From: Jacob Keller <jacob.e.keller@intel.com>
To: <intel-wired-lan@osuosl.org>
Subject: Re: [Intel-wired-lan] [PATCH net v1] i40e: fix xdp_redirect logs error message when testing with MTU=1500
Date: Mon, 17 Oct 2022 13:26:33 -0700 [thread overview]
Message-ID: <a8acb463-5061-72c8-6322-ecb46d77deff@intel.com> (raw)
In-Reply-To: <20221014100232.410542-1-mateusz.palczewski@intel.com>
On 10/14/2022 3:02 AM, Mateusz Palczewski wrote:
> From: Bartosz Staszewski <bartoszx.staszewski@intel.com>
>
> The driver is currently logging an error message "MTU too large to enable XDP"
> when trying to enable XDP on totally normal MTU.
>
> This was caused by whenever the interface was down, function
> i40e_xdp was passing vsi->rx_buf_len field to i40e_xdp_setup()
> which was equal 0. i40e_open() then calls i40e_vsi_configure_rx()
> which configures that field, but that only happens when interface is up.
> When it is down, i40e_open() is not being called, thusvsi->rx_buf_len
> which causes the bug is not set.
>
> Solution for this is calculate buffer length in newly created
> function - i40e_calculate_vsi_rx_buf_len() that return actual buffer
> length. Buffer length is being calculated based on the same rules applied
> previously in i40e_vsi_configure_rx() function.
>
> Fixes: 613142b0bb88 ("i40e: Log error for oversized MTU on device")
> Signed-off-by: Bartosz Staszewski <bartoszx.staszewski@intel.com>
> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
> ---
> drivers/net/ethernet/intel/i40e/i40e_main.c | 42 +++++++++++++++------
> 1 file changed, 30 insertions(+), 12 deletions(-)
>
> diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
> index b5dcd15ced36..2fec0cff282c 100644
> --- a/drivers/net/ethernet/intel/i40e/i40e_main.c
> +++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
> @@ -3693,6 +3693,30 @@ static int i40e_vsi_configure_tx(struct i40e_vsi *vsi)
> return err;
> }
>
> +/**
> + * i40e_calculate_vsi_rx_buf_len - Calculates buffer length
> + *
> + * @vsi: VSI to calculate rx_buf_len from
> + */
> +static u16 i40e_calculate_vsi_rx_buf_len(struct i40e_vsi *vsi)
> +{
> + u16 ret;
> +
> + if (!vsi->netdev || (vsi->back->flags & I40E_FLAG_LEGACY_RX)) {
> + ret = I40E_RXBUFFER_2048;
> +#if (PAGE_SIZE < 8192)
> + } else if (!I40E_2K_TOO_SMALL_WITH_PADDING &&
> + (vsi->netdev->mtu <= ETH_DATA_LEN)) {
This has a checkpatch error here because of the unnecessary parenthesis.
I can fix this up locally when applying the patch to net-queue.
Thanks,
Jake
> + ret = I40E_RXBUFFER_1536 - NET_IP_ALIGN;
> +#endif
> + } else {
> + ret = (PAGE_SIZE < 8192) ? I40E_RXBUFFER_3072 :
> + I40E_RXBUFFER_2048;
> + }
> +
> + return ret;
> +}
> +
> /**
> * i40e_vsi_configure_rx - Configure the VSI for Rx
> * @vsi: the VSI being configured
> @@ -3704,20 +3728,14 @@ static int i40e_vsi_configure_rx(struct i40e_vsi *vsi)
> int err = 0;
> u16 i;
>
> - if (!vsi->netdev || (vsi->back->flags & I40E_FLAG_LEGACY_RX)) {
> - vsi->max_frame = I40E_MAX_RXBUFFER;
> - vsi->rx_buf_len = I40E_RXBUFFER_2048;
> + vsi->max_frame = I40E_MAX_RXBUFFER;
> + vsi->rx_buf_len = i40e_calculate_vsi_rx_buf_len(vsi);
> +
> #if (PAGE_SIZE < 8192)
> - } else if (!I40E_2K_TOO_SMALL_WITH_PADDING &&
> - (vsi->netdev->mtu <= ETH_DATA_LEN)) {
> + if (vsi->netdev && !I40E_2K_TOO_SMALL_WITH_PADDING &&
> + (vsi->netdev->mtu <= ETH_DATA_LEN))
> vsi->max_frame = I40E_RXBUFFER_1536 - NET_IP_ALIGN;
> - vsi->rx_buf_len = I40E_RXBUFFER_1536 - NET_IP_ALIGN;
> #endif
> - } else {
> - vsi->max_frame = I40E_MAX_RXBUFFER;
> - vsi->rx_buf_len = (PAGE_SIZE < 8192) ? I40E_RXBUFFER_3072 :
> - I40E_RXBUFFER_2048;
> - }
>
> /* set up individual rings */
> for (i = 0; i < vsi->num_queue_pairs && !err; i++)
> @@ -13265,7 +13283,7 @@ static int i40e_xdp_setup(struct i40e_vsi *vsi, struct bpf_prog *prog,
> int i;
>
> /* Don't allow frames that span over multiple buffers */
> - if (frame_size > vsi->rx_buf_len) {
> + if (frame_size > i40e_calculate_vsi_rx_buf_len(vsi)) {
> NL_SET_ERR_MSG_MOD(extack, "MTU too large to enable XDP");
> return -EINVAL;
> }
_______________________________________________
Intel-wired-lan mailing list
Intel-wired-lan@osuosl.org
https://lists.osuosl.org/mailman/listinfo/intel-wired-lan
next prev parent reply other threads:[~2022-10-17 20:26 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-10-14 10:02 [Intel-wired-lan] [PATCH net v1] i40e: fix xdp_redirect logs error message when testing with MTU=1500 Mateusz Palczewski
2022-10-17 20:26 ` Jacob Keller [this message]
2022-11-11 11:16 ` Nagaraju, Shwetha
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=a8acb463-5061-72c8-6322-ecb46d77deff@intel.com \
--to=jacob.e.keller@intel.com \
--cc=intel-wired-lan@osuosl.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox