Error in "Executing all Device _STA and_INI methods"

Error in "Executing all Device _STA and_INI methods"

[olm-acpi-devel-+d40ctR3GU7QT0dZR+AlfA]

Hello,

I hope this is the correct list for this question.

I have a Gateway 400VTX laptop. It has a 2.2 GHz Celeron CPU.  I just
compiled and installed Linux 2.6.1 on it. I chose the "Intel P4/Xeon"
option (CONFIG_MPENTIUM4=y) from configuration. I have enabled APCI
but not APM.

I'm checking my dmesg and noticed some errors:

Executing all Device _STA and_INI methods:......evregion-0249 [21] ev_address_space_dispa: no handler for region(c12db5a8) [EmbeddedControl]
 exfldio-0282 [20] ex_access_region      : Region EmbeddedControl(3) has no handler
 dswexec-0422 [13] ds_exec_end_op        : [LGreater]: Could not resolve operands, AE_NOT_EXIST
 psparse-1120: *** Error: Method execution failed [\_SB_.PCI0._INI] (Node c12e06a8), AE_NOT_EXIST
  nsinit-0397 [06] ns_init_one_device    : \_SB_.PCI0._INI failed: AE_NOT_EXIST

What does this mean? Don't seem to be able to put the machine to any
of the reduced states. The following commands produce nothing:

  echo "standby" > state
  echo "mem" > state
  echo "disk" > /sys/power/stat

It seems that the laptop is running too hot. I can feel the heat and
I don't know if this is 'acceptable' or not. Also, I get a lot of
lines line this in my dmesg:

[ACPI Debug] String: Temperature increasing: _Q80


Thanks in advance for your help.

Regards,

Ovanes

P.S. What follows is the portions of my dmesg which I found relevant
to APCI, up to the point where the error is printed.


ACPI: RSDP (v000 GATEWA                                    ) @ 0x000f6710
ACPI: RSDT (v001 GATEWA 400VTX   0x20030312  LTP 0x00000000) @ 0x0f6e6d53
ACPI: FADT (v001 GATEWA 400VTX   0x20030312 PTL  0x00000050) @ 0x0f6ebf64
ACPI: BOOT (v001 GATEWA 400VTX   0x20030312  LTP 0x00000001) @ 0x0f6ebfd8
ACPI: DSDT (v001 GATEWA 400VTX   0x20030312 MSFT 0x0100000e) @ 0x00000000
CPU:     After generic identify, caps: bfebf9ff 00000000 00000000 00000000
CPU:     After vendor identify, caps: bfebf9ff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 256K
CPU:     After all inits, caps: bfebf9ff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU#0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU: Intel Mobile Intel(R) Celeron(R) CPU 2.20GHz stepping 07
ACPI: Subsystem revision 20031002
 tbxface-0117 [03] acpi_load_tables      : ACPI Tables successfully acquired
Parsing all Control Methods:.................................................................................................................................................................................................
Table [DSDT](id F004) - 685 Objects with 55 Devices 193 Methods 15 Regions
ACPI Namespace successfully loaded at root c03c6cfc
ACPI: IRQ 9 was Edge Triggered, setting to Level Triggerd
evxfevnt-0093 [04] acpi_enable           : Transition to ACPI mode successful
evgpeblk-0748 [06] ev_create_gpe_block   : GPE 00 to 31 [_GPE] 4 regs at 0000000000001028 on int 9Completing Region/Field/Buffer/Package initialization:.................................................................
Initialized 15/15 Regions 0/0 Fields 28/28 Buffers 22/22 Packages (693 nodes)
Executing all Device _STA and_INI methods:......evregion-0249 [21] ev_address_space_dispa: no handler for region(c12db5a8) [EmbeddedControl]
 exfldio-0282 [20] ex_access_region      : Region EmbeddedControl(3) has no handler
 dswexec-0422 [13] ds_exec_end_op        : [LGreater]: Could not resolve operands, AE_NOT_EXIST
 psparse-1120: *** Error: Method execution failed [\_SB_.PCI0._INI] (Node c12e06a8), AE_NOT_EXIST
  nsinit-0397 [06] ns_init_one_device    : \_SB_.PCI0._INI failed: AE_NOT_EXIST
..................................................
56 Devices found containing: 56 _STA, 0 _INI methods
ACPI: Interpreter enabled


-------------------------------------------------------
The SF.Net email is sponsored by EclipseCon 2004
Premiere Conference on Open Tools Development and Integration
See the breadth of Eclipse activity. February 3-5 in Anaheim, CA.
http://www.eclipsecon.org/osdn

Re: Error in "Executing all Device _STA and_INI methods"

[Greg Sarjeant]

Hello,

Gateway laptops do not seem to provide an ECDT. You may want to try this
patch:
http://bugzilla.kernel.org/attachment.cgi?id=1690&action=view

It fixed similar issues on my Gateway 200X, and I have seen reports that
it also fixes the issue on the Gateway M350.

Here is the corresponding bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=1690

Greg


On Tue, 2004-01-20 at 10:37, olm-acpi-devel-+d40ctR3GU7QT0dZR+AlfA@public.gmane.org wrote:
> Hello,
> 
> I hope this is the correct list for this question.
> 
> I have a Gateway 400VTX laptop. It has a 2.2 GHz Celeron CPU.  I just
> compiled and installed Linux 2.6.1 on it. I chose the "Intel P4/Xeon"
> option (CONFIG_MPENTIUM4=y) from configuration. I have enabled APCI
> but not APM.
> 
> I'm checking my dmesg and noticed some errors:
> 
> Executing all Device _STA and_INI methods:......evregion-0249 [21] ev_address_space_dispa: no handler for region(c12db5a8) [EmbeddedControl]
>  exfldio-0282 [20] ex_access_region      : Region EmbeddedControl(3) has no handler
>  dswexec-0422 [13] ds_exec_end_op        : [LGreater]: Could not resolve operands, AE_NOT_EXIST
>  psparse-1120: *** Error: Method execution failed [\_SB_.PCI0._INI] (Node c12e06a8), AE_NOT_EXIST
>   nsinit-0397 [06] ns_init_one_device    : \_SB_.PCI0._INI failed: AE_NOT_EXIST
> 
> What does this mean? Don't seem to be able to put the machine to any
> of the reduced states. The following commands produce nothing:
> 
>   echo "standby" > state
>   echo "mem" > state
>   echo "disk" > /sys/power/stat
> 
> It seems that the laptop is running too hot. I can feel the heat and
> I don't know if this is 'acceptable' or not. Also, I get a lot of
> lines line this in my dmesg:
> 
> [ACPI Debug] String: Temperature increasing: _Q80
> 
> 
> Thanks in advance for your help.
> 
> Regards,
> 
> Ovanes
> 
> P.S. What follows is the portions of my dmesg which I found relevant
> to APCI, up to the point where the error is printed.
> 
> 
> ACPI: RSDP (v000 GATEWA                                    ) @ 0x000f6710
> ACPI: RSDT (v001 GATEWA 400VTX   0x20030312  LTP 0x00000000) @ 0x0f6e6d53
> ACPI: FADT (v001 GATEWA 400VTX   0x20030312 PTL  0x00000050) @ 0x0f6ebf64
> ACPI: BOOT (v001 GATEWA 400VTX   0x20030312  LTP 0x00000001) @ 0x0f6ebfd8
> ACPI: DSDT (v001 GATEWA 400VTX   0x20030312 MSFT 0x0100000e) @ 0x00000000
> CPU:     After generic identify, caps: bfebf9ff 00000000 00000000 00000000
> CPU:     After vendor identify, caps: bfebf9ff 00000000 00000000 00000000
> CPU: Trace cache: 12K uops, L1 D cache: 8K
> CPU: L2 cache: 256K
> CPU:     After all inits, caps: bfebf9ff 00000000 00000000 00000080
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> CPU#0: Intel P4/Xeon Extended MCE MSRs (12) available
> CPU: Intel Mobile Intel(R) Celeron(R) CPU 2.20GHz stepping 07
> ACPI: Subsystem revision 20031002
>  tbxface-0117 [03] acpi_load_tables      : ACPI Tables successfully acquired
> Parsing all Control Methods:.................................................................................................................................................................................................
> Table [DSDT](id F004) - 685 Objects with 55 Devices 193 Methods 15 Regions
> ACPI Namespace successfully loaded at root c03c6cfc
> ACPI: IRQ 9 was Edge Triggered, setting to Level Triggerd
> evxfevnt-0093 [04] acpi_enable           : Transition to ACPI mode successful
> evgpeblk-0748 [06] ev_create_gpe_block   : GPE 00 to 31 [_GPE] 4 regs at 0000000000001028 on int 9Completing Region/Field/Buffer/Package initialization:.................................................................
> Initialized 15/15 Regions 0/0 Fields 28/28 Buffers 22/22 Packages (693 nodes)
> Executing all Device _STA and_INI methods:......evregion-0249 [21] ev_address_space_dispa: no handler for region(c12db5a8) [EmbeddedControl]
>  exfldio-0282 [20] ex_access_region      : Region EmbeddedControl(3) has no handler
>  dswexec-0422 [13] ds_exec_end_op        : [LGreater]: Could not resolve operands, AE_NOT_EXIST
>  psparse-1120: *** Error: Method execution failed [\_SB_.PCI0._INI] (Node c12e06a8), AE_NOT_EXIST
>   nsinit-0397 [06] ns_init_one_device    : \_SB_.PCI0._INI failed: AE_NOT_EXIST
> ..................................................
> 56 Devices found containing: 56 _STA, 0 _INI methods
> ACPI: Interpreter enabled
> 
> 
> -------------------------------------------------------
> The SF.Net email is sponsored by EclipseCon 2004
> Premiere Conference on Open Tools Development and Integration
> See the breadth of Eclipse activity. February 3-5 in Anaheim, CA.
> http://www.eclipsecon.org/osdn
> _______________________________________________
> Acpi-devel mailing list
> Acpi-devel-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org
> https://lists.sourceforge.net/lists/listinfo/acpi-devel
> 



-------------------------------------------------------
The SF.Net email is sponsored by EclipseCon 2004
Premiere Conference on Open Tools Development and Integration
See the breadth of Eclipse activity. February 3-5 in Anaheim, CA.
http://www.eclipsecon.org/osdn

Re: Error in "Executing all Device _STA and_INI methods"

[olm-acpi-devel-+d40ctR3GU7QT0dZR+AlfA]

[-- Attachment #1: Type: TEXT/PLAIN, Size: 6282 bytes --]

I applied the patch to 2.6.1. It compiled with a few warnings.

drivers/acpi/ec.c: In function `acpi_ec_start':
drivers/acpi/ec.c:742: warning: implicit declaration of function `acpi_ns_evaluate_relative'
drivers/acpi/ec.c:750: warning: implicit declaration of function `acpi_ns_get_external_pathname'
drivers/acpi/ec.c:750: warning: initialization makes pointer from integer without a cast

It seems to have resolved the error I was having, however, I'm still
not able to control the states.

There is another error, further down:

ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
pci_link-0403 [44] acpi_pci_link_set     : Link disabled
ACPI: Unable to set IRQ for PCI Interrupt Link [LNKE] (likely buggy ACPI BIOS). Aborting ACPI-based IRQ routing. Try pci=noacpi or acpi=off
 pci_irq-0262 [41] acpi_pci_irq_lookup   : Invalid IRQ link routing entry
 pci_irq-0302 [41] acpi_pci_irq_derive   : Unable to derive IRQ for device 0000:02:08.0
ACPI: No IRQ known for interrupt pin A of device 0000:02:08.0
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'

I've attached the full dmesg output.


Ovanes


On Tue, 20 Jan 2004, Greg Sarjeant wrote:

> Hello,
>
> Gateway laptops do not seem to provide an ECDT. You may want to try this
> patch:
> http://bugzilla.kernel.org/attachment.cgi?id=1690&action=view
>
> It fixed similar issues on my Gateway 200X, and I have seen reports that
> it also fixes the issue on the Gateway M350.
>
> Here is the corresponding bug report:
> http://bugzilla.kernel.org/show_bug.cgi?id=1690
>
> Greg
>
>
> On Tue, 2004-01-20 at 10:37, olm-acpi-devel-+d40ctR3GU7QT0dZR+AlfA@public.gmane.org wrote:
> > Hello,
> >
> > I hope this is the correct list for this question.
> >
> > I have a Gateway 400VTX laptop. It has a 2.2 GHz Celeron CPU.  I just
> > compiled and installed Linux 2.6.1 on it. I chose the "Intel P4/Xeon"
> > option (CONFIG_MPENTIUM4=y) from configuration. I have enabled APCI
> > but not APM.
> >
> > I'm checking my dmesg and noticed some errors:
> >
> > Executing all Device _STA and_INI methods:......evregion-0249 [21] ev_address_space_dispa: no handler for region(c12db5a8) [EmbeddedControl]
> >  exfldio-0282 [20] ex_access_region      : Region EmbeddedControl(3) has no handler
> >  dswexec-0422 [13] ds_exec_end_op        : [LGreater]: Could not resolve operands, AE_NOT_EXIST
> >  psparse-1120: *** Error: Method execution failed [\_SB_.PCI0._INI] (Node c12e06a8), AE_NOT_EXIST
> >   nsinit-0397 [06] ns_init_one_device    : \_SB_.PCI0._INI failed: AE_NOT_EXIST
> >
> > What does this mean? Don't seem to be able to put the machine to any
> > of the reduced states. The following commands produce nothing:
> >
> >   echo "standby" > state
> >   echo "mem" > state
> >   echo "disk" > /sys/power/stat
> >
> > It seems that the laptop is running too hot. I can feel the heat and
> > I don't know if this is 'acceptable' or not. Also, I get a lot of
> > lines line this in my dmesg:
> >
> > [ACPI Debug] String: Temperature increasing: _Q80
> >
> >
> > Thanks in advance for your help.
> >
> > Regards,
> >
> > Ovanes
> >
> > P.S. What follows is the portions of my dmesg which I found relevant
> > to APCI, up to the point where the error is printed.
> >
> >
> > ACPI: RSDP (v000 GATEWA                                    ) @ 0x000f6710
> > ACPI: RSDT (v001 GATEWA 400VTX   0x20030312  LTP 0x00000000) @ 0x0f6e6d53
> > ACPI: FADT (v001 GATEWA 400VTX   0x20030312 PTL  0x00000050) @ 0x0f6ebf64
> > ACPI: BOOT (v001 GATEWA 400VTX   0x20030312  LTP 0x00000001) @ 0x0f6ebfd8
> > ACPI: DSDT (v001 GATEWA 400VTX   0x20030312 MSFT 0x0100000e) @ 0x00000000
> > CPU:     After generic identify, caps: bfebf9ff 00000000 00000000 00000000
> > CPU:     After vendor identify, caps: bfebf9ff 00000000 00000000 00000000
> > CPU: Trace cache: 12K uops, L1 D cache: 8K
> > CPU: L2 cache: 256K
> > CPU:     After all inits, caps: bfebf9ff 00000000 00000000 00000080
> > Intel machine check architecture supported.
> > Intel machine check reporting enabled on CPU#0.
> > CPU#0: Intel P4/Xeon Extended MCE MSRs (12) available
> > CPU: Intel Mobile Intel(R) Celeron(R) CPU 2.20GHz stepping 07
> > ACPI: Subsystem revision 20031002
> >  tbxface-0117 [03] acpi_load_tables      : ACPI Tables successfully acquired
> > Parsing all Control Methods:.................................................................................................................................................................................................
> > Table [DSDT](id F004) - 685 Objects with 55 Devices 193 Methods 15 Regions
> > ACPI Namespace successfully loaded at root c03c6cfc
> > ACPI: IRQ 9 was Edge Triggered, setting to Level Triggerd
> > evxfevnt-0093 [04] acpi_enable           : Transition to ACPI mode successful
> > evgpeblk-0748 [06] ev_create_gpe_block   : GPE 00 to 31 [_GPE] 4 regs at 0000000000001028 on int 9Completing Region/Field/Buffer/Package initialization:.................................................................
> > Initialized 15/15 Regions 0/0 Fields 28/28 Buffers 22/22 Packages (693 nodes)
> > Executing all Device _STA and_INI methods:......evregion-0249 [21] ev_address_space_dispa: no handler for region(c12db5a8) [EmbeddedControl]
> >  exfldio-0282 [20] ex_access_region      : Region EmbeddedControl(3) has no handler
> >  dswexec-0422 [13] ds_exec_end_op        : [LGreater]: Could not resolve operands, AE_NOT_EXIST
> >  psparse-1120: *** Error: Method execution failed [\_SB_.PCI0._INI] (Node c12e06a8), AE_NOT_EXIST
> >   nsinit-0397 [06] ns_init_one_device    : \_SB_.PCI0._INI failed: AE_NOT_EXIST
> > ..................................................
> > 56 Devices found containing: 56 _STA, 0 _INI methods
> > ACPI: Interpreter enabled
> >
> >
> > -------------------------------------------------------
> > The SF.Net email is sponsored by EclipseCon 2004
> > Premiere Conference on Open Tools Development and Integration
> > See the breadth of Eclipse activity. February 3-5 in Anaheim, CA.
> > http://www.eclipsecon.org/osdn
> > _______________________________________________
> > Acpi-devel mailing list
> > Acpi-devel-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org
> > https://lists.sourceforge.net/lists/listinfo/acpi-devel
> >
>
>

[-- Attachment #2: Type: TEXT/plain, Size: 12495 bytes --]

Linux version 2.6.1 (root@localhost) (gcc version 3.2.2 20030222 (Red Hat Linux 3.2.2-5)) #14 Tue Jan 20 09:11:04 PST 2004
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved)
 BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000000f6e0000 (usable)
 BIOS-e820: 000000000f6e0000 - 000000000f6ec000 (ACPI data)
 BIOS-e820: 000000000f6ec000 - 000000000f700000 (ACPI NVS)
 BIOS-e820: 000000000f700000 - 0000000010000000 (reserved)
 BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
 BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
246MB LOWMEM available.
On node 0 totalpages: 63200
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 59104 pages, LIFO batch:14
  HighMem zone: 0 pages, LIFO batch:1
DMI present.
ACPI: RSDP (v000 GATEWA                                    ) @ 0x000f6710
ACPI: RSDT (v001 GATEWA 400VTX   0x20030312  LTP 0x00000000) @ 0x0f6e6d53
ACPI: FADT (v001 GATEWA 400VTX   0x20030312 PTL  0x00000050) @ 0x0f6ebf64
ACPI: BOOT (v001 GATEWA 400VTX   0x20030312  LTP 0x00000001) @ 0x0f6ebfd8
ACPI: DSDT (v001 GATEWA 400VTX   0x20030312 MSFT 0x0100000e) @ 0x00000000
Building zonelist for node : 0
Kernel command line: ro root=LABEL=/ hdc=ide-scsi
ide_setup: hdc=ide-scsi
Initializing CPU#0
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 2191.731 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Memory: 246400k/252800k available (1723k kernel code, 5680k reserved, 762k data, 136k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 4325.37 BogoMIPS
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 220k freed
CPU:     After generic identify, caps: bfebf9ff 00000000 00000000 00000000
CPU:     After vendor identify, caps: bfebf9ff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 256K
CPU:     After all inits, caps: bfebf9ff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU#0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU: Intel Mobile Intel(R) Celeron(R) CPU 2.20GHz stepping 07
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd9c2, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20031002
 tbxface-0117 [03] acpi_load_tables      : ACPI Tables successfully acquired
Parsing all Control Methods:.................................................................................................................................................................................................
Table [DSDT](id F004) - 685 Objects with 55 Devices 193 Methods 15 Regions
ACPI Namespace successfully loaded at root c03c6cfc
ACPI: IRQ 9 was Edge Triggered, setting to Level Triggerd
evxfevnt-0093 [04] acpi_enable           : Transition to ACPI mode successful
evgpeblk-0748 [06] ev_create_gpe_block   : GPE 00 to 31 [_GPE] 4 regs at 0000000000001028 on int 9
Completing Region/Field/Buffer/Package initialization:...............................................................
Initialized 13/15 Regions 0/0 Fields 28/28 Buffers 22/22 Packages (693 nodes)
Executing all Device _STA and_INI methods:........................................................
56 Devices found containing: 56 _STA, 1 _INI methods
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs *10)
ACPI: PCI Interrupt Link [LNKC] (IRQs 10)
ACPI: PCI Interrupt Link [LNKD] (IRQs *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 10)
ACPI: PCI Interrupt Link [LNKG] (IRQs 11)
ACPI: PCI Interrupt Link [LNKH] (IRQs *10)
ACPI: Embedded Controller [H_EC] (gpe 29)
ACPI: Power Resource [CFAN] (on)
ACPI: Power Resource [CFN2] (off)
ACPI: Power Resource [CFN3] (on)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: the driver 'system' has been registered
[ACPI Debug] String: Temperature increasing: _Q80
[ACPI Debug] String: Temperature increasing: _Q80
SCSI subsystem initialized
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
pci_link-0403 [44] acpi_pci_link_set     : Link disabled
ACPI: Unable to set IRQ for PCI Interrupt Link [LNKE] (likely buggy ACPI BIOS). Aborting ACPI-based IRQ routing. Try pci=noacpi or acpi=off
 pci_irq-0262 [41] acpi_pci_irq_lookup   : Invalid IRQ link routing entry
 pci_irq-0302 [41] acpi_pci_irq_derive   : Unable to derive IRQ for device 0000:02:08.0
ACPI: No IRQ known for interrupt pin A of device 0000:02:08.0
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
SBF: Simple Boot Flag extension found and enabled.
SBF: Setting boot flags 0x1
Machine check exception polling timer started.
ikconfig 0.7 with /proc/config*
VFS: Disk quotas dquot_6.5.1
NTFS driver 2.1.5 [Flags: R/W].
Initializing Cryptographic API
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pty: 2048 Unix98 ptys configured
Real Time Clock Driver v1.12
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
pnp: the driver 'serial' has been registered
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: TOSHIBA MK3021GAS, ATA DISK drive
hdc: QSI CD-RW/DVD-ROM SBW-242, ATAPI CD/DVD-ROM drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
[ACPI Debug] String: Temperature increasing: _Q80
hda: 58605120 sectors (30005 MB), CHS=58140/16/63
 hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 >
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
Synaptics Touchpad, model: 1
 Firmware: 5.9
 Sensor: 28
 new absolute packet format
 Touchpad has extended capability bits
 -> four buttons
 -> multifinger detection
 -> palm detection
input: SynPS/2 Synaptics TouchPad on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
PM: Reading pmdisk image.
PM: Resume from disk failed.
ACPI: (supports S0 S3 S4 S5)
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 136k freed
spurious 8259A interrupt: IRQ7.
NET: Registered protocol family 1
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 10, pci mem d0018000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-13
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
hub 1-0:1.0: new USB device on port 3, assigned address 2
EXT3 FS on hda7, internal journal
Adding 265032k swap on /dev/hda9.  Priority:-1 extents:1
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
  Vendor: USB2.0    Model: CardReader CF RW  Rev: 0.0>
  Type:   Direct-Access                      ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
drivers/usb/core/usb.c: registered new driver usb-storage
USB Mass Storage support registered.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda10, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NTFS volume version 3.1.
kudzu: numerical sysctl 1 23 is obsolete.
pnp: the driver 'parport_pc' has been registered
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
request_module: failed /sbin/modprobe -- block-major-2-0. error = 256
ip_tables: (C) 2000-2002 Netfilter core team
NET: Registered protocol family 17
Intel(R) PRO/100 Network Driver - version 2.3.30-k1
Copyright (c) 2003 Intel Corporation

pci_link-0403 [47] acpi_pci_link_set     : Link disabled
ACPI: Unable to set IRQ for PCI Interrupt Link [LNKE] (likely buggy ACPI BIOS). Aborting ACPI-based IRQ routing. Try pci=noacpi or acpi=off
 pci_irq-0262 [44] acpi_pci_irq_lookup   : Invalid IRQ link routing entry
 pci_irq-0302 [44] acpi_pci_irq_derive   : Unable to derive IRQ for device 0000:02:08.0
ACPI: No IRQ known for interrupt pin A of device 0000:02:08.0
e100: selftest OK.
e100: eth0: Intel(R) PRO/100 Network Connection
  Hardware receive checksums enabled

Linux Kernel Card Services
  options:  [pci] [cardbus] [pm]
Yenta: CardBus bridge found at 0000:02:02.0 [107b:0402]
Yenta: ISA IRQ mask 0x00b8, PCI irq 11
Socket status: 30000411
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x3c0-0x3df 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
orinoco.c 0.13e (David Gibson <hermes@gibson.dropbear.id.au> and others)
orinoco_cs.c 0.13e (David Gibson <hermes@gibson.dropbear.id.au> and others)
eth1: Station identity 001f:0002:0001:0004
eth1: Looks like an Intersil firmware version 1.4.2
eth1: Ad-hoc demo mode supported
eth1: IEEE standard IBSS ad-hoc mode supported
eth1: WEP supported, 104-bit key
eth1: MAC address 00:06:25:11:06:52
eth1: Station name "Prism  I"
eth1: ready
eth1: index 0x01: Vcc 5.0, irq 3, io 0x0100-0x013f
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0: clocking to 48000
request_module: failed /sbin/modprobe -- snd-card-1. error = 256
request_module: failed /sbin/modprobe -- char-major-10-134. error = 256
Linux agpgart interface v0.100 (c) Dave Jones
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
[ACPI Debug] String: Temperature increasing: _Q80