Tecra S1 ACPI

Tecra S1 ACPI

[Marek Wawrzyczny]

[-- Attachment #1: Type: text/plain, Size: 2261 bytes --]

Hi all,

This may be ambitious but I am trying to get ACPI working on a Tecra S1 Gentoo 
2.6.6 system.
I have applied the acpi-2.6.6... patch and a initrd patch, and tried a variety 
of "fixed" DSDTs and not using a custom DSDT. I always get the boot messages 
shown below. I have also attached the DSDT.
Help would be greatly appreciated.





ACPI: Subsystem revision 20040326
ACPI: IRQ9 SCI: Edge set to Level Trigger.
    ACPI-1133: *** Error: Method execution failed [\_SB_.PCI0.PCI2.DOCK._STA] 
(Node c16e791c), AE_NOT_EXIST
    ACPI-0154: *** Error: Method execution failed [\_SB_.PCI0.PCI2.DOCK._STA] 
(Node c16e791c), AE_NOT_EXIST
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
    ACPI-1133: *** Error: Method execution failed [\_SB_.BAT0._STA] (Node 
c16e8e9c), AE_NOT_EXIST
    ACPI-1133: *** Error: Method execution failed [\_SB_.BAT1._STA] (Node 
c16e8d5c), AE_NOT_EXIST
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2._PRT]
    ACPI-1133: *** Error: Method execution failed [\_SB_.PCI0.PCI2.DOCK._STA] 
(Node c16e791c), AE_NOT_EXIST
ACPI: PCI Interrupt Link [LNKA] (IRQs *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs *6)
ACPI: PCI Interrupt Link [LNKF] (IRQs 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 11) *0, disabled.
ACPI: Embedded Controller [EC0] (gpe 16)
ACPI: Power Resource [PFA1] (off)
ACPI: Power Resource [PFA0] (off)
SCSI subsystem initialized
Linux Kernel Card Services
  options:  [pci] [cardbus] [pm]
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 6
PCI: Using ACPI for IRQ routing



[-- Attachment #2: dsdt.dsl.tar.bz2 --]
[-- Type: application/x-tbz, Size: 10605 bytes --]

Re: Tecra S1 ACPI

[Marek Wawrzyczny]

Apologies.

I have searched for answers extensively before but have just now found 
references to ECDT which apparently is missing on Tecra S1. I will attempt to 
find the right kernel patches and see if that works.

Btw, is there a single good reference site for these kind of problems?

Cheers,
Marek Wawrzyczny 

On Wed, 16 Jun 2004 18:03, Marek Wawrzyczny wrote:
> Hi all,
>
> This may be ambitious but I am trying to get ACPI working on a Tecra S1
> Gentoo 2.6.6 system.
> I have applied the acpi-2.6.6... patch and a initrd patch, and tried a
> variety of "fixed" DSDTs and not using a custom DSDT. I always get the boot
> messages shown below. I have also attached the DSDT.
> Help would be greatly appreciated.


-------------------------------------------------------
This SF.Net email is sponsored by The 2004 JavaOne(SM) Conference
Learn from the experts at JavaOne(SM), Sun's Worldwide Java Developer
Conference, June 28 - July 1 at the Moscone Center in San Francisco, CA
REGISTER AND SAVE! http://java.sun.com/javaone/sf Priority Code NWMGYKND

Re: Tecra S1 ACPI

[Roderich Schupp]

> This may be ambitious but I am trying to get ACPI working on a Tecra
S1 Gentoo 

Try the patch attached to
http://bugzilla.kernel.org/show_bug.cgi?id=1690
It sorta worked for my Tecra S1, i.e. the error message goes away
and I get the battery status. Suspend-to-ram (S3) still
doesn't work even with kernel 2.6.7, but that's probably not
an ACPI problem.

Cheers, Roderich


-------------------------------------------------------
This SF.Net email is sponsored by The 2004 JavaOne(SM) Conference
Learn from the experts at JavaOne(SM), Sun's Worldwide Java Developer
Conference, June 28 - July 1 at the Moscone Center in San Francisco, CA
REGISTER AND SAVE! http://java.sun.com/javaone/sf Priority Code NWMGYKND

Re: Tecra S1 ACPI

[Savio Lau]

The patch Roderich described works.  It works even better than the 
custom DSDT that have been posted.

However, I did noticed that there is an error with PFA_0  AE "ON" 
instance failing if the computer starts at a warm/hot temperature.

As for suspend - I have user reports that S4 works for them using 
PM_Disk.  S3 still very iffy at ths point.

Cheers,
Savio

Roderich Schupp wrote:

>>This may be ambitious but I am trying to get ACPI working on a Tecra
>>    
>>
>S1 Gentoo 
>
>Try the patch attached to
>http://bugzilla.kernel.org/show_bug.cgi?id=1690
>It sorta worked for my Tecra S1, i.e. the error message goes away
>and I get the battery status. Suspend-to-ram (S3) still
>doesn't work even with kernel 2.6.7, but that's probably not
>an ACPI problem.
>
>Cheers, Roderich
>
>
>-------------------------------------------------------
>This SF.Net email is sponsored by The 2004 JavaOne(SM) Conference
>Learn from the experts at JavaOne(SM), Sun's Worldwide Java Developer
>Conference, June 28 - July 1 at the Moscone Center in San Francisco, CA
>REGISTER AND SAVE! http://java.sun.com/javaone/sf Priority Code NWMGYKND
>_______________________________________________
>Acpi-devel mailing list
>Acpi-devel-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org
>https://lists.sourceforge.net/lists/listinfo/acpi-devel
>
>
>  
>


-------------------------------------------------------
This SF.Net email is sponsored by The 2004 JavaOne(SM) Conference
Learn from the experts at JavaOne(SM), Sun's Worldwide Java Developer
Conference, June 28 - July 1 at the Moscone Center in San Francisco, CA
REGISTER AND SAVE! http://java.sun.com/javaone/sf Priority Code NWMGYKND