Re: CALL FOR TESTING

[Al <al-PoJXY7Eze0c@public.gmane.org>]

[-- Attachment #1.1: Type: text/plain, Size: 797 bytes --]

Cosi' scrisse "Grover, Andrew" <andrew.grover-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>:

> I wanted to make a special request for testing of the 2.4 patch (or
> should I say, MEGA-patch).

Here we are.

> The main issues of importance are:
> 
> - DOES IT BOOT?
> - DOES IT ASSIGN INTERRUPTS PROPERLY?

It works for me. Mainboard is an ABIT KR7A, everything seems to run ok.

mater:~# uname -a
Linux mater 2.4.20-pre7-acpi #1 gio set 19 08:53:33 CEST 2002 i686 unknown

Attached: lspci; dmesg (relevant part).


Regards,


        Luca Amigoni


-- 

If you wrap the Internet around every person on the planet and spin the
planet, software flows in the network. [...] The resistance of the net-
work is directly proportional to the field strength of the intellectual
property system. (Eben Moglen)

[-- Attachment #1.2: lspci --]
[-- Type: text/plain, Size: 7556 bytes --]

00:00.0 Host bridge: VIA Technologies, Inc. VT8367 [KT266]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 0
	Region 0: Memory at c0000000 (32-bit, prefetchable) [size=256M]
	Capabilities: [a0] AGP version 2.0
		Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
		Command: RQ=0 SBA+ AGP+ 64bit- FW- Rate=<none>
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:01.0 PCI bridge: VIA Technologies, Inc. VT8367 [KT266 AGP] (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	Memory behind bridge: d2000000-d4ffffff
	Prefetchable memory behind bridge: d0000000-d1ffffff
	BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 04)
	Subsystem: Creative Labs CT4620 SBLive!
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (500ns min, 5000ns max)
	Interrupt: pin A routed to IRQ 12
	Region 0: I/O ports at d000 [size=32]
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0b.1 Input device controller: Creative Labs SB Live! (rev 01)
	Subsystem: Creative Labs Gameport Joystick
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32
	Region 0: I/O ports at d400 [size=8]
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 10)
	Subsystem: Realtek Semiconductor Co., Ltd. RT8139
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (8000ns min, 16000ns max)
	Interrupt: pin A routed to IRQ 11
	Region 0: I/O ports at d800 [size=256]
	Region 1: Memory at d6001000 (32-bit, non-prefetchable) [size=256]

00:0f.0 SCSI storage controller: Adaptec 7892A (rev 02)
	Subsystem: Adaptec: Unknown device 62a0
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (10000ns min, 6250ns max), cache line size 08
	Interrupt: pin A routed to IRQ 11
	BIST result: 00
	Region 0: I/O ports at dc00 [disabled] [size=256]
	Region 1: Memory at d6000000 (64-bit, non-prefetchable) [size=4K]
	Expansion ROM at <unassigned> [disabled] [size=128K]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
	Subsystem: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
	Subsystem: VIA Technologies, Inc. Bus Master IDE
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32
	Interrupt: pin A routed to IRQ 10
	Region 4: I/O ports at e000 [size=16]
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 1b) (prog-if 00 [UHCI])
	Subsystem: Unknown device 0925:1234
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, cache line size 08
	Interrupt: pin D routed to IRQ 12
	Region 4: I/O ports at e400 [size=32]
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 1b) (prog-if 00 [UHCI])
	Subsystem: Unknown device 0925:1234
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, cache line size 08
	Interrupt: pin D routed to IRQ 12
	Region 4: I/O ports at e800 [size=32]
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.4 USB Controller: VIA Technologies, Inc. UHCI USB (rev 1b) (prog-if 00 [UHCI])
	Subsystem: Unknown device 0925:1234
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, cache line size 08
	Interrupt: pin D routed to IRQ 12
	Region 4: I/O ports at ec00 [size=32]
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 82) (prog-if 00 [VGA])
	Subsystem: Matrox Graphics, Inc. Millennium G450 Dual Head LX
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (4000ns min, 8000ns max), cache line size 08
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at d0000000 (32-bit, prefetchable) [size=32M]
	Region 1: Memory at d2000000 (32-bit, non-prefetchable) [size=16K]
	Region 2: Memory at d3000000 (32-bit, non-prefetchable) [size=8M]
	Expansion ROM at <unassigned> [disabled] [size=128K]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [f0] AGP version 2.0
		Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
		Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=<none>


[-- Attachment #1.3: dmesg --]
[-- Type: text/plain, Size: 4711 bytes --]

Linux version 2.4.20-pre7-acpi (root@mater) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 gio set 19 08:53:33 CEST 2002
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
 BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
 BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 VIA694                     ) @ 0x000f6e00
ACPI: RSDT (v001 VIA694 AWRDACPI 16944.11825) @ 0x1fff3000
ACPI: FADT (v001 VIA694 AWRDACPI 16944.11825) @ 0x1fff3040
ACPI: DSDT (v001 VIA694 AWRDACPI 00000.04096) @ 0x00000000
ACPI: BIOS passes blacklist
ACPI: MADT not present
Kernel command line: BOOT_IMAGE=acpi ro root=805 video=matrox:vesa:0x1B8
Found and enabled local APIC!
Initializing CPU#0
Detected 1467.319 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2929.45 BogoMIPS
Memory: 515516k/524224k available (1604k kernel code, 8324k reserved, 510k data, 276k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Before vendor init, caps: 0383fbff c1cbfbff 00000000, vendor = 2
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0383fbff c1cbfbff 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU:     After generic, caps: 0383fbff c1cbfbff 00000000 00000000
CPU:             Common caps: 0383fbff c1cbfbff 00000000 00000000
CPU: AMD Athlon(tm) XP 1700+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1467.3383 MHz.
..... host bus clock speed is 266.7888 MHz.
cpu: 0, clocks: 2667888, slice: 1333944
CPU0<T0:2667888,T1:1333936,D:8,S:1333944,C:2667888>
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20020918
PCI: PCI BIOS revision 2.10 entry at 0xfb4d0, last bus=1
PCI: Using configuration type 1
 tbxface-0099 [03] Acpi_load_tables      : ACPI Tables successfully loaded
Parsing Methods:................................................................................................
Table [DSDT] - 383 Objects with 31 Devices 96 Methods 22 Regions
ACPI Namespace successfully loaded at root c036ea1c
evxfevnt-0074 [04] Acpi_enable           : Transition to ACPI mode successful
Executing all Device _STA and_INI methods:...............................
31 Devices found containing: 31 _STA, 2 _INI methods
Completing Region/Field/Buffer/Package initialization:.....................................................
Initialized 18/22 Regions 6/8 Fields 16/17 Buffers 13/13 Packages (383 nodes)
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
pci_bind-0194 [05] acpi_pci_bind         : Device 00:00:12.00 not present in PCI namespace
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 12 14 15, disabled)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
PCI: Probing PCI hardware
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
ACPI: Fan [FAN] (on)
ACPI: Processor [CPU0] (supports C1 C2, 2 throttling states)
ACPI: Thermal Zone [THRM] (51 C)

[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]