From: AnonimoVeneziano <voloterreno-nc/lrvXPQ4s@public.gmane.org>
To: acpi-devel-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org
Subject: Re: ACPI + IO-APIC power off by button problems
Date: Sun, 02 Mar 2003 21:59:36 +0100 [thread overview]
Message-ID: <3E6270B8.4070805@tin.it> (raw)
Hi, thank you
I post you my cat /proc/interrupts
CPU0 0: 18871 IO-APIC-edge timer
1: 689 IO-APIC-edge keyboard
2: 0 XT-PIC cascade
8: 1 IO-APIC-edge rtc
9: 0 IO-APIC-level acpi
12: 16103 IO-APIC-edge PS/2 Mouse
14: 3503 IO-APIC-edge ide0
15: 3148 IO-APIC-edge ide1
16: 4432 IO-APIC-level cmpci
19: 155 IO-APIC-level eth0
NMI: 0
LOC: 18823
ERR: 0
MIS: 0
I can't post my dmesg , or , better, it will be unuseful , because I use
Software RAID, and Software RAID makes very much output that delete the
first part of my dmesg (the part that you need). If this can be useful
to you when the system starts I see a message like "No IRQ Known for
device X.XX.X using IRQ 255 " and " try to start with option pci=noacpi"
or something like that.
I post you my lspci output if this can be of any help:
00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400 AGP] Host Bridge
Subsystem: VIA Technologies, Inc.: Unknown device 0000
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=32 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 89 31 06 00 30 22 00 00 00 06 00 08 00 00
10: 08 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 00 00
30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: dee00000-dfefffff
Prefetchable memory behind bridge: dad00000-decfffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 68 b1 07 01 30 22 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 f0 00 00 00
20: e0 de e0 df d0 da c0 de 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 0c 00
00:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at ec00 [size=256]
Region 1: Memory at dfffff00 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: ec 10 39 81 07 00 90 02 10 00 00 02 00 80 00 00
10: 01 ec 00 00 00 ff ff df 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 ec 10 39 81
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 20 40
00:0c.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev
10)
Subsystem: Micro-Star International Co., Ltd.: Unknown device 5900
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at e800 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: f6 13 11 01 05 00 10 02 10 00 01 04 00 80 00 00
10: 01 e8 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 62 14 00 59
30: 00 00 00 00 c0 00 00 00 00 00 00 00 0b 01 02 18
00:10.0 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00
[UHCI])
Subsystem: VIA Technologies, Inc. USB
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128, cache line size 08
Interrupt: pin A routed to IRQ 21
Region 4: I/O ports at dc00 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 17 00 10 02 80 00 03 0c 08 80 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 dc 00 00 00 00 00 00 00 00 00 00 06 11 38 30
30: 00 00 00 00 80 00 00 00 00 00 00 00 05 01 00 00
00:10.1 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00
[UHCI])
Subsystem: VIA Technologies, Inc. USB
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128, cache line size 08
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at e000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 17 00 10 02 80 00 03 0c 08 80 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 e0 00 00 00 00 00 00 00 00 00 00 06 11 38 30
30: 00 00 00 00 80 00 00 00 00 00 00 00 05 02 00 00
00:10.2 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00
[UHCI])
Subsystem: VIA Technologies, Inc. USB
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128, cache line size 08
Interrupt: pin C routed to IRQ 21
Region 4: I/O ports at e400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 17 00 10 02 80 00 03 0c 08 80 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 e4 00 00 00 00 00 00 00 00 00 00 06 11 38 30
30: 00 00 00 00 80 00 00 00 00 00 00 00 05 03 00 00
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if
20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128, cache line size 08
Interrupt: pin D routed to IRQ 21
Region 0: Memory at dffffe00 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 04 31 17 00 10 02 82 20 03 0c 08 80 00 00
10: 00 fe ff df 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 04 31
30: 00 00 00 00 80 00 00 00 00 00 00 00 0a 04 00 00
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
Subsystem: VIA Technologies, Inc.: Unknown device 0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 77 31 87 00 10 02 00 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 00 00
30: 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus
Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT8235 Bus Master ATA133/100/66/33 IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 255
Region 4: I/O ports at fc00 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 71 05 07 00 90 02 06 8a 01 01 00 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 fc 00 00 00 00 00 00 00 00 00 00 06 11 71 05
30: 00 00 00 00 c0 00 00 00 00 00 00 00 ff 01 00 00
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP
(rev 82) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G450 32Mb SDRAM Dual Head
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (4000ns min, 8000ns max), cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: Memory at dc000000 (32-bit, prefetchable) [size=32M]
Region 1: Memory at dfefc000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at df000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at dfec0000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x1
00: 2b 10 25 05 07 00 90 02 82 00 00 03 08 80 00 00
10: 08 00 00 dc 00 c0 ef df 00 00 00 df 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 2b 10 41 06
30: 00 00 ec df dc 00 00 00 00 00 00 00 0b 01 10 20
Thanks again
-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf
next reply other threads:[~2003-03-02 20:59 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-03-02 20:59 AnonimoVeneziano [this message]
[not found] ` <3E6270B8.4070805-nc/lrvXPQ4s@public.gmane.org>
2003-03-02 22:46 ` ACPI + IO-APIC power off by button problems Randy.Dunlap
-- strict thread matches above, loose matches on Subject: below --
2003-03-06 22:22 Grover, Andrew
[not found] ` <F760B14C9561B941B89469F59BA3A847E96CD2-sBd4vmA9Se4Lll3ZsUKC9FDQ4js95KgL@public.gmane.org>
2003-03-07 11:41 ` Sérgio Monteiro Basto
[not found] <C50AB9511EE59B49B2A503CB7AE1ABD10440E41B@cceexc19.americas.cpqcorp.net>
[not found] ` <C50AB9511EE59B49B2A503CB7AE1ABD10440E41B-Iar2LzuD2f6P0FQRY6S+e9kSKC0Mw0DFJ8am2ALHCgk@public.gmane.org>
2003-03-02 22:33 ` AnonimoVeneziano
[not found] ` <3E6286C3.1050504-nc/lrvXPQ4s@public.gmane.org>
2003-03-03 10:55 ` Faye Pearson
[not found] ` <20030303105554.GA12170-6JSjyQ0Qj1ReoWH0uzbU5w@public.gmane.org>
2003-03-05 22:54 ` Sérgio Monteiro Basto
[not found] ` <1046904893.1505.23.camel-4/PLUo9XfK/yXfm4dIG/yWZHpeb/A1Y/@public.gmane.org>
2003-03-06 11:12 ` Sérgio Monteiro Basto
2003-03-02 20:38 Cagle, John (ISS-Houston)
2003-03-02 18:53 AnonimoVeneziano
[not found] ` <3E62533A.7050505-nc/lrvXPQ4s@public.gmane.org>
2003-03-02 20:11 ` dbenham-FG1iuTdj8bisTnJN9+BGXg
[not found] ` <20030302201158.GA22010-FG1iuTdj8bisTnJN9+BGXg@public.gmane.org>
2003-03-02 20:07 ` AnonimoVeneziano
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3E6270B8.4070805@tin.it \
--to=voloterreno-nc/lrvxpq4s@public.gmane.org \
--cc=acpi-devel-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox