Hi, little problem here. 2.4.20-pre7 with latest acpi patch boots but i think the bios is a little bit buggy (no BAT status and no suspend) ,so i tried to override the dsdt but it doesn't worked. (I deleted the * before PNP... in dsdt.asl and recompile but still get some errors with iasl) can anyone fix my dsdt? (it's attached) PLEASE I also tried to override the dsdt with the original dsdt(without modification)but both times the same errors (see below) #dmesg Linux version 2.4.20-pre7-acpi (gcc version 3.1.1) #1 Don Sep 19 17:47:12 CEST 2002 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001ffd0000 (usable) BIOS-e820: 000000001ffd0000 - 000000001fff0c00 (reserved) BIOS-e820: 000000001fff0c00 - 000000001fffc000 (ACPI NVS) BIOS-e820: 000000001fffc000 - 0000000020000000 (reserved) 0MB HIGHMEM available. 511MB LOWMEM available. ACPI: have wakeup address 0xc0001000 On node 0 totalpages: 131024 zone(0): 4096 pages. zone(1): 126928 pages. zone(2): 0 pages. ACPI: RSDP (v000 COMPAQ ) @ 0x000f9970 ACPI: RSDT (v001 COMPAQ CPQ004A 12549.00544) @ 0x1fff0c84 ACPI: FADT (v002 COMPAQ CPQ004A 00000.00002) @ 0x1fff0c00 ACPI: SSDT (v001 COMPAQ CPQGysr 00000.04097) @ 0x1fff64c3 ACPI: SSDT (v001 COMPAQ CPQMag 00000.04097) @ 0x1fff65d1 ACPI: DSDT (v001 COMPAQ EVON800 00001.00000) @ 0x00000000 ACPI: BIOS passes blacklist ACPI: MADT not present Kernel command line: ro root=/dev/hda4 hdc=ide-scsi vga=794 ide_setup: hdc=ide-scsi No local APIC present or hardware disabled Initializing CPU#0 Detected 1794.206 MHz processor. Console: colour dummy device 80x25 Calibrating delay loop... 3578.26 BogoMIPS Memory: 514952k/524096k available (1422k kernel code, 8756k reserved, 514k data, 152k init, 0k highmem) Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) Inode cache hash table entries: 32768 (order: 6, 262144 bytes) Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes) Page-cache hash table entries: 131072 (order: 7, 524288 bytes) CPU: Before vendor init, caps: 3febf9ff 00000000 00000000, vendor = 0 CPU: L1 I cache: 0K, L1 D cache: 8K CPU: L2 cache: 512K CPU: After vendor init, caps: 3febf9ff 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: 3febf9ff 00000000 00000000 00000000 CPU: Common caps: 3febf9ff 00000000 00000000 00000000 CPU: Intel(R) Pentium(R) 4 Mobile CPU 1.80GHz stepping 04 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX mtrr: v1.40 (20010327) Richard Gooch (rgooch-r1x6VkxMR+00zabcByZE4g@public.gmane.org) mtrr: detected mtrr type: Intel ACPI: Subsystem revision 20020918 PCI: PCI BIOS revision 2.10 entry at 0xf031f, last bus=3 PCI: Using configuration type 1 ACPI-0274: *** Info: Table [DSDT] replaced by host OS ACPI-0107: *** Error: Acpi_load_tables: Could not load namespace: AE_AML_BAD_NAME ACPI-0116: *** Error: Acpi_load_tables: Could not load tables: AE_AML_BAD_NAME ACPI: Unable to load the System Description Tables PCI: Probing PCI hardware PCI: ACPI tables contain no PCI IRQ routing entries PCI: Probing PCI hardware (bus 00) Transparent bridge - Intel Corp. 82801BAM/CAM PCI Bridge PCI: Using IRQ router PIIX [8086/248c] at 00:1f.0 PCI: Found IRQ 10 for device 02:0e.1 PCI: Sharing IRQ 10 with 02:08.0 PCI: Sharing IRQ 10 with 02:0e.0 PCI: Sharing IRQ 10 with 02:0e.2 isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd VFS: Diskquotas version dquot_6.4.0 initialized vesafb: framebuffer at 0x48000000, mapped to 0xe0806000, size 65472k vesafb: mode is 1280x1024x16, linelength=2560, pages=24 vesafb: protected mode interface info at c000:561f vesafb: scrolling: redraw vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 160x64 fb0: VESA VGA frame buffer device pty: 2048 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS02 at 0x03e8 (irq = 4) is a 16550A Real Time Clock Driver v1.10e Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH3M: IDE controller on PCI bus 00 dev f9 PCI: Device 00:1f.1 not available because of resource collisions PCI: Assigned IRQ 11 for device 00:1f.1 ICH3M: BIOS setup was incomplete. ICH3M: chipset revision 2 ICH3M: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x4440-0x4447, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x4448-0x444f, BIOS settings: hdc:DMA, hdd:pio hda: IC25T060ATCS05-0, ATA DISK drive hdc: DW-28E, ATAPI CD/DVD-ROM drive ide2: ports already in use, skipping probe ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 blk: queue c0351184, I/O limit 4095Mb (mask 0xffffffff) hda: 117210240 sectors (60012 MB) w/1768KiB Cache, CHS=7752/240/63, UDMA(100) ide-floppy driver 0.99.newide Partition check: hda: hda1 hda2 hda3 < hda5 hda6 > hda4 Floppy drive(s): fd0 is 1.44M FDC 0 is a National Semiconductor PC87306 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Linux agpgart interface v0.99 (c) Jeff Hartmann agpgart: Maximum main memory to use for agp memory: 439M agpgart: Detected Intel i845 chipset agpgart: AGP aperture is 256M @ 0x60000000 ide-floppy driver 0.99.newide md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. RAMDISK: Compressed image found at block 0 Freeing initrd memory: 122k freed VFS: Mounted root (ext2 filesystem). Journalled Block Device driver loaded kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Freeing unused kernel memory: 152k freed Adding Swap: 529164k swap-space (priority -1) usb.c: registered new driver usbdevfs usb.c: registered new driver hub PCI: Found IRQ 10 for device 02:0e.0 PCI: Sharing IRQ 10 with 02:08.0 PCI: Sharing IRQ 10 with 02:0e.1 PCI: Sharing IRQ 10 with 02:0e.2 usb-ohci.c: USB OHCI at membase 0xe48bb000, IRQ 10 usb-ohci.c: usb-02:0e.0, NEC Corporation USB usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 3 ports detected PCI: Found IRQ 10 for device 02:0e.1 PCI: Sharing IRQ 10 with 02:08.0 PCI: Sharing IRQ 10 with 02:0e.0 PCI: Sharing IRQ 10 with 02:0e.2 usb-ohci.c: USB OHCI at membase 0xe48bd000, IRQ 10 usb-ohci.c: usb-02:0e.1, NEC Corporation USB (#2) usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 2 ports detected hub.c: new USB device 02:0e.1-1, assigned address 2 hub.c: USB hub found hub.c: 3 ports detected hub.c: new USB device 02:0e.1-2, assigned address 3 hub.c: USB hub found hub.c: 3 ports detected hub.c: new USB device 02:0e.1-2.1, assigned address 4 usb.c: USB device 4 (vend/prod 0x603/0x7134) is not claimed by any active driver. usb.c: registered new driver usb_mouse input0: USB Mouse STD. on usb2:4.0 usbmouse.c: v1.6:USB HID Boot Protocol mouse driver usb.c: registered new driver hiddev usb.c: registered new driver hid hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik hid-core.c: USB HID support drivers mice: PS/2 mouse device common for all mice EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,4), internal journal kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,2), internal journal EXT3-fs: mounted filesystem with ordered data mode. SCSI subsystem driver Revision: 1.00 scsi0 : SCSI host adapter emulation for IDE ATAPI devices Vendor: TEAC Model: DW-28E Rev: A.0B Type: CD-ROM ANSI SCSI revision: 02 hdc: DMA disabled parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP] parport0: irq 7 detected Linux Kernel Card Services 3.1.22 options: [pci] [cardbus] [pm] PCI: Found IRQ 11 for device 02:06.0 Yenta IRQ list 0298, PCI irq11 Socket status: 30000006 cs: IO port probe 0x0c00-0x0cff: clean. cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x4d0-0x4d7 cs: IO port probe 0x0a00-0x0aff: clean. parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP] parport0: irq 7 detected lp0: using parport0 (polling). lp0: console ready Thanks, Andreas