Re: [PATCH] ACPI: evaluate _PS3 when entering D3 Cold

[Lin Ming <ming.m.lin@intel.com>]

On Sun, 2012-04-01 at 09:23 +0200, Rafael J. Wysocki wrote:
> Hi,
> 
> Sorry for the delayed response, I've been travelling recently.
> 
> On Sunday, April 01, 2012, Lin Ming wrote:
> > On Sun, 2012-04-01 at 13:56 +0800, Aaron Lu wrote:
> > > Hi,
> > > 
> > > On Sun, Apr 01, 2012 at 01:27:33PM +0800, Lin Ming wrote:
> > > > > -		if (device->power.states[state].flags.explicit_set) {
> > > > > +		/* If state is D3 Cold, try to evaluate _PS3 first */
> > > > > +		if (state == ACPI_STATE_D3_COLD) {
> > > > > +			explicit_set = (ps - 1)->flags.explicit_set;
> > > > > +			object_name[3] -= 1;
> > > > > +		}
> > > > 
> > > > I'm not sure whether this works or not.
> > > > 
> > > > From ACPI spec,
> > > > 
> > > > _PS3 "is used to put the specific device into its D3hot or D3 state"
> > > > 
> > > > D3 neither means D3hot nor D3cold. It's an old term before D3hot and
> > > > D3cold were introduced.
> > > I guess D3 has to mean something, right? :-)
> 
> Well, not necessarily.
> 
> The problem is what state the _PS3 method puts the device into: D3_hot or
> D3_cold.
> 
> Unfortunately, as far as I can say, ACPI 4.0 didn't specify any "official"
> mapping between the "old" D3 and the "new" D3_{hod|cold} states, so we need to
> figure out something.  In my opinion, the only reasonable approach is to
> assume that the state _PS3 puts the device into is always D3_cold, becuase
> _PS3 may remove power completely from the device.  It may not do that, but
> we _must_ assume it does that in general.
> 
> > > Here is the problem, there is no _PR3 in AMD's implementation, just _PS3.
> > > And since _S0W evaluates 4, I've to put this device into D3 cold state
> > > with _PS3.
> > > 
> > > And the ACPI does have some words like:
> > > 
> > > ------
> > > Platform/drivers must assume that the device will have power completely
> > > removed when the device is place into “D3” via _PS3
> 
> Exactly.  What it means is basically "always reinitialize the device from
> scratch if you have run _PS3 on it".  And that's what we should do.
> 
> > > ------
> > > 
> > > This is in section 7.2.11: _PR3.
> > > 
> > > > 
> > > > Another problem:
> > > > 
> > > > With your patch, both D3hot and D3cold will evaluate _PS3, right?
> > > > 
> > > Yes.
> > > 
> > > > Will it have problem on AMD platform if you try to put ODD into D3hot
> > > > state? _PS3 is evaluated, so it actually enters D3Cold state.
> > > 
> > > There is no D3 hot support for this device(from the firmware's
> > > perspective), either it is at D0(via _PS0), or it will be at D3 cold(via
> > > _PS3).
> > 
> > But this is the generic code. We can't only consider some special
> > device.
> > 
> > Maybe we need some flag to tell which D3 state _PS3 is used for.
> 
> No, please.  As I said above, we need to reinitialize devices that _PS3 was
> executed on, which is equivalent to saying that those devices were put into
> D3_cold.
> 
> The only situation where a device can be put into ACPI D3_hot (which is not
> the same as PCI D3_hot, mind you) is when:
> 
> (1) There is _PR3 listing some of the device's power resources as "on".
> (2) The power resources listed by the _PR3 as "off" are turned off and the
>     power resources listed by the _PR3 as "on" are left in the "on" state.

(1) and (2) seems conflict.

(1) means all power resources listed in _PR3 are "on", but
(2) means some power resources listed in _PR3 are "off" and others are
"on"

Is my understanding correct?

Thanks,
Lin Ming

> 
> Our generic code should reflect that.
> 
> Thanks,
> Rafael


--
To unsubscribe from this list: send the line "unsubscribe linux-acpi" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html