public inbox for linux-acpi@vger.kernel.org
 help / color / mirror / Atom feed
* Fw: Anybody? 2.6.11 (stable and -rc) ACPI breaks USB
@ 2005-03-05  7:46 Andrew Morton
       [not found] ` <20050304234622.63e8a335.akpm-3NddpPZAyC0@public.gmane.org>
  0 siblings, 1 reply; 26+ messages in thread
From: Andrew Morton @ 2005-03-05  7:46 UTC (permalink / raw)
  To: acpi-devel-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f; +Cc: Grzegorz Kulewski



Begin forwarded message:

Date: Fri, 4 Mar 2005 21:40:19 +0100 (CET)
From: Grzegorz Kulewski <kangur-ghbW0t/Qn0CsTnJN9+BGXg@public.gmane.org>
To: linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Subject: Anybody? 2.6.11 (stable and -rc) ACPI breaks USB


[ I posted it before but nobody anwsered... ]

Hi,

I just installed 2.6.11 and I was hit by the same bug (or feature?) I found in 
-rcs. Basically my USB will work only if acpi=off was passed to the kernel. It 
looks like without acpi=off it will assign IRQ 10 and with acpi=off it will 
assign IRQ9. It worked at least with 2.6.9. I do not know if the USB is 
completly broken but at least my speedtouch modem will not work (the red led 
will be on for some time then completly black).


My lspci -vvv (2.6.11 with acpi=off):
# lspci -vvv
0000:00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-760 [IGD4-1P] System 
Controller (rev 13)
         Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort+ >SERR- <PERR-
  Latency: 32
  Region 0: Memory at f0000000 (32-bit, prefetchable)
  Region 1: Memory at f7003000 (32-bit, prefetchable) [size=4K]
  Region 2: I/O ports at c000 [disabled] [size=4]
  Capabilities: [a0] AGP version 2.0
                 Status: RQ=16 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 
64bit- FW+ AGP3- Rate=x1,x2,x4
                 Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW+ 
Rate=x4

0000:00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-760 [IGD4-1P] AGP 
Bridge (prog-if 00 [Normal decode])
         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR+ FastB2B-
         Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
  Latency: 32
  Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
  I/O behind bridge: 0000f000-00000fff
  Memory behind bridge: f4000000-f5ffffff
  Prefetchable memory behind bridge: e8000000-efffffff
  BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-

0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] 
(rev 40)
  Subsystem: ABIT Computer Corp. KG7-Lite Mainboard
  Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
ParErr- Stepping+ SERR- FastB2B-
         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
  Latency: 0
  Capabilities: [c0] Power Management version 2
                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:07.1 IDE interface: VIA Technologies, Inc. 
VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06) 
(prog-if 8a [Master SecP PriP])
         Subsystem: VIA Technologies, Inc. 
VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
  Latency: 32
  Region 4: I/O ports at c400 [size=16]
  Capabilities: [c0] Power Management version 2
                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:07.2 USB Controller: VIA Technologies, Inc. USB (rev 1a) (prog-if 00 
[UHCI])
  Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
  Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
ParErr- Stepping- SERR- FastB2B-
         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
  Latency: 32, cache line size 08
  Interrupt: pin D routed to IRQ 9
  Region 4: I/O ports at c800 [size=32]
  Capabilities: [80] Power Management version 2
                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:07.3 USB Controller: VIA Technologies, Inc. USB (rev 1a) (prog-if 00 
[UHCI])
  Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
  Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
ParErr- Stepping- SERR- FastB2B-
         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
  Latency: 32, cache line size 08
  Interrupt: pin D routed to IRQ 9
  Region 4: I/O ports at cc00 [size=32]
  Capabilities: [80] Power Management version 2
                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:07.4 SMBus: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 
40)
  Subsystem: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
  Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- 
ParErr- Stepping- SERR- FastB2B-
         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
  Interrupt: pin ? routed to IRQ 11
  Capabilities: [68] Power Management version 2
                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:09.0 Multimedia video controller: Brooktree Corporation Bt878 Video 
Capture (rev 11)
         Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR+
  Latency: 32 (4000ns min, 10000ns max)
  Interrupt: pin A routed to IRQ 5
  Region 0: Memory at f7000000 (32-bit, prefetchable)
Capabilities:  [44] Vital Product Data
Capabilities:  [4c] Power Management version 2
                 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:09.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture 
(rev 11)
         Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR+
  Latency: 32 (1000ns min, 63750ns max)
  Interrupt: pin A routed to IRQ 5
  Region 0: Memory at f7001000 (32-bit, prefetchable)
Capabilities:  [44] Vital Product Data
Capabilities:  [4c] Power Management version 2
                 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 
08)
  Subsystem: Creative Labs SB Live! 5.1 Model SB0100
  Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- 
ParErr- Stepping- SERR- FastB2B-
         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
  Latency: 32 (500ns min, 5000ns max)
  Interrupt: pin A routed to IRQ 9
  Region 0: I/O ports at d000
  Capabilities: [dc] Power Management version 2
                 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:0b.1 Input device controller: Creative Labs SB Live! MIDI/Game Port 
(rev 08)
  Subsystem: Creative Labs Gameport Joystick
  Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- 
ParErr- Stepping- SERR- FastB2B-
         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
  Latency: 32
  Region 0: I/O ports at d400
  Capabilities: [dc] Power Management version 2
                 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:0d.0 Unknown mass storage controller: CMD Technology Inc Silicon Image 
SiI 3112 SATARaid Controller (rev 02)
         Subsystem: CMD Technology Inc Silicon Image SiI 3112 SATARaid 
Controller
         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
         Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR+
  Latency: 32, cache line size 08
  Interrupt: pin A routed to IRQ 11
  Region 0: I/O ports at d800
  Region 1: I/O ports at dc00 [size=4]
  Region 2: I/O ports at e000 [size=8]
  Region 3: I/O ports at e400 [size=4]
  Region 4: I/O ports at e800 [size=16]
  Region 5: Memory at f7002000 (32-bit, non-prefetchable) [size=512]
  Capabilities: [60] Power Management version 2
                 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
  Status: D0 PME-Enable- DSel=0 DScale=2 PME-

0000:00:0f.0 Ethernet controller: Realtek Semiconductor Co., Ltd. 
RTL-8139/8139C/8139C+ (rev 10)
  Subsystem: Realtek Semiconductor Co., Ltd. RT8139
  Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
ParErr- Stepping- SERR- FastB2B-
         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR+
  Latency: 32 (8000ns min, 16000ns max)
  Interrupt: pin A routed to IRQ 11
  Region 0: I/O ports at ec00
  Region 1: Memory at f7004000 (32-bit, non-prefetchable) [size=256]
  Capabilities: [50] Power Management version 2
                 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA 
PME(D0-,D1+,D2+,D3hot+,D3cold+)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:01:05.0 VGA compatible controller: nVidia Corporation NV15 [GeForce2 
GTS/Pro] (rev a4) (prog-if 00 [VGA])
         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
         Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
  Latency: 248 (1250ns min, 250ns max)
  Interrupt: pin A routed to IRQ 10
  Region 0: Memory at f4000000 (32-bit, non-prefetchable)
  Region 1: Memory at e8000000 (32-bit, prefetchable) [size=128M]
  Capabilities: [60] Power Management version 1
                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
         Status: D0 PME-Enable- DSel=0 DScale=0 PME-
         Capabilities: [44] AGP version 2.0
                 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 
64bit- FW+ AGP3- Rate=x1,x2,x4
                 Command: RQ=16 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW+ 
Rate=x4


My log (2.6.11 without acpi=off):
Mar  2 23:36:56 kangur usbcore: registered new driver usbfs
Mar  2 23:36:56 kangur usbcore: registered new driver hub
Mar  2 23:36:56 kangur ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
Mar  2 23:36:56 kangur PCI: setting IRQ 10 as level-triggered
Mar  2 23:36:56 kangur ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 10 (level, 
low) -> IRQ 10
Mar  2 23:36:56 kangur parport_pc: VIA 686A/8231 detected
Mar  2 23:36:56 kangur parport_pc: probing current configuration
Mar  2 23:36:56 kangur parport_pc: Current parallel port base: 0x378
Mar  2 23:36:56 kangur parport_pc: Strange, can't probe VIA parallel port: 
io=0x378, irq=7, dma=-1
Mar  2 23:36:56 kangur pnp: the driver 'parport_pc' has been registered
Mar  2 23:36:56 kangur pnp: match found with the PnP device '00:09' and the 
driver 'parport_pc'
Mar  2 23:36:56 kangur parport: PnPBIOS parport detected.
Mar  2 23:36:56 kangur parport0: PC-style at 0x378, irq 7 [PCSPP(,...)]
Mar  2 23:36:56 kangur USB Universal Host Controller Interface driver v2.2
Mar  2 23:36:56 kangur ACPI: PCI interrupt 0000:00:07.2[D] -> GSI 10 (level, 
low) -> IRQ 10
Mar  2 23:36:56 kangur uhci_hcd 0000:00:07.2: UHCI Host Controller
Mar  2 23:36:56 kangur uhci_hcd 0000:00:07.2: irq 10, io base 0xc800
Mar  2 23:36:56 kangur uhci_hcd 0000:00:07.2: new USB bus registered, assigned 
bus number 1
Mar  2 23:36:56 kangur hub 1-0:1.0: USB hub found
Mar  2 23:36:56 kangur hub 1-0:1.0: 2 ports detected
Mar  2 23:36:56 kangur ACPI: PCI interrupt 0000:00:07.3[D] -> GSI 10 (level, 
low) -> IRQ 10
Mar  2 23:36:56 kangur uhci_hcd 0000:00:07.3: UHCI Host Controller
Mar  2 23:36:56 kangur uhci_hcd 0000:00:07.3: irq 10, io base 0xcc00
Mar  2 23:36:56 kangur uhci_hcd 0000:00:07.3: new USB bus registered, assigned 
bus number 2
Mar  2 23:36:56 kangur hub 2-0:1.0: USB hub found
Mar  2 23:36:56 kangur hub 2-0:1.0: 2 ports detected
Mar  2 23:36:56 kangur usb 1-2: new full speed USB device using uhci_hcd and 
address 2
Mar  2 23:36:56 kangur Linux video capture interface: v1.00
Mar  2 23:36:56 kangur bttv: driver version 0.9.15 loaded
Mar  2 23:36:56 kangur bttv: using 32 buffers with 2080k (520 pages) each for 
capture
Mar  2 23:36:56 kangur bttv: Bt8xx card found (0).
Mar  2 23:36:56 kangur ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
Mar  2 23:36:56 kangur PCI: setting IRQ 5 as level-triggered
Mar  2 23:36:56 kangur ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 5 (level, 
low) -> IRQ 5
Mar  2 23:36:56 kangur bttv0: Bt878 (rev 17) at 0000:00:09.0, irq: 5, latency: 
32, mmio: 0xf7000000
Mar  2 23:36:56 kangur bttv0: using: Prolink Pixelview PV-BT878P+ (Rev.4C,8E) 
[card=70,insmod option]
Mar  2 23:36:56 kangur bttv0: gpio: en=00000000, out=00000000 in=00ffc0ff 
[init]
Mar  2 23:36:56 kangur bttv0: using tuner=25
Mar  2 23:36:56 kangur bttv0: i2c: checking for MSP34xx @ 0x80... not found
Mar  2 23:36:56 kangur bttv0: i2c: checking for TDA9875 @ 0xb0... not found
Mar  2 23:36:56 kangur bttv0: i2c: checking for TDA7432 @ 0x8a... not found
Mar  2 23:36:56 kangur tvaudio: TV audio decoder + audio/video mux driver
Mar  2 23:36:56 kangur tvaudio: known chips: 
tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6320,tea6420,tda8425,pic16c54 
(PV951),ta8874z
Mar  2 23:36:56 kangur bttv0: i2c: checking for TDA9887 @ 0x86... not found
Mar  2 23:36:56 kangur tuner 0-0061: chip found @ 0xc2 (bt878 #0 [sw])
Mar  2 23:36:56 kangur tuner 0-0061: type set to 25 (LG PAL_I+FM (TAPC-I001D))
Mar  2 23:36:56 kangur bttv0: registered device video0
Mar  2 23:36:56 kangur bttv0: registered device vbi0
Mar  2 23:36:56 kangur bttv0: registered device radio0
Mar  2 23:36:56 kangur bttv0: PLL: 28636363 => 35468950 .. ok
Mar  2 23:36:56 kangur bttv0: add subdevice "remote0"
Mar  2 23:36:56 kangur uhci_hcd 0000:00:07.2: Unlink after no-IRQ? Controller 
is probably using the wrong IRQ.
Mar  2 23:36:56 kangur usb 1-2: khubd timed out on ep0in
Mar  2 23:36:56 kangur gameport: pci0000:00:0b.1 speed 1242 kHz
Mar  2 23:36:56 kangur Real Time Clock Driver v1.12
Mar  2 23:36:56 kangur Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ 
sharing disabled
Mar  2 23:36:56 kangur ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Mar  2 23:36:56 kangur ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Mar  2 23:36:56 kangur pnp: the driver 'serial' has been registered
Mar  2 23:36:56 kangur pnp: match found with the PnP device '00:07' and the 
driver 'serial'
Mar  2 23:36:56 kangur ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Mar  2 23:36:56 kangur pnp: match found with the PnP device '00:08' and the 
driver 'serial'
Mar  2 23:36:56 kangur ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Mar  2 23:36:56 kangur usb 1-2: khubd timed out on ep0out
Mar  2 23:36:56 kangur eth0: link down
Mar  2 23:36:56 kangur eth0: link down
Mar  2 23:36:56 kangur usb 1-2: khubd timed out on ep0out
Mar  2 23:36:56 kangur usb 1-2: device not accepting address 2, error -110
Mar  2 23:36:56 kangur usb 1-2: new full speed USB device using uhci_hcd and 
address 3
Mar  2 23:36:56 kangur usb 1-2: khubd timed out on ep0in
Mar  2 23:36:56 kangur usb 1-2: khubd timed out on ep0out
Mar  2 23:36:56 kangur usb 1-2: khubd timed out on ep0out
Mar  2 23:36:56 kangur usb 1-2: device not accepting address 3, error -110


My log (2.6.11 with acpi=off):
Mar  3 01:45:48 kangur usbcore: registered new driver usbfs
Mar  3 01:45:48 kangur usbcore: registered new driver hub
Mar  3 01:45:48 kangur PCI: Found IRQ 9 for device 0000:00:0b.0
Mar  3 01:45:48 kangur PCI: Sharing IRQ 9 with 0000:00:07.2
Mar  3 01:45:48 kangur PCI: Sharing IRQ 9 with 0000:00:07.3
Mar  3 01:45:48 kangur parport_pc: VIA 686A/8231 detected
Mar  3 01:45:48 kangur parport_pc: probing current configuration
Mar  3 01:45:48 kangur parport_pc: Current parallel port base: 0x378
Mar  3 01:45:48 kangur parport_pc: Strange, can't probe VIA parallel port: 
io=0x378, irq=7, dma=-1
Mar  3 01:45:48 kangur pnp: the driver 'parport_pc' has been registered
Mar  3 01:45:48 kangur parport0: PC-style at 0x378 [PCSPP(,...)]
Mar  3 01:45:48 kangur USB Universal Host Controller Interface driver v2.2
Mar  3 01:45:48 kangur PCI: Found IRQ 9 for device 0000:00:07.2
Mar  3 01:45:48 kangur PCI: Sharing IRQ 9 with 0000:00:07.3
Mar  3 01:45:48 kangur PCI: Sharing IRQ 9 with 0000:00:0b.0
Mar  3 01:45:48 kangur uhci_hcd 0000:00:07.2: UHCI Host Controller
Mar  3 01:45:48 kangur uhci_hcd 0000:00:07.2: irq 9, io base 0xc800
Mar  3 01:45:48 kangur uhci_hcd 0000:00:07.2: new USB bus registered, assigned 
bus number 1
Mar  3 01:45:48 kangur hub 1-0:1.0: USB hub found
Mar  3 01:45:48 kangur hub 1-0:1.0: 2 ports detected
Mar  3 01:45:48 kangur PCI: Found IRQ 9 for device 0000:00:07.3
Mar  3 01:45:48 kangur PCI: Sharing IRQ 9 with 0000:00:07.2
Mar  3 01:45:48 kangur PCI: Sharing IRQ 9 with 0000:00:0b.0
Mar  3 01:45:48 kangur uhci_hcd 0000:00:07.3: UHCI Host Controller
Mar  3 01:45:48 kangur uhci_hcd 0000:00:07.3: irq 9, io base 0xcc00
Mar  3 01:45:48 kangur uhci_hcd 0000:00:07.3: new USB bus registered, assigned 
bus number 2
Mar  3 01:45:48 kangur hub 2-0:1.0: USB hub found
Mar  3 01:45:48 kangur hub 2-0:1.0: 2 ports detected
Mar  3 01:45:48 kangur usb 1-2: new full speed USB device using uhci_hcd and 
address 2


Could somebody produce fast patch for me?


Thanks in advance,

Grzegorz Kulewski


-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/


-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now.
http://ads.osdn.com/?ad_id=6595&alloc_id=14396&op=click

^ permalink raw reply	[flat|nested] 26+ messages in thread
* RE: Re: Fw: Anybody? 2.6.11 (stable and -rc) ACPI breaks USB
@ 2005-03-14  9:30 Li, Shaohua
  0 siblings, 0 replies; 26+ messages in thread
From: Li, Shaohua @ 2005-03-14  9:30 UTC (permalink / raw)
  To: Grzegorz Kulewski, Bjorn Helgaas; +Cc: Andrew Morton, ACPI List, lkml

Hi,
This issue is quite interesting. We removed all specific VIA quirk
recently and apply a generic VIA quirk. But in this case, the MCH 00:0.0
is from AMD, and the ISA bridge and built-in devices are from VIA, this
means VIA quirk is useless, since it takes action only when the MCH is
from VIA. We possibly should enable VIA quirk if a VIA ISA bridge is
found instead of a VIA MCH found, but Bjorn's method seems ok.
If you want to put the patch into kernel, please also change the '
pirq_enable_irq' case.

Thanks,
Shaohua

>-----Original Message-----
>From: acpi-devel-admin-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org [mailto:acpi-devel-
>admin-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org] On Behalf Of Grzegorz Kulewski
>Sent: Sunday, March 13, 2005 11:15 PM
>To: Bjorn Helgaas
>Cc: Andrew Morton; ACPI List; lkml
>Subject: Re: [ACPI] Re: Fw: Anybody? 2.6.11 (stable and -rc) ACPI
breaks
>USB
>
>On Fri, 11 Mar 2005, Bjorn Helgaas wrote:
>
>> Can you do an "lspci -vvn"?  I'm looking at quirk_via_irqpic() in
>> 2.6.9, which is what printed this:
>>
>>>>    PCI: Via IRQ fixup for 0000:00:07.2, from 9 to 10
>>>>    PCI: Via IRQ fixup for 0000:00:07.3, from 9 to 10
>>
>> but it looks like it should only run for PCI_DEVICE_ID_VIA_82C586_2,
>> PCI_DEVICE_ID_VIA_82C686_5, and PCI_DEVICE_ID_VIA_82C686_6.
>>
>> You have:
>>
>> 0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo
Super
>South] (rev 40)
>> 0000:00:07.1 IDE interface: VIA Technologies, Inc.
>VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06)
>> 0000:00:07.2 USB Controller: VIA Technologies, Inc. USB (rev 1a)
(prog-if
>00 [UHCI])
>> 0000:00:07.3 USB Controller: VIA Technologies, Inc. USB (rev 1a)
(prog-if
>00 [UHCI])
>>
>> and we apparently ran the quirk for 07.2 and 07.3.  I wouldn't
>> have thought those would have one of the above device IDs.  The
>> "lspci -vvn" should tell us for sure.
>>
>> 2.6.11 removed that quirk and runs quirk_via_bridge() for
>> all VIA devices, but only sets via_interrupt_line_quirk if
>> (pdev->devfn == 0), which you don't have.  So that's why
>> my patch didn't do anything.
>>
>>> Also two more questions:
>>>
>>> 1. What is VIA fixup? Is it some hardware bug? Or BIOS problem? Why
is
>it
>>> needed? On what hardware / software it is needed?
>>
>> I really don't know much about the VIA fixup.  I just noticed
>> that we seem to be doing it slightly differently in 2.6.11 than
>> we did in 2.6.9, and thought maybe it was related to your problem.
>> Here's a changeset that has a couple pointers:
>>
>>    http://linux.bkbits.net:8080/linux-
>2.5/cset%4041cb9d48DRV4TYe77gvstTawuZFYyQ
>>
>>> 2. Why this patch shrinked bzImage that much:
>>>
>>> -rw-r--r--  1 root root 1828186 mar 11 23:33 vmlinuz-2.6.11-cko1
>>> -rw-r--r--  1 root root 1828355 mar  2 20:48 vmlinuz-2.6.11-cko1.old
>>
>> I have no idea about this.  But it's only a couple hundred bytes.
>>
>> So here's another patch to try (revert the first one, then apply
this).
>>
>> ===== drivers/acpi/pci_irq.c 1.37 vs edited =====
>> --- 1.37/drivers/acpi/pci_irq.c	2005-03-01 09:57:29 -07:00
>> +++ edited/drivers/acpi/pci_irq.c	2005-03-11 15:13:49 -07:00
>> @@ -30,6 +30,7 @@
>> #include <linux/module.h>
>> #include <linux/init.h>
>> #include <linux/types.h>
>> +#include <linux/delay.h>
>> #include <linux/proc_fs.h>
>> #include <linux/spinlock.h>
>> #include <linux/pm.h>
>> @@ -438,10 +439,17 @@
>> 		}
>>  	}
>>
>> -	if (via_interrupt_line_quirk)
>> -		pci_write_config_byte(dev, PCI_INTERRUPT_LINE, irq &
15);
>> -
>> 	dev->irq = acpi_register_gsi(irq, edge_level, active_high_low);
>> +
>> +	if (dev->vendor == PCI_VENDOR_ID_VIA) {
>> +		u8 old_irq, new_irq = dev->irq & 0xf;
>> +
>> +		pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &old_irq);
>> +		printk(KERN_INFO PREFIX "Via IRQ fixup for %s, from %d "
>> +			"to %d\n", pci_name(dev), old_irq, new_irq);
>> +		udelay(15);
>> +		pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq);
>> +	}
>>
>> 	printk(KERN_INFO PREFIX "PCI interrupt %s[%c] -> GSI %u "
>> 		"(%s, %s) -> IRQ %d\n",
>>
>
>Ok, this patch works. Here is the log:
>
>Mar 13 17:16:17 kangur Linux version 2.6.11-cko1 (root@kangur) (gcc
>version 3.3.3 20040412 (Gentoo Linux 3.3.3-r6, ssp-3.3.2-2, pie-8.7.6))
#3
>Sun Mar 13 17:10:10 CET 2005
>Mar 13 17:16:17 kangur BIOS-provided physical RAM map:
>Mar 13 17:16:17 kangur BIOS-e820: 0000000000000000 - 000000000009fc00
>(usable)
>Mar 13 17:16:17 kangur BIOS-e820: 000000000009fc00 - 00000000000a0000
>(reserved)
>Mar 13 17:16:17 kangur BIOS-e820: 00000000000f0000 - 0000000000100000
>(reserved)
>Mar 13 17:16:17 kangur BIOS-e820: 0000000000100000 - 000000001fff0000
>(usable)
>Mar 13 17:16:17 kangur BIOS-e820: 000000001fff0000 - 000000001fff3000
>(ACPI NVS)
>Mar 13 17:16:17 kangur BIOS-e820: 000000001fff3000 - 0000000020000000
>(ACPI data)
>Mar 13 17:16:17 kangur BIOS-e820: 00000000ffff0000 - 0000000100000000
>(reserved)
>Mar 13 17:16:17 kangur 511MB LOWMEM available.
>Mar 13 17:16:17 kangur On node 0 totalpages: 131056
>Mar 13 17:16:17 kangur DMA zone: 4096 pages, LIFO batch:1
>Mar 13 17:16:17 kangur Normal zone: 126960 pages, LIFO batch:16
>Mar 13 17:16:17 kangur HighMem zone: 0 pages, LIFO batch:1
>Mar 13 17:16:17 kangur DMI 2.2 present.
>Mar 13 17:16:17 kangur ACPI: RSDP (v000 761686
>) @ 0x000f6a70
>Mar 13 17:16:17 kangur ACPI: RSDT (v001 761686 AWRDACPI 0x42302e31 AWRD
>0x00000000) @ 0x1fff3000
>Mar 13 17:16:17 kangur ACPI: FADT (v001 761686 AWRDACPI 0x42302e31 AWRD
>0x00000000) @ 0x1fff3040
>Mar 13 17:16:17 kangur ACPI: DSDT (v001 761686 AWRDACPI 0x00001000 MSFT
>0x0100000c) @ 0x00000000
>Mar 13 17:16:17 kangur ACPI: PM-Timer IO Port: 0x4008
>Mar 13 17:16:17 kangur Allocating PCI resources starting at 20000000
(gap:
>20000000:dfff0000)
>Mar 13 17:16:17 kangur Built 1 zonelists
>Mar 13 17:16:17 kangur Kernel command line: ro root=/dev/hdb4
>Mar 13 17:16:17 kangur Local APIC disabled by BIOS -- you can enable it
>with "lapic"
>Mar 13 17:16:17 kangur mapped APIC to ffffd000 (01402000)
>Mar 13 17:16:17 kangur Initializing CPU#0
>Mar 13 17:16:17 kangur CPU 0 irqstacks, hard=b0477000 soft=b0476000
>Mar 13 17:16:17 kangur PID hash table entries: 2048 (order: 11, 32768
>bytes)
>Mar 13 17:16:17 kangur Detected 1203.036 MHz processor.
>Mar 13 17:16:17 kangur Using pmtmr for high-res timesource
>Mar 13 17:16:17 kangur Console: colour VGA+ 80x25
>Mar 13 17:16:17 kangur Dentry cache hash table entries: 131072 (order:
7,
>524288 bytes)
>Mar 13 17:16:17 kangur Inode-cache hash table entries: 65536 (order: 6,
>262144 bytes)
>Mar 13 17:16:17 kangur Memory: 514940k/524224k available (2543k kernel
>code, 8732k reserved, 819k data, 156k init, 0k highmem)
>Mar 13 17:16:17 kangur Checking if this processor honours the WP bit
even
>in supervisor mode... Ok.
>Mar 13 17:16:17 kangur Calibrating delay loop... 2375.68 BogoMIPS
>(lpj=1187840)
>Mar 13 17:16:17 kangur Security Framework v1.0.0 initialized
>Mar 13 17:16:17 kangur Capability LSM initialized
>Mar 13 17:16:17 kangur Mount-cache hash table entries: 512 (order: 0,
4096
>bytes)
>Mar 13 17:16:17 kangur CPU: After generic identify, caps: 0383f9ff
>c1cbf9ff 00000000 00000000 00000000 00000000 00000000Mar 13 17:16:17
>kangur CPU: After vendor identify, caps: 0383f9ff c1cbf9ff 00000000
>00000000 00000000 00000000 00000000
>Mar 13 17:16:17 kangur CPU: CLK_CTL MSR was 60071263. Reprogramming to
>20071263
>Mar 13 17:16:17 kangur CPU: L1 I Cache: 64K (64 bytes/line), D cache
64K
>(64 bytes/line)
>Mar 13 17:16:17 kangur CPU: L2 Cache: 512K (64 bytes/line)
>Mar 13 17:16:17 kangur CPU: After all inits, caps: 0383f9ff c1cbf9ff
>00000000 00000020 00000000 00000000 00000000
>Mar 13 17:16:17 kangur Intel machine check architecture supported.
>Mar 13 17:16:17 kangur Intel machine check reporting enabled on CPU#0.
>Mar 13 17:16:17 kangur CPU: AMD Unknown CPU Type stepping 00
>Mar 13 17:16:17 kangur Enabling fast FPU save and restore... done.
>Mar 13 17:16:17 kangur Enabling unmasked SIMD FPU exception support...
>done.
>Mar 13 17:16:17 kangur Checking 'hlt' instruction... OK.
>Mar 13 17:16:17 kangur ACPI: setting ELCR to 0800 (from 0e20)
>Mar 13 17:16:17 kangur NET: Registered protocol family 16
>Mar 13 17:16:17 kangur PCI: PCI BIOS revision 2.10 entry at 0xfb690,
last
>bus=1
>Mar 13 17:16:17 kangur PCI: Using configuration type 1
>Mar 13 17:16:17 kangur mtrr: v2.0 (20020519)
>Mar 13 17:16:17 kangur ACPI: Subsystem revision 20050211
>Mar 13 17:16:17 kangur ACPI: Interpreter enabled
>Mar 13 17:16:17 kangur ACPI: Using PIC for interrupt routing
>Mar 13 17:16:17 kangur ACPI: PCI Root Bridge [PCI0] (00:00)
>Mar 13 17:16:17 kangur PCI: Probing PCI hardware (bus 00)
>Mar 13 17:16:17 kangur ACPI: PCI Interrupt Routing Table
[\_SB_.PCI0._PRT]
>Mar 13 17:16:17 kangur ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6
7
>*10 11 12 14 15)
>Mar 13 17:16:17 kangur ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6
7
>10 *11 12 14 15)
>Mar 13 17:16:17 kangur ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 *5 6
7
>10 11 12 14 15)
>Mar 13 17:16:17 kangur ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6
7
>10 11 12 14 15) *9
>Mar 13 17:16:17 kangur Linux Plug and Play Support v0.97 (c) Adam Belay
>Mar 13 17:16:17 kangur pnp: PnP ACPI init
>Mar 13 17:16:17 kangur pnp: PnP ACPI: found 12 devices
>Mar 13 17:16:17 kangur SCSI subsystem initialized
>Mar 13 17:16:17 kangur PCI: Using ACPI for IRQ routing
>Mar 13 17:16:17 kangur ** PCI interrupts are no longer routed
>automatically.  If this
>Mar 13 17:16:17 kangur ** causes a device to stop working, it is
probably
>because the
>Mar 13 17:16:17 kangur ** driver failed to call pci_enable_device().
As a
>temporary
>Mar 13 17:16:17 kangur ** workaround, the "pci=routeirq" argument
restores
>the old
>Mar 13 17:16:17 kangur ** behavior.  If this argument makes the device
>work again,
>Mar 13 17:16:17 kangur ** please email the output of "lspci" to
>bjorn.helgaas-VXdhtT5mjnY@public.gmane.org
>Mar 13 17:16:17 kangur ** so I can fix the driver.
>Mar 13 17:16:17 kangur pnp: the driver 'system' has been registered
>Mar 13 17:16:17 kangur pnp: match found with the PnP device '00:00' and
>the driver 'system'
>Mar 13 17:16:17 kangur pnp: match found with the PnP device '00:01' and
>the driver 'system'
>Mar 13 17:16:17 kangur Total HugeTLB memory allocated, 0
>Mar 13 17:16:17 kangur VFS: Disk quotas dquot_6.5.1
>Mar 13 17:16:17 kangur Dquot-cache hash table entries: 1024 (order 0,
4096
>bytes)
>Mar 13 17:16:17 kangur SGI XFS with ACLs, security attributes,
realtime,
>no debug enabled
>Mar 13 17:16:17 kangur SGI XFS Quota Management subsystem
>Mar 13 17:16:17 kangur Initializing Cryptographic API
>Mar 13 17:16:17 kangur inotify device minor=63
>Mar 13 17:16:17 kangur ACPI: PS/2 Keyboard Controller [PS2K] at I/O
0x60,
>0x64, irq 1
>Mar 13 17:16:17 kangur ACPI: PS/2 Mouse Controller [PS2M] at irq 12
>Mar 13 17:16:17 kangur serio: i8042 AUX port at 0x60,0x64 irq 12
>Mar 13 17:16:17 kangur serio: i8042 KBD port at 0x60,0x64 irq 1
>Mar 13 17:16:17 kangur io scheduler noop registered
>Mar 13 17:16:17 kangur io scheduler anticipatory registered
>Mar 13 17:16:17 kangur io scheduler deadline registered
>Mar 13 17:16:17 kangur io scheduler cfq registered
>Mar 13 17:16:17 kangur 8139too Fast Ethernet driver 0.9.27
>Mar 13 17:16:17 kangur ACPI: PCI Interrupt Link [LNKB] enabled at IRQ
11
>Mar 13 17:16:17 kangur PCI: setting IRQ 11 as level-triggered
>Mar 13 17:16:17 kangur ACPI: PCI interrupt 0000:00:0f.0[A] -> GSI 11
>(level, low) -> IRQ 11
>Mar 13 17:16:17 kangur eth0: RealTek RTL8139 at 0xec00,
00:06:4f:00:73:8b,
>IRQ 11
>Mar 13 17:16:17 kangur eth0:  Identified 8139 chip type 'RTL-8139C'
>Mar 13 17:16:17 kangur Uniform Multi-Platform E-IDE driver Revision:
>7.00alpha2
>Mar 13 17:16:17 kangur ide: Assuming 33MHz system bus speed for PIO
modes;
>override with idebus=xx
>Mar 13 17:16:17 kangur VP_IDE: IDE controller at PCI slot 0000:00:07.1
>Mar 13 17:16:17 kangur VP_IDE: chipset revision 6
>Mar 13 17:16:17 kangur VP_IDE: not 100% native mode: will probe irqs
later
>Mar 13 17:16:17 kangur VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100
>controller on pci0000:00:07.1
>Mar 13 17:16:17 kangur ide0: BM-DMA at 0xc400-0xc407, BIOS settings:
>hda:pio, hdb:DMA
>Mar 13 17:16:17 kangur ide1: BM-DMA at 0xc408-0xc40f, BIOS settings:
>hdc:pio, hdd:DMA
>Mar 13 17:16:17 kangur Probing IDE interface ide0...
>Mar 13 17:16:17 kangur hdb: SAMSUNG SV3063H, ATA DISK drive
>Mar 13 17:16:17 kangur ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
>Mar 13 17:16:17 kangur Probing IDE interface ide1...
>Mar 13 17:16:17 kangur hdd: HL-DT-ST DVDRAM GSA-4082B, ATAPI CD/DVD-ROM
>drive
>Mar 13 17:16:17 kangur ide1 at 0x170-0x177,0x376 on irq 15
>Mar 13 17:16:17 kangur pnp: the driver 'ide' has been registered
>Mar 13 17:16:17 kangur hdb: max request size: 128KiB
>Mar 13 17:16:17 kangur hdb: 59797584 sectors (30616 MB) w/426KiB Cache,
>CHS=59323/16/63, UDMA(100)
>Mar 13 17:16:17 kangur hdb: cache flushes not supported
>Mar 13 17:16:17 kangur hdb: hdb1 hdb2 hdb3 hdb4
>Mar 13 17:16:17 kangur libata version 1.10 loaded.
>Mar 13 17:16:17 kangur sata_sil version 0.8
>Mar 13 17:16:17 kangur ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 11
>(level, low) -> IRQ 11
>Mar 13 17:16:17 kangur ata1: SATA max UDMA/100 cmd 0xD0802080 ctl
>0xD080208A bmdma 0xD0802000 irq 11
>Mar 13 17:16:17 kangur ata2: SATA max UDMA/100 cmd 0xD08020C0 ctl
>0xD08020CA bmdma 0xD0802008 irq 11
>Mar 13 17:16:17 kangur ata1: dev 0 cfg 49:2f00 82:346b 83:7f61 84:4003
>85:3469 86:3c41 87:4003 88:207f
>Mar 13 17:16:17 kangur ata1: dev 0 ATA, max UDMA/133, 312581808
sectors:
>lba48
>Mar 13 17:16:17 kangur ata1: dev 0 configured for UDMA/100
>Mar 13 17:16:17 kangur scsi0 : sata_sil
>Mar 13 17:16:17 kangur ata2: no device found (phy stat 00000000)
>Mar 13 17:16:17 kangur scsi1 : sata_sil
>Mar 13 17:16:17 kangur Vendor: ATA       Model: WDC WD1600JD-00H  Rev:
>08.0
>Mar 13 17:16:17 kangur Type:   Direct-Access                      ANSI
>SCSI revision: 05
>Mar 13 17:16:17 kangur SCSI device sda: 312581808 512-byte hdwr sectors
>(160042 MB)
>Mar 13 17:16:17 kangur SCSI device sda: drive cache: write back
>Mar 13 17:16:17 kangur SCSI device sda: 312581808 512-byte hdwr sectors
>(160042 MB)
>Mar 13 17:16:17 kangur SCSI device sda: drive cache: write back
>Mar 13 17:16:17 kangur sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8
sda9
>sda10 sda11 sda12 sda13 sda14 sda15 >
>Mar 13 17:16:17 kangur Attached scsi disk sda at scsi0, channel 0, id
0,
>lun 0
>Mar 13 17:16:17 kangur mice: PS/2 mouse device common for all mice
>Mar 13 17:16:17 kangur input: AT Translated Set 2 keyboard on
>isa0060/serio0
>Mar 13 17:16:17 kangur NET: Registered protocol family 2
>Mar 13 17:16:17 kangur IP: routing cache hash table of 4096 buckets,
>32Kbytes
>Mar 13 17:16:17 kangur TCP established hash table entries: 32768
(order:
>6, 262144 bytes)
>Mar 13 17:16:17 kangur TCP bind hash table entries: 32768 (order: 5,
>131072 bytes)
>Mar 13 17:16:17 kangur TCP: Hash tables configured (established 32768
bind
>32768)
>Mar 13 17:16:17 kangur ip_conntrack version 2.1 (4095 buckets, 32760
max)
>- 216 bytes per conntrack
>Mar 13 17:16:17 kangur ip_tables: (C) 2000-2002 Netfilter core team
>Mar 13 17:16:17 kangur ipt_recent v0.3.1: Stephen Frost
><sfrost-vhD3WmCyG/PR7s880joybQ@public.gmane.org>.  http://snowman.net/projects/ipt_recent/
>Mar 13 17:16:17 kangur arp_tables: (C) 2002 David S. Miller
>Mar 13 17:16:17 kangur NET: Registered protocol family 17
>Mar 13 17:16:17 kangur ACPI wakeup devices:
>Mar 13 17:16:17 kangur SLPB PCI0 USB0 USB1
>Mar 13 17:16:17 kangur ACPI: (supports S0 S1 S4 S5)
>Mar 13 17:16:17 kangur kjournald starting.  Commit interval 5 seconds
>Mar 13 17:16:17 kangur EXT3-fs: mounted filesystem with ordered data
mode.
>Mar 13 17:16:17 kangur VFS: Mounted root (ext3 filesystem) readonly.
>Mar 13 17:16:17 kangur Freeing unused kernel memory: 156k freed
>Mar 13 17:16:17 kangur NET: Registered protocol family 1
>Mar 13 17:16:17 kangur EXT3 FS on hdb4, internal journal
>Mar 13 17:16:17 kangur NET: Registered protocol family 8
>Mar 13 17:16:17 kangur NET: Registered protocol family 20
>Mar 13 17:16:17 kangur CSLIP: code copyright 1989 Regents of the
>University of California
>Mar 13 17:16:17 kangur PPP generic driver version 2.4.2
>Mar 13 17:16:17 kangur input: PS/2 Generic Mouse on isa0060/serio1
>Mar 13 17:16:17 kangur input: PC Speaker
>Mar 13 17:16:17 kangur loop: loaded (max 8 devices)
>Mar 13 17:16:17 kangur Non-volatile memory driver v1.2
>Mar 13 17:16:17 kangur BIOS EDD facility v0.16 2004-Jun-25, 2 devices
>found
>Mar 13 17:16:17 kangur vesafb: NVidia Corporation, NV15 Reference
Board,
>Chip Rev A0 (OEM: NVidia)
>Mar 13 17:16:17 kangur vesafb: VBE version: 3.0
>Mar 13 17:16:17 kangur vesafb: protected mode interface info at
c000:0f03
>Mar 13 17:16:17 kangur vesafb: pmi: set display start = b00c0f3c, set
>palette = b00c0fb2
>Mar 13 17:16:17 kangur vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5
>3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
>Mar 13 17:16:17 kangur vesafb: hardware supports DCC2 transfers
>Mar 13 17:16:17 kangur vesafb: monitor limits: vf = 85 Hz, hf = 64 kHz,
>clk = 108 MHz
>Mar 13 17:16:17 kangur vesafb: scrolling: redraw
>Mar 13 17:16:17 kangur vesafb: framebuffer at 0xe8000000, mapped to
>0xd0900000, using 6144k, total 65536k
>Mar 13 17:16:17 kangur fb0: VESA VGA frame buffer device
>Mar 13 17:16:17 kangur Console: switching to colour frame buffer device
>128x48
>Mar 13 17:16:17 kangur device-mapper: 4.4.0-ioctl (2005-01-12)
>initialised: dm-devel-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org
>Mar 13 17:16:17 kangur NTFS driver 2.1.22 [Flags: R/O MODULE].
>Mar 13 17:16:17 kangur NTFS volume version 3.1.
>Mar 13 17:16:17 kangur NTFS volume version 3.1.
>Mar 13 17:16:17 kangur usbcore: registered new driver usbfs
>Mar 13 17:16:17 kangur usbcore: registered new driver hub
>Mar 13 17:16:17 kangur ACPI: PCI Interrupt Link [LNKD] enabled at IRQ
10
>Mar 13 17:16:17 kangur PCI: setting IRQ 10 as level-triggered
>Mar 13 17:16:17 kangur ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 10
>(level, low) -> IRQ 10
>Mar 13 17:16:17 kangur parport_pc: VIA 686A/8231 detected
>Mar 13 17:16:17 kangur parport_pc: probing current configuration
>Mar 13 17:16:17 kangur parport_pc: Current parallel port base: 0x378
>Mar 13 17:16:17 kangur parport_pc: Strange, can't probe VIA parallel
port:
>io=0x378, irq=7, dma=-1
>Mar 13 17:16:17 kangur pnp: the driver 'parport_pc' has been registered
>Mar 13 17:16:17 kangur pnp: match found with the PnP device '00:09' and
>the driver 'parport_pc'
>Mar 13 17:16:17 kangur parport: PnPBIOS parport detected.
>Mar 13 17:16:17 kangur parport0: PC-style at 0x378, irq 7 [PCSPP(,...)]
>Mar 13 17:16:17 kangur USB Universal Host Controller Interface driver
v2.2
>Mar 13 17:16:17 kangur ACPI: Via IRQ fixup for 0000:00:07.2, from 9 to
10
>Mar 13 17:16:17 kangur ACPI: PCI interrupt 0000:00:07.2[D] -> GSI 10
>(level, low) -> IRQ 10
>Mar 13 17:16:17 kangur uhci_hcd 0000:00:07.2: UHCI Host Controller
>Mar 13 17:16:17 kangur uhci_hcd 0000:00:07.2: irq 10, io base 0xc800
>Mar 13 17:16:17 kangur uhci_hcd 0000:00:07.2: new USB bus registered,
>assigned bus number 1
>Mar 13 17:16:17 kangur hub 1-0:1.0: USB hub found
>Mar 13 17:16:17 kangur hub 1-0:1.0: 2 ports detected
>Mar 13 17:16:17 kangur ACPI: Via IRQ fixup for 0000:00:07.3, from 9 to
10
>Mar 13 17:16:17 kangur ACPI: PCI interrupt 0000:00:07.3[D] -> GSI 10
>(level, low) -> IRQ 10
>Mar 13 17:16:17 kangur uhci_hcd 0000:00:07.3: UHCI Host Controller
>Mar 13 17:16:17 kangur uhci_hcd 0000:00:07.3: irq 10, io base 0xcc00
>Mar 13 17:16:17 kangur uhci_hcd 0000:00:07.3: new USB bus registered,
>assigned bus number 2
>Mar 13 17:16:17 kangur hub 2-0:1.0: USB hub found
>Mar 13 17:16:17 kangur hub 2-0:1.0: 2 ports detected
>Mar 13 17:16:17 kangur usb 1-2: new full speed USB device using
uhci_hcd
>and address 2
>Mar 13 17:16:17 kangur Linux video capture interface: v1.00
>Mar 13 17:16:17 kangur bttv: driver version 0.9.15 loaded
>Mar 13 17:16:17 kangur bttv: using 32 buffers with 2080k (520 pages)
each
>for capture
>Mar 13 17:16:17 kangur bttv: Bt8xx card found (0).
>Mar 13 17:16:17 kangur ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
>Mar 13 17:16:17 kangur PCI: setting IRQ 5 as level-triggered
>Mar 13 17:16:17 kangur ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 5
>(level, low) -> IRQ 5
>Mar 13 17:16:17 kangur bttv0: Bt878 (rev 17) at 0000:00:09.0, irq: 5,
>latency: 32, mmio: 0xf7000000
>Mar 13 17:16:17 kangur bttv0: using: Prolink Pixelview PV-BT878P+
>(Rev.4C,8E) [card=70,insmod option]
>Mar 13 17:16:17 kangur bttv0: gpio: en=00000000, out=00000000
in=00ffc0ff
>[init]
>Mar 13 17:16:17 kangur bttv0: using tuner=25
>Mar 13 17:16:17 kangur bttv0: i2c: checking for MSP34xx @ 0x80... not
>found
>Mar 13 17:16:17 kangur bttv0: i2c: checking for TDA9875 @ 0xb0... not
>found
>Mar 13 17:16:17 kangur bttv0: i2c: checking for TDA7432 @ 0x8a... not
>found
>Mar 13 17:16:17 kangur tvaudio: TV audio decoder + audio/video mux
driver
>Mar 13 17:16:17 kangur tvaudio: known chips:
>tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6320,tea6420,tda
8425
>,pic16c54
>(PV951),ta8874z
>Mar 13 17:16:17 kangur bttv0: i2c: checking for TDA9887 @ 0x86... not
>found
>Mar 13 17:16:17 kangur tuner 0-0061: chip found @ 0xc2 (bt878 #0 [sw])
>Mar 13 17:16:17 kangur tuner 0-0061: type set to 25 (LG PAL_I+FM
>(TAPC-I001D))
>Mar 13 17:16:17 kangur bttv0: registered device video0
>Mar 13 17:16:17 kangur bttv0: registered device vbi0
>Mar 13 17:16:17 kangur bttv0: registered device radio0
>Mar 13 17:16:17 kangur bttv0: PLL: 28636363 => 35468950 .. ok
>Mar 13 17:16:17 kangur bttv0: add subdevice "remote0"
>Mar 13 17:16:17 kangur usb 1-2: modprobe timed out on ep0in
>Mar 13 17:16:17 kangur usbcore: registered new driver speedtch
>Mar 13 17:16:17 kangur usb 1-2: found stage 1 firmware speedtch-1.bin
>Mar 13 17:16:17 kangur gameport: pci0000:00:0b.1 speed 1242 kHz
>Mar 13 17:16:17 kangur nvidia: module license 'NVIDIA' taints kernel.
>Mar 13 17:16:17 kangur ACPI: PCI Interrupt Link [LNKA] enabled at IRQ
10
>Mar 13 17:16:17 kangur ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 10
>(level, low) -> IRQ 10
>Mar 13 17:16:17 kangur NVRM: loading NVIDIA Linux x86 NVIDIA Kernel
Module
>1.0-6629  Wed Nov  3 13:12:51 PST 2004
>Mar 13 17:16:17 kangur usb 1-2: found stage 2 firmware speedtch-2.bin
>Mar 13 17:16:17 kangur Real Time Clock Driver v1.12
>Mar 13 17:16:17 kangur Floppy drive(s): fd0 is 1.44M
>Mar 13 17:16:17 kangur FDC 0 is a post-1991 82077
>Mar 13 17:16:17 kangur Serial: 8250/16550 driver $Revision: 1.90 $ 8
>ports, IRQ sharing disabled
>Mar 13 17:16:17 kangur ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
>Mar 13 17:16:17 kangur ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
>Mar 13 17:16:17 kangur pnp: the driver 'serial' has been registered
>Mar 13 17:16:17 kangur pnp: match found with the PnP device '00:07' and
>the driver 'serial'
>Mar 13 17:16:17 kangur ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
>Mar 13 17:16:17 kangur pnp: match found with the PnP device '00:08' and
>the driver 'serial'
>Mar 13 17:16:17 kangur ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
>Mar 13 17:16:17 kangur ADSL line is synchronising
>Mar 13 17:16:19 kangur eth0: link down
>Mar 13 17:16:19 kangur eth0: link down
>Mar 13 17:16:20 kangur NET: Registered protocol family 10
>Mar 13 17:16:20 kangur Disabled Privacy Extensions on device
b03e7aa0(lo)
>Mar 13 17:16:20 kangur IPv6 over IPv4 tunneling driver
>
>
>It generated the following warning:
>   CC      drivers/acpi/pci_irq.o
>drivers/acpi/pci_irq.c: In function `acpi_pci_irq_enable':
>drivers/acpi/pci_irq.c:392: warning: unused variable
>`via_interrupt_line_quirk'
>
>(I think this warning is new).
>
>The lspci:
>
># lspci -vvn
>0000:00:00.0 Class 0600: 1022:700e (rev 13)
>         Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>ParErr- Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort-
><TAbort- <MAbort+ >SERR- <PERR-
>         Latency: 32
>         Region 0: Memory at f0000000 (32-bit, prefetchable)
>         Region 1: Memory at f7003000 (32-bit, prefetchable) [size=4K]
>         Region 2: I/O ports at c000 [disabled] [size=4]
>         Capabilities: [a0] AGP version 2.0
>                 Status: RQ=16 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
>HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
>                 Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit-
FW+
>Rate=x4
>
>0000:00:01.0 Class 0604: 1022:700f
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>ParErr- Stepping- SERR+ FastB2B-
>         Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort-
><TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32
>         Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
>         Memory behind bridge: f4000000-f5ffffff
>         Prefetchable memory behind bridge: e8000000-efffffff
>         BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
>
>0000:00:07.0 Class 0601: 1106:0686 (rev 40)
>         Subsystem: 147b:a702
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>ParErr- Stepping+ SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort-
><TAbort- <MAbort- >SERR- <PERR-
>         Latency: 0
>         Capabilities: [c0] Power Management version 2
>                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
>PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>0000:00:07.1 Class 0101: 1106:0571 (rev 06) (prog-if 8a [Master SecP
>PriP])
>         Subsystem: 1106:0571
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>ParErr- Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort-
><TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32
>         Region 4: I/O ports at c400 [size=16]
>         Capabilities: [c0] Power Management version 2
>                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
>PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>0000:00:07.2 Class 0c03: 1106:3038 (rev 1a)
>         Subsystem: 0925:1234
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>ParErr- Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort-
><TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32, cache line size 08
>         Interrupt: pin D routed to IRQ 10
>         Region 4: I/O ports at c800 [size=32]
>         Capabilities: [80] Power Management version 2
>                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
>PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>0000:00:07.3 Class 0c03: 1106:3038 (rev 1a)
>         Subsystem: 0925:1234
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>ParErr- Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort-
><TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32, cache line size 08
>         Interrupt: pin D routed to IRQ 10
>         Region 4: I/O ports at cc00 [size=32]
>         Capabilities: [80] Power Management version 2
>                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
>PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>0000:00:07.4 Class 0c05: 1106:3057 (rev 40)
>         Subsystem: 1106:3057
>         Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
>ParErr- Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort-
><TAbort- <MAbort- >SERR- <PERR-
>         Interrupt: pin ? routed to IRQ 11
>         Capabilities: [68] Power Management version 2
>                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
>PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>0000:00:09.0 Class 0400: 109e:036e (rev 11)
>         Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>ParErr- Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort-
><TAbort- <MAbort- >SERR- <PERR+
>         Latency: 32 (4000ns min, 10000ns max)
>         Interrupt: pin A routed to IRQ 5
>         Region 0: Memory at f7000000 (32-bit, prefetchable)
>         Capabilities: [44] Vital Product Data
>         Capabilities: [4c] Power Management version 2
>                 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
>PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>0000:00:09.1 Class 0480: 109e:0878 (rev 11)
>         Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>ParErr- Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort-
><TAbort- <MAbort- >SERR- <PERR+
>         Latency: 32 (1000ns min, 63750ns max)
>         Interrupt: pin A routed to IRQ 5
>         Region 0: Memory at f7001000 (32-bit, prefetchable)
>         Capabilities: [44] Vital Product Data
>         Capabilities: [4c] Power Management version 2
>                 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
>PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>0000:00:0b.0 Class 0401: 1102:0002 (rev 08)
>         Subsystem: 1102:8064
>         Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
>ParErr- Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort-
><TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32 (500ns min, 5000ns max)
>         Interrupt: pin A routed to IRQ 10
>         Region 0: I/O ports at d000
>         Capabilities: [dc] Power Management version 2
>                 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
>PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>0000:00:0b.1 Class 0980: 1102:7002 (rev 08)
>         Subsystem: 1102:0020
>         Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
>ParErr- Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort-
><TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32
>         Region 0: I/O ports at d400
>         Capabilities: [dc] Power Management version 2
>                 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
>PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>0000:00:0d.0 Class 0180: 1095:3112 (rev 02)
>         Subsystem: 1095:3112
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>ParErr- Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort-
><TAbort- <MAbort- >SERR- <PERR+
>         Latency: 32, cache line size 08
>         Interrupt: pin A routed to IRQ 11
>         Region 0: I/O ports at d800
>         Region 1: I/O ports at dc00 [size=4]
>         Region 2: I/O ports at e000 [size=8]
>         Region 3: I/O ports at e400 [size=4]
>         Region 4: I/O ports at e800 [size=16]
>         Region 5: Memory at f7002000 (32-bit, non-prefetchable)
[size=512]
>         Capabilities: [60] Power Management version 2
>                 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
>PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=2 PME-
>
>0000:00:0f.0 Class 0200: 10ec:8139 (rev 10)
>         Subsystem: 10ec:8139
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>ParErr- Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort-
><TAbort- <MAbort- >SERR- <PERR+
>         Latency: 32 (8000ns min, 16000ns max)
>         Interrupt: pin A routed to IRQ 11
>         Region 0: I/O ports at ec00
>         Region 1: Memory at f7004000 (32-bit, non-prefetchable)
[size=256]
>         Capabilities: [50] Power Management version 2
>                 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
>PME(D0-,D1+,D2+,D3hot+,D3cold+)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>0000:01:05.0 Class 0300: 10de:0150 (rev a4)
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>ParErr- Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort-
><TAbort- <MAbort- >SERR- <PERR-
>         Latency: 248 (1250ns min, 250ns max)
>         Interrupt: pin A routed to IRQ 10
>         Region 0: Memory at f4000000 (32-bit, non-prefetchable)
>         Region 1: Memory at e8000000 (32-bit, prefetchable)
[size=128M]
>         Capabilities: [60] Power Management version 1
>                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
>PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>         Capabilities: [44] AGP version 2.0
>                 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
>HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
>                 Command: RQ=16 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit-
FW+
>Rate=x4
>
>
>To me everything works (at least now). Can this patch be pushed into
>2.6.12 and/or 2.6.11.4 fast?
>



-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now.
http://ads.osdn.com/?ad_ide95&alloc_id\x14396&op=click

^ permalink raw reply	[flat|nested] 26+ messages in thread
end of thread, other threads:[~2005-03-25 19:07 UTC | newest]

Thread overview: 26+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2005-03-05  7:46 Fw: Anybody? 2.6.11 (stable and -rc) ACPI breaks USB Andrew Morton
     [not found] ` <20050304234622.63e8a335.akpm-3NddpPZAyC0@public.gmane.org>
2005-03-05  8:10   ` Patrick Ale
2005-03-10 23:08   ` Grzegorz Kulewski
     [not found]     ` <Pine.LNX.4.62.0503110006260.30687-xO7mqm7LmoOZ0THcR2OzsA@public.gmane.org>
2005-03-11 16:48       ` Bjorn Helgaas
2005-03-11 19:36         ` Grzegorz Kulewski
     [not found]           ` <Pine.LNX.4.62.0503112009070.22293-xO7mqm7LmoOZ0THcR2OzsA@public.gmane.org>
2005-03-11 20:56             ` Bjorn Helgaas
2005-03-11 21:47               ` Grzegorz Kulewski
     [not found]                 ` <Pine.LNX.4.62.0503112239580.25254-xO7mqm7LmoOZ0THcR2OzsA@public.gmane.org>
2005-03-11 22:29                   ` Bjorn Helgaas
2005-03-12  0:13                     ` Grzegorz Kulewski
2005-03-13 15:14                     ` Grzegorz Kulewski
     [not found]                       ` <Pine.LNX.4.62.0503131607330.23588-xO7mqm7LmoOZ0THcR2OzsA@public.gmane.org>
2005-03-15 19:35                         ` Bjorn Helgaas
2005-03-15 23:02                           ` Zwane Mwaikambo
     [not found]                             ` <Pine.LNX.4.61.0503151543420.23036-SOP5cCwKKQRMCHjbocvOOJqQE7yCjDx5@public.gmane.org>
2005-03-16 16:10                               ` Bjorn Helgaas
2005-03-17  1:33                                 ` Li Shaohua
2005-03-17 18:08                                   ` [ACPI] " Bjorn Helgaas
2005-03-18  1:09                                     ` Li Shaohua
     [not found]                                       ` <1111108150.22239.6.camel-U5EdaLXB8smDugQYiPIPGdh3ngVCH38I@public.gmane.org>
2005-03-18 18:07                                         ` Bjorn Helgaas
2005-03-21 16:33                                           ` [ACPI] " Bjorn Helgaas
2005-03-21 23:33                                             ` Grzegorz Kulewski
2005-03-22 20:57                                               ` [ACPI] " Bjorn Helgaas
     [not found]                                                 ` <41062.15.99.19.46.1111525073.squirrel-hO9VIT4gnBFxnVILBQAtiA@public.gmane.org>
2005-03-23  0:54                                                   ` Li Shaohua
2005-03-23  3:57                                                     ` [ACPI] " Bjorn Helgaas
     [not found]                                                       ` <1110.65.74.231.82.1111550240.squirrel-TOYrGrLsdJ1xnVILBQAtiA@public.gmane.org>
2005-03-23 18:40                                                         ` Len Brown
2005-03-24 18:24                                                           ` Bjorn Helgaas
2005-03-25 19:07                                                             ` Len Brown
  -- strict thread matches above, loose matches on Subject: below --
2005-03-14  9:30 Li, Shaohua

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox