From: JM <v-j-m@suomi24.fi>
To: linux-acpi@vger.kernel.org
Subject: Acer Aspire 9813WKMI fan runs all the time after suspend to ram
Date: Sat, 1 Dec 2007 14:53:46 +0100 (CET) [thread overview]
Message-ID: <17761706.1196517226756.JavaMail.apache@eni-cpps11.sth.basefarm.net> (raw)
Notebook fan runs all the time after suspend to ram.
After suspend to disk fan works OK.
after suspend to ram:
cat /proc/acpi/fan/FAN0/state
status: off
cat /proc/acpi/thermal_zone/TZ00/temperature
temperature: 27 C
cat /proc/acpi/thermal_zone/TZ01/temperature
temperature: 39 C
cat /proc/acpi/thermal_zone/TZ00/trip_points
critical (S5): 107 C
active[0]: 53 C: devices=FAN0
cat /proc/acpi/thermal_zone/TZ01/trip_points
critical (S5): 106 C
dmesg after boot:
[ 0.000000] Linux version 2.6.24-rc3-ge1cca7e8-15-default
(abuild@build15) (gcc version 4.2.1 (SUSE Linux))
#e1cca7e8d484390169777b423a7fe46c7021fec1 SMP 2007/25/30 01:25:2
[ 0.000000] Command line: root=/dev/disk/by-id/scsi-
SATA_SAMSUNG_HM120JIS09GJ30LB71446-part5 vga=0x348 resume=/dev/sda6
splash=silent
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009b400
(usable)
[ 0.000000] BIOS-e820: 000000000009b400 - 00000000000a0000
(reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 00000000000e0000
(reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000
(reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fe90000
(usable)
[ 0.000000] BIOS-e820: 000000007fe90000 - 000000007fe9a000 (ACPI
NVS)
[ 0.000000] BIOS-e820: 000000007fe9a000 - 0000000080000000
(reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000
(reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000
(reserved)
[ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed00400
(reserved)
[ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000
(reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000
(reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000
(reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000
(reserved)
[ 0.000000] Entering add_active_range(0, 0, 155) 0 entries of 3200
used
[ 0.000000] Entering add_active_range(0, 256, 523920) 1 entries of
3200 used
[ 0.000000] end_pfn_map = 1048576
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP 000F62A0, 0024 (r2 ACRSYS)
[ 0.000000] ACPI: XSDT 7FE91BC9, 0064 (r1 ACRSYS ACRPRDCT 6040000
LTP 0)
[ 0.000000] ACPI: FACP 7FE98C2A, 00F4 (r3 ACRSYS ACRPRDCT 6040000
ALAN 1)
[ 0.000000] ACPI: DSDT 7FE925BB, 65FB (r1 ACRSYS ACRPRDCT 6040000
INTL 20050624)
[ 0.000000] ACPI: FACS 7FE99FC0, 0040
[ 0.000000] ACPI: APIC 7FE98D1E, 0068 (r1 INTEL CALISTGA 6040000
LOHR 5A)
[ 0.000000] ACPI: HPET 7FE98D86, 0038 (r1 INTEL CALISTGA 6040000
LOHR 5A)
[ 0.000000] ACPI: MCFG 7FE98DBE, 003C (r1 INTEL CALISTGA 6040000
LOHR 5A)
[ 0.000000] ACPI: APIC 7FE98DFA, 0068 (r1 ACRSYS ACRPRDCT 6040000
LTP 0)
[ 0.000000] ACPI: SLIC 7FE98E62, 0176 (r1 ACRSYS ACRPRDCT 6040000
LTP 0)
[ 0.000000] ACPI: BOOT 7FE98FD8, 0028 (r1 PTLTD $SBFTBL$ 6040000
LTP 1)
[ 0.000000] ACPI: SSDT 7FE91C2D, 0500 (r1 PmRef CpuPm 3000
INTL 20050624)
[ 0.000000] ACPI: BIOS bug: multiple APIC/MADT found, using 0
[ 0.000000] ACPI: If "acpi_apic_instance=2" works better, notify
linux-acpi@vger.kernel.org
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-000000007fe90000
[ 0.000000] Entering add_active_range(0, 0, 155) 0 entries of 3200
used
[ 0.000000] Entering add_active_range(0, 256, 523920) 1 entries of
3200 used
[ 0.000000] Bootmem setup node 0 0000000000000000-000000007fe90000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 1048576
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0 -> 155
[ 0.000000] 0: 256 -> 523920
[ 0.000000] On node 0 totalpages: 523819
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 1403 pages reserved
[ 0.000000] DMA zone: 2536 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7106 pages used for memmap
[ 0.000000] DMA32 zone: 512718 pages, LIFO batch:31
[ 0.000000] Normal zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 (Bootup-CPU)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] Processor #1
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl
dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high
level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Setting APIC routing to flat
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] swsusp: Registered nosave memory region:
000000000009b000 - 000000000009c000
[ 0.000000] swsusp: Registered nosave memory region:
000000000009c000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region:
00000000000a0000 - 00000000000dc000
[ 0.000000] swsusp: Registered nosave memory region:
00000000000dc000 - 00000000000e0000
[ 0.000000] swsusp: Registered nosave memory region:
00000000000e0000 - 00000000000e4000
[ 0.000000] swsusp: Registered nosave memory region:
00000000000e4000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 88000000 (gap:
80000000:60000000)
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 46816 bytes of per cpu data
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on.
Total pages: 515254
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: root=/dev/disk/by-id/scsi-
SATA_SAMSUNG_HM120JIS09GJ30LB71446-part5 vga=0x348 resume=/dev/sda6
splash=silent
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] hpet clockevent registered
[ 0.000000] TSC calibrated against HPET
[ 23.221308] Marking TSC unstable due to TSCs unsynchronized
[ 23.221312] time.c: Detected 1662.499 MHz processor.
[ 23.221369] Console: colour dummy device 80x25
[ 23.221374] console [tty0] enabled
[ 23.221675] Checking aperture...
[ 23.221694] Calgary: detecting Calgary via BIOS EBDA area
[ 23.221697] Calgary: Unable to locate Rio Grande table in EBDA -
bailing!
[ 23.253921] Memory: 2056384k/2095680k available (2112k kernel code,
38892k reserved, 983k data, 324k init)
[ 23.331121] Calibrating delay using timer specific routine..
3329.33 BogoMIPS (lpj=6658673)
[ 23.331227] Security Framework initialized
[ 23.331239] Capability LSM initialized
[ 23.331677] Dentry cache hash table entries: 262144 (order: 9,
2097152 bytes)
[ 23.333496] Inode-cache hash table entries: 131072 (order: 8,
1048576 bytes)
[ 23.334385] Mount-cache hash table entries: 256
[ 23.334679] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 23.334690] CPU: L2 cache: 2048K
[ 23.334697] CPU 0/0 -> Node 0
[ 23.334702] using mwait in idle threads.
[ 23.334707] CPU: Physical Processor ID: 0
[ 23.334712] CPU: Processor Core ID: 0
[ 23.334726] CPU0: Thermal monitoring handled by SMI
[ 23.334751] SMP alternatives: switching to UP code
[ 23.335859] ACPI: Core revision 20070126
[ 23.343543] Parsing all Control Methods:
[ 23.343751] Table [DSDT](id 0001) - 995 Objects with 94 Devices 220
Methods 27 Regions
[ 23.343917] Parsing all Control Methods:
[ 23.344106] Table [SSDT](id 0002) - 13 Objects with 0 Devices 4
Methods 0 Regions
[ 23.344118] tbxface-0598 [00] tb_load_namespace : ACPI Tables
successfully acquired
[ 23.364362] evxfevnt-0091 [00] enable : Transition
to ACPI mode successful
[ 23.405170] Using local APIC timer interrupts.
[ 23.465238] APIC timer calibration result 10390617
[ 23.465242] Detected 10.390 MHz APIC timer.
[ 23.465403] SMP alternatives: switching to SMP code
[ 23.466267] Booting processor 1/2 APIC 0x1
[ 23.476843] Initializing CPU#1
[ 23.557111] Calibrating delay using timer specific routine..
3325.08 BogoMIPS (lpj=6650160)
[ 23.557122] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 23.557125] CPU: L2 cache: 2048K
[ 23.557129] CPU 1/1 -> Node 0
[ 23.557132] CPU: Physical Processor ID: 0
[ 23.557134] CPU: Processor Core ID: 1
[ 23.557146] CPU1: Thermal monitoring enabled (TM2)
[ 23.557699] Intel(R) Core(TM)2 CPU T5500 @ 1.66GHz
stepping 06
[ 23.557811] Brought up 2 CPUs
[ 23.558562] net_namespace: 120 bytes
[ 23.559339] NET: Registered protocol family 16
[ 23.559711] ACPI: bus type pci registered
[ 23.569420] PCI: Using MMCONFIG at e0000000 - efffffff
[ 23.573002] evgpeblk-0956 [00] ev_create_gpe_block : GPE 00 to 1F
[_GPE] 4 regs on int 0x9
[ 23.573702] evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 9
Wake, Enabled 1 Runtime GPEs in this block
[ 23.573721] ACPI: EC: Look up EC in DSDT
[ 23.576448] Completing Region/Field/Buffer/Package
initialization:..................................................................................................................................
[ 23.579691] Initialized 26/27 Regions 39/39 Fields 44/45 Buffers
21/39 Packages (1017 nodes)
[ 23.579704] Initializing Device/Processor/Thermal objects by
executing _INI methods:...
[ 23.589206] Executed 3 _INI methods requiring 0 _STA executions
(examined 100 objects)
[ 23.589248] ACPI: Interpreter enabled
[ 23.589255] ACPI: (supports S0 S3 S4 S5)
[ 23.589293] ACPI: Using IOAPIC for interrupt routing
[ 23.603021] ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data
= 0x62
[ 23.603031] ACPI: EC: driver started in poll mode
[ 23.603306] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 23.604033] PCI quirk: region 1000-107f claimed by ICH6
ACPI/GPIO/TCO
[ 23.604043] PCI quirk: region 1180-11bf claimed by ICH6 GPIO
[ 23.605759] PCI: Transparent bridge - 0000:00:1e.0
[ 23.605928] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 23.606644] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP.
_PRT]
[ 23.606966] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01.
_PRT]
[ 23.607284] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02.
_PRT]
[ 23.607597] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03.
_PRT]
[ 23.607909] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04.
_PRT]
[ 23.608250] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB.
_PRT]
[ 23.617059] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12
14 15) *11
[ 23.617291] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11
12 14 15)
[ 23.617514] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10
12 14 15)
[ 23.617736] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12
14 15) *10
[ 23.617959] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12
14 15) *0, disabled.
[ 23.618184] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12
14 15) *0, disabled.
[ 23.618407] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10
12 14 15)
[ 23.618628] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11 12
14 15)
[ 23.618928] ACPI: Power Resource [FN00] (off)
[ 23.619022] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 23.619089] pnp: PnP ACPI init
[ 23.619105] ACPI: bus type pnp registered
[ 23.639929] pnp: PnP ACPI: found 13 devices
[ 23.639938] ACPI: ACPI bus type pnp unregistered
[ 23.640389] PCI: Using ACPI for IRQ routing
[ 23.640397] PCI: If a device doesn't work, try "pci=routeirq". If
it helps, post a report
[ 23.661637] PCI-GART: No AMD northbridge found.
[ 23.661650] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 23.661661] hpet0: 3 64-bit timers, 14318180 Hz
[ 23.662748] ACPI: RTC can wake from S4
[ 23.664947] Time: hpet clocksource has been installed.
[ 23.664973] Switched to high resolution mode on CPU 0
[ 23.665604] Switched to high resolution mode on CPU 1
[ 23.673990] system 00:01: iomem range 0xe0000000-0xefffffff could
not be reserved
[ 23.674002] system 00:01: iomem range 0xfed14000-0xfed17fff could
not be reserved
[ 23.674013] system 00:01: iomem range 0xfed18000-0xfed18fff could
not be reserved
[ 23.674023] system 00:01: iomem range 0xfed19000-0xfed19fff could
not be reserved
[ 23.674033] system 00:01: iomem range 0xfed1c000-0xfed1ffff could
not be reserved
[ 23.674043] system 00:01: iomem range 0xfed20000-0xfed3ffff could
not be reserved
[ 23.674053] system 00:01: iomem range 0xfed45000-0xfed8ffff could
not be reserved
[ 23.674072] system 00:06: ioport range 0x400-0x401 has been
reserved
[ 23.674080] system 00:06: ioport range 0x680-0x69f has been
reserved
[ 23.674088] system 00:06: ioport range 0x800-0x80f has been
reserved
[ 23.674097] system 00:06: ioport range 0x1000-0x107f has been
reserved
[ 23.674105] system 00:06: ioport range 0x1180-0x11bf has been
reserved
[ 23.674113] system 00:06: ioport range 0x1640-0x164f has been
reserved
[ 23.674122] system 00:06: ioport range 0xfe10-0xfe11 has been
reserved
[ 23.674130] system 00:06: ioport range 0xfe00-0xfe00 has been
reserved
[ 23.674949] PCI: Failed to allocate mem resource #6:20000@d2000000
for 0000:01:00.0
[ 23.674960] PCI: Bridge: 0000:00:01.0
[ 23.674966] IO window: 2000-2fff
[ 23.674972] MEM window: d0000000-d1ffffff
[ 23.674978] PREFETCH window: b0000000-bfffffff
[ 23.674986] PCI: Bridge: 0000:00:1c.0
[ 23.674992] IO window: 3000-3fff
[ 23.675000] MEM window: cc000000-cdffffff
[ 23.675008] PREFETCH window: c4000000-c5ffffff
[ 23.675017] PCI: Bridge: 0000:00:1c.1
[ 23.675023] IO window: 4000-4fff
[ 23.675031] MEM window: c8000000-c9ffffff
[ 23.675039] PREFETCH window: c0000000-c1ffffff
[ 23.675047] PCI: Bridge: 0000:00:1c.2
[ 23.675054] IO window: 5000-5fff
[ 23.675062] MEM window: ca000000-cbffffff
[ 23.675069] PREFETCH window: c2000000-c3ffffff
[ 23.675078] PCI: Bridge: 0000:00:1c.3
[ 23.675084] IO window: 6000-6fff
[ 23.675093] MEM window: ce000000-cfffffff
[ 23.675100] PREFETCH window: c6000000-c7ffffff
[ 23.675120] PCI: Bus 10, cardbus bridge: 0000:09:06.0
[ 23.675126] IO window: 00001400-000014ff
[ 23.675134] IO window: 00001c00-00001cff
[ 23.675143] PREFETCH window: 88000000-8bffffff
[ 23.675151] MEM window: 8c000000-8fffffff
[ 23.675159] PCI: Bridge: 0000:00:1e.0
[ 23.675163] IO window: disabled.
[ 23.675172] MEM window: d2000000-d20fffff
[ 23.675179] PREFETCH window: disabled.
[ 23.675200] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level,
low) -> IRQ 16
[ 23.675212] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 23.675235] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level,
low) -> IRQ 17
[ 23.675248] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 23.675269] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level,
low) -> IRQ 16
[ 23.675282] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 23.675304] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level,
low) -> IRQ 18
[ 23.675317] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 23.675340] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level,
low) -> IRQ 19
[ 23.675353] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 23.675364] PCI: Enabling device 0000:00:1e.0 (0004 -> 0006)
[ 23.675374] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 23.675390] PCI: Enabling device 0000:09:06.0 (0000 -> 0003)
[ 23.675400] ACPI: PCI Interrupt 0000:09:06.0[A] -> GSI 21 (level,
low) -> IRQ 21
[ 23.675489] NET: Registered protocol family 2
[ 23.713252] IP route cache hash table entries: 65536 (order: 7,
524288 bytes)
[ 23.714630] TCP established hash table entries: 262144 (order: 10,
4194304 bytes)
[ 23.718036] TCP bind hash table entries: 65536 (order: 8, 1048576
bytes)
[ 23.718899] TCP: Hash tables configured (established 262144 bind
65536)
[ 23.718907] TCP reno registered
[ 23.729125] Unpacking initramfs... done
[ 24.045819] Freeing initrd memory: 4410k freed
[ 24.048746] Simple Boot Flag at 0x36 set to 0x1
[ 24.050281] audit: initializing netlink socket (disabled)
[ 24.050304] audit(1196522791.756:1): initialized
[ 24.050761] Total HugeTLB memory allocated, 0
[ 24.050987] VFS: Disk quotas dquot_6.5.1
[ 24.051039] Dquot-cache hash table entries: 512 (order 0, 4096
bytes)
[ 24.051322] Block layer SCSI generic (bsg) driver version 0.4
loaded (major 254)
[ 24.051334] io scheduler noop registered
[ 24.051339] io scheduler anticipatory registered
[ 24.051346] io scheduler deadline registered
[ 24.051377] io scheduler cfq registered (default)
[ 32.039690] 0000:00:1d.7 EHCI: BIOS handoff failed (BIOS bug ?)
01010001
[ 32.040568] Boot video device is 0000:01:00.0
[ 32.040818] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 32.040840] assign_interrupt_mode Found MSI capability
[ 32.040869] Allocate Port Service[0000:00:01.0:pcie00]
[ 32.040936] Allocate Port Service[0000:00:01.0:pcie03]
[ 32.041039] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 32.041089] assign_interrupt_mode Found MSI capability
[ 32.041133] Allocate Port Service[0000:00:1c.0:pcie00]
[ 32.041194] Allocate Port Service[0000:00:1c.0:pcie02]
[ 32.041254] Allocate Port Service[0000:00:1c.0:pcie03]
[ 32.041375] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 32.041425] assign_interrupt_mode Found MSI capability
[ 32.041469] Allocate Port Service[0000:00:1c.1:pcie00]
[ 32.041531] Allocate Port Service[0000:00:1c.1:pcie02]
[ 32.041589] Allocate Port Service[0000:00:1c.1:pcie03]
[ 32.041709] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 32.041759] assign_interrupt_mode Found MSI capability
[ 32.041803] Allocate Port Service[0000:00:1c.2:pcie00]
[ 32.041870] Allocate Port Service[0000:00:1c.2:pcie02]
[ 32.041928] Allocate Port Service[0000:00:1c.2:pcie03]
[ 32.042044] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 32.042094] assign_interrupt_mode Found MSI capability
[ 32.042138] Allocate Port Service[0000:00:1c.3:pcie00]
[ 32.042198] Allocate Port Service[0000:00:1c.3:pcie02]
[ 32.042260] Allocate Port Service[0000:00:1c.3:pcie03]
[ 32.042644] vesafb: framebuffer at 0xb0000000, mapped to
0xffffc20010980000, using 5742k, total 262144k
[ 32.042656] vesafb: mode is 1400x1050x16, linelength=2800, pages=1
[ 32.042663] vesafb: scrolling: redraw
[ 32.042670] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 32.105682] Console: switching to colour frame buffer device 175x65
[ 32.168798] fb0: VESA VGA frame buffer device
[ 32.174000] hpet_resources: 0xfed00000 is busy
[ 32.174108] Non-volatile memory driver v1.2
[ 32.174384] Linux agpgart interface v0.102
[ 32.174636] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports,
IRQ sharing disabled
[ 32.175340] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 32.176526] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 32.177303] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at
0x60,0x64 irq 1,12
[ 32.180444] i8042.c: Detected active multiplexing controller, rev
1.1.
[ 32.182265] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 32.182591] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 32.182930] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 32.183250] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 32.183601] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 32.184140] mice: PS/2 mouse device common for all mice
[ 32.218255] input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input0
[ 32.371965] input: PC Speaker as
/devices/platform/pcspkr/input/input1
[ 32.984524] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x12a0b1,
caps: 0xa04713/0x204000
[ 33.016882] input: SynPS/2 Synaptics TouchPad as
/devices/platform/i8042/serio4/input/input2
[ 33.044408] cpuidle: using governor ladder
[ 33.044677] cpuidle: using governor menu
[ 33.045048] NET: Registered protocol family 1
[ 33.045459] registered taskstats version 1
[ 33.045921] Freeing unused kernel memory: 324k freed
[ 33.104612] ACPI: SSDT 7FE9238A, 01A8 (r1 PmRef Cpu0Ist 3000
INTL 20050624)
[ 33.105211] Parsing all Control Methods:
[ 33.105727] Table [SSDT](id 00A1) - 5 Objects with 0 Devices 3
Methods 0 Regions
[ 33.106777] ACPI: SSDT 7FE9212D, 01D8 (r1 PmRef Cpu0Cst 3001
INTL 20050624)
[ 33.107299] Parsing all Control Methods:
[ 33.107805] Table [SSDT](id 00A2) - 1 Objects with 0 Devices 1
Methods 0 Regions
[ 33.109013] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 33.109426] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 33.110414] ACPI: SSDT 7FE92532, 0089 (r1 PmRef Cpu1Ist 3000
INTL 20050624)
[ 33.110969] Parsing all Control Methods:
[ 33.111484] Table [SSDT](id 00A7) - 3 Objects with 0 Devices 3
Methods 0 Regions
[ 33.112169] ACPI: SSDT 7FE92305, 0085 (r1 PmRef Cpu1Cst 3000
INTL 20050624)
[ 33.112692] Parsing all Control Methods:
[ 33.113204] Table [SSDT](id 00A8) - 1 Objects with 0 Devices 1
Methods 0 Regions
[ 33.114515] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 33.128091] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 33.147482] ACPI: Invalid passive threshold
[ 33.161510] ACPI: Thermal Zone [TZ00] (50 C)
[ 33.175878] ACPI: Thermal Zone [TZ01] (50 C)
[ 33.202237] SCSI subsystem initialized
[ 33.224626] libata version 3.00 loaded.
[ 33.233180] ahci 0000:00:1f.2: version 3.0
[ 33.233216] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level,
low) -> IRQ 19
[ 33.248924] ahci 0000:00:1f.2: nr_ports (4) and implemented port
map (0x5) don't match, using nr_ports
[ 33.264374] ahci 0000:00:1f.2: forcing PORTS_IMPL to 0xf
[ 33.284351] Clocksource tsc unstable (delta = -493461334 ns)
[ 33.302440] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5
Gbps 0xf impl RAID mode
[ 33.318831] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum
part
[ 33.335341] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 33.335703] scsi0 : ahci
[ 33.352555] scsi1 : ahci
[ 33.369279] scsi2 : ahci
[ 33.386025] scsi3 : ahci
[ 33.402883] ata1: SATA max UDMA/133 abar m1024@0xd2304400 port
0xd2304500 irq 4346
[ 33.420139] ata2: SATA max UDMA/133 abar m1024@0xd2304400 port
0xd2304580 irq 4346
[ 33.437381] ata3: SATA max UDMA/133 abar m1024@0xd2304400 port
0xd2304600 irq 4346
[ 33.454493] ata4: SATA max UDMA/133 abar m1024@0xd2304400 port
0xd2304680 irq 4346
[ 33.488880] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 33.515702] ata1.00: ATA-7: SAMSUNG HM120JI, YF100-10, max UDMA7
[ 33.533315] ata1.00: 234441648 sectors, multi 0: LBA48 NCQ (depth
31/32)
[ 33.557351] ata1.00: configured for UDMA/133
[ 33.578763] ata2: SATA link down (SStatus 0 SControl 0)
[ 33.600141] ata3: SATA link down (SStatus 0 SControl 300)
[ 33.621004] ata4: SATA link down (SStatus 0 SControl 0)
[ 33.639278] scsi 0:0:0:0: Direct-Access ATA SAMSUNG
HM120JI YF10 PQ: 0 ANSI: 5
[ 33.662850] ata_piix 0000:00:1f.1: version 2.12
[ 33.662872] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level,
low) -> IRQ 18
[ 33.681379] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 33.681494] scsi4 : ata_piix
[ 33.699943] scsi5 : ata_piix
[ 33.718226] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma
0x1880 irq 14
[ 33.736420] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma
0x1888 irq 15
[ 33.757197] ata5.01: ATAPI: MATSHITADVD-RAM UJ-85JS, F100, max
UDMA/33
[ 33.776928] ata5.01: configured for UDMA/33
[ 33.794528] ata6: port disabled. ignoring.
[ 33.795929] scsi 4:0:1:0: CD-ROM MATSHITA DVD-RAM UJ-
85JS F100 PQ: 0 ANSI: 5
[ 33.823531] ACPI: Fan [FAN0] (off)
[ 33.863111] BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
[ 34.198789] usbcore: registered new interface driver usbfs
[ 34.217208] usbcore: registered new interface driver hub
[ 34.240983] usbcore: registered new device driver usb
[ 34.259154] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors
(120034 MB)
[ 34.277396] sd 0:0:0:0: [sda] Write Protect is off
[ 34.295185] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 34.295229] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 34.295259] USB Universal Host Controller Interface driver v3.0
[ 34.331661] ACPI: PCI Interrupt 0000:00:1d.0[A] -> <5>sd 0:0:0:0:
[sda] 234441648 512-byte hardware sectors (120034 MB)
[ 34.331975] sd 0:0:0:0: [sda] Write Protect is off
[ 34.331979] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 34.332009] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 34.332013] sda:GSI 23 (level, low) -> IRQ 23
[ 34.412552] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 34.412560] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 34.431588] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned
bus number 1
[ 34.468579] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001800
[ 34.490782] usb usb1: configuration #1 chosen from 1 choice
[ 34.513085] hub 1-0:1.0: USB hub found
[ 34.531640] hub 1-0:1.0: 2 ports detected
[ 34.654447] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level,
low) -> IRQ 23
[ 34.673502] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 34.673511] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 34.691687] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned
bus number 2
[ 34.713912] ehci_hcd 0000:00:1d.7: debug port 1
[ 34.731788] PCI: cache line size of 32 is not supported by device
0000:00:1d.7
[ 34.731799] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd2304000
[ 34.766060] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00,
driver 10 Dec 2004
[ 34.784234] usb usb2: configuration #1 chosen from 1 choice
[ 34.801670] sda1<6>hub 2-0:1.0: USB hub found
[ 34.801720] hub 2-0:1.0: 8 ports detected
[ 34.836304] sda2 sda3 < sda5 sda6 >
[ 34.894098] sd 0:0:0:0: [sda] Attached SCSI disk
[ 34.911975] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level,
low) -> IRQ 19
[ 34.929589] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 34.929595] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 34.947385] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned
bus number 3
[ 34.965415] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001820
[ 34.983527] usb usb3: configuration #1 chosen from 1 choice
[ 35.001358] hub 3-0:1.0: USB hub found
[ 35.019039] hub 3-0:1.0: 2 ports detected
[ 35.137658] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level,
low) -> IRQ 18
[ 35.155209] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 35.155215] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 35.172468] usb 2-6: new high speed USB device using ehci_hcd and
address 2
[ 35.190360] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned
bus number 4
[ 35.208627] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001840
[ 35.227013] usb usb4: configuration #1 chosen from 1 choice
[ 35.245218] hub 4-0:1.0: USB hub found
[ 35.263561] hub 4-0:1.0: 2 ports detected
[ 35.330017] usb 2-6: configuration #1 chosen from 1 choice
[ 35.362067] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level,
low) -> IRQ 16
[ 35.380704] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 35.380711] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 35.399234] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned
bus number 5
[ 35.418083] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001860
[ 35.436723] usb usb5: configuration #1 chosen from 1 choice
[ 35.455447] hub 5-0:1.0: USB hub found
[ 35.474109] hub 5-0:1.0: 2 ports detected
[ 35.657720] swsusp: Marking nosave pages: 000000000009b000 -
0000000000100000
[ 35.657733] swsusp: Basic memory bitmaps created
[ 35.694387] swsusp: Basic memory bitmaps freed
[ 35.723147] Attempting manual resume
[ 36.491855] kjournald starting. Commit interval 5 seconds
[ 36.492152] EXT3 FS on sda5, internal journal
[ 36.492160] EXT3-fs: mounted filesystem with ordered data mode.
[ 39.231900] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 39.250469] scsi 4:0:1:0: Attached scsi generic sg1 type 5
[ 39.599245] ACPI: AC Adapter [ADP0] (on-line)
[ 39.639314] input: Power Button (FF) as
/devices/virtual/input/input3
[ 39.661648] ACPI: Battery Slot [BAT0] (battery absent)
[ 39.708445] iTCO_vendor_support: vendor-support=0
[ 39.746820] ACPI: Power Button (FF) [PWRF]
[ 39.766322] input: Lid Switch as /devices/virtual/input/input4
[ 39.792381] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[ 39.811391] rtc0: alarms up to one month, y3k
[ 39.838777] ACPI: Lid Switch [LID]
[ 39.858294] input: Power Button (CM) as
/devices/virtual/input/input5
[ 39.886182] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw
xa/form2 cdda caddy
[ 39.905993] Uniform CD-ROM driver Revision: 3.20
[ 39.925525] sr 4:0:1:0: Attached scsi CD-ROM sr0
[ 39.951685] ACPI: Power Button (CM) [PWRB]
[ 39.971642] input: Sleep Button (CM) as
/devices/virtual/input/input6
[ 39.991432] NET: Registered protocol family 23
[ 40.021731] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level,
low) -> IRQ 16
[ 40.041493] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 40.042428] sky2 0000:02:00.0: v1.20 addr 0xcc000000 irq 16 Yukon-
EC Ultra (0xb4) rev 3
[ 40.063673] sky2 eth0: addr 00:a0:d1:a1:41:72
[ 40.093072] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-
2007)
[ 40.113453] iTCO_wdt: Found a ICH7-M DH TCO device (Version=2,
TCOBASE=0x1060)
[ 40.133806] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 40.159297] parport_pc 00:0a: reported by Plug and Play ACPI
[ 40.179465] parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 40.206590] ACPI: Sleep Button (CM) [SLPB]
[ 40.227306] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level,
low) -> IRQ 19
[ 40.266954] ACPI: PCI Interrupt 0000:09:06.1[B] -> GSI 20 (level,
low) -> IRQ 20
[ 40.287256] PCI: Setting latency timer of device 0000:09:06.1 to 64
[ 40.339174] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=
[d2005800-d2005fff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 40.363158] PCI: Enabling device 0000:09:06.2 (0000 -> 0002)
[ 40.384559] ACPI: PCI Interrupt 0000:09:06.2[A] -> GSI 21 (level,
low) -> IRQ 21
[ 40.405868] PCI: Setting latency timer of device 0000:09:06.2 to 64
[ 40.412186] intel_rng: FWH not detected
[ 40.438375] sdhci: Secure Digital Host Controller Interface driver
[ 40.459613] sdhci: Copyright(c) Pierre Ossman
[ 40.481038] sdhci: SDHCI controller found at 0000:09:06.3 [104c:
803c] (rev 0)
[ 40.518390] PCI: Enabling device 0000:09:06.3 (0000 -> 0002)
[ 40.539598] ACPI: PCI Interrupt 0000:09:06.3[A] -> GSI 21 (level,
low) -> IRQ 21
[ 40.561207] found SMC SuperIO Chip (devid=0x7a rev=01 base=0x004e):
LPC47N227
[ 40.583591] smsc_superio_flat(): IrDA not enabled
[ 40.583988] PCI: Setting latency timer of device 0000:09:06.3 to 64
[ 40.584749] mmc0: SDHCI at 0xd2006000 irq 21 DMA
[ 40.626131] smsc_superio_flat(): fir: 0x00, sir: 0x00, dma: 15,
irq: 0, mode: 0x02
[ 40.650718] Yenta: CardBus bridge found at 0000:09:06.0 [1025:006c]
[ 40.672208] Yenta: Enabling burst memory read transactions
[ 40.694147] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 40.716000] Yenta: Routing CardBus interrupts to PCI
[ 40.737851] Yenta TI: socket 0000:09:06.0, mfunc 0x01a61b22, devctl
0x66
[ 40.767585] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level,
low) -> IRQ 22
[ 40.790792] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 40.990762] Yenta: ISA IRQ mask 0x0c78, PCI irq 21
[ 41.011775] Socket status: 30000006
[ 41.032580] Yenta: Raising subordinate bus# of parent bus (#09)
from #09 to #0d
[ 41.033210] ALSA sound/pci/hda/hda_codec.c:2140: hda_codec: model
'acer' is selected
[ 41.075083] pcmcia: parent PCI bridge Memory window: 0xd2000000 -
0xd20fffff
[ 41.853522] nvidia: module license 'NVIDIA' taints kernel.
[ 42.131477] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level,
low) -> IRQ 16
[ 42.152369] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 42.152545] NVRM: loading NVIDIA UNIX x86_64 Kernel Module
100.14.19 Wed Sep 12 14:08:38 PDT 2007
[ 42.317594] Adding 1052216k swap on /dev/sda6. Priority:-1 extents:
1 across:1052216k
[ 42.604053] device-mapper: uevent: version 1.0.3
[ 42.626183] device-mapper: ioctl: 4.12.0-ioctl (2007-10-02)
initialised: dm-devel@redhat.com
[ 43.119070] loop: module loaded
[ 43.452390] fuse init (API version 7.9)
[ 48.299978] IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.
fsnet.co.uk>
[ 57.892547] sky2 eth0: enabling interface
[ 58.824728] NET: Registered protocol family 17
[ 60.878729] sky2 eth0: Link is up at 100 Mbps, full duplex, flow
control both
[ 63.637884] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 63.855577] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 63.966739] audit(1196515635.955:2): audit_backlog_limit=320 old=64
by auid=4294967295 res=1
[ 63.971515] audit(1196515635.959:3): audit_pid=2981 old=0 by
auid=4294967295
[ 80.671219] ACPI: EC: non-query interrupt received, switching to
interrupt mode
dmesg after suspend to ram:
[ 115.560694] Syncing filesystems ... done.
[ 116.034375] Freezing user space processes ... (elapsed 0.00
seconds) done.
[ 116.034932] Freezing remaining freezable tasks ... (elapsed 0.00
seconds) done.
[ 116.034997] Suspending console(s)
[ 116.035106] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 116.035243] sd 0:0:0:0: [sda] Stopping disk
[ 116.505352] parport_pc 00:0a: disabled
[ 116.505663] serial 00:09: disabled
[ 116.505690] ACPI handle has no context!
[ 116.505755] ACPI handle has no context!
[ 116.505779] ACPI: PCI interrupt for device 0000:09:06.3 disabled
[ 116.505786] ACPI handle has no context!
[ 116.505926] ACPI handle has no context!
[ 116.505941] ACPI: PCI interrupt for device 0000:09:06.2 disabled
[ 116.505948] ACPI handle has no context!
[ 116.506091] ieee1394: hpsb_bus_reset called while bus reset already
in progress
[ 116.506152] ACPI handle has no context!
[ 116.522330] sky2 eth0: disabling interface
[ 116.527158] ACPI handle has no context!
[ 116.527198] NVRM: RmPowerManagement: 3
[ 117.684341] ACPI: PCI interrupt for device 0000:00:1f.1 disabled
[ 117.684463] ACPI: PCI interrupt for device 0000:00:1d.7 disabled
[ 117.684608] ACPI: PCI interrupt for device 0000:00:1d.3 disabled
[ 117.684639] ACPI: PCI interrupt for device 0000:00:1d.2 disabled
[ 117.684669] ACPI: PCI interrupt for device 0000:00:1d.1 disabled
[ 117.684700] ACPI: PCI interrupt for device 0000:00:1d.0 disabled
[ 117.684904] ACPI: PCI interrupt for device 0000:00:1b.0 disabled
[ 117.715490] Disabling non-boot CPUs ...
[ 117.828746] CPU 1 is now offline
[ 117.828751] SMP alternatives: switching to UP code
[ 117.831037] CPU1 is down
[ 117.831166] Extended CMOS year: 2000
[ 117.831722] hwsleep-0317 [00] enter_sleep_state : Entering
sleep state [S3]
[ 0.581850] Back to C!
[ 0.582193] Extended CMOS year: 2000
[ 0.582303] Enabling non-boot CPUs ...
[ 0.591885] SMP alternatives: switching to SMP code
[ 0.593255] Booting processor 1/2 APIC 0x1
[ 0.603694] Initializing CPU#1
[ 0.683597] Calibrating delay using timer specific routine..
3324.90 BogoMIPS (lpj=6649814)
[ 0.683609] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.683612] CPU: L2 cache: 2048K
[ 0.683617] CPU 1/1 -> Node 0
[ 0.683619] CPU: Physical Processor ID: 0
[ 0.683622] CPU: Processor Core ID: 1
[ 0.684176] Intel(R) Core(TM)2 CPU T5500 @ 1.66GHz
stepping 06
[ 0.684862] CPU1 is up
[ 0.688267] Switched to high resolution mode on CPU 1
[ 0.725390] PM: Writing back config space on device 0000:00:01.0 at
offset f (was 100, writing 1c010b)
[ 0.725398] PM: Writing back config space on device 0000:00:01.0 at
offset a (was f, writing 0)
[ 0.725403] PM: Writing back config space on device 0000:00:01.0 at
offset 9 (was 1fff1, writing bff1b001)
[ 0.725408] PM: Writing back config space on device 0000:00:01.0 at
offset 8 (was fff0, writing d1f0d000)
[ 0.725413] PM: Writing back config space on device 0000:00:01.0 at
offset 7 (was f0, writing 2020)
[ 0.725418] PM: Writing back config space on device 0000:00:01.0 at
offset 3 (was 10000, writing 10010)
[ 0.725423] PM: Writing back config space on device 0000:00:01.0 at
offset 1 (was 100000, writing 100407)
[ 0.725437] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 0.725570] PM: Writing back config space on device 0000:00:1b.0 at
offset 3 (was 0, writing 10)
[ 0.725578] PM: Writing back config space on device 0000:00:1b.0 at
offset 1 (was 100006, writing 100002)
[ 0.725601] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level,
low) -> IRQ 22
[ 0.725610] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 0.725637] PM: Writing back config space on device 0000:00:1c.0 at
offset f (was 40100, writing 4010b)
[ 0.725650] PM: Writing back config space on device 0000:00:1c.0 at
offset 9 (was 10001, writing c5f1c401)
[ 0.725656] PM: Writing back config space on device 0000:00:1c.0 at
offset 8 (was 0, writing cdf0cc00)
[ 0.725662] PM: Writing back config space on device 0000:00:1c.0 at
offset 7 (was 20000000, writing 20003030)
[ 0.725669] PM: Writing back config space on device 0000:00:1c.0 at
offset 6 (was 0, writing 20200)
[ 0.725677] PM: Writing back config space on device 0000:00:1c.0 at
offset 3 (was 810000, writing 810010)
[ 0.725685] PM: Writing back config space on device 0000:00:1c.0 at
offset 1 (was 100000, writing 100407)
[ 0.725718] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.725730] PM: Writing back config space on device 0000:00:1c.1 at
offset f (was 40200, writing 4020b)
[ 0.725742] PM: Writing back config space on device 0000:00:1c.1 at
offset 9 (was 10001, writing c1f1c001)
[ 0.725748] PM: Writing back config space on device 0000:00:1c.1 at
offset 8 (was 0, writing c9f0c800)
[ 0.725755] PM: Writing back config space on device 0000:00:1c.1 at
offset 7 (was 20000000, writing 4040)
[ 0.725764] PM: Writing back config space on device 0000:00:1c.1 at
offset 3 (was 810000, writing 810010)
[ 0.725772] PM: Writing back config space on device 0000:00:1c.1 at
offset 1 (was 100000, writing 100407)
[ 0.725805] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.725817] PM: Writing back config space on device 0000:00:1c.2 at
offset f (was 40300, writing 4030a)
[ 0.725829] PM: Writing back config space on device 0000:00:1c.2 at
offset 9 (was 10001, writing c3f1c201)
[ 0.725835] PM: Writing back config space on device 0000:00:1c.2 at
offset 8 (was 0, writing cbf0ca00)
[ 0.725842] PM: Writing back config space on device 0000:00:1c.2 at
offset 7 (was 20000000, writing 5050)
[ 0.725848] PM: Writing back config space on device 0000:00:1c.2 at
offset 6 (was 0, writing 60500)
[ 0.725857] PM: Writing back config space on device 0000:00:1c.2 at
offset 3 (was 810000, writing 810010)
[ 0.725864] PM: Writing back config space on device 0000:00:1c.2 at
offset 1 (was 100000, writing 100407)
[ 0.725898] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 0.725909] PM: Writing back config space on device 0000:00:1c.3 at
offset f (was 40400, writing 4040a)
[ 0.725921] PM: Writing back config space on device 0000:00:1c.3 at
offset 9 (was 10001, writing c7f1c601)
[ 0.725928] PM: Writing back config space on device 0000:00:1c.3 at
offset 8 (was 0, writing cff0ce00)
[ 0.725934] PM: Writing back config space on device 0000:00:1c.3 at
offset 7 (was 20000000, writing 6060)
[ 0.725944] PM: Writing back config space on device 0000:00:1c.3 at
offset 3 (was 810000, writing 810010)
[ 0.725951] PM: Writing back config space on device 0000:00:1c.3 at
offset 1 (was 100000, writing 100407)
[ 0.725984] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 0.725995] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level,
low) -> IRQ 23
[ 0.726002] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 0.726049] usb usb1: root hub lost power or was reset
[ 0.726072] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level,
low) -> IRQ 19
[ 0.726079] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 0.726125] usb usb3: root hub lost power or was reset
[ 0.726146] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level,
low) -> IRQ 18
[ 0.726153] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 0.726198] usb usb4: root hub lost power or was reset
[ 0.726219] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level,
low) -> IRQ 16
[ 0.726225] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 0.726271] usb usb5: root hub lost power or was reset
[ 0.726400] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level,
low) -> IRQ 23
[ 0.726407] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 0.726469] PM: Writing back config space on device 0000:00:1e.0 at
offset 9 (was 10001, writing 1fff1)
[ 0.726478] PM: Writing back config space on device 0000:00:1e.0 at
offset 8 (was 0, writing d200d200)
[ 0.726485] PM: Writing back config space on device 0000:00:1e.0 at
offset 7 (was 22800000, writing 228000f0)
[ 0.726493] PM: Writing back config space on device 0000:00:1e.0 at
offset 6 (was 20090900, writing 200d0900)
[ 0.726508] PM: Writing back config space on device 0000:00:1e.0 at
offset 1 (was 100004, writing 100006)
[ 0.726528] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.726577] PM: Writing back config space on device 0000:00:1f.1 at
offset f (was 100, writing 1ff)
[ 0.726598] PM: Writing back config space on device 0000:00:1f.1 at
offset 1 (was 2880000, writing 2880005)
[ 0.726610] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level,
low) -> IRQ 18
[ 0.726617] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 0.726694] ata6: port disabled. ignoring.
[ 0.727974] PM: Writing back config space on device 0000:00:1f.2 at
offset f (was 200, writing 20a)
[ 0.727997] PM: Writing back config space on device 0000:00:1f.2 at
offset 1 (was 2b00007, writing 2b00407)
[ 0.728033] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 0.733167] ata5.01: configured for UDMA/33
[ 0.734093] NVRM: RmPowerManagement: 4
[ 1.038920] ata2: SATA link down (SStatus 0 SControl 0)
[ 1.038996] ata4: SATA link down (SStatus 0 SControl 0)
[ 1.039037] ata3: SATA link down (SStatus 0 SControl 300)
[ 1.522163] PM: Writing back config space on device 0000:02:00.0 at
offset f (was 100, writing 10b)
[ 1.522189] PM: Writing back config space on device 0000:02:00.0 at
offset 6 (was 1, writing 3001)
[ 1.522198] PM: Writing back config space on device 0000:02:00.0 at
offset 4 (was 4, writing cc000004)
[ 1.522204] PM: Writing back config space on device 0000:02:00.0 at
offset 3 (was 0, writing 10)
[ 1.522213] PM: Writing back config space on device 0000:02:00.0 at
offset 1 (was 100000, writing 100407)
[ 1.522443] sky2 eth0: enabling interface
[ 1.525090] PM: Writing back config space on device 0000:07:00.0 at
offset f (was 100, writing 10a)
[ 1.525152] PM: Writing back config space on device 0000:07:00.0 at
offset 4 (was 0, writing ce000000)
[ 1.525164] PM: Writing back config space on device 0000:07:00.0 at
offset 3 (was 0, writing 10)
[ 1.525181] PM: Writing back config space on device 0000:07:00.0 at
offset 1 (was 100000, writing 100006)
[ 1.525241] PM: Writing back config space on device 0000:09:04.0 at
offset f (was 100, writing 10b)
[ 1.525260] PM: Writing back config space on device 0000:09:04.0 at
offset 4 (was 0, writing d2005000)
[ 1.525287] PM: Writing back config space on device 0000:09:06.0 at
offset f (was 34001ff, writing 5c001ff)
[ 1.525293] PM: Writing back config space on device 0000:09:06.0 at
offset e (was 0, writing 1cfc)
[ 1.525298] PM: Writing back config space on device 0000:09:06.0 at
offset d (was 0, writing 1c00)
[ 1.525302] PM: Writing back config space on device 0000:09:06.0 at
offset c (was 0, writing 14fc)
[ 1.525308] PM: Writing back config space on device 0000:09:06.0 at
offset b (was 0, writing 1400)
[ 1.525313] PM: Writing back config space on device 0000:09:06.0 at
offset a (was 0, writing 8ffff000)
[ 1.525318] PM: Writing back config space on device 0000:09:06.0 at
offset 9 (was 0, writing 8c000000)
[ 1.525323] PM: Writing back config space on device 0000:09:06.0 at
offset 8 (was 0, writing 8bfff000)
[ 1.525328] PM: Writing back config space on device 0000:09:06.0 at
offset 7 (was 0, writing 88000000)
[ 1.525333] PM: Writing back config space on device 0000:09:06.0 at
offset 6 (was 0, writing b00d0a09)
[ 1.525340] PM: Writing back config space on device 0000:09:06.0 at
offset 4 (was 0, writing d2007000)
[ 1.525345] PM: Writing back config space on device 0000:09:06.0 at
offset 3 (was 820000, writing 82a820)
[ 1.525352] PM: Writing back config space on device 0000:09:06.0 at
offset 1 (was 2100000, writing 2100007)
[ 1.677925] PM: Writing back config space on device 0000:09:06.1 at
offset f (was 4020200, writing 402020b)
[ 1.677949] PM: Writing back config space on device 0000:09:06.1 at
offset 5 (was 0, writing d2000000)
[ 1.677956] PM: Writing back config space on device 0000:09:06.1 at
offset 4 (was 0, writing d2005800)
[ 1.677963] PM: Writing back config space on device 0000:09:06.1 at
offset 3 (was 800000, writing 804000)
[ 1.677972] PM: Writing back config space on device 0000:09:06.1 at
offset 1 (was 2100000, writing 2100006)
[ 1.728013] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=
[d2005800-d2005fff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 1.741825] PM: Writing back config space on device 0000:09:06.2 at
offset f (was 40701ff, writing 407010b)
[ 1.741849] PM: Writing back config space on device 0000:09:06.2 at
offset 4 (was 0, writing d2004000)
[ 1.741855] PM: Writing back config space on device 0000:09:06.2 at
offset 3 (was 800000, writing 804000)
[ 1.741864] PM: Writing back config space on device 0000:09:06.2 at
offset 1 (was 2100000, writing 2100006)
[ 1.741888] ACPI: PCI Interrupt 0000:09:06.2[A] -> GSI 21 (level,
low) -> IRQ 21
[ 1.757797] PM: Writing back config space on device 0000:09:06.3 at
offset f (was 40701ff, writing 407010b)
[ 1.757820] PM: Writing back config space on device 0000:09:06.3 at
offset 4 (was 0, writing d2006000)
[ 1.757826] PM: Writing back config space on device 0000:09:06.3 at
offset 3 (was 800000, writing 804000)
[ 1.757834] PM: Writing back config space on device 0000:09:06.3 at
offset 1 (was 2100000, writing 2100006)
[ 1.757858] ACPI: PCI Interrupt 0000:09:06.3[A] -> GSI 21 (level,
low) -> IRQ 21
[ 1.759176] serial 00:09: activated
[ 1.760821] parport_pc 00:0a: activated
[ 2.204536] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.216471] ata1.00: configured for UDMA/133
[ 2.217848] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors
(120034 MB)
[ 2.217888] sd 0:0:0:0: [sda] Write Protect is off
[ 2.217892] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.217961] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 2.232235] sd 0:0:0:0: [sda] Starting disk
[ 2.311647] Restarting tasks ... done.
[ 2.440281] usb 2-6: USB disconnect, address 2
[ 2.584158] ieee1394: Host added: ID:BUS[0-00:1023] GUID
[00a0d1a0d1a14172]
[ 2.679893] usb 2-6: new high speed USB device using ehci_hcd and
address 3
[ 2.828096] usb 2-6: configuration #1 chosen from 1 choice
[ 4.457989] sky2 eth0: Link is up at 100 Mbps, full duplex, flow
control both
dmesg after suspend to disk
[ 127.231046] swsusp: Marking nosave pages: 000000000009b000 -
0000000000100000
[ 127.231061] swsusp: Basic memory bitmaps created
[ 127.231064] Syncing filesystems ... done.
[ 128.094581] Freezing user space processes ... (elapsed 0.00
seconds) done.
[ 128.095245] Freezing remaining freezable tasks ... (elapsed 0.00
seconds) done.
[ 128.095306] Shrinking memory... \b-\bdone (0 pages freed)
[ 128.199771] Freed 0 kbytes in 0.10 seconds (0.00 MB/s)
[ 128.199773] Suspending console(s)
[ 128.199895] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 128.368758] parport_pc 00:0a: disabled
[ 128.369056] serial 00:09: disabled
[ 128.369080] ACPI handle has no context!
[ 128.369144] ACPI handle has no context!
[ 128.369167] ACPI: PCI interrupt for device 0000:09:06.3 disabled
[ 128.369174] ACPI handle has no context!
[ 128.369314] ACPI handle has no context!
[ 128.369329] ACPI: PCI interrupt for device 0000:09:06.2 disabled
[ 128.369336] ACPI handle has no context!
[ 128.369476] ieee1394: hpsb_bus_reset called while bus reset already
in progress
[ 128.369539] ACPI handle has no context!
[ 128.385715] sky2 eth0: disabling interface
[ 128.390545] ACPI handle has no context!
[ 128.390580] NVRM: RmPowerManagement: 3
[ 129.789775] ACPI: PCI interrupt for device 0000:00:1f.1 disabled
[ 129.789895] ACPI: PCI interrupt for device 0000:00:1d.7 disabled
[ 129.790165] ACPI: PCI interrupt for device 0000:00:1d.3 disabled
[ 129.790196] ACPI: PCI interrupt for device 0000:00:1d.2 disabled
[ 129.790227] ACPI: PCI interrupt for device 0000:00:1d.1 disabled
[ 129.790257] ACPI: PCI interrupt for device 0000:00:1d.0 disabled
[ 129.790463] ACPI: PCI interrupt for device 0000:00:1b.0 disabled
[ 129.850667] Disabling non-boot CPUs ...
[ 129.962255] CPU 1 is now offline
[ 129.962260] SMP alternatives: switching to UP code
[ 129.964571] CPU1 is down
[ 129.964703] Extended CMOS year: 2000
[ 129.964807] swsusp: critical section:
[ 130.101859] swsusp: Need to copy 125356 pages
[ 55.457320] evxfevnt-0079 [00] enable : System is
already in ACPI mode
[ 55.457662] Extended CMOS year: 2000
[ 55.457772] Enabling non-boot CPUs ...
[ 55.467326] SMP alternatives: switching to SMP code
[ 55.468697] Booting processor 1/2 APIC 0x1
[ 55.479127] Initializing CPU#1
[ 55.559036] Calibrating delay using timer specific routine..
3324.98 BogoMIPS (lpj=6649971)
[ 55.559047] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 55.559051] CPU: L2 cache: 2048K
[ 55.559055] CPU 1/1 -> Node 0
[ 55.559058] CPU: Physical Processor ID: 0
[ 55.559060] CPU: Processor Core ID: 1
[ 55.559614] Intel(R) Core(TM)2 CPU T5500 @ 1.66GHz
stepping 06
[ 55.560274] CPU1 is up
[ 55.560280] evxfevnt-0079 [00] enable : System is
already in ACPI mode
[ 55.573855] Switched to high resolution mode on CPU 1
[ 56.031989] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 56.046311] PM: Writing back config space on device 0000:00:1b.0 at
offset 1 (was 100006, writing 100002)
[ 56.046334] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level,
low) -> IRQ 22
[ 56.046343] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 56.046379] PM: Writing back config space on device 0000:00:1c.0 at
offset 7 (was 3030, writing 20003030)
[ 56.046419] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 56.046477] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 56.046532] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 56.046588] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 56.046599] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level,
low) -> IRQ 23
[ 56.046606] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 56.046655] usb usb1: root hub lost power or was reset
[ 56.046677] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level,
low) -> IRQ 19
[ 56.046684] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 56.046731] usb usb2: root hub lost power or was reset
[ 56.046751] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level,
low) -> IRQ 18
[ 56.046757] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 56.046804] usb usb3: root hub lost power or was reset
[ 56.046827] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level,
low) -> IRQ 16
[ 56.046834] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 56.046884] usb usb4: root hub lost power or was reset
[ 56.062254] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level,
low) -> IRQ 23
[ 56.062261] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 56.062300] usb usb5: root hub lost power or was reset
[ 56.066172] ehci_hcd 0000:00:1d.7: debug port 1
[ 56.066179] PCI: cache line size of 32 is not supported by device
0000:00:1d.7
[ 56.066203] PM: Writing back config space on device 0000:00:1e.0 at
offset 6 (was 20090900, writing 200d0900)
[ 56.066228] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 56.066295] PM: Writing back config space on device 0000:00:1f.1 at
offset 1 (was 2880001, writing 2880005)
[ 56.066307] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level,
low) -> IRQ 18
[ 56.066313] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 56.066362] PM: Writing back config space on device 0000:00:1f.2 at
offset 1 (was 2b00403, writing 2b00407)
[ 56.066398] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 56.066525] NVRM: RmPowerManagement: 4
[ 56.067572] ata6: port disabled. ignoring.
[ 56.381749] ata3: SATA link down (SStatus 0 SControl 300)
[ 56.381767] ata2: SATA link down (SStatus 0 SControl 0)
[ 56.381784] ata4: SATA link down (SStatus 0 SControl 0)
[ 56.545487] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 56.557749] ata1.00: configured for UDMA/133
[ 56.573484] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors
(120034 MB)
[ 56.573504] sd 0:0:0:0: [sda] Write Protect is off
[ 56.573508] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 56.573539] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 56.729748] ata5.01: configured for UDMA/33
[ 57.923360] PM: Writing back config space on device 0000:02:00.0 at
offset 1 (was 100007, writing 100407)
[ 57.923592] sky2 eth0: enabling interface
[ 57.926442] PM: Writing back config space on device 0000:09:06.0 at
offset f (was 34001ff, writing 5c001ff)
[ 57.926464] PM: Writing back config space on device 0000:09:06.0 at
offset 3 (was 823100, writing 82a820)
[ 58.079078] PM: Writing back config space on device 0000:09:06.1 at
offset 3 (was 800000, writing 804000)
[ 58.129053] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=
[d2005800-d2005fff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 58.142981] PM: Writing back config space on device 0000:09:06.2 at
offset 3 (was 800000, writing 804000)
[ 58.142988] PM: Writing back config space on device 0000:09:06.2 at
offset 1 (was 2100000, writing 2100006)
[ 58.143009] ACPI: PCI Interrupt 0000:09:06.2[A] -> GSI 21 (level,
low) -> IRQ 21
[ 58.158944] PM: Writing back config space on device 0000:09:06.3 at
offset 3 (was 800000, writing 804000)
[ 58.158951] PM: Writing back config space on device 0000:09:06.3 at
offset 1 (was 2100000, writing 2100006)
[ 58.158967] ACPI: PCI Interrupt 0000:09:06.3[A] -> GSI 21 (level,
low) -> IRQ 21
[ 58.159656] serial 00:09: activated
[ 58.160705] parport_pc 00:0a: activated
[ 58.733362] sd 0:0:0:0: [sda] Starting disk
[ 59.671044] Restarting tasks ... done.
[ 59.704359] swsusp: Basic memory bitmaps freed
[ 59.865406] usb 5-6: USB disconnect, address 2
[ 59.977050] usb 5-6: new high speed USB device using ehci_hcd and
address 3
[ 60.005109] ieee1394: Host added: ID:BUS[0-00:1023] GUID
[00a0d1a0d1a14172]
[ 60.125127] usb 5-6: configuration #1 chosen from 1 choice
[ 61.740221] sky2 eth0: Link is up at 100 Mbps, full duplex, flow
control both
[ 64.660255] ACPI: EC: non-query interrupt received, switching to
interrupt mode
next reply other threads:[~2007-12-01 14:21 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-12-01 13:53 JM [this message]
-- strict thread matches above, loose matches on Subject: below --
2008-05-05 19:49 Acer Aspire 9813WKMI fan runs all the time after suspend to ram JM
2008-05-06 14:51 ` Thomas Renninger
2008-05-06 18:05 ` Carlos Corbacho
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=17761706.1196517226756.JavaMail.apache@eni-cpps11.sth.basefarm.net \
--to=v-j-m@suomi24.fi \
--cc=linux-acpi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox