQs *5), disabled. >> [??? 1.502514] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 *11 12 >> 14 15), disabled. >> [??? 1.502876] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12 >> *14 15), disabled. >> [??? 1.503235] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12 >> 14 15) *0, disabled. >> [??? 1.503603] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 *7 10 11 12 >> 14 15), disabled. >> [??? 1.503961] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 6 7 10 11 12 >> 14 15) *0, disabled. >> [??? 1.504321] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 6 7 10 11 12 >> 14 *15), disabled. >> [??? 1.505424] SCSI subsystem initialized >> [??? 1.505509] libata version 3.00 loaded. >> [??? 1.505509] ACPI: bus type USB registered >> [??? 1.505509] usbcore: registered new interface driver usbfs >> [??? 1.505509] usbcore: registered new interface driver hub >> [??? 1.509258] usbcore: registered new device driver usb >> [??? 1.509258] pps_core: LinuxPPS API ver. 1 registered >> [??? 1.509258] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 >> Rodolfo Giometti >> [??? 1.509258] PTP clock support registered >> [??? 1.509335] EDAC MC: Ver: 3.0.0 >> [??? 1.509528] PCI: Using ACPI for IRQ routing >> [??? 1.512566] PCI: Discovered peer bus fe >> [??? 1.512574] PCI: root bus fe: using default resources >> [??? 1.512578] PCI: Probing PCI hardware (bus fe) >> [??? 1.512672] PCI host bridge to bus 0000:fe >> [??? 1.512678] pci_bus 0000:fe: root bus resource [io? 0x0000-0xffff] >> [??? 1.512684] pci_bus 0000:fe: root bus resource [mem >> 0x00000000-0xffffffffff] >> [??? 1.512688] pci_bus 0000:fe: No busn resource found for root bus, >> will use [bus fe-ff] >> [??? 1.512693] pci_bus 0000:fe: busn_res: can not insert [bus fe-ff] >> under domain [bus 00-ff] (conflicts with (null) [bus 00-ff]) >> [??? 1.512702] pci 0000:fe:00.0: [8086:2c70] type 00 class 0x060000 >> [??? 1.512838] pci 0000:fe:00.1: [8086:2d81] type 00 class 0x060000 >> [??? 1.512967] pci 0000:fe:02.0: [8086:2d90] type 00 class 0x060000 >> [??? 1.513096] pci 0000:fe:02.1: [8086:2d91] type 00 class 0x060000 >> [??? 1.513223] pci 0000:fe:02.2: [8086:2d92] type 00 class 0x060000 >> [??? 1.513357] pci 0000:fe:02.3: [8086:2d93] type 00 class 0x060000 >> [??? 1.513480] pci 0000:fe:02.4: [8086:2d94] type 00 class 0x060000 >> [??? 1.513603] pci 0000:fe:02.5: [8086:2d95] type 00 class 0x060000 >> [??? 1.513725] pci 0000:fe:03.0: [8086:2d98] type 00 class 0x060000 >> [??? 1.513847] pci 0000:fe:03.1: [8086:2d99] type 00 class 0x060000 >> [??? 1.513967] pci 0000:fe:03.2: [8086:2d9a] type 00 class 0x060000 >> [??? 1.514091] pci 0000:fe:03.4: [8086:2d9c] type 00 class 0x060000 >> [??? 1.514213] pci 0000:fe:04.0: [8086:2da0] type 00 class 0x060000 >> [??? 1.514336] pci 0000:fe:04.1: [8086:2da1] type 00 class 0x060000 >> [??? 1.514456] pci 0000:fe:04.2: [8086:2da2] type 00 class 0x060000 >> [??? 1.514579] pci 0000:fe:04.3: [8086:2da3] type 00 class 0x060000 >> [??? 1.514701] pci 0000:fe:05.0: [8086:2da8] type 00 class 0x060000 >> [??? 1.514824] pci 0000:fe:05.1: [8086:2da9] type 00 class 0x060000 >> [??? 1.514944] pci 0000:fe:05.2: [8086:2daa] type 00 class 0x060000 >> [??? 1.515067] pci 0000:fe:05.3: [8086:2dab] type 00 class 0x060000 >> [??? 1.515190] pci 0000:fe:06.0: [8086:2db0] type 00 class 0x060000 >> [??? 1.515316] pci 0000:fe:06.1: [8086:2db1] type 00 class 0x060000 >> [??? 1.515438] pci 0000:fe:06.2: [8086:2db2] type 00 class 0x060000 >> [??? 1.515561] pci 0000:fe:06.3: [8086:2db3] type 00 class 0x060000 >> [??? 1.515693] pci_bus 0000:fe: busn_res: [bus fe-ff] end is updated >> to fe >> [??? 1.515695] pci_bus 0000:fe: busn_res: can not insert [bus fe] >> under domain [bus 00-ff] (conflicts with (null) [bus 00-ff]) >> [??? 1.515704] PCI: Discovered peer bus ff >> [??? 1.515709] PCI: root bus ff: using default resources >> [??? 1.515713] PCI: Probing PCI hardware (bus ff) >> [??? 1.515800] PCI host bridge to bus 0000:ff >> [??? 1.515806] pci_bus 0000:ff: root bus resource [io? 0x0000-0xffff] >> [??? 1.515812] pci_bus 0000:ff: root bus resource [mem >> 0x00000000-0xffffffffff] >> [??? 1.515816] pci_bus 0000:ff: No busn resource found for root bus, >> will use [bus ff-ff] >> [??? 1.515820] pci_bus 0000:ff: busn_res: can not insert [bus ff] >> under domain [bus 00-ff] (conflicts with (null) [bus 00-ff]) >> [??? 1.515829] pci 0000:ff:00.0: [8086:2c70] type 00 class 0x060000 >> [??? 1.515951] pci 0000:ff:00.1: [8086:2d81] type 00 class 0x060000 >> [??? 1.516071] pci 0000:ff:02.0: [8086:2d90] type 00 class 0x060000 >> [??? 1.516191] pci 0000:ff:02.1: [8086:2d91] type 00 class 0x060000 >> [??? 1.516308] pci 0000:ff:02.2: [8086:2d92] type 00 class 0x060000 >> [??? 1.516427] pci 0000:ff:02.3: [8086:2d93] type 00 class 0x060000 >> [??? 1.516544] pci 0000:ff:02.4: [8086:2d94] type 00 class 0x060000 >> [??? 1.516663] pci 0000:ff:02.5: [8086:2d95] type 00 class 0x060000 >> [??? 1.516780] pci 0000:ff:03.0: [8086:2d98] type 00 class 0x060000 >> [??? 1.516900] pci 0000:ff:03.1: [8086:2d99] type 00 class 0x060000 >> [??? 1.517023] pci 0000:ff:03.2: [8086:2d9a] type 00 class 0x060000 >> [??? 1.517151] pci 0000:ff:03.4: [8086:2d9c] type 00 class 0x060000 >> [??? 1.517280] pci 0000:ff:04.0: [8086:2da0] type 00 class 0x060000 >> [??? 1.517415] pci 0000:ff:04.1: [8086:2da1] type 00 class 0x060000 >> [??? 1.517543] pci 0000:ff:04.2: [8086:2da2] type 00 class 0x060000 >> [??? 1.517674] pci 0000:ff:04.3: [8086:2da3] type 00 class 0x060000 >> [??? 1.517794] pci 0000:ff:05.0: [8086:2da8] type 00 class 0x060000 >> [??? 1.517914] pci 0000:ff:05.1: [8086:2da9] type 00 class 0x060000 >> [??? 1.518032] pci 0000:ff:05.2: [8086:2daa] type 00 class 0x060000 >> [??? 1.518156] pci 0000:ff:05.3: [8086:2dab] type 00 class 0x060000 >> [??? 1.518277] pci 0000:ff:06.0: [8086:2db0] type 00 class 0x060000 >> [??? 1.518403] pci 0000:ff:06.1: [8086:2db1] type 00 class 0x060000 >> [??? 1.518525] pci 0000:ff:06.2: [8086:2db2] type 00 class 0x060000 >> [??? 1.518649] pci 0000:ff:06.3: [8086:2db3] type 00 class 0x060000 >> [??? 1.518778] pci_bus 0000:ff: busn_res: [bus ff] end is updated to ff >> [??? 1.518781] pci_bus 0000:ff: busn_res: can not insert [bus ff] >> under domain [bus 00-ff] (conflicts with (null) [bus 00-ff]) >> [??? 1.518789] PCI: pci_cache_line_size set to 64 bytes >> [??? 1.518908] e820: reserve RAM buffer [mem 0x0009ec00-0x0009ffff] >> [??? 1.518913] e820: reserve RAM buffer [mem 0xbf780000-0xbfffffff] >> [??? 1.519482] NetLabel: Initializing >> [??? 1.519486] NetLabel:? domain hash size = 128 >> [??? 1.519488] NetLabel:? protocols = UNLABELED CIPSOv4 CALIPSO >> [??? 1.519548] NetLabel:? unlabeled traffic allowed by default >> [??? 1.521922] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0 >> [??? 1.521929] hpet0: 4 comparators, 64-bit 14.318180 MHz counter >> [??? 1.525254] clocksource: Switched to clocksource tsc-early >> [??? 1.588793] VFS: Disk quotas dquot_6.6.0 >> [??? 1.589142] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 >> bytes) >> [??? 1.589729] pnp: PnP ACPI init >> [??? 1.590002] system 00:00: [mem 0xfbf00000-0xfbffffff] has been >> reserved >> [??? 1.590012] system 00:00: [mem 0xfc000000-0xfcffffff] has been >> reserved >> [??? 1.590020] system 00:00: [mem 0xfd000000-0xfdffffff] has been >> reserved >> [??? 1.590029] system 00:00: [mem 0xfe000000-0xfebfffff] has been >> reserved >> [??? 1.590039] system 00:00: [mem 0xfec8a000-0xfec8afff] could not be >> reserved >> [??? 1.590047] system 00:00: [mem 0xfed10000-0xfed10fff] has been >> reserved >> [??? 1.590060] system 00:00: Plug and Play ACPI device, IDs PNP0c01 >> (active) >> [??? 1.590356] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active) >> [??? 1.591596] pnp 00:02: [dma 0 disabled] >> [??? 1.591807] pnp 00:02: Plug and Play ACPI device, IDs PNP0501 (active) >> [??? 1.592919] system 00:03: [io? 0x0290-0x029f] has been reserved >> [??? 1.592933] system 00:03: Plug and Play ACPI device, IDs PNP0c02 >> (active) >> [??? 1.593940] system 00:04: [io? 0x04d0-0x04d1] has been reserved >> [??? 1.593951] system 00:04: [io? 0x0ca0-0x0caf] could not be reserved >> [??? 1.593960] system 00:04: [io? 0x0800-0x087f] has been reserved >> [??? 1.593968] system 00:04: [io? 0x0500-0x057f] could not be reserved >> [??? 1.593977] system 00:04: [mem 0xfed1c000-0xfed1ffff] has been >> reserved >> [??? 1.593985] system 00:04: [mem 0xfed20000-0xfed3ffff] has been >> reserved >> [??? 1.593993] system 00:04: [mem 0xfed40000-0xfed8ffff] has been >> reserved >> [??? 1.594006] system 00:04: Plug and Play ACPI device, IDs PNP0c02 >> (active) >> [??? 1.594622] system 00:05: [mem 0xffc00000-0xffdfffff] has been >> reserved >> [??? 1.594637] system 00:05: Plug and Play ACPI device, IDs PNP0c02 >> (active) >> [??? 1.595868] pnp 00:06: [dma 0 disabled] >> [??? 1.596121] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active) >> [??? 1.596912] system 00:07: [mem 0xfec00000-0xfec00fff] could not be >> reserved >> [??? 1.596922] system 00:07: [mem 0xfee00000-0xfee00fff] has been >> reserved >> [??? 1.596935] system 00:07: Plug and Play ACPI device, IDs PNP0c02 >> (active) >> [??? 1.597688] system 00:08: [mem 0xe0000000-0xefffffff] has been >> reserved >> [??? 1.597702] system 00:08: Plug and Play ACPI device, IDs PNP0c02 >> (active) >> [??? 1.598760] system 00:09: [mem 0x00000000-0x0009ffff] could not be >> reserved >> [??? 1.598771] system 00:09: [mem 0x000c0000-0x000cffff] could not be >> reserved >> [??? 1.598779] system 00:09: [mem 0x000e0000-0x000fffff] could not be >> reserved >> [??? 1.598788] system 00:09: [mem 0x00100000-0xbfffffff] could not be >> reserved >> [??? 1.598796] system 00:09: [mem 0xfed90000-0xffffffff] could not be >> reserved >> [??? 1.598808] system 00:09: Plug and Play ACPI device, IDs PNP0c01 >> (active) >> [??? 1.599591] pnp: PnP ACPI: found 10 devices >> [??? 1.609238] clocksource: acpi_pm: mask: 0xffffff max_cycles: >> 0xffffff, max_idle_ns: 2085701024 ns >> [??? 1.609547] pci 0000:00:01.0: PCI bridge to [bus 0b] >> [??? 1.609559] pci 0000:00:02.0: PCI bridge to [bus 0a] >> [??? 1.609568] pci 0000:00:03.0: PCI bridge to [bus 09] >> [??? 1.609577] pci 0000:00:07.0: PCI bridge to [bus 08] >> [??? 1.609586] pci 0000:00:08.0: PCI bridge to [bus 07] >> [??? 1.609595] pci 0000:00:09.0: PCI bridge to [bus 06] >> [??? 1.609604] pci 0000:00:0a.0: PCI bridge to [bus 05] >> [??? 1.609614] pci 0000:00:1c.0: PCI bridge to [bus 04] >> [??? 1.609618] pci 0000:00:1c.0:?? bridge window [io? 0x1000-0x1fff] >> [??? 1.609624] pci 0000:00:1c.0:?? bridge window [mem >> 0xc0000000-0xc01fffff] >> [??? 1.609630] pci 0000:00:1c.0:?? bridge window [mem >> 0xc0200000-0xc03fffff 64bit pref] >> [??? 1.609637] pci 0000:00:1c.4: PCI bridge to [bus 03] >> [??? 1.609641] pci 0000:00:1c.4:?? bridge window [io? 0xe000-0xefff] >> [??? 1.609647] pci 0000:00:1c.4:?? bridge window [mem >> 0xfbe00000-0xfbefffff] >> [??? 1.609652] pci 0000:00:1c.4:?? bridge window [mem >> 0xc0400000-0xc05fffff 64bit pref] >> [??? 1.609659] pci 0000:00:1c.5: PCI bridge to [bus 02] >> [??? 1.609663] pci 0000:00:1c.5:?? bridge window [io? 0xd000-0xdfff] >> [??? 1.609669] pci 0000:00:1c.5:?? bridge window [mem >> 0xfbd00000-0xfbdfffff] >> [??? 1.609674] pci 0000:00:1c.5:?? bridge window [mem >> 0xc0600000-0xc07fffff 64bit pref] >> [??? 1.609682] pci 0000:00:1e.0: PCI bridge to [bus 01] >> [??? 1.609685] pci 0000:00:1e.0:?? bridge window [io? 0xc000-0xcfff] >> [??? 1.609691] pci 0000:00:1e.0:?? bridge window [mem >> 0xfaf00000-0xfb7fffff] >> [??? 1.609700] pci_bus 0000:00: resource 4 [io? 0x0000-0x0cf7 window] >> [??? 1.609702] pci_bus 0000:00: resource 5 [io? 0x0d00-0xffff window] >> [??? 1.609704] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff >> window] >> [??? 1.609705] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff >> window] >> [??? 1.609706] pci_bus 0000:00: resource 8 [mem 0xc0000000-0xdfffffff >> window] >> [??? 1.609708] pci_bus 0000:00: resource 9 [mem 0xf0000000-0xfed8ffff >> window] >> [??? 1.609710] pci_bus 0000:04: resource 0 [io? 0x1000-0x1fff] >> [??? 1.609711] pci_bus 0000:04: resource 1 [mem 0xc0000000-0xc01fffff] >> [??? 1.609712] pci_bus 0000:04: resource 2 [mem 0xc0200000-0xc03fffff >> 64bit pref] >> [??? 1.609714] pci_bus 0000:03: resource 0 [io? 0xe000-0xefff] >> [??? 1.609715] pci_bus 0000:03: resource 1 [mem 0xfbe00000-0xfbefffff] >> [??? 1.609716] pci_bus 0000:03: resource 2 [mem 0xc0400000-0xc05fffff >> 64bit pref] >> [??? 1.609718] pci_bus 0000:02: resource 0 [io? 0xd000-0xdfff] >> [??? 1.609719] pci_bus 0000:02: resource 1 [mem 0xfbd00000-0xfbdfffff] >> [??? 1.609720] pci_bus 0000:02: resource 2 [mem 0xc0600000-0xc07fffff >> 64bit pref] >> [??? 1.609721] pci_bus 0000:01: resource 0 [io? 0xc000-0xcfff] >> [??? 1.609723] pci_bus 0000:01: resource 1 [mem 0xfaf00000-0xfb7fffff] >> [??? 1.609724] pci_bus 0000:01: resource 4 [io? 0x0000-0x0cf7 window] >> [??? 1.609725] pci_bus 0000:01: resource 5 [io? 0x0d00-0xffff window] >> [??? 1.609727] pci_bus 0000:01: resource 6 [mem 0x000a0000-0x000bffff >> window] >> [??? 1.609728] pci_bus 0000:01: resource 7 [mem 0x000d0000-0x000dffff >> window] >> [??? 1.609729] pci_bus 0000:01: resource 8 [mem 0xc0000000-0xdfffffff >> window] >> [??? 1.609730] pci_bus 0000:01: resource 9 [mem 0xf0000000-0xfed8ffff >> window] >> [??? 1.609919] pci_bus 0000:fe: resource 4 [io? 0x0000-0xffff] >> [??? 1.609921] pci_bus 0000:fe: resource 5 [mem 0x00000000-0xffffffffff] >> [??? 1.609925] pci_bus 0000:ff: resource 4 [io? 0x0000-0xffff] >> [??? 1.609926] pci_bus 0000:ff: resource 5 [mem 0x00000000-0xffffffffff] >> [??? 1.610214] NET: Registered protocol family 2 >> [??? 1.611173] tcp_listen_portaddr_hash hash table entries: 32768 >> (order: 7, 524288 bytes) >> [??? 1.611471] TCP established hash table entries: 524288 (order: 10, >> 4194304 bytes) >> [??? 1.612462] TCP bind hash table entries: 65536 (order: 8, 1048576 >> bytes) >> [??? 1.612648] TCP: Hash tables configured (established 524288 bind >> 65536) >> [??? 1.613006] UDP hash table entries: 32768 (order: 8, 1048576 bytes) >> [??? 1.613265] UDP-Lite hash table entries: 32768 (order: 8, 1048576 >> bytes) >> [??? 1.614214] NET: Registered protocol family 1 >> [??? 1.614235] NET: Registered protocol family 44 >> [??? 1.626925] PCI: CLS mismatch (256 != 64), using 64 bytes >> [??? 1.626936] pci 0000:01:01.0: Video device with shadowed ROM at >> [mem 0x000c0000-0x000dffff] >> [??? 1.627146] Unpacking initramfs... >> [??? 2.477623] Freeing initrd memory: 45540K >> [??? 2.477657] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) >> [??? 2.477661] software IO TLB: mapped [mem 0xbb780000-0xbf780000] (64MB) >> [??? 2.479356] Scanning for low memory corruption every 60 seconds >> [??? 2.482475] Initialise system trusted keyrings >> [??? 2.482588] workingset: timestamp_bits=40 max_order=24 bucket_order=0 >> [??? 2.493004] pstore: using deflate compression >> [??? 2.495503] Key type asymmetric registered >> [??? 2.495507] Asymmetric key parser 'x509' registered >> [??? 2.495539] Block layer SCSI generic (bsg) driver version 0.4 >> loaded (major 247) >> [??? 2.495668] io scheduler noop registered >> [??? 2.495672] io scheduler deadline registered >> [??? 2.495847] io scheduler cfq registered (default) >> [??? 2.495850] io scheduler mq-deadline registered >> [??? 2.495853] io scheduler kyber registered >> [??? 2.496009] io scheduler bfq registered >> [??? 2.499857] shpchp: Standard Hot Plug PCI Controller Driver >> version: 0.4 >> [??? 2.499895] intel_idle: MWAIT substates: 0x1120 >> [??? 2.499896] intel_idle: v0.4.1 model 0x2C >> [??? 2.504152] intel_idle: lapic_timer_reliable_states 0xffffffff >> [??? 2.504388] input: Power Button as >> /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 >> [??? 2.504431] ACPI: Power Button [PWRB] >> [??? 2.504572] input: Power Button as >> /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 >> [??? 2.504606] ACPI: Power Button [PWRF] >> [??? 2.516388] ERST: Failed to get Error Log Address Range. >> [??? 2.516492] [Firmware Warn]: GHES: Poll interval is 0 for generic >> hardware error source: 1, disabled. >> [??? 2.516884] GHES: APEI firmware first mode is enabled by WHEA _OSC. >> [??? 2.517153] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled >> [??? 2.537668] 00:02: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) >> is a 16550A >> [??? 2.558508] 00:06: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) >> is a 16550A >> [??? 2.564580] Linux agpgart interface v0.103 >> [??? 2.600179] loop: module loaded >> [??? 2.601655] ahci 0000:00:1f.2: version 3.0 >> [??? 2.602777] ahci 0000:00:1f.2: SSS flag set, parallel bus scan >> disabled >> [??? 2.602821] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 >> Gbps 0x3f impl SATA mode >> [??? 2.602827] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led >> clo pmp pio slum part ccc ems sxs >> [??? 2.663791] scsi host0: ahci >> [??? 2.664940] scsi host1: ahci >> [??? 2.665911] scsi host2: ahci >> [??? 2.666866] scsi host3: ahci >> [??? 2.667668] scsi host4: ahci >> [??? 2.668623] scsi host5: ahci >> [??? 2.669051] ata1: SATA max UDMA/133 abar m2048 at 0xfbcfa000 port >> 0xfbcfa100 irq 24 >> [??? 2.669056] ata2: SATA max UDMA/133 abar m2048 at 0xfbcfa000 port >> 0xfbcfa180 irq 24 >> [??? 2.669061] ata3: SATA max UDMA/133 abar m2048 at 0xfbcfa000 port >> 0xfbcfa200 irq 24 >> [??? 2.669065] ata4: SATA max UDMA/133 abar m2048 at 0xfbcfa000 port >> 0xfbcfa280 irq 24 >> [??? 2.669069] ata5: SATA max UDMA/133 abar m2048 at 0xfbcfa000 port >> 0xfbcfa300 irq 24 >> [??? 2.669073] ata6: SATA max UDMA/133 abar m2048 at 0xfbcfa000 port >> 0xfbcfa380 irq 24 >> [??? 2.669276] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver >> [??? 2.669289] ehci-pci: EHCI PCI platform driver >> [??? 2.670123] ehci-pci 0000:00:1a.7: EHCI Host Controller >> [??? 2.670152] ehci-pci 0000:00:1a.7: new USB bus registered, assigned >> bus number 1 >> [??? 2.670174] ehci-pci 0000:00:1a.7: debug port 1 >> [??? 2.674091] ehci-pci 0000:00:1a.7: cache line size of 64 is not >> supported >> [??? 2.674127] ehci-pci 0000:00:1a.7: irq 18, io mem 0xfbcf8000 >> [??? 2.689391] ehci-pci 0000:00:1a.7: USB 2.0 started, EHCI 1.00 >> [??? 2.689556] usb usb1: New USB device found, idVendor=1d6b, >> idProduct=0002, bcdDevice= 4.19 >> [??? 2.689562] usb usb1: New USB device strings: Mfr=3, Product=2, >> SerialNumber=1 >> [??? 2.689566] usb usb1: Product: EHCI Host Controller >> [??? 2.689569] usb usb1: Manufacturer: Linux 4.19.15-test ehci_hcd >> [??? 2.689572] usb usb1: SerialNumber: 0000:00:1a.7 >> [??? 2.690048] hub 1-0:1.0: USB hub found >> [??? 2.690075] hub 1-0:1.0: 4 ports detected >> [??? 2.691370] ehci-pci 0000:00:1d.7: EHCI Host Controller >> [??? 2.691390] ehci-pci 0000:00:1d.7: new USB bus registered, assigned >> bus number 2 >> [??? 2.691408] ehci-pci 0000:00:1d.7: debug port 1 >> [??? 2.695331] ehci-pci 0000:00:1d.7: cache line size of 64 is not >> supported >> [??? 2.695365] ehci-pci 0000:00:1d.7: irq 23, io mem 0xfbcf9000 >> [??? 2.709370] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00 >> [??? 2.709571] usb usb2: New USB device found, idVendor=1d6b, >> idProduct=0002, bcdDevice= 4.19 >> [??? 2.709577] usb usb2: New USB device strings: Mfr=3, Product=2, >> SerialNumber=1 >> [??? 2.709581] usb usb2: Product: EHCI Host Controller >> [??? 2.709584] usb usb2: Manufacturer: Linux 4.19.15-test ehci_hcd >> [??? 2.709587] usb usb2: SerialNumber: 0000:00:1d.7 >> [??? 2.710112] hub 2-0:1.0: USB hub found >> [??? 2.710138] hub 2-0:1.0: 8 ports detected >> [??? 2.710777] ehci-platform: EHCI generic platform driver >> [??? 2.710799] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver >> [??? 2.710810] ohci-pci: OHCI PCI platform driver >> [??? 2.710845] ohci-platform: OHCI generic platform driver >> [??? 2.710866] uhci_hcd: USB Universal Host Controller Interface driver >> [??? 2.711635] uhci_hcd 0000:00:1a.0: UHCI Host Controller >> [??? 2.711658] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned >> bus number 3 >> [??? 2.711672] uhci_hcd 0000:00:1a.0: detected 2 ports >> [??? 2.711721] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000a400 >> [??? 2.711875] usb usb3: New USB device found, idVendor=1d6b, >> idProduct=0001, bcdDevice= 4.19 >> [??? 2.711880] usb usb3: New USB device strings: Mfr=3, Product=2, >> SerialNumber=1 >> [??? 2.711884] usb usb3: Product: UHCI Host Controller >> [??? 2.711887] usb usb3: Manufacturer: Linux 4.19.15-test uhci_hcd >> [??? 2.711890] usb usb3: SerialNumber: 0000:00:1a.0 >> [??? 2.712369] hub 3-0:1.0: USB hub found >> [??? 2.712394] hub 3-0:1.0: 2 ports detected >> [??? 2.713563] uhci_hcd 0000:00:1a.1: UHCI Host Controller >> [??? 2.713582] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned >> bus number 4 >> [??? 2.713595] uhci_hcd 0000:00:1a.1: detected 2 ports >> [??? 2.713641] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000a480 >> [??? 2.713786] usb usb4: New USB device found, idVendor=1d6b, >> idProduct=0001, bcdDevice= 4.19 >> [??? 2.713791] usb usb4: New USB device strings: Mfr=3, Product=2, >> SerialNumber=1 >> [??? 2.713795] usb usb4: Product: UHCI Host Controller >> [??? 2.713798] usb usb4: Manufacturer: Linux 4.19.15-test uhci_hcd >> [??? 2.713801] usb usb4: SerialNumber: 0000:00:1a.1 >> [??? 2.714349] hub 4-0:1.0: USB hub found >> [??? 2.714374] hub 4-0:1.0: 2 ports detected >> [??? 2.715419] uhci_hcd 0000:00:1d.0: UHCI Host Controller >> [??? 2.715440] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned >> bus number 5 >> [??? 2.715453] uhci_hcd 0000:00:1d.0: detected 2 ports >> [??? 2.715479] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000a800 >> [??? 2.715628] usb usb5: New USB device found, idVendor=1d6b, >> idProduct=0001, bcdDevice= 4.19 >> [??? 2.715633] usb usb5: New USB device strings: Mfr=3, Product=2, >> SerialNumber=1 >> [??? 2.715637] usb usb5: Product: UHCI Host Controller >> [??? 2.715640] usb usb5: Manufacturer: Linux 4.19.15-test uhci_hcd >> [??? 2.715644] usb usb5: SerialNumber: 0000:00:1d.0 >> [??? 2.716147] hub 5-0:1.0: USB hub found >> [??? 2.716172] hub 5-0:1.0: 2 ports detected >> [??? 2.717309] uhci_hcd 0000:00:1d.1: UHCI Host Controller >> [??? 2.717329] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned >> bus number 6 >> [??? 2.717342] uhci_hcd 0000:00:1d.1: detected 2 ports >> [??? 2.717392] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000a880 >> [??? 2.717538] usb usb6: New USB device found, idVendor=1d6b, >> idProduct=0001, bcdDevice= 4.19 >> [??? 2.717543] usb usb6: New USB device strings: Mfr=3, Product=2, >> SerialNumber=1 >> [??? 2.717547] usb usb6: Product: UHCI Host Controller >> [??? 2.717550] usb usb6: Manufacturer: Linux 4.19.15-test uhci_hcd >> [??? 2.717553] usb usb6: SerialNumber: 0000:00:1d.1 >> [??? 2.718067] hub 6-0:1.0: USB hub found >> [??? 2.718092] hub 6-0:1.0: 2 ports detected >> [??? 2.719136] uhci_hcd 0000:00:1d.2: UHCI Host Controller >> [??? 2.719159] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned >> bus number 7 >> [??? 2.719173] uhci_hcd 0000:00:1d.2: detected 2 ports >> [??? 2.719198] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ac00 >> [??? 2.719349] usb usb7: New USB device found, idVendor=1d6b, >> idProduct=0001, bcdDevice= 4.19 >> [??? 2.719355] usb usb7: New USB device strings: Mfr=3, Product=2, >> SerialNumber=1 >> [??? 2.719358] usb usb7: Product: UHCI Host Controller >> [??? 2.719362] usb usb7: Manufacturer: Linux 4.19.15-test uhci_hcd >> [??? 2.719365] usb usb7: SerialNumber: 0000:00:1d.2 >> [??? 2.719874] hub 7-0:1.0: USB hub found >> [??? 2.719900] hub 7-0:1.0: 2 ports detected >> [??? 2.720948] uhci_hcd 0000:00:1d.3: UHCI Host Controller >> [??? 2.720970] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned >> bus number 8 >> [??? 2.720983] uhci_hcd 0000:00:1d.3: detected 2 ports >> [??? 2.721007] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000b000 >> [??? 2.721158] usb usb8: New USB device found, idVendor=1d6b, >> idProduct=0001, bcdDevice= 4.19 >> [??? 2.721164] usb usb8: New USB device strings: Mfr=3, Product=2, >> SerialNumber=1 >> [??? 2.721167] usb usb8: Product: UHCI Host Controller >> [??? 2.721171] usb usb8: Manufacturer: Linux 4.19.15-test uhci_hcd >> [??? 2.721174] usb usb8: SerialNumber: 0000:00:1d.3 >> [??? 2.721695] hub 8-0:1.0: USB hub found >> [??? 2.721720] hub 8-0:1.0: 2 ports detected >> [??? 2.722152] i8042: PNP: No PS/2 controller found. >> [??? 2.722156] i8042: Probing ports directly. >> [??? 2.724937] serio: i8042 KBD port at 0x60,0x64 irq 1 >> [??? 2.725036] serio: i8042 AUX port at 0x60,0x64 irq 12 >> [??? 2.725464] mousedev: PS/2 mouse device common for all mice >> [??? 2.726192] rtc_cmos 00:01: RTC can wake from S4 >> [??? 2.726607] rtc_cmos 00:01: registered as rtc0 >> [??? 2.726706] rtc_cmos 00:01: alarms up to one month, y3k, 114 bytes >> nvram, hpet irqs >> [??? 2.727227] softdog: initialized. soft_noboot=0 soft_margin=60 sec >> soft_panic=0 (nowayout=0) >> [??? 2.727457] device-mapper: uevent: version 1.0.3 >> [??? 2.727837] device-mapper: ioctl: 4.39.0-ioctl (2018-04-03) >> initialised: dm-devel at redhat.com >> [??? 2.727927] hidraw: raw HID events driver (C) Jiri Kosina >> [??? 2.728007] usbcore: registered new interface driver usbhid >> [??? 2.728010] usbhid: USB HID core driver >> [??? 2.729238] NET: Registered protocol family 10 >> [??? 2.730665] Segment Routing with IPv6 >> [??? 2.730704] NET: Registered protocol family 17 >> [??? 2.730928] 9pnet: Installing 9P2000 support >> [??? 2.730990] Key type dns_resolver registered >> [??? 2.737631] microcode: sig=0x206c2, pf=0x1, revision=0x14 >> [??? 2.739351] microcode: Microcode Update Driver: v2.2. >> [??? 2.739382] SSE version of gcm_enc/dec engaged. >> [??? 2.741624] sched_clock: Marking stable (2741022334, >> 595663)->(2894195291, -152577294) >> [??? 2.753699] registered taskstats version 1 >> [??? 2.753732] Loading compiled-in X.509 certificates >> [??? 2.757130] Loaded X.509 cert 'Build time autogenerated kernel key: >> 21712f2d003fcbb2b79eca54bcc739cd6c76842b' >> [??? 2.757183] kmemleak: Kernel memory leak detector initialized >> [??? 2.757185] kmemleak: Automatic memory scanning thread started >> [??? 2.761103] Key type big_key registered >> [??? 2.763134] Key type trusted registered >> [??? 2.765145] Key type encrypted registered >> [??? 2.767263] APEI: Can not request [mem 0xbf7988e0-0xbf798933] for >> APEI BERT registers >> [??? 2.768539] rtc_cmos 00:01: setting system clock to 2019-01-14 >> 13:21:47 UTC (1547472107) >> [??? 3.025361] usb 1-3: new high-speed USB device number 2 using ehci-pci >> [??? 3.145363] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) >> [??? 3.146438] ata1.00: ATA-8: WDC WD5003ABYX-01WERA0, 01.01S01, max >> UDMA/133 >> [??? 3.146447] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth >> 32), AA >> [??? 3.147681] ata1.00: configured for UDMA/133 >> [??? 3.149784] scsi 0:0:0:0: Direct-Access???? ATA????? WDC >> WD5003ABYX-0 1S01 PQ: 0 ANSI: 5 >> [??? 3.150309] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: >> (500 GB/466 GiB) >> [??? 3.150326] sd 0:0:0:0: [sda] Write Protect is off >> [??? 3.150330] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 >> [??? 3.150345] sd 0:0:0:0: [sda] Write cache: enabled, read cache: >> enabled, doesn't support DPO or FUA >> [??? 3.150557] sd 0:0:0:0: Attached scsi generic sg0 type 0 >> [??? 3.190121]? sda: sda1 sda2 >> [??? 3.192040] sd 0:0:0:0: [sda] Attached SCSI disk >> [??? 3.199307] usb 1-3: New USB device found, idVendor=046b, >> idProduct=ff01, bcdDevice= 1.00 >> [??? 3.199317] usb 1-3: New USB device strings: Mfr=1, Product=2, >> SerialNumber=3 >> [??? 3.199323] usb 1-3: Product: Generic Hub >> [??? 3.199328] usb 1-3: Manufacturer: American Megatrends Inc. >> [??? 3.199332] usb 1-3: SerialNumber: serial >> [??? 3.200474] hub 1-3:1.0: USB hub found >> [??? 3.200799] hub 1-3:1.0: 3 ports detected >> [??? 3.489342] usb 1-3.1: new low-speed USB device number 3 using >> ehci-pci >> [??? 3.489379] tsc: Refined TSC clocksource calibration: 2400.085 MHz >> [??? 3.490496] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: >> 0x229887d25b0, max_idle_ns: 440795264680 ns >> [??? 3.490630] clocksource: Switched to clocksource tsc >> [??? 3.611970] usb 1-3.1: New USB device found, idVendor=046b, >> idProduct=ff10, bcdDevice= 1.00 >> [??? 3.611980] usb 1-3.1: New USB device strings: Mfr=1, Product=2, >> SerialNumber=3 >> [??? 3.611987] usb 1-3.1: Product: Virtual Keyboard and Mouse >> [??? 3.611992] usb 1-3.1: Manufacturer: American Megatrends Inc. >> [??? 3.611997] usb 1-3.1: SerialNumber: serial >> [??? 3.615035] input: American Megatrends Inc. Virtual Keyboard and >> Mouse as >> /devices/pci0000:00/0000:00:1a.7/usb1/1-3/1-3.1/1-3.1:1.0/0003:046B:FF10.0001/input/input5 >> >> [??? 3.615360] hid-generic 0003:046B:FF10.0001: input,hidraw0: USB HID >> v1.10 Keyboard [American Megatrends Inc. Virtual Keyboard and Mouse] >> on usb-0000:00:1a.7-3.1/input0 >> [??? 3.617227] input: American Megatrends Inc. Virtual Keyboard and >> Mouse as >> /devices/pci0000:00/0000:00:1a.7/usb1/1-3/1-3.1/1-3.1:1.1/0003:046B:FF10.0002/input/input6 >> >> [??? 3.617927] hid-generic 0003:046B:FF10.0002: input,hidraw1: USB HID >> v1.10 Mouse [American Megatrends Inc. Virtual Keyboard and Mouse] on >> usb-0000:00:1a.7-3.1/input1 >> [??? 3.625364] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) >> [??? 3.626587] ata2.00: ATA-8: WDC WD5003ABYX-01WERA0, 01.01S01, max >> UDMA/133 >> [??? 3.626596] ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth >> 32), AA >> [??? 3.627925] ata2.00: configured for UDMA/133 >> [??? 3.630038] scsi 1:0:0:0: Direct-Access???? ATA????? WDC >> WD5003ABYX-0 1S01 PQ: 0 ANSI: 5 >> [??? 3.630564] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: >> (500 GB/466 GiB) >> [??? 3.630578] sd 1:0:0:0: [sdb] Write Protect is off >> [??? 3.630582] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 >> [??? 3.630597] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: >> enabled, doesn't support DPO or FUA >> [??? 3.630828] sd 1:0:0:0: Attached scsi generic sg1 type 0 >> [??? 3.673781]? sdb: sdb1 sdb2 sdb3 >> [??? 3.676054] sd 1:0:0:0: [sdb] Attached SCSI disk >> [??? 4.105338] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) >> [??? 4.106597] ata3.00: ATA-8: WDC WD5003ABYX-01WERA0, 01.01S01, max >> UDMA/133 >> [??? 4.106605] ata3.00: 976773168 sectors, multi 0: LBA48 NCQ (depth >> 32), AA >> [??? 4.108018] ata3.00: configured for UDMA/133 >> [??? 4.110074] scsi 2:0:0:0: Direct-Access???? ATA????? WDC >> WD5003ABYX-0 1S01 PQ: 0 ANSI: 5 >> [??? 4.110602] sd 2:0:0:0: [sdc] 976773168 512-byte logical blocks: >> (500 GB/466 GiB) >> [??? 4.110617] sd 2:0:0:0: [sdc] Write Protect is off >> [??? 4.110621] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00 >> [??? 4.110635] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: >> enabled, doesn't support DPO or FUA >> [??? 4.110814] sd 2:0:0:0: Attached scsi generic sg2 type 0 >> [??? 4.158584]? sdc: sdc1 sdc2 sdc3 >> [??? 4.160880] sd 2:0:0:0: [sdc] Attached SCSI disk >> [??? 4.585336] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) >> [??? 4.586590] ata4.00: ATA-8: WDC WD5003ABYX-01WERA0, 01.01S01, max >> UDMA/133 >> [??? 4.586599] ata4.00: 976773168 sectors, multi 0: LBA48 NCQ (depth >> 32), AA >> [??? 4.588022] ata4.00: configured for UDMA/133 >> [??? 4.590075] scsi 3:0:0:0: Direct-Access???? ATA????? WDC >> WD5003ABYX-0 1S01 PQ: 0 ANSI: 5 >> [??? 4.590594] sd 3:0:0:0: [sdd] 976773168 512-byte logical blocks: >> (500 GB/466 GiB) >> [??? 4.590608] sd 3:0:0:0: [sdd] Write Protect is off >> [??? 4.590612] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00 >> [??? 4.590626] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: >> enabled, doesn't support DPO or FUA >> [??? 4.590849] sd 3:0:0:0: Attached scsi generic sg3 type 0 >> [??? 4.632974]? sdd: sdd1 sdd2 sdd3 >> [??? 4.635127] sd 3:0:0:0: [sdd] Attached SCSI disk >> [??? 4.905051] ata5: SATA link down (SStatus 0 SControl 300) >> [??? 5.221052] ata6: SATA link down (SStatus 0 SControl 300) >> [??? 5.229148] Freeing unused kernel image memory: 3120K >> [??? 5.241546] Write protecting the kernel read-only data: 18432k >> [??? 5.247968] Freeing unused kernel image memory: 2008K >> [??? 5.249315] Freeing unused kernel image memory: 544K >> [??? 5.249329] Run /init as init process >> [??? 5.269776] random: systemd-udevd: uninitialized urandom read (16 >> bytes read) >> [??? 5.269931] random: systemd-udevd: uninitialized urandom read (16 >> bytes read) >> [??? 5.269951] random: systemd-udevd: uninitialized urandom read (16 >> bytes read) >> [??? 5.445362] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k >> [??? 5.445369] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. >> [??? 5.446215] e1000e 0000:03:00.0: Interrupt Throttling Rate >> (ints/sec) set to dynamic conservative mode >> [??? 5.509680] [drm] Using P2A bridge for configuration >> [??? 5.509690] [drm] AST 1100 detected >> [??? 5.509698] [drm] Analog VGA only >> [??? 5.509714] [drm] dram MCLK=204 Mhz type=0 bus_width=16 size=00800000 >> [??? 5.510025] [TTM] Zone? kernel: Available graphics memory: 24721116 >> kiB >> [??? 5.510030] [TTM] Zone?? dma32: Available graphics memory: 2097152 kiB >> [??? 5.510033] [TTM] Initializing pool allocator >> [??? 5.510076] [TTM] Initializing DMA pool allocator >> [??? 5.511391] e1000e 0000:03:00.0 0000:03:00.0 (uninitialized): >> registered PHC clock >> [??? 5.515154] fbcon: astdrmfb (fb0) is primary device >> [??? 5.572320] e1000e 0000:03:00.0 eth0: (PCI Express:2.5GT/s:Width >> x1) bc:ae:c5:28:22:fd >> [??? 5.572322] e1000e 0000:03:00.0 eth0: Intel(R) PRO/1000 Network >> Connection >> [??? 5.572458] e1000e 0000:03:00.0 eth0: MAC: 3, PHY: 8, PBA No: >> FFFFFF-0FF >> [??? 5.572915] e1000e 0000:02:00.0: Interrupt Throttling Rate >> (ints/sec) set to dynamic conservative mode >> [??? 5.573176] Console: switching to colour frame buffer device 128x48 >> [??? 5.592883] random: fast init done >> [??? 5.613610] md0: detected capacity change from 0 to 64390955008 >> [??? 5.623024] md/raid1:md1: active with 2 out of 2 mirrors >> [??? 5.623106] md1: detected capacity change from 0 to 38364250112 >> [??? 5.631682] ast 0000:01:01.0: fb0: astdrmfb frame buffer device >> [??? 5.633022] e1000e 0000:02:00.0 0000:02:00.0 (uninitialized): >> registered PHC clock >> [??? 5.645407] [drm] Initialized ast 0.1.0 20120228 for 0000:01:01.0 >> on minor 0 >> [??? 5.692749] e1000e 0000:02:00.0 eth1: (PCI Express:2.5GT/s:Width >> x1) bc:ae:c5:28:23:f8 >> [??? 5.692786] e1000e 0000:02:00.0 eth1: Intel(R) PRO/1000 Network >> Connection >> [??? 5.692895] e1000e 0000:02:00.0 eth1: MAC: 3, PHY: 8, PBA No: >> FFFFFF-0FF >> [??? 5.989325] raid6: sse2x1?? gen()? 5861 MB/s >> [??? 6.057315] raid6: sse2x1?? xor()? 4574 MB/s >> [??? 6.125329] raid6: sse2x2?? gen()? 6910 MB/s >> [??? 6.193320] raid6: sse2x2?? xor()? 5372 MB/s >> [??? 6.261333] raid6: sse2x4?? gen()? 7498 MB/s >> [??? 6.329324] raid6: sse2x4?? xor()? 6005 MB/s >> [??? 6.329341] raid6: using algorithm sse2x4 gen() 7498 MB/s >> [??? 6.329361] raid6: .... xor() 6005 MB/s, rmw enabled >> [??? 6.330094] raid6: using ssse3x2 recovery algorithm >> [??? 6.344940] xor: measuring software checksum speed >> [??? 6.385316]??? prefetch64-sse: 10077.000 MB/sec >> [??? 6.425316]??? generic_sse:? 8850.000 MB/sec >> [??? 6.425997] xor: using function: prefetch64-sse (10077.000 MB/sec) >> [??? 6.438419] async_tx: api initialized (async) >> [??? 6.756899] random: crng init done >> [??? 6.757738] random: 7 urandom warning(s) missed due to ratelimiting >> [??? 7.083576] EXT4-fs (dm-0): mounted filesystem with ordered data >> mode. Opts: (null) >> [?? 10.355614] EXT4-fs (dm-0): re-mounted. Opts: barrier=1 >> [?? 11.246338] NMI watchdog: Enabled. Permanently consumes one hw-PMU >> counter. >> [?? 12.244091] ACPI Warning: SystemIO range >> 0x0000000000000828-0x000000000000082F conflicts with OpRegion >> 0x0000000000000800-0x000000000000084F (\PMRG) (20180810/utaddress-213) >> [?? 12.244131] ACPI Warning: SystemIO range >> 0x0000000000000828-0x000000000000082F conflicts with OpRegion >> 0x0000000000000828-0x000000000000082B (\_SB.PCI0.SBRG.GPE0) >> (20180810/utaddress-213) >> [?? 12.244151] ACPI: If an ACPI driver is available for this device, >> you should use it instead of the native driver >> [?? 12.244890] lpc_ich: Resource conflict(s) found affecting gpio_ich >> [?? 12.626199] EDAC MC1: Giving out device to module i7core_edac.c >> controller i7 core #1: DEV 0000:fe:03.0 (INTERRUPT) >> [?? 12.626326] EDAC PCI0: Giving out device to module i7core_edac >> controller EDAC PCI controller: DEV 0000:fe:03.0 (POLLED) >> [?? 12.628046] EDAC MC0: Giving out device to module i7core_edac.c >> controller i7 core #0: DEV 0000:ff:03.0 (INTERRUPT) >> [?? 12.628317] EDAC PCI1: Giving out device to module i7core_edac >> controller EDAC PCI controller: DEV 0000:ff:03.0 (POLLED) >> [?? 12.628368] EDAC i7core: Driver loaded, 2 memory controller(s) found. >> [?? 12.667768] dca service started, version 1.12.1 >> [?? 12.681581] ipmi message handler version 39.2 >> [?? 12.722702] ipmi device interface >> [?? 12.729599] gpiochip_find_base: found new base at 451 >> [?? 12.730067] gpio gpiochip0: (gpio_ich): added GPIO chardev (254:0) >> [?? 12.730272] gpiochip_setup_dev: registered GPIOs 451 to 511 on >> device: gpiochip0 (gpio_ich) >> [?? 12.730273] gpio_ich: GPIO from 451 to 511 on gpio_ich >> [?? 12.758585] IPMI System Interface driver. >> [?? 12.758623] ipmi_si dmi-ipmi-si.0: ipmi_platform: probing via SMBIOS >> [?? 12.758625] ipmi_si: SMBIOS: io 0xca2 regsize 1 spacing 1 irq 0 >> [?? 12.758629] ipmi_si: Adding SMBIOS-specified kcs state machine >> [?? 12.758701] ipmi_si IPI0001:00: ipmi_platform: probing via ACPI >> [?? 12.758802] ipmi_si IPI0001:00: [io? 0x0ca2-0x0ca3] regsize 1 >> spacing 1 irq 0 >> [?? 12.758807] ipmi_si dmi-ipmi-si.0: Removing SMBIOS-specified kcs >> state machine in favor of ACPI >> [?? 12.758808] ipmi_si: Adding ACPI-specified kcs state machine >> [?? 12.758976] ipmi_si: Trying ACPI-specified kcs state machine at i/o >> address 0xca2, slave address 0x20, irq 0 >> [?? 12.790833] ioatdma: Intel(R) QuickData Technology Driver 4.00 >> [?? 12.925254] i5500_temp 0000:00:14.3: Sensor seems to be disabled >> [?? 13.104195] ipmi_si IPI0001:00: Found new BMC (man_id: 0x001043, >> prod_id: 0x0943, dev_id: 0x20) >> [?? 13.149790] ipmi_si IPI0001:00: IPMI kcs interface initialized >> [?? 13.183524] IPMI SSIF Interface driver >> [?? 13.507575] kvm: VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL does not work >> properly. Using workaround >> [?? 13.976182] EXT4-fs (dm-1): mounted filesystem with ordered data >> mode. Opts: barrier=1 >> [?? 14.199828] EXT4-fs (dm-2): mounted filesystem with ordered data >> mode. Opts: barrier=1 >> [?? 14.687189] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready >> [?? 17.263617] Process accounting resumed >> [?? 17.794359] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow >> Control: None >> [?? 17.794714] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready >> [?? 22.936455] e1000e 0000:02:00.0 eth1: changing MTU from 1500 to 9000 >> [?? 23.033336] e1000e 0000:02:00.0: Some CPU C-states have been >> disabled in order to enable jumbo frames >> [?? 26.102364] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow >> Control: None >> [?? 27.174495] 8021q: 802.1Q VLAN Support v1.8 >> [?? 27.174513] 8021q: adding VLAN 0 to HW filter on device eth1 >> [?? 30.671724] cgroup: cgroup: disabling cgroup2 socket matching due >> to net_prio or net_cls activation >> [?? 30.898564] netpoll: netconsole: local port 6666 >> [?? 30.898566] netpoll: netconsole: local IPv6 address >> 2a02:6b8:0:80b:beae:c5ff:fe28:23f8 >> [?? 30.898567] netpoll: netconsole: interface 'eth1' >> [?? 30.898568] netpoll: netconsole: remote port 6666 >> [?? 30.898568] netpoll: netconsole: remote IPv6 address >> 2a02:6b8:b000:605c:e61d:2dff:fe03:3790 >> [?? 30.898569] netpoll: netconsole: remote ethernet address >> b0:a8:6e:f4:ff:c0 >> [?? 30.917747] console [netcon0] enabled >> [?? 30.917749] netconsole: network logging started >> [?? 31.453353] e1000e 0000:02:00.0: Some CPU C-states have been >> disabled in order to enable jumbo frames >> [?? 34.185730] e1000e 0000:02:00.0: Some CPU C-states have been >> disabled in order to enable jumbo frames >> [?? 34.321840] e1000e 0000:02:00.0: Some CPU C-states have been >> disabled in order to enable jumbo frames >> [?? 34.465822] e1000e 0000:02:00.0: Some CPU C-states have been >> disabled in order to enable jumbo frames >> [?? 34.597423] e1000e 0000:02:00.0: Some CPU C-states have been >> disabled in order to enable jumbo frames >> [?? 34.745417] e1000e 0000:02:00.0: Some CPU C-states have been >> disabled in order to enable jumbo frames >> [?? 34.877356] e1000e 0000:02:00.0: Some CPU C-states have been >> disabled in order to enable jumbo frames >> [?? 35.005441] e1000e 0000:02:00.0: Some CPU C-states have been >> disabled in order to enable jumbo frames >> [?? 35.157376] e1000e 0000:02:00.0: Some CPU C-states have been >> disabled in order to enable jumbo frames >> [?? 35.289362] e1000e 0000:02:00.0: Some CPU C-states have been >> disabled in order to enable jumbo frames >> [?? 35.417441] e1000e 0000:02:00.0: Some CPU C-states have been >> disabled in order to enable jumbo frames >> [?? 37.790342] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow >> Control: None >> > > > _______________________________________________ > Intel-wired-lan mailing list > Intel-wired-lan at osuosl.org > https://lists.osuosl.org/mailman/listinfo/intel-wired-lan