From: Nemesa Garg <nemesa.garg@intel.com>
To: intel-gfx@lists.freedesktop.org, intel-xe@lists.freedesktop.org
Cc: chaitanya.kumar.borah@intel.com, Nemesa Garg <nemesa.garg@intel.com>
Subject: [PATCH v7 3/5] drm/i915/cursor: Handle secondary cursor state
Date: Thu, 27 Aug 2026 22:12:01 +0530 [thread overview]
Message-ID: <20260827164203.2371794-4-nemesa.garg@intel.com> (raw)
In-Reply-To: <20260827164203.2371794-1-nemesa.garg@intel.com>
In joiner mode the fast path cursor update must handle
secondary pipes. Iterate over all joined pipes uniformly
to duplicate plane state, run check_plane(), pin the
framebuffer and on success swap in the new plane state
for each secondary cursor.
Track every successfully prepared pipe in a joined_pipe_state[] array
of struct intel_cursor_joiner_state so that later frontbuffer, unpin
and error-cleanup paths treat primary and secondaries uniformly,
and ensures the primary's pinned framebuffer is released if a
secondary fails partway through.
Convert the primary-only vblank unpin block into a loop over the
joined_pipe_state[] array so each pipe's old cursor framebuffer is scheduled for
unpin (or unpinned inline when unchanged) independently. All unpin
work is armed on the primary crtc's vblank (&crtc->base), consistent
with the single primary vblank evasion used above.
v2: Use intel_crtc_joined_pipe_mask(). [Ville]
Add locking mechanism. [Ville]
v3: Drop the per-pipe fastpath mutex array. [sashiko]
v4: Fold parallel arrays into struct intel_cursor_joiner_state joined_pipe_state[].
unify primary/secondary in a single loop.
use bare check_plane(). [Chaitanya]
v5: Fix secondary uapi.crtc to each pipe's own crtc.
Rename intel_cursor_pipe to intel_cursor_joiner_state and
joined[] to joined_pipe_state[]. [Chaitanya]
v6: Mirror primary uapi into secondary hw state, don't set uapi.crtc. [sashiko]
v7: Squash patch 5 with this patch. [Chaitanya]
Assisted-by: Claude:claude-sonnet-4.6
Signed-off-by: Nemesa Garg <nemesa.garg@intel.com>
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
---
drivers/gpu/drm/i915/display/intel_cursor.c | 181 +++++++++++++-------
1 file changed, 120 insertions(+), 61 deletions(-)
diff --git a/drivers/gpu/drm/i915/display/intel_cursor.c b/drivers/gpu/drm/i915/display/intel_cursor.c
index b57b446b9788..e4a7d4d2915a 100644
--- a/drivers/gpu/drm/i915/display/intel_cursor.c
+++ b/drivers/gpu/drm/i915/display/intel_cursor.c
@@ -847,6 +847,7 @@ intel_cursor_joiner_commits_idle(struct intel_display *display,
static void
intel_cursor_fastpath_update_plane_state(struct intel_plane_state *plane_state,
+ const struct intel_plane_state *from_plane_state,
struct drm_framebuffer *fb,
struct intel_crtc *hw_crtc,
int crtc_x, int crtc_y,
@@ -854,20 +855,34 @@ intel_cursor_fastpath_update_plane_state(struct intel_plane_state *plane_state,
u32 src_x, u32 src_y,
u32 src_w, u32 src_h)
{
- drm_atomic_set_fb_for_plane(&plane_state->uapi, fb);
-
- plane_state->uapi.src_x = src_x;
- plane_state->uapi.src_y = src_y;
- plane_state->uapi.src_w = src_w;
- plane_state->uapi.src_h = src_h;
- plane_state->uapi.crtc_x = crtc_x;
- plane_state->uapi.crtc_y = crtc_y;
- plane_state->uapi.crtc_w = crtc_w;
- plane_state->uapi.crtc_h = crtc_h;
-
- intel_plane_copy_uapi_to_hw_state(NULL, plane_state, plane_state, hw_crtc);
+ /*
+ * Only the primary owns its uapi state; a secondary mirrors it, so
+ * its uapi.crtc/fb stay NULL and hw.crtc comes from hw_crtc.
+ */
+ if (plane_state == from_plane_state) {
+ drm_atomic_set_fb_for_plane(&plane_state->uapi, fb);
+
+ plane_state->uapi.src_x = src_x;
+ plane_state->uapi.src_y = src_y;
+ plane_state->uapi.src_w = src_w;
+ plane_state->uapi.src_h = src_h;
+ plane_state->uapi.crtc_x = crtc_x;
+ plane_state->uapi.crtc_y = crtc_y;
+ plane_state->uapi.crtc_w = crtc_w;
+ plane_state->uapi.crtc_h = crtc_h;
+ }
+
+ intel_plane_copy_uapi_to_hw_state(NULL, plane_state, from_plane_state, hw_crtc);
}
+struct intel_cursor_joiner_state {
+ struct intel_plane *plane;
+ struct intel_crtc *crtc;
+ struct intel_crtc_state *crtc_state;
+ struct intel_plane_state *old_plane_state;
+ struct intel_plane_state *new_plane_state;
+};
+
static int
intel_legacy_cursor_update(struct drm_plane *_plane,
struct drm_crtc *_crtc,
@@ -883,11 +898,12 @@ intel_legacy_cursor_update(struct drm_plane *_plane,
struct intel_display *display = to_intel_display(plane);
struct intel_plane_state *old_plane_state =
to_intel_plane_state(plane->base.state);
- struct intel_plane_state *new_plane_state;
struct intel_crtc_state *crtc_state =
to_intel_crtc_state(crtc->base.state);
- struct intel_crtc_state *new_crtc_state;
struct intel_vblank_evade_ctx evade;
+ struct intel_cursor_joiner_state joined_pipe_state[I915_MAX_PIPES] = {};
+ struct intel_crtc *pipe_crtc;
+ int num_pipes = 0;
int ret;
/*
@@ -933,38 +949,68 @@ intel_legacy_cursor_update(struct drm_plane *_plane,
if (!intel_cursor_joiner_commits_idle(display, crtc_state))
goto slow;
- new_plane_state = to_intel_plane_state(intel_plane_duplicate_state(&plane->base));
- if (!new_plane_state)
- return -ENOMEM;
-
- new_crtc_state = to_intel_crtc_state(intel_crtc_duplicate_state(&crtc->base));
- if (!new_crtc_state) {
- ret = -ENOMEM;
- goto out_free;
- }
+ /*
+ * Iterate over all joined pipes (primary and secondary) uniformly.
+ * The joined pipe mask includes both the primary pipe and all
+ * secondary joiner pipes, allowing us to handle them all the same way.
+ */
+ for_each_intel_crtc_in_pipe_mask(display, pipe_crtc,
+ intel_crtc_joined_pipe_mask(crtc_state)) {
+ struct intel_cursor_joiner_state *j = &joined_pipe_state[num_pipes];
+
+ j->plane = intel_crtc_get_plane(pipe_crtc, PLANE_CURSOR);
+ j->crtc = pipe_crtc;
+ j->crtc_state = to_intel_crtc_state(pipe_crtc->base.state);
+ j->old_plane_state = to_intel_plane_state(j->plane->base.state);
+ j->new_plane_state =
+ to_intel_plane_state(intel_plane_duplicate_state(&j->plane->base));
+
+ if (!j->new_plane_state) {
+ ret = -ENOMEM;
+ goto out_free;
+ }
- intel_cursor_fastpath_update_plane_state(new_plane_state, fb,
- crtc,
- crtc_x, crtc_y, crtc_w, crtc_h,
- src_x, src_y, src_w, src_h);
+ intel_cursor_fastpath_update_plane_state(j->new_plane_state,
+ joined_pipe_state[0].new_plane_state,
+ fb, pipe_crtc,
+ crtc_x, crtc_y,
+ crtc_w, crtc_h,
+ src_x, src_y,
+ src_w, src_h);
+
+ ret = j->plane->check_plane(j->crtc_state, j->new_plane_state);
+ if (ret) {
+ intel_plane_destroy_state(&j->plane->base,
+ &j->new_plane_state->uapi);
+ goto out_free;
+ }
- ret = intel_plane_atomic_check_with_state(crtc_state, new_crtc_state,
- old_plane_state, new_plane_state);
- if (ret)
- goto out_free;
+ ret = intel_plane_pin_fb(j->new_plane_state, j->old_plane_state);
+ if (ret) {
+ intel_plane_destroy_state(&j->plane->base,
+ &j->new_plane_state->uapi);
+ goto out_free;
+ }
- ret = intel_plane_pin_fb(new_plane_state, old_plane_state);
- if (ret)
- goto out_free;
+ num_pipes++;
+ }
- intel_frontbuffer_flush(to_intel_frontbuffer(new_plane_state->hw.fb),
+ intel_frontbuffer_flush(to_intel_frontbuffer(joined_pipe_state[0].new_plane_state->hw.fb),
ORIGIN_CURSOR_UPDATE);
- intel_frontbuffer_track(to_intel_frontbuffer(old_plane_state->hw.fb),
- to_intel_frontbuffer(new_plane_state->hw.fb),
- plane->frontbuffer_bit);
- /* Swap plane state */
- plane->base.state = &new_plane_state->uapi;
+ for (int i = 0; i < num_pipes; i++)
+ intel_frontbuffer_track(to_intel_frontbuffer(joined_pipe_state[i].old_plane_state->hw.fb),
+ to_intel_frontbuffer(joined_pipe_state[i].new_plane_state->hw.fb),
+ joined_pipe_state[i].plane->frontbuffer_bit);
+
+ for (int i = 0; i < num_pipes; i++) {
+ joined_pipe_state[i].plane->base.state = &joined_pipe_state[i].new_plane_state->uapi;
+
+ if (joined_pipe_state[i].new_plane_state->uapi.visible)
+ joined_pipe_state[i].crtc_state->active_planes |= BIT(PLANE_CURSOR);
+ else
+ joined_pipe_state[i].crtc_state->active_planes &= ~BIT(PLANE_CURSOR);
+ }
/*
* We cannot swap crtc_state as it may be in use by an atomic commit or
@@ -976,7 +1022,6 @@ intel_legacy_cursor_update(struct drm_plane *_plane,
* planes atomically. If the cursor was part of the atomic update then
* we would have taken the slowpath.
*/
- crtc_state->active_planes = new_crtc_state->active_planes;
intel_vblank_evade_init(crtc_state, crtc_state, &evade);
@@ -998,9 +1043,11 @@ intel_legacy_cursor_update(struct drm_plane *_plane,
local_irq_disable();
}
- if (new_plane_state->uapi.visible) {
- intel_plane_update_noarm(NULL, plane, crtc_state, new_plane_state);
- intel_plane_update_arm(NULL, plane, crtc_state, new_plane_state);
+ if (joined_pipe_state[0].new_plane_state->uapi.visible) {
+ intel_plane_update_noarm(NULL, plane, crtc_state,
+ joined_pipe_state[0].new_plane_state);
+ intel_plane_update_arm(NULL, plane, crtc_state,
+ joined_pipe_state[0].new_plane_state);
} else {
intel_plane_disable_arm(NULL, plane, crtc_state);
}
@@ -1009,26 +1056,38 @@ intel_legacy_cursor_update(struct drm_plane *_plane,
intel_psr_unlock(crtc_state);
- if (old_plane_state->ggtt_vma != new_plane_state->ggtt_vma) {
- drm_vblank_work_init(&old_plane_state->unpin_work, &crtc->base,
- intel_cursor_unpin_work);
-
- drm_vblank_work_schedule(&old_plane_state->unpin_work,
- drm_crtc_accurate_vblank_count(&crtc->base) + 1,
- false);
-
- old_plane_state = NULL;
- } else {
- intel_plane_unpin_fb(old_plane_state);
+ /*
+ * Schedule or immediately unpin old framebuffers.
+ * Protect against concurrent access.
+ */
+ for (int i = 0; i < num_pipes; i++) {
+ struct intel_plane_state *old = joined_pipe_state[i].old_plane_state;
+
+ if (old->ggtt_vma != joined_pipe_state[i].new_plane_state->ggtt_vma) {
+ drm_vblank_work_init(&old->unpin_work, &crtc->base,
+ intel_cursor_unpin_work);
+ drm_vblank_work_schedule(&old->unpin_work,
+ drm_crtc_accurate_vblank_count(&crtc->base) + 1,
+ false);
+ joined_pipe_state[i].old_plane_state = NULL;
+ } else {
+ intel_plane_unpin_fb(old);
+ }
}
out_free:
- if (new_crtc_state)
- intel_crtc_destroy_state(&crtc->base, &new_crtc_state->uapi);
- if (ret)
- intel_plane_destroy_state(&plane->base, &new_plane_state->uapi);
- else if (old_plane_state)
- intel_plane_destroy_state(&plane->base, &old_plane_state->uapi);
+ if (ret) {
+ for (int i = 0; i < num_pipes; i++) {
+ intel_plane_unpin_fb(joined_pipe_state[i].new_plane_state);
+ intel_plane_destroy_state(&joined_pipe_state[i].plane->base,
+ &joined_pipe_state[i].new_plane_state->uapi);
+ }
+ } else {
+ for (int i = 0; i < num_pipes; i++)
+ if (joined_pipe_state[i].old_plane_state)
+ intel_plane_destroy_state(&joined_pipe_state[i].plane->base,
+ &joined_pipe_state[i].old_plane_state->uapi);
+ }
return ret;
slow:
--
2.25.1
next prev parent reply other threads:[~2026-08-27 16:44 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-08-27 16:41 [PATCH 0/5] Enable joiner cursor fast updates Nemesa Garg
2026-08-27 16:41 ` [PATCH 1/5] drm/i915/cursor: Check joiner cursor commit status Nemesa Garg
2026-08-27 16:42 ` [PATCH 2/5] drm/i915/cursor: Add helper to update cursor plane Nemesa Garg
2026-08-27 16:42 ` Nemesa Garg [this message]
2026-08-28 10:26 ` [PATCH v7 3/5] drm/i915/cursor: Handle secondary cursor state Borah, Chaitanya Kumar
2026-08-28 11:21 ` Garg, Nemesa
2026-08-27 16:42 ` [PATCH 4/5] drm/i915/cursor: Program secondary cursor planes Nemesa Garg
2026-08-27 16:42 ` [PATCH 5/5] drm/i915/cursor: Allow joiner cursor fast path update Nemesa Garg
2026-08-27 16:51 ` ✗ CI.checkpatch: warning for Enable joiner cursor fast updates (rev7) Patchwork
2026-08-27 16:52 ` ✓ CI.KUnit: success " Patchwork
2026-08-27 17:47 ` ✗ Xe.CI.BAT: failure " Patchwork
2026-08-28 3:27 ` Garg, Nemesa
2026-08-27 19:01 ` ✗ Xe.CI.FULL: " Patchwork
2026-08-28 3:28 ` Garg, Nemesa
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260827164203.2371794-4-nemesa.garg@intel.com \
--to=nemesa.garg@intel.com \
--cc=chaitanya.kumar.borah@intel.com \
--cc=intel-gfx@lists.freedesktop.org \
--cc=intel-xe@lists.freedesktop.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox