* Re: 2.6.20-rc6-mm3 [not found] ` <45BFC442.5000903@gmail.com> @ 2007-01-30 22:27 ` Andrew Morton 2007-01-31 0:55 ` 2.6.20-rc6-mm3 Karsten Wiese 2007-01-31 11:54 ` 2.6.20-rc6-mm3 Maciej Rutecki [not found] ` <45BFEDFB.6000500@imap.cc> 1 sibling, 2 replies; 19+ messages in thread From: Andrew Morton @ 2007-01-30 22:27 UTC (permalink / raw) To: Maciej Rutecki; +Cc: linux-kernel, linux-acpi On Tue, 30 Jan 2007 23:18:42 +0100 Maciej Rutecki <maciej.rutecki@gmail.com> wrote: > Andrew Morton napisa__(a): > > Temporarily at > > > > http://userweb.kernel.org/~akpm/2.6.20-rc6-mm3/ > > > > Will appear later at > > > > ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.20-rc6/2.6.20-rc6-mm3/ > > > > > > - Restored git-block.patch: mainly the block unplugging rework. The > > problematic CFQ updates have been taken out. > > > > - Restored the fsaio patches as a consequence. > > > > - A huge ACPI update. > > I have two problems. First suspend to disk. > > After suspend to disk (before resume) I check time in bios, and it's > correct, but during resume, I have this message: > > "Suspending console(s)" > > system wait 20 seconds (or more) until finish resume. Also system clock > was slow about this 20 seconds. OK, thanks. That might be due to the time-management updates as well. I'll see if I can reproduce this. If you're keen, you could test just 2.6.19-rc6+origin.patch+git-acpi.patch from ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.20-rc6/2.6.20-rc6-mm3/broken-out and see which of these problems remain. > Second problem, power button doesn't work. When I pressed it, I has this > error: > > ACPI Error (evevent-0305): No installed handler for fixed event > [00000002] [20070126] That sounds like an acpi regression, yup. ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: 2.6.20-rc6-mm3 2007-01-30 22:27 ` 2.6.20-rc6-mm3 Andrew Morton @ 2007-01-31 0:55 ` Karsten Wiese 2007-01-31 13:22 ` 2.6.20-rc6-mm3 Ingo Molnar 2007-02-01 13:03 ` [PATCH -mm] gtod persistent clock resume fix Thomas Gleixner 2007-01-31 11:54 ` 2.6.20-rc6-mm3 Maciej Rutecki 1 sibling, 2 replies; 19+ messages in thread From: Karsten Wiese @ 2007-01-31 0:55 UTC (permalink / raw) To: Andrew Morton; +Cc: Maciej Rutecki, linux-kernel, linux-acpi Am Dienstag, 30. Januar 2007 23:27 schrieb Andrew Morton: > On Tue, 30 Jan 2007 23:18:42 +0100 > Maciej Rutecki <maciej.rutecki@gmail.com> wrote: <...> > > I have two problems. First suspend to disk. > > > > After suspend to disk (before resume) I check time in bios, and it's > > correct, but during resume, I have this message: > > > > "Suspending console(s)" > > > > system wait 20 seconds (or more) until finish resume. Also system clock > > was slow about this 20 seconds. > > OK, thanks. That might be due to the time-management updates as well. > I'll see if I can reproduce this. > > If you're keen, you could test just 2.6.19-rc6+origin.patch+git-acpi.patch > from > ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.20-rc6/2.6.20-rc6-mm3/broken-out > and see which of these problems remain. Similar weirdness here on rc6-mm2 and rc6-rt*: resume from disk waits unduly long. I played with bios clock setting after I wondered why susp/res wouldn't work overnight: the longer the (faked/real) suspend to disk time, the longer the (not seen on 2.6.18-rt) waiting past the incrementing % display, before things are running again. After turning time backwards in bios, console mouse handler gpm experiences "interrupted system call". Some waiting times from rc6-rt6 from memory: Config | HZ | NO_HZ + HRESTIMERS cmos clock unchanged | 2s | 6s cmos clock += 10min | | 2 minutes cmos clock += 2 month | 20s | > 4minutes, test interrupted Karsten ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: 2.6.20-rc6-mm3 2007-01-31 0:55 ` 2.6.20-rc6-mm3 Karsten Wiese @ 2007-01-31 13:22 ` Ingo Molnar 2007-01-31 14:25 ` 2.6.20-rc6-mm3 Karsten Wiese 2007-02-01 13:03 ` [PATCH -mm] gtod persistent clock resume fix Thomas Gleixner 1 sibling, 1 reply; 19+ messages in thread From: Ingo Molnar @ 2007-01-31 13:22 UTC (permalink / raw) To: Karsten Wiese; +Cc: Andrew Morton, Maciej Rutecki, linux-kernel, linux-acpi * Karsten Wiese <fzu@wemgehoertderstaat.de> wrote: > Similar weirdness here on rc6-mm2 and rc6-rt*: resume from disk waits > unduly long. i'm wondering whether the jiffies update fix from Thomas fixes this bug for you. If not then do you have a serial console enabled? > Some waiting times from rc6-rt6 from memory: > > Config | HZ | NO_HZ + HRESTIMERS > cmos clock unchanged | 2s | 6s > cmos clock += 10min | | 2 minutes > cmos clock += 2 month | 20s | > 4minutes, test interrupted i've seen something like this on -rt (and incorrectly attributed it to -rt) when running on a system which has a serial port and which has a kernel console on that serial port. What happens is that after resume (and straight after console suspend) every serial character printed takes /alot/ of time - and resume does print a number of kernel messages to the console. I didnt get any further in debugging this though, but disabling the serial console made the problem go away. a possibly related thing: the serial code is sensitive to jiffies updates and timers, i saw that during early revisions of the dynticks code - but the specifics escape me. the slowdown could also be something like the kernel somehow wrapping around jiffies and thus doing /alot/ of jiffy ticks? Or it could be a miscalculation in the amount of jiffies that need updating, resulting in a similar number of loops in the jiffy update code. (i'll try to figure out this regression - but wanted to describe to you the known things so far, maybe you'll figure it out faster than me.) Ingo ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: 2.6.20-rc6-mm3 2007-01-31 13:22 ` 2.6.20-rc6-mm3 Ingo Molnar @ 2007-01-31 14:25 ` Karsten Wiese 2007-02-01 8:01 ` 2.6.20-rc6-mm3 Ingo Molnar 0 siblings, 1 reply; 19+ messages in thread From: Karsten Wiese @ 2007-01-31 14:25 UTC (permalink / raw) To: Ingo Molnar; +Cc: Andrew Morton, Maciej Rutecki, linux-kernel, linux-acpi Am Mittwoch, 31. Januar 2007 14:22 schrieb Ingo Molnar: > > * Karsten Wiese <fzu@wemgehoertderstaat.de> wrote: > > > Similar weirdness here on rc6-mm2 and rc6-rt*: resume from disk waits > > unduly long. > > i'm wondering whether the jiffies update fix from Thomas fixes this bug > for you. > > If not then do you have a serial console enabled? > > > Some waiting times from rc6-rt6 from memory: > > > > Config | HZ | NO_HZ + HRESTIMERS > > cmos clock unchanged | 2s | 6s > > cmos clock += 10min | | 2 minutes > > cmos clock += 2 month | 20s | > 4minutes, test interrupted > > i've seen something like this on -rt (and incorrectly attributed it to > -rt) when running on a system which has a serial port and which has a > kernel console on that serial port. What happens is that after resume > (and straight after console suspend) every serial character printed > takes /alot/ of time - and resume does print a number of kernel messages > to the console. I didnt get any further in debugging this though, but > disabling the serial console made the problem go away. > > a possibly related thing: the serial code is sensitive to jiffies > updates and timers, i saw that during early revisions of the dynticks > code - but the specifics escape me. > > the slowdown could also be something like the kernel somehow wrapping > around jiffies and thus doing /alot/ of jiffy ticks? Or it could be a > miscalculation in the amount of jiffies that need updating, resulting in > a similar number of loops in the jiffy update code. > > (i'll try to figure out this regression - but wanted to describe to you > the known things so far, maybe you'll figure it out faster than me.) Serial port console is off here and the jiffies update fix doesn't make a noticeable difference. I've just captured a dmesglog of 3 suspend/resume cycles with printk timestamps. Config has NO_HZ and HRESTIMERS. In the 1st 2 cycles, while in bios, I advanced the cmos clock by ~4minutes, In the last cycle by ~2minutes. After the lapic resume on CPU#0 entries there are roughly proportional timestamp differences of ~60s, ~60s and ~35s. Those equal the unexpected wait times. Will look into what happens between "lapic resume on CPU#0" and "pci 0000:00:00.0: EARLY resume" next. Karsten [ 0.000000] Linux version 2.6.20-rc6-rt6.dbg (ka@a64.localdomain) (gcc-Version 4.1.1 20070105 (Red Hat 4.1.1-51)) #3 PREEMPT Wed Jan 31 14:25:07 CET 2007 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] sanitize start [ 0.000000] sanitize end [ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1 [ 0.000000] copy_e820_map() type is E820_RAM [ 0.000000] copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2 [ 0.000000] copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end: 0000000000100000 type: 2 [ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000003fef0000 end: 000000003fff0000 type: 1 [ 0.000000] copy_e820_map() type is E820_RAM [ 0.000000] copy_e820_map() start: 000000003fff0000 size: 0000000000008000 end: 000000003fff8000 type: 3 [ 0.000000] copy_e820_map() start: 000000003fff8000 size: 0000000000008000 end: 0000000040000000 type: 4 [ 0.000000] copy_e820_map() start: 00000000fec00000 size: 0000000000001000 end: 00000000fec01000 type: 2 [ 0.000000] copy_e820_map() start: 00000000fee00000 size: 0000000000001000 end: 00000000fee01000 type: 2 [ 0.000000] copy_e820_map() start: 00000000fff80000 size: 0000000000080000 end: 0000000100000000 type: 2 [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003fff0000 (usable) [ 0.000000] BIOS-e820: 000000003fff0000 - 000000003fff8000 (ACPI data) [ 0.000000] BIOS-e820: 000000003fff8000 - 0000000040000000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) [ 0.000000] 127MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] found SMP MP-table at 000fbfc0 [ 0.000000] Entering add_active_range(0, 0, 262128) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 262128 [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 262128 [ 0.000000] On node 0 totalpages: 262128 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 255 pages used for memmap [ 0.000000] HighMem zone: 32497 pages, LIFO batch:7 [ 0.000000] DMI 2.3 present. [ 0.000000] ACPI: RSDP (v000 AMI ) @ 0x000fa3c0 [ 0.000000] ACPI: RSDT (v001 AMIINT VIA_K8 0x00000010 MSFT 0x00000097) @ 0x3fff0000 [ 0.000000] ACPI: FADT (v001 AMIINT VIA_K8 0x00000011 MSFT 0x00000097) @ 0x3fff0030 [ 0.000000] ACPI: MADT (v001 AMIINT VIA_K8 0x00000009 MSFT 0x00000097) @ 0x3fff00c0 [ 0.000000] ACPI: DSDT (v001 VIA VIA_K8 0x00001000 MSFT 0x0100000d) @ 0x00000000 [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] Processor #0 15:15 APIC version 16 [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000) [ 0.000000] Detected 2000.346 MHz processor. [ 22.477053] Real-Time Preemption Support (C) 2004-2007 Ingo Molnar [ 22.477060] Built 1 zonelists. Total pages: 260081 [ 22.477146] Kernel command line: ro root=LABEL=/ agp=off selinux=off 1 [ 22.477412] mapped APIC to ffffd000 (fee00000) [ 22.477416] mapped IOAPIC to ffffc000 (fec00000) [ 22.477421] Enabling fast FPU save and restore... done. [ 22.477425] Enabling unmasked SIMD FPU exception support... done. [ 22.477434] Initializing CPU#0 [ 22.477439] WARNING: experimental RCU implementation. [ 22.477502] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 22.479554] Console: colour VGA+ 80x25 [ 22.485288] num_possible_cpus(): 1 [ 22.486711] CPU#0: allocated 2097152 bytes trace buffer. [ 22.488149] CPU#0: allocated 2097152 bytes max-trace buffer. [ 22.489599] allocated 2097152 bytes out-trace buffer. [ 22.489712] tracer: a total of 6291456 bytes allocated. [ 22.489823] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 22.489989] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 22.490099] ... MAX_LOCK_DEPTH: 30 [ 22.490210] ... MAX_LOCKDEP_KEYS: 2048 [ 22.490320] ... CLASSHASH_SIZE: 1024 [ 22.490429] ... MAX_LOCKDEP_ENTRIES: 8192 [ 22.490539] ... MAX_LOCKDEP_CHAINS: 16384 [ 22.490648] ... CHAINHASH_SIZE: 8192 [ 22.490757] memory used by lock dependency info: 1096 kB [ 22.490868] per task-struct memory footprint: 1200 bytes [ 22.491291] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 22.491835] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 22.521443] Memory: 1024840k/1048512k available (2187k kernel code, 22908k reserved, 1039k data, 200k init, 131008k highmem) [ 22.521627] virtual kernel memory layout: [ 22.521629] fixmap : 0xfffaa000 - 0xfffff000 ( 340 kB) [ 22.521632] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 22.521634] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 22.521637] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 22.521639] .init : 0xc042a000 - 0xc045c000 ( 200 kB) [ 22.521642] .data : 0xc0322f25 - 0xc0426d34 (1039 kB) [ 22.521644] .text : 0xc0100000 - 0xc0322f25 (2187 kB) [ 22.522511] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 22.602851] Calibrating delay using timer specific routine.. 4005.80 BogoMIPS (lpj=8011611) [ 22.603165] Security Framework v1.0.0 initialized [ 22.603279] Capability LSM initialized [ 22.603386] Failure registering Root Plug module with the kernel [ 22.603501] Failure registering Root Plug module with primary security module. [ 22.603700] Mount-cache hash table entries: 512 [ 22.604173] CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000000 00000000 00000000 [ 22.604191] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 22.604308] CPU: L2 Cache: 512K (64 bytes/line) [ 22.604419] CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000000 00000000 00000000 [ 22.604435] Intel machine check architecture supported. [ 22.604547] Intel machine check reporting enabled on CPU#0. [ 22.604667] CPU: AMD Athlon(tm) 64 Processor 3200+ stepping 00 [ 22.604880] Checking 'hlt' instruction... OK. [ 22.618969] ACPI: Core revision 20060707 [ 22.625743] ENABLING IO-APIC IRQs [ 22.626171] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0 [ 22.879023] NET: Registered protocol family 16 [ 22.879415] ACPI: bus type pci registered [ 22.880276] PCI: PCI BIOS revision 2.10 entry at 0xfdae1, last bus=1 [ 22.880389] PCI: Using configuration type 1 [ 22.880498] Setting up standard PCI resources [ 22.900250] ACPI: Interpreter enabled [ 22.900362] ACPI: Using IOAPIC for interrupt routing [ 22.901486] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 22.901607] PCI: Probing PCI hardware (bus 00) [ 22.903444] PCI: MSI-K8T-Neo2Fir, attempting to turn soundcard ON [ 22.903560] PCI: MSI-K8T-Neo2Fir, soundcard on [ 22.904032] Boot video device is 0000:01:00.0 [ 22.904104] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 22.966889] ACPI: Power Resource [URP1] (off) [ 22.967146] ACPI: Power Resource [URP2] (off) [ 22.967402] ACPI: Power Resource [FDDP] (off) [ 22.967659] ACPI: Power Resource [LPTP] (off) [ 22.972136] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 22.973387] ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 10 11 12 14 15) [ 22.974680] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15) [ 22.975916] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 12 14 15) [ 22.977195] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 22.978646] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 22.980038] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 22.981427] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 22.982719] Linux Plug and Play Support v0.97 (c) Adam Belay [ 22.982852] pnp: PnP ACPI init [ 22.989499] pnp: PnP ACPI: found 10 devices [ 22.989854] usbcore: registered new interface driver usbfs [ 22.990050] usbcore: registered new interface driver hub [ 22.990291] usbcore: registered new device driver usb [ 22.990502] PCI: Using ACPI for IRQ routing [ 22.990613] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 22.994622] NetLabel: Initializing [ 22.994728] NetLabel: domain hash size = 128 [ 22.994837] NetLabel: protocols = UNLABELED CIPSOv4 [ 22.994981] NetLabel: unlabeled traffic allowed by default [ 22.996525] PCI: Bridge: 0000:00:01.0 [ 22.996633] IO window: disabled. [ 22.996744] MEM window: cde00000-cfefffff [ 22.996856] PREFETCH window: bdd00000-cdcfffff [ 22.996985] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 22.997039] NET: Registered protocol family 2 [ 23.018195] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 23.018625] TCP established hash table entries: 32768 (order: 9, 2752512 bytes) [ 23.030734] TCP bind hash table entries: 16384 (order: 8, 1310720 bytes) [ 23.036900] TCP: Hash tables configured (established 32768 bind 16384) [ 23.037035] TCP reno registered [ 23.042355] checking if image is initramfs... it is [ 23.136643] Freeing initrd memory: 1256k freed [ 23.137406] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) [ 23.137520] apm: overridden by ACPI. [ 23.138340] audit: initializing netlink socket (disabled) [ 23.138495] audit(1170253668.500:1): initialized [ 23.138842] highmem bounce pool size: 64 pages [ 23.138954] Total HugeTLB memory allocated, 0 [ 23.139322] VFS: Disk quotas dquot_6.5.1 [ 23.139459] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 23.139913] io scheduler noop registered [ 23.140071] io scheduler anticipatory registered [ 23.140229] io scheduler deadline registered [ 23.140407] io scheduler cfq registered (default) [ 23.140706] PCI: Bypassing VIA 8237 APIC De-Assert Message [ 23.140994] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 23.152923] Real Time Clock Driver v1.12ac [ 23.153244] Non-volatile memory driver v1.2 [ 23.153357] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 23.409586] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 23.410579] 00:01: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 23.412600] RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize [ 23.413058] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 23.413176] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 23.413449] VP_IDE: IDE controller at PCI slot 0000:00:0f.0 [ 23.413584] ACPI: PCI Interrupt 0000:00:0f.0[A] -> GSI 20 (level, low) -> IRQ 16 [ 23.413811] VP_IDE: chipset revision 6 [ 23.413918] VP_IDE: not 100% native mode: will probe irqs later [ 23.415129] VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.0 [ 23.415302] ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio [ 23.415575] ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio [ 23.415843] Probing IDE interface ide0... [ 23.828683] hda: SAMSUNG SP2014N, ATA DISK drive [ 24.499610] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 24.499885] Probing IDE interface ide1... [ 25.361806] hdc: TSSTcorpCD/DVDW TS-H552B, ATAPI CD/DVD-ROM drive [ 26.032779] ide1 at 0x170-0x177,0x376 on irq 15 [ 26.033380] hda: max request size: 512KiB [ 26.039066] hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63, UDMA(133) [ 26.039633] hda: cache flushes supported [ 26.039833] hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 > [ 26.094517] usbcore: registered new interface driver libusual [ 26.094687] usbcore: registered new interface driver hiddev [ 26.094873] usbcore: registered new interface driver usbhid [ 26.094987] /home/ka/q/kernel/linux-2.6./20/rc6-rt6-kw/drivers/usb/input/hid-core.c: v2.6:USB HID core driver [ 26.095337] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 26.096013] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 26.096253] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 26.096546] mice: PS/2 mouse device common for all mice [ 26.117810] input: AT Translated Set 2 keyboard as /class/input/input0 [ 26.152373] TCP bic registered [ 26.152479] Initializing XFRM netlink socket [ 26.152616] NET: Registered protocol family 1 [ 26.152731] NET: Registered protocol family 17 [ 26.152856] Using IPI Shortcut mode [ 26.153070] ACPI: (supports S0 S1 S3 S4 S5) [ 26.153551] ***************************************************************************** [ 26.153720] * * [ 26.153889] * REMINDER, the following debugging options are turned on in your .config: * [ 26.154056] * * [ 26.154222] * CONFIG_CRITICAL_PREEMPT_TIMING * [ 26.154389] * CONFIG_CRITICAL_IRQSOFF_TIMING * [ 26.154556] * CONFIG_FUNCTION_TRACE * [ 26.154750] * CONFIG_LOCKDEP * [ 26.154917] * * [ 26.155084] * they may increase runtime overhead and latencies. * [ 26.155253] * * [ 26.155423] ***************************************************************************** [ 26.155736] Freeing unused kernel memory: 200k freed [ 26.155912] Write protecting the kernel read-only data: 766k [ 26.156215] Time: tsc clocksource has been installed. [ 26.302780] logips2pp: Detected unknown logitech mouse model 62 [ 26.430080] USB Universal Host Controller Interface driver v3.0 [ 26.430306] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 17 [ 26.430531] uhci_hcd 0000:00:10.0: UHCI Host Controller [ 26.430870] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1 [ 26.431231] uhci_hcd 0000:00:10.0: irq 17, io base 0x0000dc00 [ 26.431686] usb usb1: configuration #1 chosen from 1 choice [ 26.431965] hub 1-0:1.0: USB hub found [ 26.432100] hub 1-0:1.0: 2 ports detected [ 26.535831] ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 17 [ 26.536050] uhci_hcd 0000:00:10.1: UHCI Host Controller [ 26.536243] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2 [ 26.536429] uhci_hcd 0000:00:10.1: irq 17, io base 0x0000e000 [ 26.536755] usb usb2: configuration #1 chosen from 1 choice [ 26.536928] hub 2-0:1.0: USB hub found [ 26.537047] hub 2-0:1.0: 2 ports detected [ 26.639490] ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 17 [ 26.639711] uhci_hcd 0000:00:10.2: UHCI Host Controller [ 26.639900] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 [ 26.640086] uhci_hcd 0000:00:10.2: irq 17, io base 0x0000e400 [ 26.640432] usb usb3: configuration #1 chosen from 1 choice [ 26.640626] hub 3-0:1.0: USB hub found [ 26.640743] hub 3-0:1.0: 2 ports detected [ 26.655296] Switched to high resolution mode on CPU 0 [ 26.743156] ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 17 [ 26.743379] uhci_hcd 0000:00:10.3: UHCI Host Controller [ 26.743547] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 [ 26.743735] uhci_hcd 0000:00:10.3: irq 17, io base 0x0000e800 [ 26.744088] usb usb4: configuration #1 chosen from 1 choice [ 26.744283] hub 4-0:1.0: USB hub found [ 26.744400] hub 4-0:1.0: 2 ports detected [ 26.813898] input: ImExPS/2 Logitech Explorer Mouse as /class/input/input1 [ 26.848563] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 17 [ 26.848791] ehci_hcd 0000:00:10.4: EHCI Host Controller [ 26.848981] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5 [ 26.849197] ehci_hcd 0000:00:10.4: irq 17, io mem 0xcffffd00 [ 26.849314] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 26.849665] usb usb5: configuration #1 chosen from 1 choice [ 26.849827] hub 5-0:1.0: USB hub found [ 26.849997] hub 5-0:1.0: 8 ports detected [ 27.158838] kjournald starting. Commit interval 5 seconds [ 27.158996] EXT3-fs: mounted filesystem with ordered data mode. [ 35.835033] hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) [ 35.835051] Uniform CD-ROM driver Revision: 3.20 [ 35.861074] r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded [ 35.861104] ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 16 (level, low) -> IRQ 18 [ 35.861291] eth0: RTL8169s/8110s at 0xf8806f00, 00:11:09:d9:97:b2, IRQ 18 [ 35.890001] parport: PnPBIOS parport detected. [ 35.890219] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP] [ 36.157882] nvidia: module license 'NVIDIA' taints kernel. [ 36.409188] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 18 [ 36.409420] NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-9631 Thu Nov 9 17:38:10 PST 2006 [ 36.467844] input: PC Speaker as /class/input/input2 [ 36.985986] ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 19 [ 36.986172] PCI: Setting latency timer of device 0000:00:11.5 to 64 [ 41.535760] floppy0: no floppy controllers found [ 41.562057] lp0: using parport0 (interrupt-driven). [ 41.828480] input: Power Button (FF) as /class/input/input3 [ 41.841452] ACPI: Power Button (FF) [PWRF] [ 41.852224] input: Power Button (CM) as /class/input/input4 [ 41.865199] ACPI: Power Button (CM) [PWRB] [ 41.875937] input: Sleep Button (CM) as /class/input/input5 [ 41.888682] ACPI: Sleep Button (CM) [SLPB] [ 41.901162] No dock devices found. [ 41.912664] ibm_acpi: ec object not found [ 42.520611] EXT3 FS on hda3, internal journal [ 42.644071] kjournald starting. Commit interval 5 seconds [ 42.644272] EXT3 FS on hda5, internal journal [ 42.644280] EXT3-fs: mounted filesystem with ordered data mode. [ 42.647271] kjournald starting. Commit interval 5 seconds [ 42.647418] EXT3 FS on hda2, internal journal [ 42.647425] EXT3-fs: mounted filesystem with ordered data mode. [ 43.274376] Adding 1464836k swap on /dev/hda6. Priority:-1 extents:1 across:1464836k [ 43.686588] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3200+ processors (version 2.00.00) [ 43.690186] powernow-k8: 0 : fid 0x2 (1000 MHz), vid 0x12 [ 43.690190] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x8 [ 43.690195] powernow-k8: 2 : fid 0xc (2000 MHz), vid 0x6 [ 89.323447] Time: acpi_pm clocksource has been installed. [ 89.822999] Clocksource tsc unstable (delta = -250051675 ns) [ 107.147024] Stopping tasks ... done. [ 107.217374] Shrinking memory... \b-\bdone (0 pages freed) [ 107.240775] Freed 0 kbytes in 0.02 seconds (0.00 MB/s) [ 107.240783] Suspending console(s) [ 108.145319] pnp: Device 00:02 disabled. [ 108.145818] pnp: Device 00:01 disabled. [ 108.146724] ACPI: PCI interrupt for device 0000:00:11.5 disabled [ 108.160786] ACPI: PCI interrupt for device 0000:00:10.4 disabled [ 108.176729] ACPI: PCI interrupt for device 0000:00:10.3 disabled [ 108.192712] ACPI: PCI interrupt for device 0000:00:10.2 disabled [ 108.208696] ACPI: PCI interrupt for device 0000:00:10.1 disabled [ 108.224680] ACPI: PCI interrupt for device 0000:00:10.0 disabled [ 108.241268] lapic suspend on CPU#0 [ 108.241274] [<c01040fa>] show_trace_log_lvl+0x35/0x54 [ 108.241289] [<c010477c>] show_trace+0x2c/0x2e [ 108.241299] [<c0104843>] dump_stack+0x29/0x2b [ 108.241309] [<c011015b>] lapic_suspend+0xcf/0xf8 [ 108.241319] [<c026cf0d>] sysdev_suspend+0xad/0x216 [ 108.241331] [<c0271563>] device_power_down+0xb5/0xe2 [ 108.241340] [<c0142e5a>] swsusp_suspend+0x1e/0x6e [ 108.241351] [<c014354a>] pm_suspend_disk+0x97/0x14d [ 108.241361] [<c01422c8>] enter_state+0x58/0x161 [ 108.241371] [<c0142461>] state_store+0x90/0xa5 [ 108.241380] [<c01b3891>] subsys_attr_store+0x33/0x35 [ 108.241392] [<c01b3b74>] sysfs_write_file+0xba/0xdb [ 108.241402] [<c01761b4>] vfs_write+0xce/0x1a6 [ 108.241412] [<c0176815>] sys_write+0x4c/0x70 [ 108.241421] [<c01030d7>] sysenter_past_esp+0x6c/0xad [ 108.241430] ======================= [ 108.241446] swsusp: critical section: [ 108.264597] swsusp: Need to copy 16708 pages [ 57.589976] Intel machine check architecture supported. [ 57.589989] Intel machine check reporting enabled on CPU#0. [ 28.767086] lapic resume on CPU#0 [ 28.767089] [<c01040fa>] show_trace_log_lvl+0x35/0x54 [ 28.767097] [<c010477c>] show_trace+0x2c/0x2e [ 28.767102] [<c0104843>] dump_stack+0x29/0x2b [ 28.767107] [<c01101b8>] lapic_resume+0x34/0x1af [ 28.767113] [<c026ca46>] __sysdev_resume+0x20/0x66 [ 28.767119] [<c026d098>] sysdev_resume+0x22/0x5e [ 28.767124] [<c027187b>] device_power_up+0xd/0x14 [ 28.767129] [<c0142e9d>] swsusp_suspend+0x61/0x6e [ 28.767134] [<c014354a>] pm_suspend_disk+0x97/0x14d [ 28.767140] [<c01422c8>] enter_state+0x58/0x161 [ 28.767144] [<c0142461>] state_store+0x90/0xa5 [ 28.767149] [<c01b3891>] subsys_attr_store+0x33/0x35 [ 28.767155] [<c01b3b74>] sysfs_write_file+0xba/0xdb [ 28.767161] [<c01761b4>] vfs_write+0xce/0x1a6 [ 28.767166] [<c0176815>] sys_write+0x4c/0x70 [ 28.767170] [<c01030d7>] sysenter_past_esp+0x6c/0xad [ 28.767175] ======================= [ 96.970169] pci 0000:00:00.0: EARLY resume [ 96.970173] pci 0000:00:00.1: EARLY resume [ 96.970176] pci 0000:00:00.2: EARLY resume [ 96.970180] pci 0000:00:00.3: EARLY resume [ 96.970183] pci 0000:00:00.4: EARLY resume [ 96.970186] pci 0000:00:00.7: EARLY resume [ 96.970189] pci 0000:00:01.0: EARLY resume [ 96.970192] r8169 0000:00:0b.0: EARLY resume [ 96.970196] VIA_IDE 0000:00:0f.0: EARLY resume [ 96.970199] uhci_hcd 0000:00:10.0: EARLY resume [ 96.970203] uhci_hcd 0000:00:10.1: EARLY resume [ 96.970206] uhci_hcd 0000:00:10.2: EARLY resume [ 96.970209] uhci_hcd 0000:00:10.3: EARLY resume [ 96.970213] ehci_hcd 0000:00:10.4: EARLY resume [ 96.970216] pci 0000:00:11.0: EARLY resume [ 96.970222] PCI: MSI-K8T-Neo2Fir, attempting to turn soundcard ON [ 96.970228] PCI: MSI-K8T-Neo2Fir, soundcard on [ 96.970233] VIA 82xx Audio 0000:00:11.5: EARLY resume [ 96.970236] pci 0000:00:18.0: EARLY resume [ 96.970240] pci 0000:00:18.1: EARLY resume [ 96.970243] pci 0000:00:18.2: EARLY resume [ 96.970246] k8temp 0000:00:18.3: EARLY resume [ 96.970250] nvidia 0000:01:00.0: EARLY resume [ 96.970254] pcspkr pcspkr: EARLY resume [ 96.970257] platform vesafb.0: EARLY resume [ 96.970264] serial8250 serial8250: EARLY resume [ 96.970268] i8042 i8042: EARLY resume [ 96.978026] acpi acpi: resuming [ 96.978035] pci 0000:00:00.0: resuming [ 96.978081] pci 0000:00:00.1: resuming [ 96.978104] pci 0000:00:00.2: resuming [ 96.978126] pci 0000:00:00.3: resuming [ 96.978149] pci 0000:00:00.4: resuming [ 96.978171] pci 0000:00:00.7: resuming [ 96.978194] pci 0000:00:01.0: resuming [ 96.978237] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 96.978242] r8169 0000:00:0b.0: resuming [ 96.978246] VIA_IDE 0000:00:0f.0: resuming [ 96.978293] ACPI: PCI Interrupt 0000:00:0f.0[A] -> GSI 20 (level, low) -> IRQ 16 [ 96.978300] uhci_hcd 0000:00:10.0: resuming [ 96.989807] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 17 [ 96.989862] usb usb1: root hub lost power or was reset [ 96.989875] uhci_hcd 0000:00:10.1: resuming [ 97.005774] ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 17 [ 97.005827] usb usb2: root hub lost power or was reset [ 97.005839] uhci_hcd 0000:00:10.2: resuming [ 97.021742] ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 17 [ 97.021795] usb usb3: root hub lost power or was reset [ 97.021807] uhci_hcd 0000:00:10.3: resuming [ 97.037710] ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 17 [ 97.037763] usb usb4: root hub lost power or was reset [ 97.037776] ehci_hcd 0000:00:10.4: resuming [ 97.053679] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 17 [ 97.053719] usb usb5: root hub lost power or was reset [ 97.053735] pci 0000:00:11.0: resuming [ 97.053770] VIA 82xx Audio 0000:00:11.5: resuming [ 97.069678] ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 19 [ 97.069687] PCI: Setting latency timer of device 0000:00:11.5 to 64 [ 97.072809] pci 0000:00:18.0: resuming [ 97.072825] pci 0000:00:18.1: resuming [ 97.072837] pci 0000:00:18.2: resuming [ 97.072850] k8temp 0000:00:18.3: resuming [ 97.072863] nvidia 0000:01:00.0: resuming [ 97.073007] pnp 00:00: resuming [ 97.073014] serial 00:01: resuming [ 97.074378] pnp: Device 00:01 activated. [ 97.074384] parport_pc 00:02: resuming [ 97.076025] pnp: Device 00:02 activated. [ 97.076029] system 00:03: resuming [ 97.076032] pnp 00:04: resuming [ 97.076034] pnp 00:05: resuming [ 97.076037] pnp 00:06: resuming [ 97.076040] pnp 00:07: resuming [ 97.076043] i8042 aux 00:08: resuming [ 97.076181] pnp: Failed to activate device 00:08. [ 97.076185] i8042 kbd 00:09: resuming [ 97.076199] pnp: Failed to activate device 00:09. [ 97.076208] pcspkr pcspkr: resuming [ 97.076212] platform vesafb.0: resuming [ 97.076250] serial8250 serial8250: resuming [ 97.076257] ide-disk 0.0: resuming [ 97.129427] ide-cdrom 1.0: resuming [ 97.131585] i8042 i8042: resuming [ 97.131618] atkbd serio0: resuming [ 97.164790] psmouse serio1: resuming [ 97.345198] logips2pp: Detected unknown logitech mouse model 62 [ 97.848637] usb usb1: resuming [ 97.888028] hub 1-0:1.0: resuming [ 97.888032] usb usb2: resuming [ 196.047736] hub 2-0:1.0: resuming [ 196.047743] usb usb3: resuming [ 196.087517] hub 3-0:1.0: resuming [ 196.087524] usb usb4: resuming [ 196.127477] hub 4-0:1.0: resuming [ 196.127484] usb usb5: resuming [ 196.159445] hub 5-0:1.0: resuming [ 196.159464] ac97 0-0:ALC850: resuming [ 196.159515] Restarting tasks ... done. [ 286.477196] dbs_check_cpu: t310 < i311 [ 368.901522] uhci_hcd 0000:00:10.3: remove, state 1 [ 368.901534] usb usb4: USB disconnect, address 1 [ 368.905100] uhci_hcd 0000:00:10.3: USB bus 4 deregistered [ 368.906081] ACPI: PCI interrupt for device 0000:00:10.3 disabled [ 368.906109] uhci_hcd 0000:00:10.2: remove, state 1 [ 368.906119] usb usb3: USB disconnect, address 1 [ 368.909638] uhci_hcd 0000:00:10.2: USB bus 3 deregistered [ 368.910592] ACPI: PCI interrupt for device 0000:00:10.2 disabled [ 368.910620] uhci_hcd 0000:00:10.1: remove, state 1 [ 368.910629] usb usb2: USB disconnect, address 1 [ 368.914235] uhci_hcd 0000:00:10.1: USB bus 2 deregistered [ 368.914334] ACPI: PCI interrupt for device 0000:00:10.1 disabled [ 368.914361] uhci_hcd 0000:00:10.0: remove, state 1 [ 368.914369] usb usb1: USB disconnect, address 1 [ 368.915250] uhci_hcd 0000:00:10.0: USB bus 1 deregistered [ 368.915333] ACPI: PCI interrupt for device 0000:00:10.0 disabled [ 416.880815] r8169: eth0: link up [ 227.932433] Stopping tasks ... done. [ 227.933330] Shrinking memory... \b-\bdone (0 pages freed) [ 227.949058] Freed 0 kbytes in 0.01 seconds (0.00 MB/s) [ 227.949063] Suspending console(s) [ 228.840372] pnp: Device 00:02 disabled. [ 228.840626] pnp: Device 00:01 disabled. [ 228.841385] ACPI: PCI interrupt for device 0000:00:11.5 disabled [ 228.854045] ACPI: PCI interrupt for device 0000:00:10.4 disabled [ 228.886441] lapic suspend on CPU#0 [ 228.886445] [<c01040fa>] show_trace_log_lvl+0x35/0x54 [ 228.886453] [<c010477c>] show_trace+0x2c/0x2e [ 228.886458] [<c0104843>] dump_stack+0x29/0x2b [ 228.886463] [<c011015b>] lapic_suspend+0xcf/0xf8 [ 228.886469] [<c026cf0d>] sysdev_suspend+0xad/0x216 [ 228.886474] [<c0271563>] device_power_down+0xb5/0xe2 [ 228.886480] [<c0142e5a>] swsusp_suspend+0x1e/0x6e [ 228.886485] [<c014354a>] pm_suspend_disk+0x97/0x14d [ 228.886490] [<c01422c8>] enter_state+0x58/0x161 [ 228.886495] [<c0142461>] state_store+0x90/0xa5 [ 228.886499] [<c01b3891>] subsys_attr_store+0x33/0x35 [ 228.886505] [<c01b3b74>] sysfs_write_file+0xba/0xdb [ 228.886511] [<c01761b4>] vfs_write+0xce/0x1a6 [ 228.886516] [<c0176815>] sys_write+0x4c/0x70 [ 228.886520] [<c01030d7>] sysenter_past_esp+0x6c/0xad [ 228.886525] ======================= [ 228.886536] swsusp: critical section: [ 228.902253] swsusp: Need to copy 19089 pages [ 28.574318] Intel machine check architecture supported. [ 28.574325] Intel machine check reporting enabled on CPU#0. [ 28.574561] lapic resume on CPU#0 [ 28.574565] [<c01040fa>] show_trace_log_lvl+0x35/0x54 [ 28.574573] [<c010477c>] show_trace+0x2c/0x2e [ 28.574578] [<c0104843>] dump_stack+0x29/0x2b [ 28.574583] [<c01101b8>] lapic_resume+0x34/0x1af [ 28.574589] [<c026ca46>] __sysdev_resume+0x20/0x66 [ 28.574595] [<c026d098>] sysdev_resume+0x22/0x5e [ 28.574600] [<c027187b>] device_power_up+0xd/0x14 [ 28.574605] [<c0142e9d>] swsusp_suspend+0x61/0x6e [ 28.574610] [<c014354a>] pm_suspend_disk+0x97/0x14d [ 28.574615] [<c01422c8>] enter_state+0x58/0x161 [ 28.574620] [<c0142461>] state_store+0x90/0xa5 [ 28.574625] [<c01b3891>] subsys_attr_store+0x33/0x35 [ 28.574631] [<c01b3b74>] sysfs_write_file+0xba/0xdb [ 28.574637] [<c01761b4>] vfs_write+0xce/0x1a6 [ 28.574642] [<c0176815>] sys_write+0x4c/0x70 [ 28.574647] [<c01030d7>] sysenter_past_esp+0x6c/0xad [ 28.574651] ======================= [ 90.251248] pci 0000:00:00.0: EARLY resume [ 90.251252] pci 0000:00:00.1: EARLY resume [ 90.251255] pci 0000:00:00.2: EARLY resume [ 90.251258] pci 0000:00:00.3: EARLY resume [ 90.251261] pci 0000:00:00.4: EARLY resume [ 90.251265] pci 0000:00:00.7: EARLY resume [ 90.251268] pci 0000:00:01.0: EARLY resume [ 90.251271] r8169 0000:00:0b.0: EARLY resume [ 90.251274] VIA_IDE 0000:00:0f.0: EARLY resume [ 90.251278] pci 0000:00:10.0: EARLY resume [ 90.251281] pci 0000:00:10.1: EARLY resume [ 90.251284] pci 0000:00:10.2: EARLY resume [ 90.251287] pci 0000:00:10.3: EARLY resume [ 90.251291] ehci_hcd 0000:00:10.4: EARLY resume [ 90.251294] pci 0000:00:11.0: EARLY resume [ 90.251300] PCI: MSI-K8T-Neo2Fir, attempting to turn soundcard ON [ 90.251306] PCI: MSI-K8T-Neo2Fir, soundcard on [ 90.251311] VIA 82xx Audio 0000:00:11.5: EARLY resume [ 90.251315] pci 0000:00:18.0: EARLY resume [ 90.251318] pci 0000:00:18.1: EARLY resume [ 90.251321] pci 0000:00:18.2: EARLY resume [ 90.251324] k8temp 0000:00:18.3: EARLY resume [ 90.251328] nvidia 0000:01:00.0: EARLY resume [ 90.251332] pcspkr pcspkr: EARLY resume [ 90.251335] platform vesafb.0: EARLY resume [ 90.251342] serial8250 serial8250: EARLY resume [ 90.251346] i8042 i8042: EARLY resume [ 90.259839] acpi acpi: resuming [ 90.259848] pci 0000:00:00.0: resuming [ 90.259899] pci 0000:00:00.1: resuming [ 90.259922] pci 0000:00:00.2: resuming [ 90.259944] pci 0000:00:00.3: resuming [ 90.259967] pci 0000:00:00.4: resuming [ 90.259989] pci 0000:00:00.7: resuming [ 90.260012] pci 0000:00:01.0: resuming [ 90.260054] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 90.260060] r8169 0000:00:0b.0: resuming [ 90.271012] VIA_IDE 0000:00:0f.0: resuming [ 90.271061] ACPI: PCI Interrupt 0000:00:0f.0[A] -> GSI 20 (level, low) -> IRQ 16 [ 90.271067] pci 0000:00:10.0: resuming [ 90.271094] PM: Writing back config space on device 0000:00:10.0 at offset 1 (was 2100017, writing 2100013) [ 90.271107] pci 0000:00:10.1: resuming [ 90.271134] PM: Writing back config space on device 0000:00:10.1 at offset 1 (was 2100017, writing 2100013) [ 90.271147] pci 0000:00:10.2: resuming [ 90.271173] PM: Writing back config space on device 0000:00:10.2 at offset 1 (was 2100017, writing 2100013) [ 90.271186] pci 0000:00:10.3: resuming [ 90.271212] PM: Writing back config space on device 0000:00:10.3 at offset 1 (was 2100017, writing 2100013) [ 90.271225] ehci_hcd 0000:00:10.4: resuming [ 90.286985] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 17 [ 90.287026] usb usb5: root hub lost power or was reset [ 90.287043] pci 0000:00:11.0: resuming [ 90.287078] VIA 82xx Audio 0000:00:11.5: resuming [ 90.302943] ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 19 [ 90.302953] PCI: Setting latency timer of device 0000:00:11.5 to 64 [ 90.306052] pci 0000:00:18.0: resuming [ 90.306068] pci 0000:00:18.1: resuming [ 90.306080] pci 0000:00:18.2: resuming [ 90.306093] k8temp 0000:00:18.3: resuming [ 90.306106] nvidia 0000:01:00.0: resuming [ 90.306245] pnp 00:00: resuming [ 90.306251] serial 00:01: resuming [ 90.307641] pnp: Device 00:01 activated. [ 90.307647] parport_pc 00:02: resuming [ 90.309271] pnp: Device 00:02 activated. [ 90.309275] system 00:03: resuming [ 90.309278] pnp 00:04: resuming [ 90.309281] pnp 00:05: resuming [ 90.309284] pnp 00:06: resuming [ 90.309287] pnp 00:07: resuming [ 90.309290] i8042 aux 00:08: resuming [ 90.309426] pnp: Failed to activate device 00:08. [ 90.309430] i8042 kbd 00:09: resuming [ 90.309445] pnp: Failed to activate device 00:09. [ 90.309454] pcspkr pcspkr: resuming [ 90.309457] platform vesafb.0: resuming [ 90.309496] serial8250 serial8250: resuming [ 90.309503] ide-disk 0.0: resuming [ 90.356307] ide-cdrom 1.0: resuming [ 90.358458] i8042 i8042: resuming [ 90.358491] atkbd serio0: resuming [ 90.391693] psmouse serio1: resuming [ 90.573192] logips2pp: Detected unknown logitech mouse model 62 [ 91.075384] usb usb5: resuming [ 91.105324] hub 5-0:1.0: resuming [ 91.105334] ac97 0-0:ALC850: resuming [ 91.764195] Restarting tasks ... done. [ 184.374518] input: Power Button (FF) as /class/input/input6 [ 184.380803] ACPI: Power Button (FF) [PWRF] [ 184.401383] input: Power Button (CM) as /class/input/input7 [ 184.426364] ACPI: Power Button (CM) [PWRB] [ 184.427403] input: Sleep Button (CM) as /class/input/input8 [ 184.447937] ACPI: Sleep Button (CM) [SLPB] [ 405.243424] Stopping tasks ... done. [ 405.244559] Shrinking memory... \b-\bdone (0 pages freed) [ 405.267891] Freed 0 kbytes in 0.02 seconds (0.00 MB/s) [ 405.267899] Suspending console(s) [ 406.076633] pnp: Device 00:02 disabled. [ 406.077139] pnp: Device 00:01 disabled. [ 406.078087] ACPI: PCI interrupt for device 0000:00:11.5 disabled [ 406.089520] ACPI: PCI interrupt for device 0000:00:10.4 disabled [ 406.121988] lapic suspend on CPU#0 [ 406.121995] [<c01040fa>] show_trace_log_lvl+0x35/0x54 [ 406.122009] [<c010477c>] show_trace+0x2c/0x2e [ 406.122019] [<c0104843>] dump_stack+0x29/0x2b [ 406.122029] [<c011015b>] lapic_suspend+0xcf/0xf8 [ 406.122040] [<c026cf0d>] sysdev_suspend+0xad/0x216 [ 406.122051] [<c0271563>] device_power_down+0xb5/0xe2 [ 406.122060] [<c0142e5a>] swsusp_suspend+0x1e/0x6e [ 406.122071] [<c014354a>] pm_suspend_disk+0x97/0x14d [ 406.122081] [<c01422c8>] enter_state+0x58/0x161 [ 406.122090] [<c0142461>] state_store+0x90/0xa5 [ 406.122099] [<c01b3891>] subsys_attr_store+0x33/0x35 [ 406.122111] [<c01b3b74>] sysfs_write_file+0xba/0xdb [ 406.122121] [<c01761b4>] vfs_write+0xce/0x1a6 [ 406.122131] [<c0176815>] sys_write+0x4c/0x70 [ 406.122140] [<c01030d7>] sysenter_past_esp+0x6c/0xad [ 406.122149] ======================= [ 406.122164] swsusp: critical section: [ 406.145294] swsusp: Need to copy 19231 pages [ 58.244141] Intel machine check architecture supported. [ 58.244155] Intel machine check reporting enabled on CPU#0. [ 29.093849] lapic resume on CPU#0 [ 29.093853] [<c01040fa>] show_trace_log_lvl+0x35/0x54 [ 29.093861] [<c010477c>] show_trace+0x2c/0x2e [ 29.093865] [<c0104843>] dump_stack+0x29/0x2b [ 29.093870] [<c01101b8>] lapic_resume+0x34/0x1af [ 29.093876] [<c026ca46>] __sysdev_resume+0x20/0x66 [ 29.093882] [<c026d098>] sysdev_resume+0x22/0x5e [ 29.093887] [<c027187b>] device_power_up+0xd/0x14 [ 29.093892] [<c0142e9d>] swsusp_suspend+0x61/0x6e [ 29.093897] [<c014354a>] pm_suspend_disk+0x97/0x14d [ 29.093902] [<c01422c8>] enter_state+0x58/0x161 [ 29.093907] [<c0142461>] state_store+0x90/0xa5 [ 29.093912] [<c01b3891>] subsys_attr_store+0x33/0x35 [ 29.093918] [<c01b3b74>] sysfs_write_file+0xba/0xdb [ 29.093923] [<c01761b4>] vfs_write+0xce/0x1a6 [ 29.093928] [<c0176815>] sys_write+0x4c/0x70 [ 29.093933] [<c01030d7>] sysenter_past_esp+0x6c/0xad [ 29.093937] ======================= [ 65.934039] pci 0000:00:00.0: EARLY resume [ 65.934044] pci 0000:00:00.1: EARLY resume [ 65.934047] pci 0000:00:00.2: EARLY resume [ 65.934050] pci 0000:00:00.3: EARLY resume [ 65.934053] pci 0000:00:00.4: EARLY resume [ 65.934056] pci 0000:00:00.7: EARLY resume [ 65.934059] pci 0000:00:01.0: EARLY resume [ 65.934063] r8169 0000:00:0b.0: EARLY resume [ 65.934066] VIA_IDE 0000:00:0f.0: EARLY resume [ 65.934069] pci 0000:00:10.0: EARLY resume [ 65.934073] pci 0000:00:10.1: EARLY resume [ 65.934076] pci 0000:00:10.2: EARLY resume [ 65.934079] pci 0000:00:10.3: EARLY resume [ 65.934082] ehci_hcd 0000:00:10.4: EARLY resume [ 65.934086] pci 0000:00:11.0: EARLY resume [ 65.934091] PCI: MSI-K8T-Neo2Fir, attempting to turn soundcard ON [ 65.934097] PCI: MSI-K8T-Neo2Fir, soundcard on [ 65.934102] VIA 82xx Audio 0000:00:11.5: EARLY resume [ 65.934106] pci 0000:00:18.0: EARLY resume [ 65.934109] pci 0000:00:18.1: EARLY resume [ 65.934112] pci 0000:00:18.2: EARLY resume [ 65.934115] k8temp 0000:00:18.3: EARLY resume [ 65.934119] nvidia 0000:01:00.0: EARLY resume [ 65.934124] pcspkr pcspkr: EARLY resume [ 65.934127] platform vesafb.0: EARLY resume [ 65.934134] serial8250 serial8250: EARLY resume [ 65.934137] i8042 i8042: EARLY resume [ 65.942628] acpi acpi: resuming [ 65.942638] pci 0000:00:00.0: resuming [ 65.942685] pci 0000:00:00.1: resuming [ 65.942708] pci 0000:00:00.2: resuming [ 65.942731] pci 0000:00:00.3: resuming [ 65.942753] pci 0000:00:00.4: resuming [ 65.942776] pci 0000:00:00.7: resuming [ 65.942798] pci 0000:00:01.0: resuming [ 65.942841] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 65.942846] r8169 0000:00:0b.0: resuming [ 65.952005] VIA_IDE 0000:00:0f.0: resuming [ 65.952054] ACPI: PCI Interrupt 0000:00:0f.0[A] -> GSI 20 (level, low) -> IRQ 16 [ 65.952060] pci 0000:00:10.0: resuming [ 65.952087] PM: Writing back config space on device 0000:00:10.0 at offset 1 (was 2100017, writing 2100013) [ 65.952101] pci 0000:00:10.1: resuming [ 65.952127] PM: Writing back config space on device 0000:00:10.1 at offset 1 (was 2100017, writing 2100013) [ 65.952140] pci 0000:00:10.2: resuming [ 65.952166] PM: Writing back config space on device 0000:00:10.2 at offset 1 (was 2100017, writing 2100013) [ 65.952179] pci 0000:00:10.3: resuming [ 65.952206] PM: Writing back config space on device 0000:00:10.3 at offset 1 (was 2100017, writing 2100013) [ 65.952219] ehci_hcd 0000:00:10.4: resuming [ 65.967977] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 17 [ 65.968017] usb usb5: root hub lost power or was reset [ 65.968034] pci 0000:00:11.0: resuming [ 65.968068] VIA 82xx Audio 0000:00:11.5: resuming [ 65.983936] ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 19 [ 65.983945] PCI: Setting latency timer of device 0000:00:11.5 to 64 [ 65.987043] pci 0000:00:18.0: resuming [ 65.987058] pci 0000:00:18.1: resuming [ 65.987071] pci 0000:00:18.2: resuming [ 65.987084] k8temp 0000:00:18.3: resuming [ 65.987097] nvidia 0000:01:00.0: resuming [ 65.987237] pnp 00:00: resuming [ 65.987244] serial 00:01: resuming [ 65.988604] pnp: Device 00:01 activated. [ 65.988610] parport_pc 00:02: resuming [ 65.990224] pnp: Device 00:02 activated. [ 65.990227] system 00:03: resuming [ 65.990230] pnp 00:04: resuming [ 65.990233] pnp 00:05: resuming [ 65.990236] pnp 00:06: resuming [ 65.990239] pnp 00:07: resuming [ 65.990242] i8042 aux 00:08: resuming [ 65.990379] pnp: Failed to activate device 00:08. [ 65.990383] i8042 kbd 00:09: resuming [ 65.990398] pnp: Failed to activate device 00:09. [ 65.990407] pcspkr pcspkr: resuming [ 65.990410] platform vesafb.0: resuming [ 65.990449] serial8250 serial8250: resuming [ 65.990456] ide-disk 0.0: resuming [ 66.040883] ide-cdrom 1.0: resuming [ 66.043032] i8042 i8042: resuming [ 66.043065] atkbd serio0: resuming [ 66.075682] psmouse serio1: resuming [ 66.253841] logips2pp: Detected unknown logitech mouse model 62 [ 133.359431] usb usb5: resuming [ 133.391673] hub 5-0:1.0: resuming [ 133.391692] ac97 0-0:ALC850: resuming [ 133.391739] Restarting tasks ... done. ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: 2.6.20-rc6-mm3 2007-01-31 14:25 ` 2.6.20-rc6-mm3 Karsten Wiese @ 2007-02-01 8:01 ` Ingo Molnar 2007-02-01 10:44 ` 2.6.20-rc6-mm3 Karsten Wiese 2007-02-03 0:37 ` 2.6.20-rc6-mm3 Pavel Machek 0 siblings, 2 replies; 19+ messages in thread From: Ingo Molnar @ 2007-02-01 8:01 UTC (permalink / raw) To: Karsten Wiese; +Cc: Andrew Morton, Maciej Rutecki, linux-kernel, linux-acpi * Karsten Wiese <fzu@wemgehoertderstaat.de> wrote: > Serial port console is off here and the jiffies update fix doesn't > make a noticeable difference. ok, this eliminates my serial port theory. and this means i'm having trouble reproducing this problem locally. Maybe i tried it the wrong way: does it only occur with suspend-to-disk, or suspend-to-ram too? Does it need ACPI suspend-to-disk, or software-suspend? Ingo ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: 2.6.20-rc6-mm3 2007-02-01 8:01 ` 2.6.20-rc6-mm3 Ingo Molnar @ 2007-02-01 10:44 ` Karsten Wiese 2007-02-01 11:12 ` 2.6.20-rc6-mm3 Karsten Wiese 2007-02-01 11:12 ` 2.6.20-rc6-mm3 Karsten Wiese 2007-02-03 0:37 ` 2.6.20-rc6-mm3 Pavel Machek 1 sibling, 2 replies; 19+ messages in thread From: Karsten Wiese @ 2007-02-01 10:44 UTC (permalink / raw) To: Ingo Molnar; +Cc: Andrew Morton, Maciej Rutecki, linux-kernel, linux-acpi [-- Attachment #1: Type: text/plain, Size: 671 bytes --] Am Donnerstag, 1. Februar 2007 09:01 schrieb Ingo Molnar: > > and this means i'm having trouble reproducing this problem locally. > Maybe i tried it the wrong way: does it only occur with suspend-to-disk, > or suspend-to-ram too? Does it need ACPI suspend-to-disk, or > software-suspend? Haven't checked suspend-to-ram. I use pm-hibernate or "echo reboot > /sys/power/disk; echo disk > /sys/power/state". Thats software-suspend? I think the wait is caused by an interrupt starting somewhere under sysdev_resume(void). possibly lapic timer interrupt? Will try to trace that. 2.6.20-rc6-rt6 .config attached. Machine is AMD64 UP, VIA chipset desktop. Karsten [-- Attachment #2: .config --] [-- Type: text/plain, Size: 50162 bytes --] # # Automatically generated make config: don't edit # Linux kernel version: 2.6.20-rc6-rt6 # Thu Feb 1 00:25:31 2007 # CONFIG_X86_32=y CONFIG_GENERIC_TIME=y CONFIG_CLOCKSOURCE_WATCHDOG=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_SEMAPHORE_SLEEPERS=y CONFIG_X86=y CONFIG_MMU=y CONFIG_GENERIC_ISA_DMA=y CONFIG_GENERIC_IOMAP=y CONFIG_GENERIC_BUG=y CONFIG_GENERIC_HWEIGHT=y CONFIG_ARCH_MAY_HAVE_PC_FDC=y CONFIG_DMI=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" # # Code maturity level options # CONFIG_EXPERIMENTAL=y CONFIG_BROKEN_ON_SMP=y CONFIG_LOCK_KERNEL=y CONFIG_INIT_ENV_ARG_LIMIT=32 # # General setup # CONFIG_LOCALVERSION=".dbg" # CONFIG_LOCALVERSION_AUTO is not set CONFIG_SWAP=y CONFIG_SYSVIPC=y # CONFIG_IPC_NS is not set CONFIG_POSIX_MQUEUE=y CONFIG_BSD_PROCESS_ACCT=y # CONFIG_BSD_PROCESS_ACCT_V3 is not set CONFIG_TASKSTATS=y CONFIG_TASK_DELAY_ACCT=y # CONFIG_UTS_NS is not set CONFIG_AUDIT=y CONFIG_AUDITSYSCALL=y # CONFIG_IKCONFIG is not set # CONFIG_SYSFS_DEPRECATED is not set CONFIG_RELAY=y CONFIG_INITRAMFS_SOURCE="" CONFIG_CC_OPTIMIZE_FOR_SIZE=y # CONFIG_TASK_XACCT is not set CONFIG_SYSCTL=y # CONFIG_EMBEDDED is not set CONFIG_UID16=y CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y CONFIG_KALLSYMS_ALL=y # CONFIG_KALLSYMS_EXTRA_PASS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_ELF_CORE=y CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y CONFIG_SLAB=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 # CONFIG_SLOB is not set # # Loadable module support # CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y # # Block layer # CONFIG_BLOCK=y CONFIG_LBD=y CONFIG_BLK_DEV_IO_TRACE=y CONFIG_LSF=y # # IO Schedulers # CONFIG_IOSCHED_NOOP=y CONFIG_IOSCHED_AS=y CONFIG_IOSCHED_DEADLINE=y CONFIG_IOSCHED_CFQ=y # CONFIG_DEFAULT_AS is not set # CONFIG_DEFAULT_DEADLINE is not set CONFIG_DEFAULT_CFQ=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="cfq" # # Processor type and features # CONFIG_TICK_ONESHOT=y CONFIG_NO_HZ=y CONFIG_HIGH_RES_TIMERS=y # CONFIG_SMP is not set CONFIG_X86_PC=y # CONFIG_X86_ELAN is not set # CONFIG_X86_VOYAGER is not set # CONFIG_X86_NUMAQ is not set # CONFIG_X86_SUMMIT is not set # CONFIG_X86_BIGSMP is not set # CONFIG_X86_VISWS is not set # CONFIG_X86_GENERICARCH is not set # CONFIG_X86_ES7000 is not set # CONFIG_PARAVIRT is not set # CONFIG_M386 is not set # CONFIG_M486 is not set # CONFIG_M586 is not set # CONFIG_M586TSC is not set # CONFIG_M586MMX is not set # CONFIG_M686 is not set # CONFIG_MPENTIUMII is not set # CONFIG_MPENTIUMIII is not set # CONFIG_MPENTIUMM is not set # CONFIG_MCORE2 is not set # CONFIG_MPENTIUM4 is not set # CONFIG_MK6 is not set # CONFIG_MK7 is not set CONFIG_MK8=y # CONFIG_MCRUSOE is not set # CONFIG_MEFFICEON is not set # CONFIG_MWINCHIPC6 is not set # CONFIG_MWINCHIP2 is not set # CONFIG_MWINCHIP3D is not set # CONFIG_MGEODEGX1 is not set # CONFIG_MGEODE_LX is not set # CONFIG_MCYRIXIII is not set # CONFIG_MVIAC3_2 is not set # CONFIG_X86_GENERIC is not set CONFIG_X86_CMPXCHG=y CONFIG_X86_XADD=y CONFIG_X86_L1_CACHE_SHIFT=6 CONFIG_RWSEM_GENERIC_SPINLOCK=y # CONFIG_ARCH_HAS_ILOG2_U32 is not set # CONFIG_ARCH_HAS_ILOG2_U64 is not set CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_X86_WP_WORKS_OK=y CONFIG_X86_INVLPG=y CONFIG_X86_BSWAP=y CONFIG_X86_POPAD_OK=y CONFIG_X86_CMPXCHG64=y CONFIG_X86_GOOD_APIC=y CONFIG_X86_INTEL_USERCOPY=y CONFIG_X86_USE_PPRO_CHECKSUM=y CONFIG_X86_TSC=y CONFIG_HPET_TIMER=y CONFIG_HPET_EMULATE_RTC=y # CONFIG_PREEMPT_NONE is not set # CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT_DESKTOP is not set CONFIG_PREEMPT_RT=y CONFIG_PREEMPT=y CONFIG_PREEMPT_SOFTIRQS=y CONFIG_PREEMPT_HARDIRQS=y CONFIG_PREEMPT_BKL=y # CONFIG_CLASSIC_RCU is not set CONFIG_PREEMPT_RCU=y CONFIG_RCU_TRACE=y CONFIG_ASM_SEMAPHORES=y CONFIG_X86_UP_APIC=y CONFIG_X86_UP_IOAPIC=y CONFIG_X86_LOCAL_APIC=y CONFIG_X86_IO_APIC=y CONFIG_X86_MCE=y # CONFIG_X86_MCE_NONFATAL is not set # CONFIG_X86_MCE_P4THERMAL is not set CONFIG_VM86=y # CONFIG_TOSHIBA is not set # CONFIG_I8K is not set # CONFIG_X86_REBOOTFIXUPS is not set # CONFIG_MICROCODE is not set CONFIG_X86_MSR=m CONFIG_X86_CPUID=m # # Firmware Drivers # CONFIG_EDD=m CONFIG_DELL_RBU=m CONFIG_DCDBAS=m # CONFIG_NOHIGHMEM is not set CONFIG_HIGHMEM4G=y # CONFIG_HIGHMEM64G is not set CONFIG_PAGE_OFFSET=0xC0000000 CONFIG_HIGHMEM=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_ARCH_SPARSEMEM_ENABLE=y CONFIG_ARCH_SELECT_MEMORY_MODEL=y CONFIG_ARCH_POPULATES_NODE_MAP=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y # CONFIG_DISCONTIGMEM_MANUAL is not set # CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_SPARSEMEM_STATIC=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_HIGHPTE=y # CONFIG_MATH_EMULATION is not set CONFIG_MTRR=y # CONFIG_EFI is not set # CONFIG_SECCOMP is not set # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set # CONFIG_HZ_1000 is not set CONFIG_HZ=250 CONFIG_KEXEC=y # CONFIG_CRASH_DUMP is not set CONFIG_PHYSICAL_START=0x100000 # CONFIG_RELOCATABLE is not set CONFIG_PHYSICAL_ALIGN=0x100000 # CONFIG_COMPAT_VDSO is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y # # Power management options (ACPI, APM) # CONFIG_PM=y CONFIG_PM_LEGACY=y # CONFIG_PM_DEBUG is not set CONFIG_PM_SYSFS_DEPRECATED=y CONFIG_SOFTWARE_SUSPEND=y CONFIG_PM_STD_PARTITION="" # # ACPI (Advanced Configuration and Power Interface) Support # CONFIG_ACPI=y CONFIG_ACPI_SLEEP=y CONFIG_ACPI_SLEEP_PROC_FS=y # CONFIG_ACPI_SLEEP_PROC_SLEEP is not set CONFIG_ACPI_AC=m CONFIG_ACPI_BATTERY=m CONFIG_ACPI_BUTTON=m CONFIG_ACPI_VIDEO=m # CONFIG_ACPI_HOTKEY is not set CONFIG_ACPI_FAN=y CONFIG_ACPI_DOCK=m # CONFIG_ACPI_PROCESSOR is not set CONFIG_ACPI_ASUS=m CONFIG_ACPI_IBM=m CONFIG_ACPI_TOSHIBA=m CONFIG_ACPI_BLACKLIST_YEAR=1999 # CONFIG_ACPI_DEBUG is not set CONFIG_ACPI_EC=y CONFIG_ACPI_POWER=y CONFIG_ACPI_SYSTEM=y CONFIG_X86_PM_TIMER=y CONFIG_ACPI_CONTAINER=y CONFIG_ACPI_SBS=m # # APM (Advanced Power Management) BIOS Support # CONFIG_APM=y # CONFIG_APM_IGNORE_USER_SUSPEND is not set # CONFIG_APM_DO_ENABLE is not set # CONFIG_APM_CPU_IDLE is not set # CONFIG_APM_DISPLAY_BLANK is not set CONFIG_APM_RTC_IS_GMT=y # CONFIG_APM_ALLOW_INTS is not set # CONFIG_APM_REAL_MODE_POWER_OFF is not set # # CPU Frequency scaling # CONFIG_CPU_FREQ=y CONFIG_CPU_FREQ_TABLE=m CONFIG_CPU_FREQ_DEBUG=y CONFIG_CPU_FREQ_STAT=m CONFIG_CPU_FREQ_STAT_DETAILS=y # CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y CONFIG_CPU_FREQ_GOV_PERFORMANCE=y CONFIG_CPU_FREQ_GOV_POWERSAVE=m CONFIG_CPU_FREQ_GOV_USERSPACE=y CONFIG_CPU_FREQ_GOV_ONDEMAND=m CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m # # CPUFreq processor drivers # # CONFIG_X86_POWERNOW_K6 is not set # CONFIG_X86_POWERNOW_K7 is not set CONFIG_X86_POWERNOW_K8=m # CONFIG_X86_GX_SUSPMOD is not set # CONFIG_X86_SPEEDSTEP_CENTRINO is not set # CONFIG_X86_SPEEDSTEP_ICH is not set # CONFIG_X86_SPEEDSTEP_SMI is not set # CONFIG_X86_P4_CLOCKMOD is not set # CONFIG_X86_CPUFREQ_NFORCE2 is not set # CONFIG_X86_LONGRUN is not set # # shared options # # CONFIG_X86_SPEEDSTEP_LIB is not set # # Bus options (PCI, PCMCIA, EISA, MCA, ISA) # CONFIG_PCI=y # CONFIG_PCI_GOBIOS is not set # CONFIG_PCI_GOMMCONFIG is not set # CONFIG_PCI_GODIRECT is not set CONFIG_PCI_GOANY=y CONFIG_PCI_BIOS=y CONFIG_PCI_DIRECT=y CONFIG_PCI_MMCONFIG=y # CONFIG_PCIEPORTBUS is not set # CONFIG_PCI_MSI is not set # CONFIG_PCI_DEBUG is not set CONFIG_HT_IRQ=y CONFIG_ISA_DMA_API=y # CONFIG_ISA is not set # CONFIG_MCA is not set # CONFIG_SCx200 is not set CONFIG_K8_NB=y # # PCCARD (PCMCIA/CardBus) support # # CONFIG_PCCARD is not set # # PCI Hotplug Support # CONFIG_HOTPLUG_PCI=y CONFIG_HOTPLUG_PCI_FAKE=m CONFIG_HOTPLUG_PCI_COMPAQ=m # CONFIG_HOTPLUG_PCI_COMPAQ_NVRAM is not set # CONFIG_HOTPLUG_PCI_IBM is not set CONFIG_HOTPLUG_PCI_ACPI=m CONFIG_HOTPLUG_PCI_ACPI_IBM=m # CONFIG_HOTPLUG_PCI_CPCI is not set # CONFIG_HOTPLUG_PCI_SHPC is not set # # Executable file formats # CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_AOUT is not set CONFIG_BINFMT_MISC=y # # Networking # CONFIG_NET=y # # Networking options # # CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y CONFIG_XFRM=y CONFIG_XFRM_USER=y # CONFIG_XFRM_SUB_POLICY is not set CONFIG_NET_KEY=m CONFIG_INET=y CONFIG_IP_MULTICAST=y CONFIG_IP_ADVANCED_ROUTER=y CONFIG_ASK_IP_FIB_HASH=y # CONFIG_IP_FIB_TRIE is not set CONFIG_IP_FIB_HASH=y CONFIG_IP_MULTIPLE_TABLES=y CONFIG_IP_ROUTE_MULTIPATH=y # CONFIG_IP_ROUTE_MULTIPATH_CACHED is not set CONFIG_IP_ROUTE_VERBOSE=y # CONFIG_IP_PNP is not set CONFIG_NET_IPIP=m CONFIG_NET_IPGRE=m CONFIG_NET_IPGRE_BROADCAST=y CONFIG_IP_MROUTE=y CONFIG_IP_PIMSM_V1=y CONFIG_IP_PIMSM_V2=y # CONFIG_ARPD is not set CONFIG_SYN_COOKIES=y CONFIG_INET_AH=m CONFIG_INET_ESP=m CONFIG_INET_IPCOMP=m CONFIG_INET_XFRM_TUNNEL=m CONFIG_INET_TUNNEL=m CONFIG_INET_XFRM_MODE_TRANSPORT=m CONFIG_INET_XFRM_MODE_TUNNEL=m CONFIG_INET_XFRM_MODE_BEET=m CONFIG_INET_DIAG=m CONFIG_INET_TCP_DIAG=m CONFIG_TCP_CONG_ADVANCED=y CONFIG_TCP_CONG_BIC=y CONFIG_TCP_CONG_CUBIC=m CONFIG_TCP_CONG_WESTWOOD=m CONFIG_TCP_CONG_HTCP=m CONFIG_TCP_CONG_HSTCP=m CONFIG_TCP_CONG_HYBLA=m CONFIG_TCP_CONG_VEGAS=m CONFIG_TCP_CONG_SCALABLE=m CONFIG_TCP_CONG_LP=m CONFIG_TCP_CONG_VENO=m CONFIG_DEFAULT_BIC=y # CONFIG_DEFAULT_CUBIC is not set # CONFIG_DEFAULT_HTCP is not set # CONFIG_DEFAULT_VEGAS is not set # CONFIG_DEFAULT_WESTWOOD is not set # CONFIG_DEFAULT_RENO is not set CONFIG_DEFAULT_TCP_CONG="bic" # CONFIG_TCP_MD5SIG is not set # # IP: Virtual Server Configuration # CONFIG_IP_VS=m # CONFIG_IP_VS_DEBUG is not set CONFIG_IP_VS_TAB_BITS=12 # # IPVS transport protocol load balancing support # CONFIG_IP_VS_PROTO_TCP=y CONFIG_IP_VS_PROTO_UDP=y CONFIG_IP_VS_PROTO_ESP=y CONFIG_IP_VS_PROTO_AH=y # # IPVS scheduler # CONFIG_IP_VS_RR=m CONFIG_IP_VS_WRR=m CONFIG_IP_VS_LC=m CONFIG_IP_VS_WLC=m CONFIG_IP_VS_LBLC=m CONFIG_IP_VS_LBLCR=m CONFIG_IP_VS_DH=m CONFIG_IP_VS_SH=m CONFIG_IP_VS_SED=m CONFIG_IP_VS_NQ=m # # IPVS application helper # CONFIG_IP_VS_FTP=m # CONFIG_IPV6 is not set # CONFIG_INET6_XFRM_TUNNEL is not set # CONFIG_INET6_TUNNEL is not set CONFIG_NETLABEL=y CONFIG_NETWORK_SECMARK=y CONFIG_NETFILTER=y # CONFIG_NETFILTER_DEBUG is not set CONFIG_BRIDGE_NETFILTER=y # # Core Netfilter Configuration # CONFIG_NETFILTER_NETLINK=m CONFIG_NETFILTER_NETLINK_QUEUE=m CONFIG_NETFILTER_NETLINK_LOG=m # CONFIG_NF_CONNTRACK_ENABLED is not set CONFIG_NETFILTER_XTABLES=m CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m CONFIG_NETFILTER_XT_TARGET_DSCP=m CONFIG_NETFILTER_XT_TARGET_MARK=m CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m # CONFIG_NETFILTER_XT_TARGET_NFLOG is not set CONFIG_NETFILTER_XT_TARGET_SECMARK=m CONFIG_NETFILTER_XT_MATCH_COMMENT=m CONFIG_NETFILTER_XT_MATCH_DCCP=m CONFIG_NETFILTER_XT_MATCH_DSCP=m CONFIG_NETFILTER_XT_MATCH_ESP=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m CONFIG_NETFILTER_XT_MATCH_POLICY=m CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_QUOTA=m CONFIG_NETFILTER_XT_MATCH_REALM=m CONFIG_NETFILTER_XT_MATCH_SCTP=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m # CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set # # IP: Netfilter Configuration # CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m CONFIG_IP_NF_MATCH_IPRANGE=m CONFIG_IP_NF_MATCH_TOS=m CONFIG_IP_NF_MATCH_RECENT=m CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_AH=m CONFIG_IP_NF_MATCH_TTL=m CONFIG_IP_NF_MATCH_OWNER=m CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m CONFIG_IP_NF_TARGET_ULOG=m CONFIG_IP_NF_TARGET_TCPMSS=m CONFIG_IP_NF_MANGLE=m CONFIG_IP_NF_TARGET_TOS=m CONFIG_IP_NF_TARGET_ECN=m CONFIG_IP_NF_TARGET_TTL=m CONFIG_IP_NF_RAW=m CONFIG_IP_NF_ARPTABLES=m CONFIG_IP_NF_ARPFILTER=m CONFIG_IP_NF_ARP_MANGLE=m # # Bridge: Netfilter Configuration # CONFIG_BRIDGE_NF_EBTABLES=m CONFIG_BRIDGE_EBT_BROUTE=m CONFIG_BRIDGE_EBT_T_FILTER=m CONFIG_BRIDGE_EBT_T_NAT=m CONFIG_BRIDGE_EBT_802_3=m CONFIG_BRIDGE_EBT_AMONG=m CONFIG_BRIDGE_EBT_ARP=m CONFIG_BRIDGE_EBT_IP=m CONFIG_BRIDGE_EBT_LIMIT=m CONFIG_BRIDGE_EBT_MARK=m CONFIG_BRIDGE_EBT_PKTTYPE=m CONFIG_BRIDGE_EBT_STP=m CONFIG_BRIDGE_EBT_VLAN=m CONFIG_BRIDGE_EBT_ARPREPLY=m CONFIG_BRIDGE_EBT_DNAT=m CONFIG_BRIDGE_EBT_MARK_T=m CONFIG_BRIDGE_EBT_REDIRECT=m CONFIG_BRIDGE_EBT_SNAT=m CONFIG_BRIDGE_EBT_LOG=m CONFIG_BRIDGE_EBT_ULOG=m # # DCCP Configuration (EXPERIMENTAL) # # CONFIG_IP_DCCP is not set # # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set # # TIPC Configuration (EXPERIMENTAL) # # CONFIG_TIPC is not set # CONFIG_ATM is not set CONFIG_BRIDGE=m CONFIG_VLAN_8021Q=m # CONFIG_DECNET is not set CONFIG_LLC=m # CONFIG_LLC2 is not set # CONFIG_IPX is not set # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # # QoS and/or fair queueing # CONFIG_NET_SCHED=y CONFIG_NET_SCH_FIFO=y # CONFIG_NET_SCH_CLK_JIFFIES is not set CONFIG_NET_SCH_CLK_GETTIMEOFDAY=y # CONFIG_NET_SCH_CLK_CPU is not set # # Queueing/Scheduling # CONFIG_NET_SCH_CBQ=m CONFIG_NET_SCH_HTB=m CONFIG_NET_SCH_HFSC=m CONFIG_NET_SCH_PRIO=m CONFIG_NET_SCH_RED=m CONFIG_NET_SCH_SFQ=m CONFIG_NET_SCH_TEQL=m CONFIG_NET_SCH_TBF=m CONFIG_NET_SCH_GRED=m CONFIG_NET_SCH_DSMARK=m CONFIG_NET_SCH_NETEM=m CONFIG_NET_SCH_INGRESS=m # # Classification # CONFIG_NET_CLS=y CONFIG_NET_CLS_BASIC=m CONFIG_NET_CLS_TCINDEX=m CONFIG_NET_CLS_ROUTE4=m CONFIG_NET_CLS_ROUTE=y CONFIG_NET_CLS_FW=m CONFIG_NET_CLS_U32=m CONFIG_CLS_U32_PERF=y CONFIG_CLS_U32_MARK=y CONFIG_NET_CLS_RSVP=m CONFIG_NET_CLS_RSVP6=m CONFIG_NET_EMATCH=y CONFIG_NET_EMATCH_STACK=32 CONFIG_NET_EMATCH_CMP=m CONFIG_NET_EMATCH_NBYTE=m CONFIG_NET_EMATCH_U32=m CONFIG_NET_EMATCH_META=m CONFIG_NET_EMATCH_TEXT=m CONFIG_NET_CLS_ACT=y CONFIG_NET_ACT_POLICE=m CONFIG_NET_ACT_GACT=m CONFIG_GACT_PROB=y CONFIG_NET_ACT_MIRRED=m CONFIG_NET_ACT_IPT=m CONFIG_NET_ACT_PEDIT=m CONFIG_NET_ACT_SIMP=m CONFIG_NET_CLS_IND=y CONFIG_NET_ESTIMATOR=y # # Network testing # CONFIG_NET_PKTGEN=m # CONFIG_NET_TCPPROBE is not set # CONFIG_HAMRADIO is not set # CONFIG_IRDA is not set # CONFIG_BT is not set CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m CONFIG_IEEE80211_SOFTMAC=m CONFIG_IEEE80211_SOFTMAC_DEBUG=y CONFIG_WIRELESS_EXT=y CONFIG_FIB_RULES=y # # Device Drivers # # # Generic Driver Options # CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y # CONFIG_DEBUG_DRIVER is not set # CONFIG_SYS_HYPERVISOR is not set # # Connector - unified userspace <-> kernelspace linker # CONFIG_CONNECTOR=y CONFIG_PROC_EVENTS=y # # Memory Technology Devices (MTD) # # CONFIG_MTD is not set # # Parallel port support # CONFIG_PARPORT=m CONFIG_PARPORT_PC=m CONFIG_PARPORT_SERIAL=m # CONFIG_PARPORT_PC_FIFO is not set # CONFIG_PARPORT_PC_SUPERIO is not set # CONFIG_PARPORT_GSC is not set # CONFIG_PARPORT_AX88796 is not set CONFIG_PARPORT_1284=y # # Plug and Play support # CONFIG_PNP=y # CONFIG_PNP_DEBUG is not set # # Protocols # CONFIG_PNPACPI=y # # Block devices # CONFIG_BLK_DEV_FD=m # CONFIG_PARIDE is not set # CONFIG_BLK_CPQ_DA is not set # CONFIG_BLK_CPQ_CISS_DA is not set # CONFIG_BLK_DEV_DAC960 is not set # CONFIG_BLK_DEV_UMEM is not set # CONFIG_BLK_DEV_COW_COMMON is not set CONFIG_BLK_DEV_LOOP=m CONFIG_BLK_DEV_CRYPTOLOOP=m CONFIG_BLK_DEV_NBD=m # CONFIG_BLK_DEV_SX8 is not set CONFIG_BLK_DEV_UB=m CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=16384 CONFIG_BLK_DEV_RAM_BLOCKSIZE=4096 CONFIG_BLK_DEV_INITRD=y CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set # CONFIG_ATA_OVER_ETH is not set # # Misc devices # # CONFIG_IBM_ASM is not set # CONFIG_SGI_IOC4 is not set CONFIG_TIFM_CORE=m CONFIG_TIFM_7XX1=m # CONFIG_MSI_LAPTOP is not set # # ATA/ATAPI/MFM/RLL support # CONFIG_IDE=y CONFIG_BLK_DEV_IDE=y # # Please see Documentation/ide.txt for help/info on IDE drives # # CONFIG_BLK_DEV_IDE_SATA is not set # CONFIG_BLK_DEV_HD_IDE is not set CONFIG_BLK_DEV_IDEDISK=y CONFIG_IDEDISK_MULTI_MODE=y CONFIG_BLK_DEV_IDECD=m # CONFIG_BLK_DEV_IDETAPE is not set # CONFIG_BLK_DEV_IDEFLOPPY is not set CONFIG_BLK_DEV_IDESCSI=m CONFIG_IDE_TASK_IOCTL=y # # IDE chipset support/bugfixes # CONFIG_IDE_GENERIC=y # CONFIG_BLK_DEV_CMD640 is not set # CONFIG_BLK_DEV_IDEPNP is not set CONFIG_BLK_DEV_IDEPCI=y CONFIG_IDEPCI_SHARE_IRQ=y # CONFIG_BLK_DEV_OFFBOARD is not set CONFIG_BLK_DEV_GENERIC=y # CONFIG_BLK_DEV_OPTI621 is not set # CONFIG_BLK_DEV_RZ1000 is not set CONFIG_BLK_DEV_IDEDMA_PCI=y # CONFIG_BLK_DEV_IDEDMA_FORCED is not set CONFIG_IDEDMA_PCI_AUTO=y # CONFIG_IDEDMA_ONLYDISK is not set # CONFIG_BLK_DEV_AEC62XX is not set # CONFIG_BLK_DEV_ALI15X3 is not set # CONFIG_BLK_DEV_AMD74XX is not set # CONFIG_BLK_DEV_ATIIXP is not set # CONFIG_BLK_DEV_CMD64X is not set # CONFIG_BLK_DEV_TRIFLEX is not set # CONFIG_BLK_DEV_CY82C693 is not set # CONFIG_BLK_DEV_CS5520 is not set # CONFIG_BLK_DEV_CS5530 is not set # CONFIG_BLK_DEV_CS5535 is not set # CONFIG_BLK_DEV_HPT34X is not set # CONFIG_BLK_DEV_HPT366 is not set # CONFIG_BLK_DEV_JMICRON is not set # CONFIG_BLK_DEV_SC1200 is not set # CONFIG_BLK_DEV_PIIX is not set # CONFIG_BLK_DEV_IT821X is not set # CONFIG_BLK_DEV_NS87415 is not set # CONFIG_BLK_DEV_PDC202XX_OLD is not set # CONFIG_BLK_DEV_PDC202XX_NEW is not set # CONFIG_BLK_DEV_SVWKS is not set # CONFIG_BLK_DEV_SIIMAGE is not set # CONFIG_BLK_DEV_SIS5513 is not set # CONFIG_BLK_DEV_SLC90E66 is not set # CONFIG_BLK_DEV_TRM290 is not set CONFIG_BLK_DEV_VIA82CXXX=y # CONFIG_IDE_ARM is not set CONFIG_BLK_DEV_IDEDMA=y # CONFIG_IDEDMA_IVB is not set CONFIG_IDEDMA_AUTO=y # CONFIG_BLK_DEV_HD is not set # # SCSI device support # CONFIG_RAID_ATTRS=m CONFIG_SCSI=m # CONFIG_SCSI_TGT is not set CONFIG_SCSI_NETLINK=y CONFIG_SCSI_PROC_FS=y # # SCSI support type (disk, tape, CD-ROM) # CONFIG_BLK_DEV_SD=m # CONFIG_CHR_DEV_ST is not set # CONFIG_CHR_DEV_OSST is not set CONFIG_BLK_DEV_SR=m CONFIG_BLK_DEV_SR_VENDOR=y CONFIG_CHR_DEV_SG=m CONFIG_CHR_DEV_SCH=m # # Some SCSI devices (e.g. CD jukebox) support multiple LUNs # CONFIG_SCSI_MULTI_LUN=y CONFIG_SCSI_CONSTANTS=y CONFIG_SCSI_LOGGING=y # CONFIG_SCSI_SCAN_ASYNC is not set # # SCSI Transports # CONFIG_SCSI_SPI_ATTRS=m CONFIG_SCSI_FC_ATTRS=m CONFIG_SCSI_ISCSI_ATTRS=m CONFIG_SCSI_SAS_ATTRS=m CONFIG_SCSI_SAS_LIBSAS=m # CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set # # SCSI low-level drivers # CONFIG_ISCSI_TCP=m # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set # CONFIG_SCSI_AACRAID is not set # CONFIG_SCSI_AIC7XXX is not set # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set # CONFIG_MEGARAID_SAS is not set # CONFIG_SCSI_HPTIOP is not set # CONFIG_SCSI_BUSLOGIC is not set # CONFIG_SCSI_DMX3191D is not set # CONFIG_SCSI_EATA is not set # CONFIG_SCSI_FUTURE_DOMAIN is not set # CONFIG_SCSI_GDTH is not set # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set # CONFIG_SCSI_PPA is not set # CONFIG_SCSI_IMM is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_QLOGIC_1280 is not set # CONFIG_SCSI_QLA_FC is not set # CONFIG_SCSI_QLA_ISCSI is not set # CONFIG_SCSI_LPFC is not set # CONFIG_SCSI_DC395x is not set # CONFIG_SCSI_DC390T is not set # CONFIG_SCSI_NSP32 is not set # CONFIG_SCSI_DEBUG is not set # CONFIG_SCSI_SRP is not set # # Serial ATA (prod) and Parallel ATA (experimental) drivers # # CONFIG_ATA is not set # # Multi-device support (RAID and LVM) # # CONFIG_MD is not set # # Fusion MPT device support # # CONFIG_FUSION is not set # CONFIG_FUSION_SPI is not set # CONFIG_FUSION_FC is not set # CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support # # CONFIG_IEEE1394 is not set # # I2O device support # CONFIG_I2O=m # CONFIG_I2O_LCT_NOTIFY_ON_CHANGES is not set CONFIG_I2O_EXT_ADAPTEC=y CONFIG_I2O_CONFIG=m CONFIG_I2O_CONFIG_OLD_IOCTL=y CONFIG_I2O_BUS=m CONFIG_I2O_BLOCK=m CONFIG_I2O_SCSI=m CONFIG_I2O_PROC=m # # Network device support # CONFIG_NETDEVICES=y CONFIG_IFB=m CONFIG_DUMMY=m CONFIG_BONDING=m # CONFIG_EQUALIZER is not set CONFIG_TUN=m # CONFIG_NET_SB1000 is not set # # ARCnet devices # # CONFIG_ARCNET is not set # # PHY device support # # # Ethernet (10 or 100Mbit) # # CONFIG_NET_ETHERNET is not set # # Ethernet (1000 Mbit) # # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set CONFIG_R8169=m CONFIG_R8169_NAPI=y CONFIG_R8169_VLAN=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set # CONFIG_SK98LIN is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set # CONFIG_QLA3XXX is not set # # Ethernet (10000 Mbit) # # CONFIG_CHELSIO_T1 is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set # # Token Ring devices # # CONFIG_TR is not set # # Wireless LAN (non-hamradio) # # CONFIG_NET_RADIO is not set # # Wan interfaces # # CONFIG_WAN is not set # CONFIG_FDDI is not set # CONFIG_HIPPI is not set # CONFIG_PLIP is not set # CONFIG_PPP is not set # CONFIG_SLIP is not set # CONFIG_NET_FC is not set # CONFIG_SHAPER is not set CONFIG_NETCONSOLE=m CONFIG_NETPOLL=y # CONFIG_NETPOLL_RX is not set CONFIG_NETPOLL_TRAP=y CONFIG_NET_POLL_CONTROLLER=y # # ISDN subsystem # # CONFIG_ISDN is not set # # Telephony Support # # CONFIG_PHONE is not set # # Input device support # CONFIG_INPUT=y CONFIG_INPUT_FF_MEMLESS=y # # Userland interfaces # CONFIG_INPUT_MOUSEDEV=y # CONFIG_INPUT_MOUSEDEV_PSAUX is not set CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set # CONFIG_INPUT_TSDEV is not set CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_EVBUG is not set # # Input Device Drivers # CONFIG_INPUT_KEYBOARD=y CONFIG_KEYBOARD_ATKBD=y # CONFIG_KEYBOARD_SUNKBD is not set # CONFIG_KEYBOARD_LKKBD is not set # CONFIG_KEYBOARD_XTKBD is not set # CONFIG_KEYBOARD_NEWTON is not set CONFIG_KEYBOARD_STOWAWAY=m CONFIG_INPUT_MOUSE=y CONFIG_MOUSE_PS2=y CONFIG_MOUSE_SERIAL=m CONFIG_MOUSE_VSXXXAA=m # CONFIG_INPUT_JOYSTICK is not set # CONFIG_INPUT_TOUCHSCREEN is not set CONFIG_INPUT_MISC=y CONFIG_INPUT_PCSPKR=m # CONFIG_INPUT_WISTRON_BTNS is not set # CONFIG_INPUT_UINPUT is not set # # Hardware I/O ports # CONFIG_SERIO=y CONFIG_SERIO_I8042=y CONFIG_SERIO_SERPORT=y # CONFIG_SERIO_CT82C710 is not set # CONFIG_SERIO_PARKBD is not set # CONFIG_SERIO_PCIPS2 is not set CONFIG_SERIO_LIBPS2=y CONFIG_SERIO_RAW=m CONFIG_GAMEPORT=m # CONFIG_GAMEPORT_NS558 is not set # CONFIG_GAMEPORT_L4 is not set # CONFIG_GAMEPORT_EMU10K1 is not set # CONFIG_GAMEPORT_FM801 is not set # # Character devices # CONFIG_VT=y CONFIG_VT_CONSOLE=y CONFIG_HW_CONSOLE=y CONFIG_VT_HW_CONSOLE_BINDING=y # CONFIG_SERIAL_NONSTANDARD is not set # # Serial drivers # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y CONFIG_SERIAL_8250_PCI=y CONFIG_SERIAL_8250_PNP=y CONFIG_SERIAL_8250_NR_UARTS=32 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 CONFIG_SERIAL_8250_EXTENDED=y CONFIG_SERIAL_8250_MANY_PORTS=y CONFIG_SERIAL_8250_SHARE_IRQ=y CONFIG_SERIAL_8250_DETECT_IRQ=y CONFIG_SERIAL_8250_RSA=y # # Non-8250 serial port support # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y CONFIG_SERIAL_JSM=m CONFIG_UNIX98_PTYS=y # CONFIG_LEGACY_PTYS is not set CONFIG_PRINTER=m # CONFIG_LP_CONSOLE is not set # CONFIG_PPDEV is not set # CONFIG_TIPAR is not set # # IPMI # CONFIG_IPMI_HANDLER=m # CONFIG_IPMI_PANIC_EVENT is not set CONFIG_IPMI_DEVICE_INTERFACE=m CONFIG_IPMI_SI=m CONFIG_IPMI_WATCHDOG=m CONFIG_IPMI_POWEROFF=m # # Watchdog Cards # CONFIG_WATCHDOG=y # CONFIG_WATCHDOG_NOWAYOUT is not set # # Watchdog Device Drivers # CONFIG_SOFT_WATCHDOG=m # CONFIG_ACQUIRE_WDT is not set # CONFIG_ADVANTECH_WDT is not set # CONFIG_ALIM1535_WDT is not set # CONFIG_ALIM7101_WDT is not set # CONFIG_SC520_WDT is not set # CONFIG_EUROTECH_WDT is not set # CONFIG_IB700_WDT is not set # CONFIG_IBMASR is not set # CONFIG_WAFER_WDT is not set # CONFIG_I6300ESB_WDT is not set # CONFIG_I8XX_TCO is not set # CONFIG_ITCO_WDT is not set # CONFIG_SC1200_WDT is not set # CONFIG_PC87413_WDT is not set # CONFIG_60XX_WDT is not set # CONFIG_SBC8360_WDT is not set # CONFIG_CPU5_WDT is not set # CONFIG_SMSC37B787_WDT is not set CONFIG_W83627HF_WDT=m CONFIG_W83697HF_WDT=m CONFIG_W83877F_WDT=m CONFIG_W83977F_WDT=m # CONFIG_MACHZ_WDT is not set # CONFIG_SBC_EPX_C3_WATCHDOG is not set # # PCI-based Watchdog Cards # # CONFIG_PCIPCWATCHDOG is not set # CONFIG_WDTPCI is not set # # USB-based Watchdog Cards # # CONFIG_USBPCWATCHDOG is not set CONFIG_HW_RANDOM=y CONFIG_HW_RANDOM_INTEL=m # CONFIG_HW_RANDOM_AMD is not set # CONFIG_HW_RANDOM_GEODE is not set CONFIG_HW_RANDOM_VIA=m CONFIG_NVRAM=y CONFIG_RTC=y # CONFIG_RTC_HISTOGRAM is not set # CONFIG_BLOCKER is not set # CONFIG_LPPTEST is not set # CONFIG_DTLK is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set # CONFIG_SONYPI is not set CONFIG_AGP=y # CONFIG_AGP_ALI is not set # CONFIG_AGP_ATI is not set # CONFIG_AGP_AMD is not set CONFIG_AGP_AMD64=y # CONFIG_AGP_INTEL is not set # CONFIG_AGP_NVIDIA is not set # CONFIG_AGP_SIS is not set # CONFIG_AGP_SWORKS is not set # CONFIG_AGP_VIA is not set # CONFIG_AGP_EFFICEON is not set CONFIG_DRM=m # CONFIG_DRM_TDFX is not set # CONFIG_DRM_R128 is not set # CONFIG_DRM_RADEON is not set # CONFIG_DRM_MGA is not set # CONFIG_DRM_SIS is not set # CONFIG_DRM_VIA is not set # CONFIG_DRM_SAVAGE is not set # CONFIG_MWAVE is not set CONFIG_PC8736x_GPIO=m CONFIG_NSC_GPIO=m # CONFIG_CS5535_GPIO is not set # CONFIG_RAW_DRIVER is not set CONFIG_HPET=y # CONFIG_HPET_RTC_IRQ is not set # CONFIG_HPET_MMAP is not set CONFIG_HANGCHECK_TIMER=m # # TPM devices # CONFIG_TCG_TPM=m CONFIG_TCG_TIS=m CONFIG_TCG_NSC=m CONFIG_TCG_ATMEL=m CONFIG_TCG_INFINEON=m # CONFIG_TELCLOCK is not set # # I2C support # CONFIG_I2C=m CONFIG_I2C_CHARDEV=m # # I2C Algorithms # CONFIG_I2C_ALGOBIT=m CONFIG_I2C_ALGOPCF=m CONFIG_I2C_ALGOPCA=m # # I2C Hardware Bus support # # CONFIG_I2C_ALI1535 is not set # CONFIG_I2C_ALI1563 is not set # CONFIG_I2C_ALI15X3 is not set # CONFIG_I2C_AMD756 is not set # CONFIG_I2C_AMD8111 is not set CONFIG_I2C_I801=m CONFIG_I2C_I810=m CONFIG_I2C_PIIX4=m CONFIG_I2C_ISA=m # CONFIG_I2C_NFORCE2 is not set # CONFIG_I2C_OCORES is not set CONFIG_I2C_PARPORT=m CONFIG_I2C_PARPORT_LIGHT=m # CONFIG_I2C_PROSAVAGE is not set # CONFIG_I2C_SAVAGE4 is not set # CONFIG_SCx200_ACB is not set # CONFIG_I2C_SIS5595 is not set # CONFIG_I2C_SIS630 is not set # CONFIG_I2C_SIS96X is not set CONFIG_I2C_STUB=m # CONFIG_I2C_VIA is not set CONFIG_I2C_VIAPRO=m # CONFIG_I2C_VOODOO3 is not set # CONFIG_I2C_PCA_ISA is not set # # Miscellaneous I2C Chip support # CONFIG_SENSORS_DS1337=m CONFIG_SENSORS_DS1374=m CONFIG_SENSORS_EEPROM=m CONFIG_SENSORS_PCF8574=m CONFIG_SENSORS_PCA9539=m CONFIG_SENSORS_PCF8591=m CONFIG_SENSORS_MAX6875=m # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # # SPI support # # CONFIG_SPI is not set # CONFIG_SPI_MASTER is not set # # Dallas's 1-wire bus # # CONFIG_W1 is not set # # Hardware Monitoring support # CONFIG_HWMON=m CONFIG_HWMON_VID=m # CONFIG_SENSORS_ABITUGURU is not set # CONFIG_SENSORS_ADM1021 is not set # CONFIG_SENSORS_ADM1025 is not set # CONFIG_SENSORS_ADM1026 is not set # CONFIG_SENSORS_ADM1031 is not set # CONFIG_SENSORS_ADM9240 is not set CONFIG_SENSORS_K8TEMP=m # CONFIG_SENSORS_ASB100 is not set # CONFIG_SENSORS_ATXP1 is not set # CONFIG_SENSORS_DS1621 is not set # CONFIG_SENSORS_F71805F is not set # CONFIG_SENSORS_FSCHER is not set # CONFIG_SENSORS_FSCPOS is not set # CONFIG_SENSORS_GL518SM is not set # CONFIG_SENSORS_GL520SM is not set # CONFIG_SENSORS_IT87 is not set # CONFIG_SENSORS_LM63 is not set # CONFIG_SENSORS_LM75 is not set # CONFIG_SENSORS_LM77 is not set # CONFIG_SENSORS_LM78 is not set # CONFIG_SENSORS_LM80 is not set # CONFIG_SENSORS_LM83 is not set # CONFIG_SENSORS_LM85 is not set # CONFIG_SENSORS_LM87 is not set # CONFIG_SENSORS_LM90 is not set # CONFIG_SENSORS_LM92 is not set # CONFIG_SENSORS_MAX1619 is not set # CONFIG_SENSORS_PC87360 is not set # CONFIG_SENSORS_PC87427 is not set # CONFIG_SENSORS_SIS5595 is not set # CONFIG_SENSORS_SMSC47M1 is not set # CONFIG_SENSORS_SMSC47M192 is not set # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set CONFIG_SENSORS_VT8231=m CONFIG_SENSORS_W83781D=m CONFIG_SENSORS_W83791D=m CONFIG_SENSORS_W83792D=m # CONFIG_SENSORS_W83793 is not set CONFIG_SENSORS_W83L785TS=m CONFIG_SENSORS_W83627HF=m CONFIG_SENSORS_W83627EHF=m # CONFIG_SENSORS_HDAPS is not set # CONFIG_HWMON_DEBUG_CHIP is not set # # Multimedia devices # CONFIG_VIDEO_DEV=m CONFIG_VIDEO_V4L1=y CONFIG_VIDEO_V4L1_COMPAT=y CONFIG_VIDEO_V4L2=y # # Video Capture Adapters # # # Video Capture Adapters # # CONFIG_VIDEO_ADV_DEBUG is not set CONFIG_VIDEO_HELPER_CHIPS_AUTO=y CONFIG_VIDEO_VIVI=m # CONFIG_VIDEO_BT848 is not set # CONFIG_VIDEO_BWQCAM is not set # CONFIG_VIDEO_CQCAM is not set # CONFIG_VIDEO_W9966 is not set # CONFIG_VIDEO_CPIA is not set # CONFIG_VIDEO_CPIA2 is not set # CONFIG_VIDEO_SAA5246A is not set # CONFIG_VIDEO_SAA5249 is not set # CONFIG_TUNER_3036 is not set # CONFIG_VIDEO_STRADIS is not set # CONFIG_VIDEO_ZORAN is not set # CONFIG_VIDEO_SAA7134 is not set # CONFIG_VIDEO_MXB is not set # CONFIG_VIDEO_DPC is not set # CONFIG_VIDEO_HEXIUM_ORION is not set # CONFIG_VIDEO_HEXIUM_GEMINI is not set # CONFIG_VIDEO_CX88 is not set # CONFIG_VIDEO_CAFE_CCIC is not set # # V4L USB devices # # CONFIG_VIDEO_PVRUSB2 is not set # CONFIG_VIDEO_EM28XX is not set # CONFIG_VIDEO_USBVISION is not set # CONFIG_USB_VICAM is not set # CONFIG_USB_IBMCAM is not set # CONFIG_USB_KONICAWC is not set # CONFIG_USB_QUICKCAM_MESSENGER is not set # CONFIG_USB_ET61X251 is not set # CONFIG_VIDEO_OVCAMCHIP is not set # CONFIG_USB_W9968CF is not set # CONFIG_USB_OV511 is not set # CONFIG_USB_SE401 is not set # CONFIG_USB_SN9C102 is not set # CONFIG_USB_STV680 is not set # CONFIG_USB_ZC0301 is not set CONFIG_USB_PWC=m # CONFIG_USB_PWC_DEBUG is not set # # Radio Adapters # # CONFIG_RADIO_GEMTEK_PCI is not set # CONFIG_RADIO_MAXIRADIO is not set # CONFIG_RADIO_MAESTRO is not set # CONFIG_USB_DSBR is not set # # Digital Video Broadcasting Devices # CONFIG_DVB=y CONFIG_DVB_CORE=m # CONFIG_DVB_CORE_ATTACH is not set # # Supported SAA7146 based PCI Adapters # # CONFIG_DVB_AV7110 is not set # CONFIG_DVB_BUDGET is not set # CONFIG_DVB_BUDGET_CI is not set # CONFIG_DVB_BUDGET_AV is not set # # Supported USB Adapters # CONFIG_DVB_USB=m # CONFIG_DVB_USB_DEBUG is not set # CONFIG_DVB_USB_A800 is not set # CONFIG_DVB_USB_DIBUSB_MB is not set # CONFIG_DVB_USB_DIBUSB_MC is not set # CONFIG_DVB_USB_DIB0700 is not set # CONFIG_DVB_USB_UMT_010 is not set # CONFIG_DVB_USB_CXUSB is not set # CONFIG_DVB_USB_DIGITV is not set # CONFIG_DVB_USB_VP7045 is not set # CONFIG_DVB_USB_VP702X is not set # CONFIG_DVB_USB_GP8PSK is not set # CONFIG_DVB_USB_NOVA_T_USB2 is not set # CONFIG_DVB_USB_TTUSB2 is not set # CONFIG_DVB_USB_DTT200U is not set # CONFIG_DVB_TTUSB_BUDGET is not set # CONFIG_DVB_TTUSB_DEC is not set # CONFIG_DVB_CINERGYT2 is not set # # Supported FlexCopII (B2C2) Adapters # # CONFIG_DVB_B2C2_FLEXCOP is not set # # Supported BT878 Adapters # # # Supported Pluto2 Adapters # # CONFIG_DVB_PLUTO2 is not set # # Supported DVB Frontends # # # Customise DVB Frontends # # CONFIG_DVB_FE_CUSTOMISE is not set # # DVB-S (satellite) frontends # # CONFIG_DVB_STV0299 is not set # CONFIG_DVB_CX24110 is not set # CONFIG_DVB_CX24123 is not set # CONFIG_DVB_TDA8083 is not set # CONFIG_DVB_MT312 is not set # CONFIG_DVB_VES1X93 is not set # CONFIG_DVB_S5H1420 is not set # CONFIG_DVB_TDA10086 is not set # # DVB-T (terrestrial) frontends # # CONFIG_DVB_SP8870 is not set # CONFIG_DVB_SP887X is not set # CONFIG_DVB_CX22700 is not set # CONFIG_DVB_CX22702 is not set # CONFIG_DVB_L64781 is not set # CONFIG_DVB_TDA1004X is not set # CONFIG_DVB_NXT6000 is not set # CONFIG_DVB_MT352 is not set # CONFIG_DVB_ZL10353 is not set # CONFIG_DVB_DIB3000MB is not set # CONFIG_DVB_DIB3000MC is not set # CONFIG_DVB_DIB7000M is not set # CONFIG_DVB_DIB7000P is not set # # DVB-C (cable) frontends # # CONFIG_DVB_VES1820 is not set # CONFIG_DVB_TDA10021 is not set # CONFIG_DVB_STV0297 is not set # # ATSC (North American/Korean Terrestrial/Cable DTV) frontends # # CONFIG_DVB_NXT200X is not set # CONFIG_DVB_OR51211 is not set # CONFIG_DVB_OR51132 is not set # CONFIG_DVB_BCM3510 is not set # CONFIG_DVB_LGDT330X is not set # # Tuners/PLL support # CONFIG_DVB_PLL=m # CONFIG_DVB_TDA826X is not set # CONFIG_DVB_TUNER_MT2060 is not set # CONFIG_DVB_TUNER_LGH06XF is not set # # Miscellaneous devices # # CONFIG_DVB_LNBP21 is not set # CONFIG_DVB_ISL6421 is not set # CONFIG_DVB_TUA6100 is not set CONFIG_VIDEO_BUF=m # CONFIG_USB_DABUSB is not set # # Graphics support # # CONFIG_FIRMWARE_EDID is not set CONFIG_FB=y # CONFIG_FB_DDC is not set CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y # CONFIG_FB_MACMODES is not set # CONFIG_FB_BACKLIGHT is not set CONFIG_FB_MODE_HELPERS=y CONFIG_FB_TILEBLITTING=y # CONFIG_FB_CIRRUS is not set # CONFIG_FB_PM2 is not set # CONFIG_FB_CYBER2000 is not set # CONFIG_FB_ARC is not set # CONFIG_FB_ASILIANT is not set # CONFIG_FB_IMSTT is not set CONFIG_FB_VGA16=m CONFIG_FB_VESA=y # CONFIG_FB_HGA is not set # CONFIG_FB_S1D13XXX is not set CONFIG_FB_NVIDIA=m CONFIG_FB_NVIDIA_I2C=y # CONFIG_FB_RIVA is not set # CONFIG_FB_I810 is not set # CONFIG_FB_INTEL is not set # CONFIG_FB_MATROX is not set # CONFIG_FB_RADEON is not set # CONFIG_FB_ATY128 is not set # CONFIG_FB_ATY is not set # CONFIG_FB_SAVAGE is not set # CONFIG_FB_SIS is not set # CONFIG_FB_NEOMAGIC is not set # CONFIG_FB_KYRO is not set # CONFIG_FB_3DFX is not set # CONFIG_FB_VOODOO1 is not set # CONFIG_FB_CYBLA is not set # CONFIG_FB_TRIDENT is not set # CONFIG_FB_GEODE is not set # CONFIG_FB_VIRTUAL is not set # # Console display driver support # CONFIG_VGA_CONSOLE=y CONFIG_VGACON_SOFT_SCROLLBACK=y CONFIG_VGACON_SOFT_SCROLLBACK_SIZE=64 CONFIG_VIDEO_SELECT=y CONFIG_DUMMY_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y # CONFIG_FONTS is not set CONFIG_FONT_8x8=y CONFIG_FONT_8x16=y # # Logo configuration # CONFIG_LOGO=y # CONFIG_LOGO_LINUX_MONO is not set # CONFIG_LOGO_LINUX_VGA16 is not set CONFIG_LOGO_LINUX_CLUT224=y CONFIG_BACKLIGHT_LCD_SUPPORT=y CONFIG_BACKLIGHT_CLASS_DEVICE=m CONFIG_BACKLIGHT_DEVICE=y CONFIG_LCD_CLASS_DEVICE=m CONFIG_LCD_DEVICE=y # # Sound # CONFIG_SOUND=m # # Advanced Linux Sound Architecture # CONFIG_SND=m CONFIG_SND_TIMER=m CONFIG_SND_PCM=m CONFIG_SND_HWDEP=m CONFIG_SND_RAWMIDI=m CONFIG_SND_SEQUENCER=m CONFIG_SND_SEQ_DUMMY=m CONFIG_SND_OSSEMUL=y CONFIG_SND_MIXER_OSS=m CONFIG_SND_PCM_OSS=m CONFIG_SND_PCM_OSS_PLUGINS=y CONFIG_SND_SEQUENCER_OSS=y CONFIG_SND_RTCTIMER=m CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y CONFIG_SND_DYNAMIC_MINORS=y # CONFIG_SND_SUPPORT_OLD_API is not set CONFIG_SND_VERBOSE_PROCFS=y # CONFIG_SND_VERBOSE_PRINTK is not set # CONFIG_SND_DEBUG is not set # # Generic devices # CONFIG_SND_MPU401_UART=m CONFIG_SND_AC97_CODEC=m CONFIG_SND_DUMMY=m CONFIG_SND_VIRMIDI=m CONFIG_SND_MTPAV=m CONFIG_SND_MTS64=m # CONFIG_SND_SERIAL_U16550 is not set CONFIG_SND_MPU401=m # # PCI devices # # CONFIG_SND_AD1889 is not set # CONFIG_SND_ALS300 is not set # CONFIG_SND_ALS4000 is not set # CONFIG_SND_ALI5451 is not set # CONFIG_SND_ATIIXP is not set # CONFIG_SND_ATIIXP_MODEM is not set # CONFIG_SND_AU8810 is not set # CONFIG_SND_AU8820 is not set # CONFIG_SND_AU8830 is not set # CONFIG_SND_AZT3328 is not set # CONFIG_SND_BT87X is not set # CONFIG_SND_CA0106 is not set # CONFIG_SND_CMIPCI is not set # CONFIG_SND_CS4281 is not set # CONFIG_SND_CS46XX is not set # CONFIG_SND_CS5535AUDIO is not set # CONFIG_SND_DARLA20 is not set # CONFIG_SND_GINA20 is not set # CONFIG_SND_LAYLA20 is not set # CONFIG_SND_DARLA24 is not set # CONFIG_SND_GINA24 is not set # CONFIG_SND_LAYLA24 is not set # CONFIG_SND_MONA is not set # CONFIG_SND_MIA is not set # CONFIG_SND_ECHO3G is not set # CONFIG_SND_INDIGO is not set # CONFIG_SND_INDIGOIO is not set # CONFIG_SND_INDIGODJ is not set # CONFIG_SND_EMU10K1 is not set # CONFIG_SND_EMU10K1X is not set # CONFIG_SND_ENS1370 is not set # CONFIG_SND_ENS1371 is not set # CONFIG_SND_ES1938 is not set # CONFIG_SND_ES1968 is not set # CONFIG_SND_FM801 is not set # CONFIG_SND_HDA_INTEL is not set # CONFIG_SND_HDSP is not set # CONFIG_SND_HDSPM is not set # CONFIG_SND_ICE1712 is not set # CONFIG_SND_ICE1724 is not set # CONFIG_SND_INTEL8X0 is not set # CONFIG_SND_INTEL8X0M is not set # CONFIG_SND_KORG1212 is not set # CONFIG_SND_MAESTRO3 is not set # CONFIG_SND_MIXART is not set # CONFIG_SND_NM256 is not set # CONFIG_SND_PCXHR is not set # CONFIG_SND_RIPTIDE is not set # CONFIG_SND_RME32 is not set # CONFIG_SND_RME96 is not set # CONFIG_SND_RME9652 is not set # CONFIG_SND_SONICVIBES is not set # CONFIG_SND_TRIDENT is not set CONFIG_SND_VIA82XX=m # CONFIG_SND_VIA82XX_MODEM is not set # CONFIG_SND_VX222 is not set # CONFIG_SND_YMFPCI is not set CONFIG_SND_AC97_POWER_SAVE=y # # USB devices # CONFIG_SND_USB_AUDIO=m CONFIG_SND_USB_USX2Y=m # # Open Sound System # # CONFIG_SOUND_PRIME is not set CONFIG_AC97_BUS=m # # HID Devices # CONFIG_HID=y # # USB support # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y CONFIG_USB_ARCH_HAS_EHCI=y CONFIG_USB=y # CONFIG_USB_DEBUG is not set # # Miscellaneous USB options # CONFIG_USB_DEVICEFS=y # CONFIG_USB_BANDWIDTH is not set # CONFIG_USB_DYNAMIC_MINORS is not set # CONFIG_USB_SUSPEND is not set # CONFIG_USB_OTG is not set # # USB Host Controller Drivers # CONFIG_USB_EHCI_HCD=m CONFIG_USB_EHCI_SPLIT_ISO=y CONFIG_USB_EHCI_ROOT_HUB_TT=y CONFIG_USB_EHCI_TT_NEWSCHED=y # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_OHCI_HCD is not set CONFIG_USB_UHCI_HCD=m # CONFIG_USB_SL811_HCD is not set # # USB Device Class drivers # # CONFIG_USB_ACM is not set CONFIG_USB_PRINTER=m # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' # # # may also be needed; see USB_STORAGE Help for more information # CONFIG_USB_STORAGE=m # CONFIG_USB_STORAGE_DEBUG is not set CONFIG_USB_STORAGE_DATAFAB=y CONFIG_USB_STORAGE_FREECOM=y CONFIG_USB_STORAGE_ISD200=y CONFIG_USB_STORAGE_DPCM=y CONFIG_USB_STORAGE_USBAT=y CONFIG_USB_STORAGE_SDDR09=y CONFIG_USB_STORAGE_SDDR55=y CONFIG_USB_STORAGE_JUMPSHOT=y # CONFIG_USB_STORAGE_ALAUDA is not set # CONFIG_USB_STORAGE_KARMA is not set CONFIG_USB_LIBUSUAL=y # # USB Input Devices # CONFIG_USB_HID=y # CONFIG_USB_HIDINPUT_POWERBOOK is not set # CONFIG_HID_FF is not set CONFIG_USB_HIDDEV=y # CONFIG_USB_AIPTEK is not set # CONFIG_USB_WACOM is not set # CONFIG_USB_ACECAD is not set # CONFIG_USB_KBTAB is not set # CONFIG_USB_POWERMATE is not set CONFIG_USB_TOUCHSCREEN=m CONFIG_USB_TOUCHSCREEN_EGALAX=y CONFIG_USB_TOUCHSCREEN_PANJIT=y CONFIG_USB_TOUCHSCREEN_3M=y CONFIG_USB_TOUCHSCREEN_ITM=y CONFIG_USB_TOUCHSCREEN_ETURBO=y CONFIG_USB_TOUCHSCREEN_GUNZE=y CONFIG_USB_TOUCHSCREEN_DMC_TSC10=y # CONFIG_USB_YEALINK is not set # CONFIG_USB_XPAD is not set # CONFIG_USB_ATI_REMOTE is not set # CONFIG_USB_ATI_REMOTE2 is not set # CONFIG_USB_KEYSPAN_REMOTE is not set # CONFIG_USB_APPLETOUCH is not set # # USB Imaging devices # # CONFIG_USB_MDC800 is not set # CONFIG_USB_MICROTEK is not set # # USB Network Adapters # # CONFIG_USB_CATC is not set # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set # CONFIG_USB_USBNET_MII is not set # CONFIG_USB_USBNET is not set CONFIG_USB_MON=y # # USB port drivers # # CONFIG_USB_USS720 is not set # # USB Serial Converter support # # CONFIG_USB_SERIAL is not set # # USB Miscellaneous drivers # # CONFIG_USB_EMI62 is not set # CONFIG_USB_EMI26 is not set # CONFIG_USB_ADUTUX is not set # CONFIG_USB_AUERSWALD is not set # CONFIG_USB_RIO500 is not set # CONFIG_USB_LEGOTOWER is not set # CONFIG_USB_LCD is not set # CONFIG_USB_LED is not set # CONFIG_USB_CYPRESS_CY7C63 is not set # CONFIG_USB_CYTHERM is not set # CONFIG_USB_PHIDGET is not set # CONFIG_USB_IDMOUSE is not set # CONFIG_USB_FTDI_ELAN is not set # CONFIG_USB_APPLEDISPLAY is not set # CONFIG_USB_SISUSBVGA is not set # CONFIG_USB_LD is not set # CONFIG_USB_TRANCEVIBRATOR is not set # CONFIG_USB_TEST is not set # # USB DSL modem support # # # USB Gadget Support # # CONFIG_USB_GADGET is not set # # MMC/SD Card support # # CONFIG_MMC is not set # # LED devices # # CONFIG_NEW_LEDS is not set # # LED drivers # # # LED Triggers # # # InfiniBand support # # CONFIG_INFINIBAND is not set # # EDAC - error detection and reporting (RAS) (EXPERIMENTAL) # # CONFIG_EDAC is not set # # Real Time Clock # CONFIG_RTC_LIB=m CONFIG_RTC_CLASS=m # # RTC interfaces # CONFIG_RTC_INTF_SYSFS=m CONFIG_RTC_INTF_PROC=m CONFIG_RTC_INTF_DEV=m # CONFIG_RTC_INTF_DEV_UIE_EMUL is not set # # RTC drivers # CONFIG_RTC_DRV_X1205=m CONFIG_RTC_DRV_DS1307=m CONFIG_RTC_DRV_DS1553=m CONFIG_RTC_DRV_ISL1208=m # CONFIG_RTC_DRV_DS1672 is not set # CONFIG_RTC_DRV_DS1742 is not set # CONFIG_RTC_DRV_PCF8563 is not set # CONFIG_RTC_DRV_PCF8583 is not set # CONFIG_RTC_DRV_RS5C372 is not set # CONFIG_RTC_DRV_M48T86 is not set # CONFIG_RTC_DRV_TEST is not set # CONFIG_RTC_DRV_V3020 is not set # # DMA Engine support # CONFIG_DMA_ENGINE=y # # DMA Clients # CONFIG_NET_DMA=y # # DMA Devices # CONFIG_INTEL_IOATDMA=m # # Virtualization # # CONFIG_KVM is not set # # File systems # CONFIG_EXT2_FS=y CONFIG_EXT2_FS_XATTR=y CONFIG_EXT2_FS_POSIX_ACL=y CONFIG_EXT2_FS_SECURITY=y CONFIG_EXT2_FS_XIP=y CONFIG_FS_XIP=y CONFIG_EXT3_FS=y CONFIG_EXT3_FS_XATTR=y CONFIG_EXT3_FS_POSIX_ACL=y CONFIG_EXT3_FS_SECURITY=y # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y # CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y # CONFIG_XFS_FS is not set # CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_MINIX_FS is not set CONFIG_ROMFS_FS=m CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y CONFIG_QUOTA=y # CONFIG_QFMT_V1 is not set CONFIG_QFMT_V2=y CONFIG_QUOTACTL=y CONFIG_DNOTIFY=y CONFIG_AUTOFS_FS=m CONFIG_AUTOFS4_FS=m CONFIG_FUSE_FS=m CONFIG_GENERIC_ACL=y # # CD-ROM/DVD Filesystems # CONFIG_ISO9660_FS=y CONFIG_JOLIET=y CONFIG_ZISOFS=y CONFIG_ZISOFS_FS=y CONFIG_UDF_FS=m CONFIG_UDF_NLS=y # # DOS/FAT/NT Filesystems # CONFIG_FAT_FS=m CONFIG_MSDOS_FS=m CONFIG_VFAT_FS=m CONFIG_FAT_DEFAULT_CODEPAGE=437 CONFIG_FAT_DEFAULT_IOCHARSET="ascii" CONFIG_NTFS_FS=m # CONFIG_NTFS_DEBUG is not set # CONFIG_NTFS_RW is not set # # Pseudo filesystems # CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y CONFIG_SYSFS=y CONFIG_TMPFS=y CONFIG_TMPFS_POSIX_ACL=y CONFIG_HUGETLBFS=y CONFIG_HUGETLB_PAGE=y CONFIG_RAMFS=y CONFIG_CONFIGFS_FS=m # # Miscellaneous filesystems # # CONFIG_ADFS_FS is not set # CONFIG_AFFS_FS is not set CONFIG_ECRYPT_FS=m # CONFIG_HFS_FS is not set # CONFIG_HFSPLUS_FS is not set # CONFIG_BEFS_FS is not set # CONFIG_BFS_FS is not set # CONFIG_EFS_FS is not set CONFIG_CRAMFS=m # CONFIG_VXFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set # # Network File Systems # CONFIG_NFS_FS=m CONFIG_NFS_V3=y CONFIG_NFS_V3_ACL=y CONFIG_NFS_V4=y CONFIG_NFS_DIRECTIO=y CONFIG_NFSD=m CONFIG_NFSD_V2_ACL=y CONFIG_NFSD_V3=y CONFIG_NFSD_V3_ACL=y CONFIG_NFSD_V4=y CONFIG_NFSD_TCP=y CONFIG_LOCKD=m CONFIG_LOCKD_V4=y CONFIG_EXPORTFS=m CONFIG_NFS_ACL_SUPPORT=m CONFIG_NFS_COMMON=y CONFIG_SUNRPC=m CONFIG_SUNRPC_GSS=m CONFIG_RPCSEC_GSS_KRB5=m CONFIG_RPCSEC_GSS_SPKM3=m # CONFIG_SMB_FS is not set CONFIG_CIFS=m # CONFIG_CIFS_STATS is not set CONFIG_CIFS_WEAK_PW_HASH=y CONFIG_CIFS_XATTR=y CONFIG_CIFS_POSIX=y # CONFIG_CIFS_DEBUG2 is not set # CONFIG_CIFS_EXPERIMENTAL is not set # CONFIG_NCP_FS is not set # CONFIG_CODA_FS is not set # CONFIG_AFS_FS is not set # CONFIG_9P_FS is not set # # Partition Types # CONFIG_PARTITION_ADVANCED=y # CONFIG_ACORN_PARTITION is not set # CONFIG_OSF_PARTITION is not set # CONFIG_AMIGA_PARTITION is not set # CONFIG_ATARI_PARTITION is not set # CONFIG_MAC_PARTITION is not set CONFIG_MSDOS_PARTITION=y # CONFIG_BSD_DISKLABEL is not set # CONFIG_MINIX_SUBPARTITION is not set # CONFIG_SOLARIS_X86_PARTITION is not set # CONFIG_UNIXWARE_DISKLABEL is not set # CONFIG_LDM_PARTITION is not set # CONFIG_SGI_PARTITION is not set # CONFIG_ULTRIX_PARTITION is not set # CONFIG_SUN_PARTITION is not set # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # # Native Language Support # CONFIG_NLS=y CONFIG_NLS_DEFAULT="utf8" CONFIG_NLS_CODEPAGE_437=y CONFIG_NLS_CODEPAGE_737=m CONFIG_NLS_CODEPAGE_775=m CONFIG_NLS_CODEPAGE_850=m CONFIG_NLS_CODEPAGE_852=y CONFIG_NLS_CODEPAGE_855=m # CONFIG_NLS_CODEPAGE_857 is not set CONFIG_NLS_CODEPAGE_860=m CONFIG_NLS_CODEPAGE_861=m CONFIG_NLS_CODEPAGE_862=m CONFIG_NLS_CODEPAGE_863=m CONFIG_NLS_CODEPAGE_864=m CONFIG_NLS_CODEPAGE_865=m CONFIG_NLS_CODEPAGE_866=m CONFIG_NLS_CODEPAGE_869=m # CONFIG_NLS_CODEPAGE_936 is not set # CONFIG_NLS_CODEPAGE_950 is not set # CONFIG_NLS_CODEPAGE_932 is not set # CONFIG_NLS_CODEPAGE_949 is not set # CONFIG_NLS_CODEPAGE_874 is not set CONFIG_NLS_ISO8859_8=m CONFIG_NLS_CODEPAGE_1250=m CONFIG_NLS_CODEPAGE_1251=m CONFIG_NLS_ASCII=y CONFIG_NLS_ISO8859_1=m CONFIG_NLS_ISO8859_2=m CONFIG_NLS_ISO8859_3=m CONFIG_NLS_ISO8859_4=m CONFIG_NLS_ISO8859_5=m CONFIG_NLS_ISO8859_6=m CONFIG_NLS_ISO8859_7=m CONFIG_NLS_ISO8859_9=m CONFIG_NLS_ISO8859_13=m CONFIG_NLS_ISO8859_14=m CONFIG_NLS_ISO8859_15=m # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set CONFIG_NLS_UTF8=m # # Distributed Lock Manager # # CONFIG_DLM is not set # # Instrumentation Support # CONFIG_PROFILING=y CONFIG_OPROFILE=m CONFIG_PROFILE_NMI=y CONFIG_KPROBES=y # # Kernel hacking # CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_PRINTK_TIME=y # CONFIG_ENABLE_MUST_CHECK is not set CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set CONFIG_DEBUG_FS=y # CONFIG_HEADERS_CHECK is not set CONFIG_DEBUG_KERNEL=y CONFIG_LOG_BUF_SHIFT=17 CONFIG_DETECT_SOFTLOCKUP=y # CONFIG_SCHEDSTATS is not set # CONFIG_TIMER_STATS is not set # CONFIG_DEBUG_SLAB is not set # CONFIG_DEBUG_PREEMPT is not set # CONFIG_DEBUG_RT_MUTEXES is not set # CONFIG_RT_MUTEX_TESTER is not set CONFIG_DEBUG_SPINLOCK=y CONFIG_DEBUG_MUTEXES=y CONFIG_DEBUG_RWSEMS=y CONFIG_DEBUG_LOCK_ALLOC=y CONFIG_PROVE_LOCKING=y CONFIG_LOCKDEP=y CONFIG_DEBUG_LOCKDEP=y CONFIG_TRACE_IRQFLAGS=y # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set CONFIG_STACKTRACE=y CONFIG_EVENT_TRACE=y CONFIG_FUNCTION_TRACE=y CONFIG_WAKEUP_TIMING=y CONFIG_LATENCY_TRACE=y CONFIG_CRITICAL_PREEMPT_TIMING=y CONFIG_CRITICAL_IRQSOFF_TIMING=y CONFIG_WAKEUP_LATENCY_HIST=y CONFIG_PREEMPT_OFF_HIST=y CONFIG_INTERRUPT_OFF_HIST=y CONFIG_CRITICAL_TIMING=y CONFIG_DEBUG_TRACE_IRQFLAGS=y CONFIG_LATENCY_TIMING=y CONFIG_CRITICAL_LATENCY_HIST=y CONFIG_LATENCY_HIST=y CONFIG_MCOUNT=y # CONFIG_DEBUG_KOBJECT is not set # CONFIG_DEBUG_HIGHMEM is not set CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set CONFIG_FRAME_POINTER=y # CONFIG_UNWIND_INFO is not set # CONFIG_FORCED_INLINING is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_LKDTM is not set # CONFIG_FAULT_INJECTION is not set CONFIG_EARLY_PRINTK=y # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # # Page alloc debug is incompatible with Software Suspend on i386 # CONFIG_DEBUG_RODATA=y # CONFIG_4KSTACKS is not set CONFIG_X86_FIND_SMP_CONFIG=y CONFIG_X86_MPPARSE=y CONFIG_DOUBLEFAULT=y # # Security options # CONFIG_KEYS=y CONFIG_KEYS_DEBUG_PROC_KEYS=y CONFIG_SECURITY=y CONFIG_SECURITY_NETWORK=y # CONFIG_SECURITY_NETWORK_XFRM is not set CONFIG_SECURITY_CAPABILITIES=y # CONFIG_REALTIME_CAPABILITIES is not set CONFIG_SECURITY_ROOTPLUG=y # CONFIG_SECURITY_SELINUX is not set # # Cryptographic options # CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=m CONFIG_CRYPTO_HASH=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_HMAC=y # CONFIG_CRYPTO_XCBC is not set CONFIG_CRYPTO_NULL=m CONFIG_CRYPTO_MD4=m CONFIG_CRYPTO_MD5=m CONFIG_CRYPTO_SHA1=y CONFIG_CRYPTO_SHA256=m CONFIG_CRYPTO_SHA512=m CONFIG_CRYPTO_WP512=m CONFIG_CRYPTO_TGR192=m # CONFIG_CRYPTO_GF128MUL is not set CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_CBC=m # CONFIG_CRYPTO_LRW is not set CONFIG_CRYPTO_DES=m CONFIG_CRYPTO_BLOWFISH=m CONFIG_CRYPTO_TWOFISH=m CONFIG_CRYPTO_TWOFISH_COMMON=m # CONFIG_CRYPTO_TWOFISH_586 is not set CONFIG_CRYPTO_SERPENT=m CONFIG_CRYPTO_AES=m # CONFIG_CRYPTO_AES_586 is not set CONFIG_CRYPTO_CAST5=m CONFIG_CRYPTO_CAST6=m CONFIG_CRYPTO_TEA=m CONFIG_CRYPTO_ARC4=m CONFIG_CRYPTO_KHAZAD=m CONFIG_CRYPTO_ANUBIS=m CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_MICHAEL_MIC=m CONFIG_CRYPTO_CRC32C=y # CONFIG_CRYPTO_TEST is not set # # Hardware crypto devices # CONFIG_CRYPTO_DEV_PADLOCK=m CONFIG_CRYPTO_DEV_PADLOCK_AES=m CONFIG_CRYPTO_DEV_PADLOCK_SHA=m # CONFIG_CRYPTO_DEV_GEODE is not set # # Library routines # CONFIG_BITREVERSE=y CONFIG_CRC_CCITT=m CONFIG_CRC16=m CONFIG_CRC32=y CONFIG_LIBCRC32C=y CONFIG_AUDIT_GENERIC=y CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=m CONFIG_TEXTSEARCH=y CONFIG_TEXTSEARCH_KMP=m CONFIG_TEXTSEARCH_BM=m CONFIG_TEXTSEARCH_FSM=m CONFIG_PLIST=y CONFIG_IOMAP_COPY=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_X86_BIOS_REBOOT=y CONFIG_KTIME_SCALAR=y ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: 2.6.20-rc6-mm3 2007-02-01 10:44 ` 2.6.20-rc6-mm3 Karsten Wiese @ 2007-02-01 11:12 ` Karsten Wiese 2007-02-01 11:12 ` 2.6.20-rc6-mm3 Karsten Wiese 1 sibling, 0 replies; 19+ messages in thread From: Karsten Wiese @ 2007-02-01 11:12 UTC (permalink / raw) To: Ingo Molnar; +Cc: Andrew Morton, Maciej Rutecki, linux-kernel, linux-acpi Am Donnerstag, 1. Februar 2007 11:44 schrieb Karsten Wiese: > I think the wait is caused by an interrupt starting somewhere under > sysdev_resume(void). > possibly lapic timer interrupt? Will try to trace that. Some evidence: [root@a64 Desktop]# echo reboot > /sys/power/disk [root@a64 Desktop]# cat /proc/interrupts; echo disk > /sys/power/state ; cat /proc/interrupts <snip> LOC: 2215504 <snip, cmos clock untouched> LOC: 2216432 <snip> [root@a64 Desktop]# cat /proc/interrupts; echo disk > /sys/power/state ; cat /proc/interrupts <snip> LOC: 2225752 <snip, cmos clock advanced by 1 month under biossettings> LOC: 2238383 <snip> Karsten ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: 2.6.20-rc6-mm3 2007-02-01 10:44 ` 2.6.20-rc6-mm3 Karsten Wiese 2007-02-01 11:12 ` 2.6.20-rc6-mm3 Karsten Wiese @ 2007-02-01 11:12 ` Karsten Wiese 1 sibling, 0 replies; 19+ messages in thread From: Karsten Wiese @ 2007-02-01 11:12 UTC (permalink / raw) To: Ingo Molnar; +Cc: Andrew Morton, Maciej Rutecki, linux-kernel, linux-acpi Am Donnerstag, 1. Februar 2007 11:44 schrieb Karsten Wiese: > I think the wait is caused by an interrupt starting somewhere under > sysdev_resume(void). > possibly lapic timer interrupt? Will try to trace that. Some evidence: [root@a64 Desktop]# echo reboot > /sys/power/disk [root@a64 Desktop]# cat /proc/interrupts; echo disk > /sys/power/state ; cat /proc/interrupts <snip> LOC: 2215504 <snip, cmos clock untouched> LOC: 2216432 <snip> [root@a64 Desktop]# cat /proc/interrupts; echo disk > /sys/power/state ; cat /proc/interrupts <snip> LOC: 2225752 <snip, cmos clock advanced by 1 month under biossettings> LOC: 2238383 <snip> Karsten ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: 2.6.20-rc6-mm3 2007-02-01 8:01 ` 2.6.20-rc6-mm3 Ingo Molnar 2007-02-01 10:44 ` 2.6.20-rc6-mm3 Karsten Wiese @ 2007-02-03 0:37 ` Pavel Machek 1 sibling, 0 replies; 19+ messages in thread From: Pavel Machek @ 2007-02-03 0:37 UTC (permalink / raw) To: Ingo Molnar Cc: Karsten Wiese, Andrew Morton, Maciej Rutecki, linux-kernel, linux-acpi Hi! > * Karsten Wiese <fzu@wemgehoertderstaat.de> wrote: > > > Serial port console is off here and the jiffies update fix doesn't > > make a noticeable difference. > > ok, this eliminates my serial port theory. > > and this means i'm having trouble reproducing this problem locally. > Maybe i tried it the wrong way: does it only occur with suspend-to-disk, > or suspend-to-ram too? Does it need ACPI suspend-to-disk, or > software-suspend? ? What is ACPI suspend-to-disk? There used to be S4bios *long* time ago... these days everyone does swsusp. (Granted, you can select "shutdown" and "platform" flavours...) Pavel -- (english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html ^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH -mm] gtod persistent clock resume fix 2007-01-31 0:55 ` 2.6.20-rc6-mm3 Karsten Wiese 2007-01-31 13:22 ` 2.6.20-rc6-mm3 Ingo Molnar @ 2007-02-01 13:03 ` Thomas Gleixner 1 sibling, 0 replies; 19+ messages in thread From: Thomas Gleixner @ 2007-02-01 13:03 UTC (permalink / raw) To: Karsten Wiese; +Cc: Andrew Morton, Maciej Rutecki, linux-kernel, linux-acpi The reworked highres/dyntick code made a thinko in the resume code visible, which was magically working in the old queue. On resume we add the slept time to xtime. This delta must be adjusted in wall_to_monotonic as well. The update of jiffies64 is bogus and a leftover of the code which was taken from arch/i386/kernel/time.c. On suspend the current state of xtime, wall_to_monotonic and jiffies is frozen. After resume we need to add the slept time to xtime, but we need to subtract it from wall_to_monotonic, so the monotonic time is resuming from exactly the point where it was suspended. jiffies are restarting from the same point as well. This solves the resume waittime observed by Karsten Wiese. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Index: linux-2.6.20-rc6-mm/kernel/timer.c =================================================================== --- linux-2.6.20-rc6-mm.orig/kernel/timer.c +++ linux-2.6.20-rc6-mm/kernel/timer.c @@ -985,8 +985,9 @@ static int timekeeping_resume(struct sys if (now && (now > timekeeping_suspend_time)) { unsigned long sleep_length = now - timekeeping_suspend_time; + xtime.tv_sec += sleep_length; - jiffies_64 += (u64)sleep_length * HZ; + wall_to_monotonic.tv_sec -= sleep_length; } /* re-base the last cycle value */ clock->cycle_last = clocksource_read(clock); @@ -994,7 +995,7 @@ static int timekeeping_resume(struct sys timekeeping_suspended = 0; write_sequnlock_irqrestore(&xtime_lock, flags); - clockevents_notify(CLOCK_EVT_NOTIFY_RESUME, NULL); + touch_softlockup_watchdog(); /* Resume hrtimers */ clock_was_set(); ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: 2.6.20-rc6-mm3 2007-01-30 22:27 ` 2.6.20-rc6-mm3 Andrew Morton 2007-01-31 0:55 ` 2.6.20-rc6-mm3 Karsten Wiese @ 2007-01-31 11:54 ` Maciej Rutecki 2007-02-01 4:10 ` 2.6.20-rc6-mm3 Len Brown 1 sibling, 1 reply; 19+ messages in thread From: Maciej Rutecki @ 2007-01-31 11:54 UTC (permalink / raw) To: Andrew Morton; +Cc: linux-kernel, linux-acpi [-- Attachment #1.1: Type: text/plain, Size: 1515 bytes --] Andrew Morton napisał(a): > OK, thanks. That might be due to the time-management updates as well. > I'll see if I can reproduce this. > > If you're keen, you could test just 2.6.19-rc6+origin.patch+git-acpi.patch > from > ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.20-rc6/2.6.20-rc6-mm3/broken-out > and see which of these problems remain. > I try 2.6.19-rc6 witch origin.patch and git-acpi.patch. This patch didn't add correctly (see patch_output.txt). Also I have compiling error: AS arch/i386/kernel/entry.o CC arch/i386/kernel/traps.o CC arch/i386/kernel/irq.o CC arch/i386/kernel/ptrace.o CC arch/i386/kernel/time.o CC arch/i386/kernel/ioport.o CC arch/i386/kernel/ldt.o CC arch/i386/kernel/setup.o In file included from include/acpi/acpi.h:62, from include/linux/acpi.h:37, from arch/i386/kernel/setup.c:31: include/acpi/acpixf.h:100: warning: 'struct acpi_pointer' declared inside parameter list include/acpi/acpixf.h:100: warning: its scope is only this definition or declaration, which is probably not what you want include/acpi/acpixf.h:115: error: expected ')' before 'table_type' make[2]: *** [arch/i386/kernel/setup.o] Błąd 1 make[1]: *** [arch/i386/kernel] Błąd 2 make[1]: Opuszczenie katalogu `/usr/src/linux-rc' make: *** [debian/stamp-build-kernel] Błąd 2 "Błąd"="Error" (in polish). -- Maciej Rutecki <maciej.rutecki@gmail.com> [-- Attachment #1.2: patch_output.txt.gz --] [-- Type: application/x-gzip, Size: 4881 bytes --] [-- Attachment #2: S/MIME Cryptographic Signature --] [-- Type: application/x-pkcs7-signature, Size: 3265 bytes --] ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: 2.6.20-rc6-mm3 2007-01-31 11:54 ` 2.6.20-rc6-mm3 Maciej Rutecki @ 2007-02-01 4:10 ` Len Brown 2007-02-01 4:17 ` 2.6.20-rc6-mm3 Andrew Morton 0 siblings, 1 reply; 19+ messages in thread From: Len Brown @ 2007-02-01 4:10 UTC (permalink / raw) To: Maciej Rutecki; +Cc: Andrew Morton, linux-kernel, linux-acpi On Wednesday 31 January 2007 06:54, Maciej Rutecki wrote: > Andrew Morton napisał(a): > > > OK, thanks. That might be due to the time-management updates as well. > > I'll see if I can reproduce this. > > > > If you're keen, you could test just 2.6.19-rc6+origin.patch+git-acpi.patch > > from > > ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.20-rc6/2.6.20-rc6-mm3/broken-out > > and see which of these problems remain. > > > > I try 2.6.19-rc6 witch origin.patch and git-acpi.patch. This patch > didn't add correctly (see patch_output.txt). Also I have compiling error: > > AS arch/i386/kernel/entry.o > CC arch/i386/kernel/traps.o > CC arch/i386/kernel/irq.o > CC arch/i386/kernel/ptrace.o > CC arch/i386/kernel/time.o > CC arch/i386/kernel/ioport.o > CC arch/i386/kernel/ldt.o > CC arch/i386/kernel/setup.o > In file included from include/acpi/acpi.h:62, > from include/linux/acpi.h:37, > from arch/i386/kernel/setup.c:31: > include/acpi/acpixf.h:100: warning: 'struct acpi_pointer' declared > inside parameter list > include/acpi/acpixf.h:100: warning: its scope is only this definition or > declaration, which is probably not what you want > include/acpi/acpixf.h:115: error: expected ')' before 'table_type' > make[2]: *** [arch/i386/kernel/setup.o] Błąd 1 > make[1]: *** [arch/i386/kernel] Błąd 2 > make[1]: Opuszczenie katalogu `/usr/src/linux-rc' > make: *** [debian/stamp-build-kernel] Błąd 2 > > "Błąd"="Error" (in polish). Note that you can always get the latest ACPI patch and drop it directly onto Linus' tree here: http://ftp.kernel.org/pub/linux/kernel/people/lenb/acpi/patches/test/2.6.20/ - To unsubscribe from this list: send the line "unsubscribe linux-acpi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: 2.6.20-rc6-mm3 2007-02-01 4:10 ` 2.6.20-rc6-mm3 Len Brown @ 2007-02-01 4:17 ` Andrew Morton 0 siblings, 0 replies; 19+ messages in thread From: Andrew Morton @ 2007-02-01 4:17 UTC (permalink / raw) To: Len Brown; +Cc: Maciej Rutecki, linux-kernel, linux-acpi On Wed, 31 Jan 2007 23:10:32 -0500 Len Brown <lenb@kernel.org> wrote: > > CC arch/i386/kernel/traps.o > > CC arch/i386/kernel/irq.o > > CC arch/i386/kernel/ptrace.o > > CC arch/i386/kernel/time.o > > CC arch/i386/kernel/ioport.o > > CC arch/i386/kernel/ldt.o > > CC arch/i386/kernel/setup.o > > In file included from include/acpi/acpi.h:62, > > from include/linux/acpi.h:37, > > from arch/i386/kernel/setup.c:31: > > include/acpi/acpixf.h:100: warning: 'struct acpi_pointer' declared > > inside parameter list > > include/acpi/acpixf.h:100: warning: its scope is only this definition or > > declaration, which is probably not what you want > > include/acpi/acpixf.h:115: error: expected ')' before 'table_type' > > make[2]: *** [arch/i386/kernel/setup.o] Błąd 1 > > make[1]: *** [arch/i386/kernel] Błąd 2 > > make[1]: Opuszczenie katalogu `/usr/src/linux-rc' > > make: *** [debian/stamp-build-kernel] Błąd 2 > > > > "Błąd"="Error" (in polish). > > Note that you can always get the latest ACPI patch and drop it directly onto Linus' tree here: > http://ftp.kernel.org/pub/linux/kernel/people/lenb/acpi/patches/test/2.6.20/ I'm suspecting that Maciej misapplied the -mm patch somehow: box:/usr/src/foo> grep acpi_pointer include/acpi/acpixf.h box:/usr/src/foo> - To unsubscribe from this list: send the line "unsubscribe linux-acpi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 19+ messages in thread
[parent not found: <45BFEDFB.6000500@imap.cc>]
* Re: 2.6.20-rc6-mm3 [not found] ` <45BFEDFB.6000500@imap.cc> @ 2007-01-31 1:25 ` Andrew Morton 2007-01-31 11:38 ` 2.6.20-rc6-mm3 Tilman Schmidt 0 siblings, 1 reply; 19+ messages in thread From: Andrew Morton @ 2007-01-31 1:25 UTC (permalink / raw) To: Tilman Schmidt; +Cc: Maciej Rutecki, linux-kernel, linux-acpi On Wed, 31 Jan 2007 02:16:43 +0100 Tilman Schmidt <tilman@imap.cc> wrote: > Am 30.01.2007 23:18 schrieb Maciej Rutecki: > > Second problem, power button doesn't work. When I pressed it, I has this > > error: > > > > ACPI Error (evevent-0305): No installed handler for fixed event > > [00000002] [20070126] > > Same here, minus the message. (Or perhaps I just don't know where to look.) > Problem also exists in 2.6.20-rc6-mm2. With 2.6.20-rc6-git1 the power > button of this machine works fine. > That's significant - in your case at least the 2.6.20-rc6-mm3 ACPI update isn't the cause. ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: 2.6.20-rc6-mm3 2007-01-31 1:25 ` 2.6.20-rc6-mm3 Andrew Morton @ 2007-01-31 11:38 ` Tilman Schmidt 2007-01-31 12:29 ` 2.6.20-rc6-mm3 Alexey Starikovskiy 0 siblings, 1 reply; 19+ messages in thread From: Tilman Schmidt @ 2007-01-31 11:38 UTC (permalink / raw) To: Andrew Morton; +Cc: Maciej Rutecki, linux-kernel, linux-acpi [-- Attachment #1: Type: text/plain, Size: 948 bytes --] On Tue, 30 Jan 2007 17:25:25 -0800, Andrew Morton wrote: > On Wed, 31 Jan 2007 02:16:43 +0100 > Tilman Schmidt <tilman@imap.cc> wrote: > >> Am 30.01.2007 23:18 schrieb Maciej Rutecki: >> > Second problem, power button doesn't work. When I pressed it, I has this >> > error: >> > >> > ACPI Error (evevent-0305): No installed handler for fixed event >> > [00000002] [20070126] >> >> Same here, minus the message. (Or perhaps I just don't know where to look.) >> Problem also exists in 2.6.20-rc6-mm2. With 2.6.20-rc6-git1 the power >> button of this machine works fine. > > That's significant - in your case at least the 2.6.20-rc6-mm3 ACPI update > isn't the cause. Is there anything specific I should test, or Big Bisect time? -- Tilman Schmidt E-Mail: tilman@imap.cc Bonn, Germany Diese Nachricht besteht zu 100% aus wiederverwerteten Bits. Ungeöffnet mindestens haltbar bis: (siehe Rückseite) [-- Attachment #2: OpenPGP digital signature --] [-- Type: application/pgp-signature, Size: 250 bytes --] ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: 2.6.20-rc6-mm3 2007-01-31 11:38 ` 2.6.20-rc6-mm3 Tilman Schmidt @ 2007-01-31 12:29 ` Alexey Starikovskiy 2007-01-31 16:02 ` 2.6.20-rc6-mm3 Maciej Rutecki 2007-01-31 18:28 ` 2.6.20-rc6-mm3 Tilman Schmidt 0 siblings, 2 replies; 19+ messages in thread From: Alexey Starikovskiy @ 2007-01-31 12:29 UTC (permalink / raw) To: Tilman Schmidt; +Cc: Andrew Morton, Maciej Rutecki, linux-kernel, linux-acpi [-- Attachment #1: Type: text/plain, Size: 878 bytes --] Tilman Schmidt wrote: > On Tue, 30 Jan 2007 17:25:25 -0800, Andrew Morton wrote: > >> On Wed, 31 Jan 2007 02:16:43 +0100 >> Tilman Schmidt <tilman@imap.cc> wrote: >> >> >>> Am 30.01.2007 23:18 schrieb Maciej Rutecki: >>> >>>> Second problem, power button doesn't work. When I pressed it, I has this >>>> error: >>>> >>>> ACPI Error (evevent-0305): No installed handler for fixed event >>>> [00000002] [20070126] >>>> >>> Same here, minus the message. (Or perhaps I just don't know where to look.) >>> Problem also exists in 2.6.20-rc6-mm2. With 2.6.20-rc6-git1 the power >>> button of this machine works fine. >>> >> That's significant - in your case at least the 2.6.20-rc6-mm3 ACPI update >> isn't the cause. >> > > Is there anything specific I should test, or Big Bisect time? > > This patch should fix the issue... Regards, Alex. [-- Attachment #2: fix-button_c.patch --] [-- Type: text/plain, Size: 835 bytes --] Correct id for fixed buttons. ACPI_BUTTON_HID_POWERF was changed, but this change was not propogated to button.c, thus breaking detection of fixed power and sleep buttons. From: Alexey Starikovskiy <alexey.y.starikovskiy@linux.intel.com> --- drivers/acpi/button.c | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-) diff --git a/drivers/acpi/button.c b/drivers/acpi/button.c index ac86058..c726612 100644 --- a/drivers/acpi/button.c +++ b/drivers/acpi/button.c @@ -75,7 +75,7 @@ static int acpi_button_state_open_fs(str static struct acpi_driver acpi_button_driver = { .name = ACPI_BUTTON_DRIVER_NAME, .class = ACPI_BUTTON_CLASS, - .ids = "ACPI_FPB,ACPI_FSB,PNP0C0D,PNP0C0C,PNP0C0E", + .ids = "button_power,button_sleep,PNP0C0D,PNP0C0C,PNP0C0E", .ops = { .add = acpi_button_add, .remove = acpi_button_remove, ^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: 2.6.20-rc6-mm3 2007-01-31 12:29 ` 2.6.20-rc6-mm3 Alexey Starikovskiy @ 2007-01-31 16:02 ` Maciej Rutecki 2007-01-31 18:28 ` 2.6.20-rc6-mm3 Tilman Schmidt 1 sibling, 0 replies; 19+ messages in thread From: Maciej Rutecki @ 2007-01-31 16:02 UTC (permalink / raw) To: Alexey Starikovskiy Cc: Tilman Schmidt, Andrew Morton, linux-kernel, linux-acpi [-- Attachment #1: Type: text/plain, Size: 1076 bytes --] Alexey Starikovskiy napisał(a): > Tilman Schmidt wrote: >> On Tue, 30 Jan 2007 17:25:25 -0800, Andrew Morton wrote: >> >>> On Wed, 31 Jan 2007 02:16:43 +0100 >>> Tilman Schmidt <tilman@imap.cc> wrote: >>> >>> >>>> Am 30.01.2007 23:18 schrieb Maciej Rutecki: >>>> >>>>> Second problem, power button doesn't work. When I pressed it, I has >>>>> this >>>>> error: >>>>> >>>>> ACPI Error (evevent-0305): No installed handler for fixed event >>>>> [00000002] [20070126] >>>>> >>>> Same here, minus the message. (Or perhaps I just don't know where to >>>> look.) >>>> Problem also exists in 2.6.20-rc6-mm2. With 2.6.20-rc6-git1 the power >>>> button of this machine works fine. >>>> >>> That's significant - in your case at least the 2.6.20-rc6-mm3 ACPI >>> update >>> isn't the cause. >>> >> >> Is there anything specific I should test, or Big Bisect time? >> >> > This patch should fix the issue... Yes, after add this patch power button works fine. Thanks -- Maciej Rutecki <maciej.rutecki@gmail.com> [-- Attachment #2: S/MIME Cryptographic Signature --] [-- Type: application/x-pkcs7-signature, Size: 3265 bytes --] ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: 2.6.20-rc6-mm3 2007-01-31 12:29 ` 2.6.20-rc6-mm3 Alexey Starikovskiy 2007-01-31 16:02 ` 2.6.20-rc6-mm3 Maciej Rutecki @ 2007-01-31 18:28 ` Tilman Schmidt 1 sibling, 0 replies; 19+ messages in thread From: Tilman Schmidt @ 2007-01-31 18:28 UTC (permalink / raw) To: Alexey Starikovskiy Cc: Andrew Morton, Maciej Rutecki, linux-kernel, linux-acpi [-- Attachment #1: Type: text/plain, Size: 1403 bytes --] Am 31.01.2007 13:29 schrieb Alexey Starikovskiy: [...] >>>>> Second problem, power button doesn't work. [...] > This patch should fix the issue... It does. Power button works again. Thanks, Tilman > ------------------------------------------------------------------------ > > Correct id for fixed buttons. > ACPI_BUTTON_HID_POWERF was changed, but this change was not propogated to button.c, > thus breaking detection of fixed power and sleep buttons. > From: Alexey Starikovskiy <alexey.y.starikovskiy@linux.intel.com> > > > --- > > drivers/acpi/button.c | 2 +- > 1 files changed, 1 insertions(+), 1 deletions(-) > > diff --git a/drivers/acpi/button.c b/drivers/acpi/button.c > index ac86058..c726612 100644 > --- a/drivers/acpi/button.c > +++ b/drivers/acpi/button.c > @@ -75,7 +75,7 @@ static int acpi_button_state_open_fs(str > static struct acpi_driver acpi_button_driver = { > .name = ACPI_BUTTON_DRIVER_NAME, > .class = ACPI_BUTTON_CLASS, > - .ids = "ACPI_FPB,ACPI_FSB,PNP0C0D,PNP0C0C,PNP0C0E", > + .ids = "button_power,button_sleep,PNP0C0D,PNP0C0C,PNP0C0E", > .ops = { > .add = acpi_button_add, > .remove = acpi_button_remove, -- Tilman Schmidt E-Mail: tilman@imap.cc Bonn, Germany Diese Nachricht besteht zu 100% aus wiederverwerteten Bits. Ungeöffnet mindestens haltbar bis: (siehe Rückseite) [-- Attachment #2: OpenPGP digital signature --] [-- Type: application/pgp-signature, Size: 253 bytes --] ^ permalink raw reply [flat|nested] 19+ messages in thread
* [-mm patch] #ifdef ACPI_FUTURE_USAGE acpi_os_readable() [not found] <20070129204528.eb8d695e.akpm@osdl.org> [not found] ` <45BFC442.5000903@gmail.com> @ 2007-02-06 22:11 ` Adrian Bunk 1 sibling, 0 replies; 19+ messages in thread From: Adrian Bunk @ 2007-02-06 22:11 UTC (permalink / raw) To: Andrew Morton, lenb; +Cc: linux-kernel, linux-acpi On Mon, Jan 29, 2007 at 08:45:28PM -0800, Andrew Morton wrote: >... > Changes since 2.6.20-rc6-mm2: >... > git-acpi.patch >... > git trees >... acpi_os_readable() is no longer used. Signed-off-by: Adrian Bunk <bunk@stusta.de> --- drivers/acpi/osl.c | 2 -- include/acpi/acpiosxf.h | 3 +-- 2 files changed, 1 insertion(+), 4 deletions(-) --- linux-2.6.20-rc6-mm3/include/acpi/acpiosxf.h.old 2007-02-06 06:57:15.000000000 +0100 +++ linux-2.6.20-rc6-mm3/include/acpi/acpiosxf.h 2007-02-06 06:57:53.000000000 +0100 @@ -240,9 +240,8 @@ acpi_os_validate_address(u8 space_id, acpi_physical_address address, acpi_size length); -u8 acpi_os_readable(void *pointer, acpi_size length); - #ifdef ACPI_FUTURE_USAGE +u8 acpi_os_readable(void *pointer, acpi_size length); u8 acpi_os_writable(void *pointer, acpi_size length); #endif --- linux-2.6.20-rc6-mm3/drivers/acpi/osl.c.old 2007-02-06 07:18:33.000000000 +0100 +++ linux-2.6.20-rc6-mm3/drivers/acpi/osl.c 2007-02-06 07:18:54.000000000 +0100 @@ -888,7 +888,6 @@ return 0; } -#endif /* ACPI_FUTURE_USAGE */ /* Assumes no unreadable holes inbetween */ u8 acpi_os_readable(void *ptr, acpi_size len) @@ -901,7 +900,6 @@ return 1; } -#ifdef ACPI_FUTURE_USAGE u8 acpi_os_writable(void *ptr, acpi_size len) { /* could do dummy write (racy) or a kernel page table lookup. ^ permalink raw reply [flat|nested] 19+ messages in thread
end of thread, other threads:[~2007-02-06 22:11 UTC | newest]
Thread overview: 19+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <20070129204528.eb8d695e.akpm@osdl.org>
[not found] ` <45BFC442.5000903@gmail.com>
2007-01-30 22:27 ` 2.6.20-rc6-mm3 Andrew Morton
2007-01-31 0:55 ` 2.6.20-rc6-mm3 Karsten Wiese
2007-01-31 13:22 ` 2.6.20-rc6-mm3 Ingo Molnar
2007-01-31 14:25 ` 2.6.20-rc6-mm3 Karsten Wiese
2007-02-01 8:01 ` 2.6.20-rc6-mm3 Ingo Molnar
2007-02-01 10:44 ` 2.6.20-rc6-mm3 Karsten Wiese
2007-02-01 11:12 ` 2.6.20-rc6-mm3 Karsten Wiese
2007-02-01 11:12 ` 2.6.20-rc6-mm3 Karsten Wiese
2007-02-03 0:37 ` 2.6.20-rc6-mm3 Pavel Machek
2007-02-01 13:03 ` [PATCH -mm] gtod persistent clock resume fix Thomas Gleixner
2007-01-31 11:54 ` 2.6.20-rc6-mm3 Maciej Rutecki
2007-02-01 4:10 ` 2.6.20-rc6-mm3 Len Brown
2007-02-01 4:17 ` 2.6.20-rc6-mm3 Andrew Morton
[not found] ` <45BFEDFB.6000500@imap.cc>
2007-01-31 1:25 ` 2.6.20-rc6-mm3 Andrew Morton
2007-01-31 11:38 ` 2.6.20-rc6-mm3 Tilman Schmidt
2007-01-31 12:29 ` 2.6.20-rc6-mm3 Alexey Starikovskiy
2007-01-31 16:02 ` 2.6.20-rc6-mm3 Maciej Rutecki
2007-01-31 18:28 ` 2.6.20-rc6-mm3 Tilman Schmidt
2007-02-06 22:11 ` [-mm patch] #ifdef ACPI_FUTURE_USAGE acpi_os_readable() Adrian Bunk
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).