* dmidecode
@ 2007-12-28 21:01 Ulrich Ivens
2008-01-18 21:18 ` dmidecode (Samsung R40plus) Len Brown
0 siblings, 1 reply; 4+ messages in thread
From: Ulrich Ivens @ 2007-12-28 21:01 UTC (permalink / raw)
To: linux-acpi
As my computer told me to send an output of dmidecode to
linux-acpi@vger.kernel.org I do it.
My Notebook is a Samsung R40plus with Ubuntu 7.10 as operatig system. It works
fine. Suspend and Hibernation doesn't work and the system startup is really
slow. My PIII @ 600 Mhz it boots up in 20 seconts. My notebook takes up to 3
minutes (but not at every boot, sometimes it takes only 20 seconds)
Bu here is the output:
ulli@ubuntunotebook:~$ sudo dmidecode
[sudo] password for ulli:
# dmidecode 2.9
SMBIOS 2.4 present.
29 structures occupying 1023 bytes.
Table at 0x000DC010.
Handle 0x0000, DMI type 0, 24 bytes
BIOS Information
Vendor: Phoenix Technologies LTD
Version: 06YE
Release Date: 07/18/2007
Address: 0xE53C0
Runtime Size: 109632 bytes
ROM Size: 1024 kB
Characteristics:
ISA is supported
PCI is supported
PC Card (PCMCIA) is supported
PNP is supported
APM is supported
BIOS is upgradeable
BIOS shadowing is allowed
ESCD support is available
Boot from CD is supported
ACPI is supported
USB legacy is supported
LS-120 boot is supported
ATAPI Zip drive boot is supported
BIOS boot specification is supported
Targeted content distribution is supported
Handle 0x0001, DMI type 1, 27 bytes
System Information
Manufacturer: SAMSUNG ELECTRONICS CO., LTD.
Product Name: R40P/R41P
Version: 01YE
Serial Number: 987V93CP300020
UUID: 609A7519-D21D-B211-8000-C10FFE3A9BBA
Wake-up Type: Power Switch
SKU Number: Not Specified
Family: Not Specified
Handle 0x0002, DMI type 2, 8 bytes
Base Board Information
Manufacturer: SAMSUNG ELECTRONICS CO., LTD.
Product Name: R40P/R41P
Version:
Serial Number: 123490EN400015
Handle 0x0003, DMI type 3, 17 bytes
Chassis Information
Manufacturer: SAMSUNG ELECTRONICS CO., LTD.
Type: Other
Lock: Not Present
Version: N/A
Serial Number: None
Asset Tag: No Asset Tag
Boot-up State: Safe
Power Supply State: Safe
Thermal State: Safe
Security Status: None
OEM Information: 0x00001234
Handle 0x0004, DMI type 4, 35 bytes
Processor Information
Socket Designation: U2E1
Type: Central Processor
Family: Celeron D
Manufacturer: Intel
ID: EC 06 00 00 FF FB E9 BF
Signature: Type 0, Family 6, Model 14, Stepping 12
Flags:
FPU (Floating-point unit on-chip)
VME (Virtual mode extension)
DE (Debugging extension)
PSE (Page size extension)
TSC (Time stamp counter)
MSR (Model specific registers)
PAE (Physical address extension)
MCE (Machine check exception)
CX8 (CMPXCHG8 instruction supported)
APIC (On-chip APIC hardware supported)
SEP (Fast system call)
MTRR (Memory type range registers)
PGE (Page global enable)
MCA (Machine check architecture)
CMOV (Conditional move instruction supported)
PAT (Page attribute table)
CLFSH (CLFLUSH instruction supported)
DS (Debug store)
ACPI (ACPI supported)
MMX (MMX technology supported)
FXSR (Fast floating-point save and restore)
SSE (Streaming SIMD extensions)
SSE2 (Streaming SIMD extensions 2)
SS (Self-snoop)
HTT (Hyper-threading technology)
TM (Thermal monitor supported)
PBE (Pending break enabled)
Version: A0
Voltage: 3.3 V
External Clock: Unknown
Max Speed: 2048 MHz
Current Speed: 1729 MHz
Status: Populated, Enabled
Upgrade: ZIF Socket
L1 Cache Handle: 0x0005
L2 Cache Handle: 0x0006
L3 Cache Handle: Not Provided
Serial Number: Not Specified
Asset Tag: Not Specified
Part Number: Not Specified
Handle 0x0005, DMI type 7, 19 bytes
Cache Information
Socket Designation: L1 Cache
Configuration: Enabled, Socketed, Level 1
Operational Mode: Write Back
Location: Internal
Installed Size: 64 KB
Maximum Size: 64 KB
Supported SRAM Types:
Burst
Pipeline Burst
Asynchronous
Installed SRAM Type: Asynchronous
Speed: Unknown
Error Correction Type: Unknown
System Type: Unknown
Associativity: Unknown
Handle 0x0006, DMI type 7, 19 bytes
Cache Information
Socket Designation: L2 Cache
Configuration: Enabled, Socketed, Level 2
Operational Mode: Write Back
Location: Internal
Installed Size: 2048 KB
Maximum Size: 4096 KB
Supported SRAM Types:
Burst
Pipeline Burst
Installed SRAM Type: Burst
Speed: Unknown
Error Correction Type: Unknown
System Type: Unknown
Associativity: Unknown
Handle 0x0007, DMI type 9, 13 bytes
System Slot Information
Designation: CARDBUS 0
Type: 32-bit PC Card (PCMCIA)
Current Usage: Unknown
Length: Other
ID: Adapter 0, Socket 0
Characteristics:
5.0 V is provided
3.3 V is provided
PC Card-16 is supported
Cardbus is supported
Handle 0x0008, DMI type 11, 5 bytes
OEM Strings
String 1: AABBAAAAAAAA
String 2: 2007/04
Handle 0x0009, DMI type 12, 5 bytes
System Configuration Options
Option 1: Jumper settings can be described here.
Handle 0x000A, DMI type 16, 15 bytes
Physical Memory Array
Location: System Board Or Motherboard
Use: System Memory
Error Correction Type: None
Maximum Capacity: 1 GB
Error Information Handle: Not Provided
Number Of Devices: 2
Handle 0x000B, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x000A
Error Information Handle: No Error
Total Width: 64 bits
Data Width: 64 bits
Size: 512 MB
Form Factor: DIMM
Set: 1
Locator: J400
Bank Locator: Channel A0
Type: DRAM
Type Detail: Synchronous
Speed: Unknown
Manufacturer: Not Specified
Serial Number: Not Specified
Asset Tag: Not Specified
Part Number: Not Specified
Handle 0x000C, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x000A
Error Information Handle: No Error
Total Width: 64 bits
Data Width: 64 bits
Size: 512 MB
Form Factor: DIMM
Set: 3
Locator: J501
Bank Locator: Channel B0
Type: DRAM
Type Detail: Synchronous
Speed: Unknown
Manufacturer: Not Specified
Serial Number: Not Specified
Asset Tag: Not Specified
Part Number: Not Specified
Handle 0x000D, DMI type 18, 23 bytes
32-bit Memory Error Information
Type: OK
Granularity: Unknown
Operation: Unknown
Vendor Syndrome: Unknown
Memory Array Address: Unknown
Device Address: Unknown
Resolution: Unknown
Handle 0x000E, DMI type 19, 15 bytes
Memory Array Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0003FFFFFFF
Range Size: 1 GB
Physical Array Handle: 0x000A
Partition Width: 0
Handle 0x000F, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0001FFFFFFF
Range Size: 512 MB
Physical Device Handle: 0x000B
Memory Array Mapped Address Handle: 0x000E
Partition Row Position: 2
Interleave Position: 1
Interleaved Data Depth: 6
Handle 0x0010, DMI type 21, 7 bytes
Built-in Pointing Device
Type: Touch Pad
Interface: PS/2
Buttons: 4
Handle 0x0011, DMI type 22, 26 bytes
Portable Battery
Location: Rear
Manufacturer: SAMSUNG ELECTRONICS CO., LTD.
Name: SAMSUNG ELECTRONICS CO., LTD.
Chemistry: Lithium Ion
Design Capacity: 1000 mWh
Design Voltage: 19 mV
SBDS Version: BATT_1234
Maximum Error: Unknown
SBDS Serial Number: 0000
SBDS Manufacture Date: 1980-00-00
OEM-specific Information: 0x00000000
Handle 0x0012, DMI type 23, 13 bytes
System Reset
Status: Enabled
Watchdog Timer: Present
Boot Option: Do Not Reboot
Boot Option On Limit: Do Not Reboot
Reset Count: Unknown
Reset Limit: Unknown
Timer Interval: Unknown
Timeout: Unknown
Handle 0x0013, DMI type 24, 5 bytes
Hardware Security
Power-On Password Status: Disabled
Keyboard Password Status: Unknown
Administrator Password Status: Disabled
Front Panel Reset Status: Unknown
Handle 0x0014, DMI type 25, 9 bytes
System Power Controls
Next Scheduled Power-on: 12-31 23:59:59
Handle 0x0015, DMI type 26, 22 bytes
Voltage Probe
Description: Voltage Probe 1
Location: Processor
Status: OK
Maximum Value: Unknown
Minimum Value: Unknown
Resolution: Unknown
Tolerance: Unknown
Accuracy: Unknown
OEM-specific Information: 0x00000000
Nominal Value: 8.192 V
Handle 0x0016, DMI type 27, 14 bytes
Cooling Device
Temperature Probe Handle: 0x0018
Type: Fan
Status: OK
Cooling Unit Group: 255
OEM-specific Information: 0x00000000
Nominal Speed: Unknown Or Non-rotating
Handle 0x0017, DMI type 27, 12 bytes
Cooling Device
Temperature Probe Handle: 0x0018
Type: Fan
Status: OK
Cooling Unit Group: 255
OEM-specific Information: 0x00000000
Handle 0x0018, DMI type 28, 22 bytes
Temperature Probe
Description: Temperature Probe 1
Location: Processor
Status: OK
Maximum Value: Unknown
Minimum Value Unknown
Resolution: Unknown
Tolerance: Unknown
Accuracy: Unknown
OEM-specific Information: 0x00000000
Nominal Value: Unknown
Handle 0x0019, DMI type 29, 22 bytes
Electrical Current Probe
Description: Electrical Current Probe 1
Location: Processor
Status: OK
Maximum Value: Unknown
Minimum Value: Unknown
Resolution: Unknown
Tolerance: Unknown
Accuracy: Unknown
OEM-specific Information: 0x00000000
Nominal Value: Unknown
Handle 0x001A, DMI type 30, 6 bytes
Out-of-band Remote Access
Manufacturer Name: Intel
Inbound Connection: Enabled
Outbound Connection: Disabled
Handle 0x001B, DMI type 32, 20 bytes
System Boot Information
Status: <OUT OF SPEC>
Handle 0x001C, DMI type 127, 4 bytes
End Of Table
Best regards from Germany
Ulrich Ivens
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: dmidecode (Samsung R40plus)
2007-12-28 21:01 dmidecode Ulrich Ivens
@ 2008-01-18 21:18 ` Len Brown
[not found] ` <200801191843.03458.ulrich.ivens@gmx.de>
0 siblings, 1 reply; 4+ messages in thread
From: Len Brown @ 2008-01-18 21:18 UTC (permalink / raw)
To: Ulrich Ivens; +Cc: linux-acpi
> Handle 0x0001, DMI type 1, 27 bytes
> System Information
> Manufacturer: SAMSUNG ELECTRONICS CO., LTD.
> Product Name: R40P/R41P
> Version: 01YE
> Serial Number: 987V93CP300020
> UUID: 609A7519-D21D-B211-8000-C10FFE3A9BBA
> Wake-up Type: Power Switch
> SKU Number: Not Specified
> Family: Not Specified
With 2.6.22, did you notice any functional difference with "acpi_osi=!Linux"?
(or since the default changed at 2.6.23, with 2.6.23 or later
do you notice any difference with "acpi_osi=Linux"?)
Please send me the output from acpidump.
If you don't have acpidump, you can get it from pmtools here:
http://www.lesswatts.org/projects/acpi/utilities.php
thanks,
-Len
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: dmidecode (Samsung R40plus)
[not found] ` <200801191843.03458.ulrich.ivens@gmx.de>
@ 2008-01-21 5:05 ` Len Brown
[not found] ` <200801212232.45612.ulrich.ivens@gmx.de>
0 siblings, 1 reply; 4+ messages in thread
From: Len Brown @ 2008-01-21 5:05 UTC (permalink / raw)
To: Ulrich Ivens; +Cc: linux-acpi, venkatesh.pallipadi
On Saturday 19 January 2008 12:43, Ulrich Ivens wrote:
> Am Freitag 18 Januar 2008 22:18:50 schrieben Sie:
> > > Handle 0x0001, DMI type 1, 27 bytes
> > > System Information
> > > Manufacturer: SAMSUNG ELECTRONICS CO., LTD.
> > > Product Name: R40P/R41P
> > > Version: 01YE
> > > Serial Number: 987V93CP300020
> > > UUID: 609A7519-D21D-B211-8000-C10FFE3A9BBA
> > > Wake-up Type: Power Switch
> > > SKU Number: Not Specified
> > > Family: Not Specified
> >
> > With 2.6.22, did you notice any functional difference with
> > "acpi_osi=!Linux"?
>
> No, no significant changes happened.
>
>
> > (or since the default changed at 2.6.23, with 2.6.23 or later
> > do you notice any difference with "acpi_osi=Linux"?)
>
> It's still the Kernel 2.6.22 with ubuntu linux.
>
> > Please send me the output from acpidump.
> > If you don't have acpidump, you can get it from pmtools here:
> > http://www.lesswatts.org/projects/acpi/utilities.php
> >
> > thanks,
> > -Len
>
> I tried three things for you:
>
> I set the menu.lst Parameters in kernel line explicit to
> 1. acpi_osi=!Linux,
> 2. acpi_osi=Linux
> 3. nothing
>
> Each time I made an acpidump like you told me. I attached them to the mail. I
> also added one output from dmesg.
thanks for the acpidump.
I wouldn't expect it to change for each case, though curiously,
some bits inside the HPET table did change.
Venki, should I be concerned about the "Hardware Block ID"?
< * Disassembly of HPET.dat, Sun Jan 20 19:41:11 2008
---
> * Disassembly of HPET.dat, Sun Jan 20 19:40:40 2008
15c15
< [009h 009 1] Checksum : 8B
---
> [009h 009 1] Checksum : 9A
22c22
< [024h 036 4] Hardware Block ID : 43538310
---
> [024h 036 4] Hardware Block ID : 43538301
39c39
< 0000: 48 50 45 54 38 00 00 00 01 8B 50 54 4C 54 44 20 HPET8.....PTLTD
---
> 0000: 48 50 45 54 38 00 00 00 01 9A 50 54 4C 54 44 20 HPET8.....PTLTD
41c41
< 0020: 01 00 00 00 10 83 53 43 00 08 00 00 00 00 D0 FE ......SC........
---
> 0020: 01 00 00 00 01 83 53 43 00 08 00 00 00 00 D0 FE ......SC........
> Greetings from Heinsberg, Germany
>
> Ulli
>
>
Re: OSI(Linux)
Method (OSTP, 0, NotSerialized)
# OSTP return value is never checked
{
If (LEqual (^OSTB, Ones))
{
If (CondRefOf (\_OSI, Local0))
{
Store (0x00, ^OSTB)
Store (0x00, ^TPOS)
If (\_OSI ("Windows 2001"))
{
Store (0x08, ^OSTB)
Store (0x08, ^TPOS)
}
If (\_OSI ("Linux"))
{
Store (0x01, LINX)
# LINX is a NOP here, since it is never referenced
Store (0x80, ^OSTB)
# there are quite a few references to OSTB == x40 (Vista)
# which will be disabled by OSI(Linux),
# including code under the RTC, PNP0100 timer, PNP0C32 button
# PNP0103 HPET
Store (0x80, ^TPOS)
# TPOS is only compared against 4 (NT)
}
So I I think it is not a good idea to enable OSI(Linux) on this box.
For it enables nothing, and disables hooks for Vista and newer.
It would be interesting if you notice any difference in the dmesg
with and without acpi_osi=Linux in 2.6.24-rc -- particularly any
messages about the timers.
-Len
^ permalink raw reply [flat|nested] 4+ messages in thread
* BUG: soft lockup - CPU#0 stuck for 186s (Re: dmidecode (Samsung R40plus))
[not found] ` <200801212232.45612.ulrich.ivens@gmx.de>
@ 2008-01-22 4:45 ` Len Brown
0 siblings, 0 replies; 4+ messages in thread
From: Len Brown @ 2008-01-22 4:45 UTC (permalink / raw)
To: Ulrich Ivens; +Cc: linux-acpi
> I downloaded the Vanilla Kernel 2.6.24-rc8, compiled an installed it. It
> works, but it is the same with it. My Ubuntu need up to 6 Minutes to boot.
that is because twice you locked up.
Did this same failure happen back in 2.6.22?
What is the most recent kernel where this did not happen?
I don't understand this message:
> [ 344.253937] toshiba_acpi: Unknown parameter `hotkeys_over_acpi'
Since 2.6.24-rc8 does not contain that symbol.
maybe you should boot a static 2.6.24-rc8 kernel with no drivers
and no initrd and see how that works?
thanks,
-Len
> [ 0.000000] Linux version 2.6.24-rc8 (root@ubuntunotebook) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Mon Jan 21 20:07:10 CET 2008
> [ 0.000000] BIOS-provided physical RAM map:
> [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
> [ 0.000000] BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
> [ 0.000000] BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved)
> [ 0.000000] BIOS-e820: 00000000000dc000 - 00000000000e0000 (reserved)
> [ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
> [ 0.000000] BIOS-e820: 0000000000100000 - 0000000037e90000 (usable)
> [ 0.000000] BIOS-e820: 0000000037e90000 - 0000000037e9e000 (ACPI data)
> [ 0.000000] BIOS-e820: 0000000037e9e000 - 0000000037e9f000 (ACPI NVS)
> [ 0.000000] BIOS-e820: 0000000037e9f000 - 0000000038000000 (reserved)
> [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
> [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
> [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> [ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
> [ 0.000000] 0MB HIGHMEM available.
> [ 0.000000] 894MB LOWMEM available.
> [ 0.000000] found SMP MP-table at 000f7ea0
> [ 0.000000] Entering add_active_range(0, 0, 229008) 0 entries of 256 used
> [ 0.000000] Zone PFN ranges:
> [ 0.000000] DMA 0 -> 4096
> [ 0.000000] Normal 4096 -> 229008
> [ 0.000000] HighMem 229008 -> 229008
> [ 0.000000] Movable zone start PFN for each node
> [ 0.000000] early_node_map[1] active PFN ranges
> [ 0.000000] 0: 0 -> 229008
> [ 0.000000] On node 0 totalpages: 229008
> [ 0.000000] DMA zone: 32 pages used for memmap
> [ 0.000000] DMA zone: 0 pages reserved
> [ 0.000000] DMA zone: 4064 pages, LIFO batch:0
> [ 0.000000] Normal zone: 1757 pages used for memmap
> [ 0.000000] Normal zone: 223155 pages, LIFO batch:31
> [ 0.000000] HighMem zone: 0 pages used for memmap
> [ 0.000000] Movable zone: 0 pages used for memmap
> [ 0.000000] DMI present.
> [ 0.000000] ACPI: RSDP 000F7E70, 0014 (r0 PTLTD )
> [ 0.000000] ACPI: RSDT 37E97718, 0044 (r1 SECCSD LH43STAR 6040000 LTP 0)
> [ 0.000000] ACPI: FACP 37E9DD4E, 0074 (r1 SEC FIRENZE2 6040000 SEC F4240)
> [ 0.000000] ACPI: DSDT 37E98AE0, 526E (r1 ATI SB600 6040000 INTL 20050228)
> [ 0.000000] ACPI: FACS 37E9EFC0, 0040
> [ 0.000000] ACPI: APIC 37E9DDC2, 0054 (r1 PTLTD APIC 6040000 LTP 0)
> [ 0.000000] ACPI: MCFG 37E9DE16, 003C (r1 PTLTD MCFG 6040000 LTP 0)
> [ 0.000000] ACPI: HPET 37E9DE52, 0038 (r1 PTLTD HPETTBL 6040000 LTP 1)
> [ 0.000000] ACPI: SLIC 37E9DE8A, 0176 (r1 SECCSD LH43STAR 6040000 LTP 0)
> [ 0.000000] ACPI: SSDT 37E97D75, 025F (r1 PmRef Cpu0Tst 3000 INTL 20050228)
> [ 0.000000] ACPI: SSDT 37E97CCF, 00A6 (r1 PmRef Cpu1Tst 3000 INTL 20050228)
> [ 0.000000] ACPI: SSDT 37E9775C, 0573 (r1 PmRef CpuPm 3000 INTL 20050228)
> [ 0.000000] ATI board detected. Disabling timer routing over 8254.
> [ 0.000000] ACPI: PM-Timer IO Port: 0x8008
> [ 0.000000] ACPI: Local APIC address 0xfee00000
> [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
> [ 0.000000] Processor #0 6:14 APIC version 20
> [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
> [ 0.000000] Processor #1 6:14 APIC version 20
> [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
> [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
> [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
> [ 0.000000] IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
> [ 0.000000] ACPI: IRQ9 used by override.
> [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
> [ 0.000000] ACPI: HPET id: 0x43538301 base: 0xfed00000
> [ 0.000000] Using ACPI (MADT) for SMP configuration information
> [ 0.000000] Allocating PCI resources starting at 40000000 (gap: 38000000:a8000000)
> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 227219
> [ 0.000000] Kernel command line: root=UUID=62696e7b-6b0b-40fa-96fc-1dbb91d72f6c ro
> [ 0.000000] mapped APIC to ffffb000 (fee00000)
> [ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
> [ 0.000000] Enabling fast FPU save and restore... done.
> [ 0.000000] Enabling unmasked SIMD FPU exception support... done.
> [ 0.000000] Initializing CPU#0
> [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
> [ 0.000000] Detected 1729.210 MHz processor.
> [ 15.930021] Console: colour VGA+ 80x25
> [ 15.930024] console [tty0] enabled
> [ 15.933057] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
> [ 15.933570] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
> [ 15.956565] Memory: 862332k/916032k available (2026k kernel code, 53072k reserved, 940k data, 336k init, 0k highmem)
> [ 15.956624] virtual kernel memory layout:
> [ 15.956625] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
> [ 15.956626] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
> [ 15.956628] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
> [ 15.956629] lowmem : 0xc0000000 - 0xf7e90000 ( 894 MB)
> [ 15.956630] .init : 0xc03eb000 - 0xc043f000 ( 336 kB)
> [ 15.956631] .data : 0xc02fabb3 - 0xc03e5d24 ( 940 kB)
> [ 15.956632] .text : 0xc0100000 - 0xc02fabb3 (2026 kB)
> [ 15.956971] Checking if this processor honours the WP bit even in supervisor mode... Ok.
> [ 15.957091] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
> [ 15.957287] hpet clockevent registered
> [ 16.037262] Calibrating delay using timer specific routine.. 3461.40 BogoMIPS (lpj=6922809)
> [ 16.037367] Security Framework initialized
> [ 16.037415] SELinux: Disabled at boot.
> [ 16.037469] Mount-cache hash table entries: 512
> [ 16.037632] CPU: After generic identify, caps: bfe9fbff 00000000 00000000 00000000 0000c189 00000000 00000000 00000000
> [ 16.037641] monitor/mwait feature present.
> [ 16.037685] using mwait in idle threads.
> [ 16.037730] CPU: L1 I cache: 32K, L1 D cache: 32K
> [ 16.037807] CPU: L2 cache: 2048K
> [ 16.037851] CPU: Physical Processor ID: 0
> [ 16.037894] CPU: Processor Core ID: 0
> [ 16.037936] CPU: After all inits, caps: bfe9fbff 00000000 00000000 00002940 0000c189 00000000 00000000 00000000
> [ 16.037945] Compat vDSO mapped to ffffe000.
> [ 16.037999] Checking 'hlt' instruction... OK.
> [ 16.053704] SMP alternatives: switching to UP code
> [ 16.054510] ACPI: Core revision 20070126
> [ 17.096953] CPU0: Intel(R) Core(TM) Duo CPU T2250 @ 1.73GHz stepping 0c
> [ 17.097080] SMP alternatives: switching to SMP code
> [ 17.097541] Booting processor 1/1 eip 3000
> [ 17.107794] Initializing CPU#1
> [ 17.184833] Calibrating delay using timer specific routine.. 3458.31 BogoMIPS (lpj=6916634)
> [ 17.184841] CPU: After generic identify, caps: bfe9fbff 00000000 00000000 00000000 0000c189 00000000 00000000 00000000
> [ 17.184847] monitor/mwait feature present.
> [ 17.184851] CPU: L1 I cache: 32K, L1 D cache: 32K
> [ 17.184853] CPU: L2 cache: 2048K
> [ 17.184855] CPU: Physical Processor ID: 0
> [ 17.184856] CPU: Processor Core ID: 1
> [ 17.184858] CPU: After all inits, caps: bfe9fbff 00000000 00000000 00002940 0000c189 00000000 00000000 00000000
> [ 17.185341] CPU1: Intel(R) Core(TM) Duo CPU T2250 @ 1.73GHz stepping 0c
> [ 17.185762] Total of 2 processors activated (6919.72 BogoMIPS).
> [ 17.185961] ENABLING IO-APIC IRQs
> [ 17.186184] ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
> [ 17.225941] ..MP-BIOS bug: 8254 timer not connected to IO-APIC
> [ 17.225985] ...trying to set up timer (IRQ0) through the 8259A ... failed.
> [ 17.226063] ...trying to set up timer as Virtual Wire IRQ... failed.
> [ 17.265860] ...trying to set up timer as ExtINT IRQ... works.
> [ 17.512840] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
> [ 17.532930] Brought up 2 CPUs
> [ 17.532990] CPU0 attaching sched-domain:
> [ 17.532993] domain 0: span 03
> [ 17.532995] groups: 01 02
> [ 17.532999] CPU1 attaching sched-domain:
> [ 17.533000] domain 0: span 03
> [ 17.533002] groups: 02 01
> [ 17.533301] net_namespace: 64 bytes
> [ 17.533835] Time: 21:38:59 Date: 01/21/08
> [ 17.533907] NET: Registered protocol family 16
> [ 17.534170] EISA bus registered
> [ 17.534215] ACPI: bus type pci registered
> [ 17.534348] PCI: Using MMCONFIG
> [ 17.535212] Setting up standard PCI resources
> [ 17.540361] ACPI: EC: Look up EC in DSDT
> [ 17.543493] ACPI: System BIOS is requesting _OSI(Linux)
> [ 17.543537] ACPI: If "acpi_osi=Linux" works better,
> [ 17.543538] Please send dmidecode to linux-acpi@vger.kernel.org
> [ 19.544569] ACPI: Interpreter enabled
> [ 19.544613] ACPI: (supports S0 S3 S5)
> [ 19.544763] ACPI: Using IOAPIC for interrupt routing
> [ 19.545137] ACPI: EC: non-query interrupt received, switching to interrupt mode
> [ 19.550808] ACPI: EC: GPE = 0x3, I/O: command/status = 0x66, data = 0x62
> [ 19.550853] ACPI: EC: driver started in interrupt mode
> [ 19.550947] ACPI: PCI Root Bridge [PCI0] (0000:00)
> [ 19.552478] PCI: Transparent bridge - 0000:00:14.4
> [ 19.552608] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> [ 19.552825] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
> [ 19.552973] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
> [ 19.555698] ACPI: PCI Interrupt Link [LNKA] (IRQs 11) *0, disabled.
> [ 19.556026] ACPI: PCI Interrupt Link [LNKB] (IRQs 10) *0, disabled.
> [ 19.556356] ACPI: PCI Interrupt Link [LNKC] (IRQs 5) *0, disabled.
> [ 19.556681] ACPI: PCI Interrupt Link [LNKD] (IRQs 5) *0, disabled.
> [ 19.557006] ACPI: PCI Interrupt Link [LNKE] (IRQs 11) *0, disabled.
> [ 19.557331] ACPI: PCI Interrupt Link [LNKF] (IRQs 10) *0, disabled.
> [ 19.557656] ACPI: PCI Interrupt Link [LNKG] (IRQs 11) *0, disabled.
> [ 19.557980] ACPI: PCI Interrupt Link [LNKH] (IRQs 5) *0, disabled.
> [ 19.558323] ACPI: Power Resource [FN00] (off)
> [ 19.558425] Linux Plug and Play Support v0.97 (c) Adam Belay
> [ 19.558508] pnp: PnP ACPI init
> [ 19.558555] ACPI: bus type pnp registered
> [ 19.561311] pnp: PnP ACPI: found 11 devices
> [ 19.561354] ACPI: ACPI bus type pnp unregistered
> [ 19.561399] PnPBIOS: Disabled by ACPI PNP
> [ 19.561691] PCI: Using ACPI for IRQ routing
> [ 19.561734] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
> [ 19.587931] NET: Registered protocol family 8
> [ 19.587975] NET: Registered protocol family 20
> [ 19.588056] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
> [ 19.588271] hpet0: 4 32-bit timers, 14318180 Hz
> [ 19.591909] Time: tsc clocksource has been installed.
> [ 19.591961] Switched to high resolution mode on CPU 0
> [ 19.592120] Switched to high resolution mode on CPU 1
> [ 19.607819] system 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
> [ 19.607877] system 00:08: ioport range 0x1080-0x1080 has been reserved
> [ 19.607922] system 00:08: ioport range 0x220-0x22f has been reserved
> [ 19.607966] system 00:08: ioport range 0x40b-0x40b has been reserved
> [ 19.608011] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
> [ 19.608055] system 00:08: ioport range 0x4d6-0x4d6 has been reserved
> [ 19.608100] system 00:08: ioport range 0x530-0x537 has been reserved
> [ 19.608144] system 00:08: ioport range 0xc00-0xc01 has been reserved
> [ 19.608189] system 00:08: ioport range 0xc14-0xc14 has been reserved
> [ 19.608233] system 00:08: ioport range 0xc50-0xc52 has been reserved
> [ 19.608278] system 00:08: ioport range 0xc6c-0xc6c has been reserved
> [ 19.608322] system 00:08: ioport range 0xc6f-0xc6f has been reserved
> [ 19.608367] system 00:08: ioport range 0xcd0-0xcd1 has been reserved
> [ 19.608411] system 00:08: ioport range 0xcd2-0xcd3 has been reserved
> [ 19.608456] system 00:08: ioport range 0xcd4-0xcd5 has been reserved
> [ 19.608500] system 00:08: ioport range 0xcd6-0xcd7 has been reserved
> [ 19.608545] system 00:08: ioport range 0xcd8-0xcdf has been reserved
> [ 19.608590] system 00:08: ioport range 0x8000-0x805f has been reserved
> [ 19.608634] system 00:08: ioport range 0x8210-0x821f has been reserved
> [ 19.608679] system 00:08: ioport range 0xf40-0xf47 has been reserved
> [ 19.608724] system 00:08: ioport range 0x280-0x293 has been reserved
> [ 19.608768] system 00:08: ioport range 0x87f-0x87f has been reserved
> [ 19.608826] system 00:09: iomem range 0xe0000-0xfffff could not be reserved
> [ 19.608872] system 00:09: iomem range 0xfff00000-0xffffffff could not be reserved
> [ 19.608921] system 00:09: iomem range 0x0-0xfff could not be reserved
> [ 19.639430] PCI: Bridge: 0000:00:01.0
> [ 19.639473] IO window: 9000-9fff
> [ 19.639516] MEM window: d0100000-d01fffff
> [ 19.639559] PREFETCH window: d8000000-dfffffff
> [ 19.639607] PCI: Bus 3, cardbus bridge: 0000:02:09.0
> [ 19.640472] IO window: 0000a400-0000a4ff
> [ 19.640517] IO window: 0000a800-0000a8ff
> [ 19.640562] PREFETCH window: 40000000-43ffffff
> [ 19.640608] MEM window: 44000000-47ffffff
> [ 19.640653] PCI: Bridge: 0000:00:14.4
> [ 19.640696] IO window: a000-afff
> [ 19.640741] MEM window: f0200000-f02fffff
> [ 19.640788] PREFETCH window: f0300000-f03fffff
> [ 19.640904] ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 20 (level, low) -> IRQ 16
> [ 19.640999] NET: Registered protocol family 2
> [ 19.680814] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
> [ 19.681115] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
> [ 19.681893] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
> [ 19.682337] TCP: Hash tables configured (established 131072 bind 65536)
> [ 19.682382] TCP reno registered
> [ 19.692921] checking if image is initramfs... it is
> [ 23.495235] Freeing initrd memory: 41191k freed
> [ 23.496249] audit: initializing netlink socket (disabled)
> [ 23.496308] audit(1200951544.209:1): initialized
> [ 23.498732] VFS: Disk quotas dquot_6.5.1
> [ 23.498855] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> [ 23.499029] io scheduler noop registered
> [ 23.499071] io scheduler anticipatory registered
> [ 23.499114] io scheduler deadline registered
> [ 23.499166] io scheduler cfq registered (default)
> [ 23.499287] Boot video device is 0000:01:05.0
> [ 23.499532] isapnp: Scanning for PnP cards...
> [ 23.853806] isapnp: No Plug & Play device found
> [ 23.878642] Real Time Clock Driver v1.12ac
> [ 23.878967] hpet_resources: 0xfed00000 is busy
> [ 23.878997] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
> [ 23.880405] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
> [ 23.880526] input: Macintosh mouse button emulation as /class/input/input0
> [ 23.880673] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
> [ 23.883400] i8042.c: Detected active multiplexing controller, rev 1.1.
> [ 23.884803] serio: i8042 KBD port at 0x60,0x64 irq 1
> [ 23.884850] serio: i8042 AUX0 port at 0x60,0x64 irq 12
> [ 23.884897] serio: i8042 AUX1 port at 0x60,0x64 irq 12
> [ 23.884943] serio: i8042 AUX2 port at 0x60,0x64 irq 12
> [ 23.884987] serio: i8042 AUX3 port at 0x60,0x64 irq 12
> [ 23.899487] mice: PS/2 mouse device common for all mice
> [ 23.899661] EISA: Probing bus 0 at eisa.0
> [ 23.899711] Cannot allocate resource for EISA slot 1
> [ 23.899781] Cannot allocate resource for EISA slot 8
> [ 23.899824] EISA: Detected 0 cards.
> [ 23.899951] TCP cubic registered
> [ 23.900000] NET: Registered protocol family 1
> [ 23.900070] Using IPI No-Shortcut mode
> [ 23.900254] Magic number: 8:356:652
> [ 23.900664] Freeing unused kernel memory: 336k freed
> [ 23.922524] input: AT Translated Set 2 keyboard as /class/input/input1
> [ 24.082855] fuse init (API version 7.9)
> [ 24.087549] ACPI: Fan [FAN0] (off)
> [ 24.093278] ACPI: SSDT 37E98750, 02E6 (r1 PmRef Cpu0Ist 3000 INTL 20050228)
> [ 24.093926] ACPI: SSDT 37E97FD4, 06F7 (r1 PmRef Cpu0Cst 3001 INTL 20050228)
> [ 24.096045] ACPI: CPU0 (power states: C1[C1] C2[C2])
> [ 24.096193] ACPI: Processor [CPU0] (supports 8 throttling states)
> [ 24.096545] ACPI: SSDT 37E98A36, 00AA (r1 PmRef Cpu1Ist 3000 INTL 20050228)
> [ 24.096843] ACPI: SSDT 37E986CB, 0085 (r1 PmRef Cpu1Cst 3000 INTL 20050228)
> [ 24.097599] ACPI: CPU1 (power states: C1[C1] C2[C2])
> [ 24.097746] ACPI: Processor [CPU1] (supports 8 throttling states)
> [ 24.099633] ACPI: Thermal Zone [TZ00] (53 C)
> [ 24.100131] ACPI: Thermal Zone [TZ01] (53 C)
> [ 24.464056] SCSI subsystem initialized
> [ 24.482064] libata version 3.00 loaded.
> [ 24.485390] ahci 0000:00:12.0: version 3.0
> [ 24.485425] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 17
> [ 24.485537] ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit
> [ 24.485585] ahci 0000:00:12.0: controller can't do PMP, turning off CAP_PMP
> [ 24.526923] usbcore: registered new interface driver usbfs
> [ 24.527002] usbcore: registered new interface driver hub
> [ 24.527070] usbcore: registered new device driver usb
> [ 24.551925] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
> [ 24.781965] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> [ 24.782779] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> [ 24.793717] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
> [ 25.485782] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
> [ 25.485864] ahci 0000:00:12.0: flags: ncq sntf ilck pm led clo pio slum part
> [ 25.486341] scsi0 : ahci
> [ 25.486602] scsi1 : ahci
> [ 25.486793] scsi2 : ahci
> [ 25.486973] scsi3 : ahci
> [ 25.487107] ata1: SATA max UDMA/133 abar m1024@0xd0004000 port 0xd0004100 irq 17
> [ 25.487159] ata2: SATA max UDMA/133 abar m1024@0xd0004000 port 0xd0004180 irq 17
> [ 25.487210] ata3: SATA max UDMA/133 abar m1024@0xd0004000 port 0xd0004200 irq 17
> [ 25.487260] ata4: SATA max UDMA/133 abar m1024@0xd0004000 port 0xd0004280 irq 17
> [ 25.961578] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> [ 25.970536] ata1.00: ATA-7: SAMSUNG HM120JI, YF100-13, max UDMA7
> [ 25.970599] ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32)
> [ 25.976640] ata1.00: configured for UDMA/133
> [ 26.285460] ata2: SATA link down (SStatus 0 SControl 300)
> [ 26.597344] ata3: SATA link down (SStatus 0 SControl 300)
> [ 26.910231] ata4: SATA link down (SStatus 0 SControl 300)
> [ 26.910553] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HM120JI YF10 PQ: 0 ANSI: 5
> [ 26.911016] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 18
> [ 26.911113] ohci_hcd 0000:00:13.0: OHCI Host Controller
> [ 26.911414] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
> [ 26.911484] ohci_hcd 0000:00:13.0: irq 18, io mem 0xd0005000
> [ 26.918249] Driver 'sd' needs updating - please use bus_type methods
> [ 26.926317] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
> [ 26.926401] sd 0:0:0:0: [sda] Write Protect is off
> [ 26.926459] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 26.926496] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [ 26.926635] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
> [ 26.926689] sd 0:0:0:0: [sda] Write Protect is off
> [ 26.926732] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 26.926748] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [ 26.926800] sda:<6>usb usb1: configuration #1 chosen from 1 choice
> [ 26.965559] hub 1-0:1.0: USB hub found
> [ 26.965623] hub 1-0:1.0: 2 ports detected
> [ 27.069355] ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 17 (level, low) -> IRQ 19
> [ 27.069483] ohci_hcd 0000:00:13.1: OHCI Host Controller
> [ 27.069578] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
> [ 27.069645] ohci_hcd 0000:00:13.1: irq 19, io mem 0xd0006000
> [ 27.126353] usb usb2: configuration #1 chosen from 1 choice
> [ 27.126461] hub 2-0:1.0: USB hub found
> [ 27.126531] hub 2-0:1.0: 2 ports detected
> [ 27.230255] ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 20
> [ 27.230376] ohci_hcd 0000:00:13.2: OHCI Host Controller
> [ 27.230483] ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
> [ 27.230546] ohci_hcd 0000:00:13.2: irq 20, io mem 0xd0007000
> [ 27.285292] usb usb3: configuration #1 chosen from 1 choice
> [ 27.285397] hub 3-0:1.0: USB hub found
> [ 27.285468] hub 3-0:1.0: 2 ports detected
> [ 27.369067] sda1 sda2 <<6>usb 1-1: new low speed USB device using ohci_hcd and address 2
> [ 27.389208] ACPI: PCI Interrupt 0000:00:13.3[B] -> GSI 17 (level, low) -> IRQ 19
> [ 27.389329] ohci_hcd 0000:00:13.3: OHCI Host Controller
> [ 27.389432] ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 4
> [ 27.389492] ohci_hcd 0000:00:13.3: irq 19, io mem 0xd0008000
> [ 27.396915] sda5 >
> [ 27.397255] sd 0:0:0:0: [sda] Attached SCSI disk
> [ 27.411538] sd 0:0:0:0: Attached scsi generic sg0 type 0
> [ 27.446333] usb usb4: configuration #1 chosen from 1 choice
> [ 27.446434] hub 4-0:1.0: USB hub found
> [ 27.446484] hub 4-0:1.0: 2 ports detected
> [ 27.550240] ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level, low) -> IRQ 20
> [ 27.550383] ohci_hcd 0000:00:13.4: OHCI Host Controller
> [ 27.550453] ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 5
> [ 27.550517] ohci_hcd 0000:00:13.4: irq 20, io mem 0xd0009000
> [ 27.598191] usb 1-1: configuration #1 chosen from 1 choice
> [ 27.606217] usb usb5: configuration #1 chosen from 1 choice
> [ 27.606326] hub 5-0:1.0: USB hub found
> [ 27.606388] hub 5-0:1.0: 2 ports detected
> [ 27.709361] ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level, low) -> IRQ 21
> [ 27.710327] ehci_hcd 0000:00:13.5: EHCI Host Controller
> [ 27.710413] ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 6
> [ 27.710504] ehci_hcd 0000:00:13.5: debug port 1
> [ 27.710560] ehci_hcd 0000:00:13.5: irq 21, io mem 0xd0004400
> [ 27.711474] kjournald starting. Commit interval 5 seconds
> [ 27.711488] EXT3-fs: mounted filesystem with ordered data mode.
> [ 27.721920] ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> [ 27.722102] usb usb6: configuration #1 chosen from 1 choice
> [ 27.722172] hub 6-0:1.0: USB hub found
> [ 27.722221] hub 6-0:1.0: 10 ports detected
> [ 27.826113] SB600_PATA: IDE controller (0x1002:0x438c rev 0x00) at PCI slot 0000:00:14.1
> [ 27.826205] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 18
> [ 27.826320] SB600_PATA: not 100% native mode: will probe irqs later
> [ 27.826371] ide0: BM-DMA at 0x8420-0x8427, BIOS settings: hda:DMA, hdb:pio
> [ 27.826496] Probing IDE interface ide0...
> [ 27.857909] usb 1-1: USB disconnect, address 2
> [ 28.353786] usbcore: registered new interface driver hiddev
> [ 28.664600] usb 1-1: new low speed USB device using ohci_hcd and address 3
> [ 28.881741] usb 1-1: configuration #1 chosen from 1 choice
> [ 29.196416] usb 1-2: new low speed USB device using ohci_hcd and address 4
> [ 29.232778] hda: TSSTcorpCD/DVDW TS-L632D, ATAPI CD/DVD-ROM drive
> [ 29.232956] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
> [ 29.233342] hda: UDMA/33 mode selected
> [ 29.233890] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> [ 29.234968] 8139cp 0000:02:05.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
> [ 29.235024] 8139cp 0000:02:05.0: Try the "8139too" driver instead.
> [ 29.430550] usb 1-2: configuration #1 chosen from 1 choice
> [ 29.439825] input: Logitech USB Receiver as /class/input/input2
> [ 29.460354] input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:13.0-1
> [ 29.471553] input: Logitech USB Receiver as /class/input/input3
> [ 29.484377] input,hiddev96: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:13.0-1
> [ 29.494799] input: QTRONIX USB Keyboard and Mouse as /class/input/input4
> [ 29.504300] input: USB HID v1.00 Keyboard [QTRONIX USB Keyboard and Mouse] on usb-0000:00:13.0-2
> [ 29.520435] input: QTRONIX USB Keyboard and Mouse as /class/input/input5
> [ 29.544324] input: USB HID v1.00 Mouse [QTRONIX USB Keyboard and Mouse] on usb-0000:00:13.0-2
> [ 29.544496] usbcore: registered new interface driver usbhid
> [ 29.544557] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
> [ 40.496373] Linux agpgart interface v0.102
> [ 40.543588] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
> [ 40.648784] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
> [ 40.686141] input: Power Button (FF) as /class/input/input6
> [ 40.740331] ACPI: Power Button (FF) [PWRF]
> [ 40.740589] input: Power Button (CM) as /class/input/input7
> [ 40.788305] ACPI: Power Button (CM) [PWRB]
> [ 40.788415] input: Lid Switch as /class/input/input8
> [ 40.804352] ACPI: Lid Switch [LID0]
> [ 40.804475] input: Sleep Button (CM) as /class/input/input9
> [ 40.868265] ACPI: Sleep Button (CM) [SLPB]
> [ 40.872695] ACPI: Battery Slot [BAT1] (battery present)
> [ 40.875775] ACPI: AC Adapter [ADP1] (on-line)
> [ 41.640961] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
> [ 41.705712] input: PC Speaker as /class/input/input10
> [ 41.942859] 8139too Fast Ethernet driver 0.9.28
> [ 41.943228] ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 23 (level, low) -> IRQ 22
> [ 41.944413] eth0: RealTek RTL8139 at 0xf899a000, 00:13:77:36:d1:f6, IRQ 22
> [ 41.944465] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
> [ 41.970403] sdhci: Secure Digital Host Controller Interface driver
> [ 41.970460] sdhci: Copyright(c) Pierre Ossman
> [ 41.970556] sdhci: SDHCI controller found at 0000:02:09.1 [1180:0822] (rev 18)
> [ 41.970640] ACPI: PCI Interrupt 0000:02:09.1[C] -> GSI 22 (level, low) -> IRQ 17
> [ 41.970756] sdhci:slot0: Will use DMA mode even though HW doesn't fully claim to support it.
> [ 41.970861] mmc0: SDHCI at 0xd0210400 irq 17 DMA
> [ 42.054886] Yenta: CardBus bridge found at 0000:02:09.0 [144d:c036]
> [ 42.108863] hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
> [ 42.109131] Uniform CD-ROM driver Revision: 3.20
> [ 42.181572] Yenta: ISA IRQ mask 0x04b8, PCI irq 16
> [ 42.181623] Socket status: 30000006
> [ 42.181667] pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
> [ 42.181712] cs: IO port probe 0xa000-0xafff: clean.
> [ 42.182084] pcmcia: parent PCI bridge Memory window: 0xf0200000 - 0xf02fffff
> [ 42.182129] pcmcia: parent PCI bridge Memory window: 0xf0300000 - 0xf03fffff
> [ 42.820800] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04713/0x200000
> [ 42.862950] input: SynPS/2 Synaptics TouchPad as /class/input/input11
> [ 133.087675] cs: IO port probe 0x100-0x3af: clean.
> [ 133.089795] cs: IO port probe 0x3e0-0x4ff: clean.
> [ 133.090742] cs: IO port probe 0x820-0x8ff: clean.
> [ 133.091522] cs: IO port probe 0xc00-0xcf7: clean.
> [ 133.092315] cs: IO port probe 0xa00-0xaff: clean.
> [ 140.845947] loop: module loaded
> [ 140.935354] lp: driver loaded but no devices found
> [ 141.100031] Adding 2642652k swap on /dev/sda5. Priority:-1 extents:1 across:2642652k
> [ 141.478768] EXT3 FS on sda1, internal journal
> [ 342.056295] BUG: soft lockup - CPU#0 stuck for 186s! [swapper:0]
> [ 342.056360]
> [ 342.056366] Pid: 0, comm: swapper Not tainted (2.6.24-rc8 #1)
> [ 342.056372] EIP: 0060:[<f88323b3>] EFLAGS: 00000202 CPU: 0
> [ 342.056399] EIP is at acpi_processor_idle+0x2ae/0x45b [processor]
> [ 342.056405] EAX: 00000000 EBX: 2aa50ee0 ECX: a424857e EDX: 0000002e
> [ 342.056410] ESI: f78acacc EDI: c043e180 EBP: f78ac800 ESP: c03e7f9c
> [ 342.056415] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
> [ 342.056420] CR0: 8005003b CR2: b7f25570 CR3: 30e65000 CR4: 00000690
> [ 342.056426] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
> [ 342.056431] DR6: ffff0ff0 DR7: 00000400
> [ 342.056437] [<f8832105>] acpi_processor_idle+0x0/0x45b [processor]
> [ 342.056454] [<f8832105>] acpi_processor_idle+0x0/0x45b [processor]
> [ 342.056469] [<c0102633>] cpu_idle+0x53/0xd0
> [ 342.056481] [<c03eba2a>] start_kernel+0x2da/0x360
> [ 342.056492] [<c03eb130>] unknown_bootoption+0x0/0x1f0
> [ 342.056505] =======================
> [ 344.106222] No dock devices found.
> [ 344.253937] toshiba_acpi: Unknown parameter `hotkeys_over_acpi'
> [ 345.927756] ppdev: user-space parallel port driver
> [ 348.189393] RPC: Registered udp transport module.
> [ 348.189398] RPC: Registered tcp transport module.
> [ 348.663046] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
> [ 348.858706] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
> [ 348.892293] NFSD: starting 90-second grace period
> [ 646.533279] BUG: soft lockup - CPU#0 stuck for 276s! [swapper:0]
> [ 646.533357]
> [ 646.533363] Pid: 0, comm: swapper Not tainted (2.6.24-rc8 #1)
> [ 646.533368] EIP: 0060:[<f88323b3>] EFLAGS: 00000206 CPU: 0
> [ 646.533400] EIP is at acpi_processor_idle+0x2ae/0x45b [processor]
> [ 646.533406] EAX: 00000000 EBX: 3f233472 ECX: 8861cc37 EDX: 00000044
> [ 646.533411] ESI: f78acacc EDI: c043e180 EBP: f78ac800 ESP: c03e7f9c
> [ 646.533417] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
> [ 646.533422] CR0: 8005003b CR2: f8c1c684 CR3: 1fab5000 CR4: 00000690
> [ 646.533427] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
> [ 646.533433] DR6: ffff0ff0 DR7: 00000400
> [ 646.533441] [<f8832105>] acpi_processor_idle+0x0/0x45b [processor]
> [ 646.533459] [<f8832105>] acpi_processor_idle+0x0/0x45b [processor]
> [ 646.533475] [<c0102633>] cpu_idle+0x53/0xd0
> [ 646.533489] [<c03eba2a>] start_kernel+0x2da/0x360
> [ 646.533500] [<c03eb130>] unknown_bootoption+0x0/0x1f0
> [ 646.533515] =======================
> [ 668.208102] Bluetooth: Core ver 2.11
> [ 668.208555] NET: Registered protocol family 31
> [ 668.208562] Bluetooth: HCI device and connection manager initialized
> [ 668.208570] Bluetooth: HCI socket layer initialized
> [ 668.262602] Bluetooth: L2CAP ver 2.9
> [ 668.262610] Bluetooth: L2CAP socket layer initialized
> [ 668.364867] Bluetooth: RFCOMM socket layer initialized
> [ 668.365131] Bluetooth: RFCOMM TTY layer initialized
> [ 668.365137] Bluetooth: RFCOMM ver 1.8
> [ 669.473983] NET: Registered protocol family 10
> [ 669.474492] lo: Disabled Privacy Extensions
> [ 1794.229358] eth0: link down
> [ 1794.231775] ADDRCONF(NETDEV_UP): eth0: link is not ready
-
To unsubscribe from this list: send the line "unsubscribe linux-acpi" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2008-01-22 4:45 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2007-12-28 21:01 dmidecode Ulrich Ivens
2008-01-18 21:18 ` dmidecode (Samsung R40plus) Len Brown
[not found] ` <200801191843.03458.ulrich.ivens@gmx.de>
2008-01-21 5:05 ` Len Brown
[not found] ` <200801212232.45612.ulrich.ivens@gmx.de>
2008-01-22 4:45 ` BUG: soft lockup - CPU#0 stuck for 186s (Re: dmidecode (Samsung R40plus)) Len Brown
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).