Re: [nico-kernel-xuaVFQXs+5hIG4jRRZ66WA@public.gmane.org: [BUG] pdc202xx_new and ACPI fails]

[Nico Schottelius <nico-kernel-xuaVFQXs+5hIG4jRRZ66WA@public.gmane.org>]

[-- Attachment #1: Type: text/plain, Size: 3730 bytes --]

Sorry for breaking References, should I only answer bugme-daemon?
(I never used bugzilla before, sorry)

I tried the patch, but it does not apply:

------------< snip >----------------

eiche# patch --dry-run < ../patch-acpi 
can't find file to patch at input line 15
Perhaps you should have used the -p or --strip option?
The text leading up to this was:
--------------------------
|http://bugme.osdl.org/show_bug.cgi?id=3876
|
|
|
|
|
|------- Additional Comments From shaohua.li-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org  2004-12-06 18:07 -------
|Looks like ACPI is doing the right thing. Per PCI spec, add-in card get 
|derived IRQ from its parent. In your system, the BIOS tells us IDE 3 get 19 
|and IDE 5 get 16. I'd like know the dmesg output after apply the below debug 
|code. Thanks.
|
|--- drivers/acpi/pci_irq.c.orig      2004-12-07 09:56:36.604609696 +0800
|+++ drivers/acpi/pci_irq.c   2004-12-07 09:58:16.857368960 +0800
--------------------------
File to patch: drivers/acpi/pci_irq.c
patching file drivers/acpi/pci_irq.c
patch: **** malformed patch at line 18: &edge_level, &active_high_low);

------------< snap >----------------

(Perhaps because I am too tired)

Anyway inserting the code into drivers/acpi/pci_irq.c manually at
line 370 works.

Here is the relevant part of dmesg:


------------< snip >----------------

apm: BIOS not found.
PDC20270: IDE controller at PCI slot 0000:02:01.0
ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 19 (level, low) -> IRQ 19
PDC20270: chipset revision 2
PDC20270: ROM enabled at 0xdfee0000
PDC20270: 100% native mode on irq 19
    ide2: BM-DMA at 0xbc00-0xbc07, BIOS settings: hde:pio, hdf:pio
    ide3: BM-DMA at 0xbc08-0xbc0f, BIOS settings: hdg:pio, hdh:pio
ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 16 (level, low) -> IRQ 16
    ide4: BM-DMA at 0xa800-0xa807, BIOS settings: hdi:pio, hdj:pio
    ide5: BM-DMA at 0xa808-0xa80f, BIOS settings: hdk:pio, hdl:pio
Probing IDE interface ide2...
Probing IDE interface ide3...
hdh: IDE DVD-ROM 16X, ATAPI CD/DVD-ROM drive
ide3 at 0xc400-0xc407,0xc002 on irq 19
Probing IDE interface ide4...
hdj: TOSHIBA MK4025GAS, ATA DISK drive
Warning: Primary channel requires an 80-pin cable for operation.
hdj reduced to Ultra33 mode.
ide4 at 0xb800-0xb807,0xb402 on irq 16
hdj: max request size: 128KiB
irq 19: nobody cared!
 [<c0130ca4>] __report_bad_irq+0x24/0x80
 [<c0130d81>] note_interrupt+0x61/0xa0
 [<c01307e3>] __do_IRQ+0x113/0x130
 [<c0105119>] do_IRQ+0x19/0x30
 [<c0103916>] common_interrupt+0x1a/0x20
 [<c0101030>] default_idle+0x0/0x30
 [<c0101053>] default_idle+0x23/0x30
 [<c01010ca>] cpu_idle+0x3a/0x60
 [<c03da77f>] start_kernel+0x12f/0x150
 [<c03da3a0>] unknown_bootoption+0x0/0x1a0
handlers:
[<c0294b20>] (ide_intr+0x0/0x170)
Disabling IRQ #19

------------< snap >----------------

> +       if (!irq) {
> +               printk("LSH-TEST:" "PCI interrupt %s[%c]: no GSI",
> +                       pci_name(dev), ('A' + pin));
> +               printk("LSH-TEST:BIOS assign IRQ %d\n", dev->irq);
> +       }

Hrm, this code block you sent me should printout something,
shouldn't it?

I just verified that I booted the correct kernel and foolproofed
tested the output:

eiche# dmesg| grep LSH
eiche# 

Did I do something wrong?

Have a look at http://schotteli.us/~nico/bug.acpi/dmesg.2.6.10-rc3-LSH-TEST-patch
for full dmesg and at 
http://schotteli.us/~nico/bug.acpi/handpatched-pci_irq.c

for the source file I created with manually patching.

Nico

-- 
Keep it simple & stupid, use what's available.
Please use pgp encryption: 8D0E 27A4 is my id.
http://nico.schotteli.us | http://linux.schottelius.org

[-- Attachment #2: Type: application/pgp-signature, Size: 827 bytes --]