Linux version 2.6.9-rc2-mm4 (root@laptop) (gcc version 3.3.4 20040623 (Gentoo Linux 3.3.4-r1, ssp-3.3.2-2, pie-8.7.6)) #4 Wed Sep 29 18:47:30 CEST 2004 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fee0000 (usable) BIOS-e820: 000000001fee0000 - 000000001feec000 (ACPI data) BIOS-e820: 000000001feec000 - 000000001ff00000 (ACPI NVS) BIOS-e820: 000000001ff00000 - 0000000020000000 (reserved) BIOS-e820: 00000000fec10000 - 00000000fec20000 (reserved) BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved) BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved) 510MB LOWMEM available. On node 0 totalpages: 130784 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 126688 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 DMI present. ACPI: RSDP (v000 ACER ) @ 0x000f6020 ACPI: RSDT (v001 ACER TM8000 0x20020608 LTP 0x00000000) @ 0x1fee52ea ACPI: FADT (v001 ACER TM8000 0x20020608 PTL 0x00000050) @ 0x1feebf2c ACPI: HPET (v001 ACER TM8000 0x20020608 PTL 0x00000000) @ 0x1feebfa0 ACPI: BOOT (v001 ACER TM8000 0x20020608 LTP 0x00000001) @ 0x1feebfd8 ACPI: DSDT (v001 ACER TM8000 0x20020608 MSFT 0x0100000e) @ 0x00000000 ACPI: HPET id: 0x8086a201 base: 0x0 Built 1 zonelists Initializing CPU#0 Kernel command line: root=/dev/hda3 vga=791 PID hash table entries: 2048 (order: 11, 32768 bytes) Detected 1794.185 MHz processor. Using tsc for high-res timesource Console: colour dummy device 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 513224k/523136k available (3326k kernel code, 9428k reserved, 1162k data, 156k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 3547.13 BogoMIPS (lpj=1773568) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: afe9f9bf 00000000 00000000 00000000 CPU: After vendor identify, caps: afe9f9bf 00000000 00000000 00000000 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 2048K CPU: After all inits, caps: afe9f9bf 00000000 00000000 00000040 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: Intel(R) Pentium(R) M processor 1.80GHz stepping 06 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. ACPI: IRQ9 SCI: Edge set to Level Trigger. NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfd732, last bus=2 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040816 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs *6) ACPI: PCI Interrupt Link [LNKB] (IRQs *10) ACPI: PCI Interrupt Link [LNKC] (IRQs *6) ACPI: PCI Interrupt Link [LNKD] (IRQs *6) ACPI: PCI Interrupt Link [LNKE] (IRQs *10) ACPI: PCI Interrupt Link [LNKF] (IRQs 10) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 6) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs *10) ACPI: Embedded Controller [EC0] (gpe 29) ACPI: Power Resource [PFN0] (off) ACPI: Power Resource [PFN1] (off) SCSI subsystem initialized Linux Kernel Card Services options: [pci] [cardbus] [pm] usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing ** PCI interrupts are no longer routed automatically. If this ** causes a device to stop working, it is probably because the ** driver failed to call pci_enable_device(). As a temporary ** workaround, the "pci=routeirq" argument restores the old ** behavior. If this argument makes the device work again, ** please email the output of "lspci" to bjorn.helgaas-VXdhtT5mjnY@public.gmane.org ** so I can fix the driver. Simple Boot Flag at 0x37 set to 0x1 Machine check exception polling timer started. Installing knfsd (copyright (C) 1996 okir-pn4DOG8n3UYbFoVRYvo4fw@public.gmane.org). Initializing Cryptographic API vesafb: framebuffer at 0xd8000000, mapped to 0xe0880000, size 3072k vesafb: mode is 1024x768x16, linelength=2048, pages=84 vesafb: protected mode interface info at c000:588a vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device ACPI: AC Adapter [ACAD] (on-line) ACPI: Battery Slot [BAT1] (battery present) ACPI: Battery Slot [BAT2] (battery absent) ACPI: Power Button (FF) [PWRF] ACPI: Lid Switch [LID] ACPI: Sleep Button (CM) [SLPB] ACPI: Fan [FAN0] (off) ACPI: Fan [FAN1] (off) ACPI: Processor [CPU0] (supports C1 C2 C3, 8 throttling states) ACPI: Thermal Zone [THRM] (46 C) Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected an Intel 855GM Chipset. agpgart: Maximum main memory to use for agp memory: 438M agpgart: AGP aperture is 256M @ 0xe0000000 i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10 ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 10 (level, low) -> IRQ 10 loop: loaded (max 8 devices) pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe-l3A5Bk7waGM@public.gmane.org) and petero2-zq6IREYz3ykAvxtiuMwx3w@public.gmane.org tg3.c:v3.10 (September 14, 2004) ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 6 ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 6 (level, low) -> IRQ 6 eth0: Tigon3 [partno(BCM95705A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:c0:9f:44:d4:77 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH4: IDE controller at PCI slot 0000:00:1f.1 PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 6 ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 6 (level, low) -> IRQ 6 ICH4: chipset revision 3 ICH4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x1860-0x1867, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x1868-0x186f, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: IC25N080ATMR04-0, ATA DISK drive Using anticipatory io scheduler ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: MATSHITADVD-RAM UJ-820S, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 Probing IDE interface ide2... ide2: Wait for ready failed before probe ! Probing IDE interface ide3... ide3: Wait for ready failed before probe ! Probing IDE interface ide4... ide4: Wait for ready failed before probe ! Probing IDE interface ide5... ide5: Wait for ready failed before probe ! hda: max request size: 1024KiB hda: 156301488 sectors (80026 MB) w/7884KiB Cache, CHS=16383/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 ohci1394: $Rev: 1226 $ Ben Collins ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 10 (level, low) -> IRQ 10 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[d0218000-d02187ff] Max Packet=[2048] ieee1394: raw1394: /dev/raw1394 device initialized sbp2: $Rev: 1231 $ Ben Collins ACPI: PCI interrupt 0000:02:06.0[A] -> GSI 6 (level, low) -> IRQ 6 Yenta: CardBus bridge found at 0000:02:06.0 [1025:0051] Yenta: ISA IRQ mask 0x08b8, PCI irq 6 Socket status: 30000006 ACPI: PCI interrupt 0000:02:06.1[A] -> GSI 6 (level, low) -> IRQ 6 Yenta: CardBus bridge found at 0000:02:06.1 [1025:0051] Yenta: ISA IRQ mask 0x08b8, PCI irq 6 Socket status: 30000006 PCI: Enabling device 0000:02:06.3 (0080 -> 0082) ACPI: PCI interrupt 0000:02:06.3[A] -> GSI 6 (level, low) -> IRQ 6 Yenta: CardBus bridge found at 0000:02:06.3 [1025:0051] Yenta: ISA IRQ mask 0x08b8, PCI irq 6 Socket status: 30000410 ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10 ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 10 (level, low) -> IRQ 10 ehci_hcd 0000:00:1d.7: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB 2.0 EHCI Controller PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: irq 10, pci mem 0xd0000000 ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected USB Universal Host Controller Interface driver v2.2 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 6 ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 6 (level, low) -> IRQ 6 uhci_hcd 0000:00:1d.0: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 ieee1394: Host added: ID:BUS[0-00:1023] GUID[00c09f00001ca1bf] PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: irq 6, io base 0x1800 uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 6 (level, low) -> IRQ 6 uhci_hcd 0000:00:1d.1: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: irq 6, io base 0x1820 uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 usb 1-6: new high speed USB device using address 2 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 6 (level, low) -> IRQ 6 uhci_hcd 0000:00:1d.2: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 hub 1-6:1.0: USB hub found hub 1-6:1.0: 4 ports detected PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: irq 6, io base 0x1840 uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.0:USB HID core driver mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard on isa0060/serio0 Synaptics Touchpad, model: 1 Firmware: 5.8 180 degree mounted touchpad Sensor: 29 new absolute packet format Touchpad has extended capability bits -> 4 multi-buttons, i.e. besides standard buttons -> multifinger detection -> palm detection input: SynPS/2 Synaptics TouchPad on isa0060/serio4 i2c /dev entries driver Advanced Linux Sound Architecture Driver Version 1.0.6 (Sun Aug 15 07:17:53 2004 UTC). ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1f.5 to 64 intel8x0_measure_ac97_clock: measured 49517 usecs intel8x0: clocking to 48000 ALSA device list: #0: Intel 82801DB-ICH4 with ALC202 at 0xd0000c00, irq 10 NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) ip_conntrack version 2.1 (4087 buckets, 32696 max) - 176 bytes per conntrack ip_tables: (C) 2000-2002 Netfilter core team ipt_recent v0.3.1: Stephen Frost . http://snowman.net/projects/ipt_recent/ arp_tables: (C) 2002 David S. Miller NET: Registered protocol family 1 NET: Registered protocol family 17 cpufreq: CPU0 - ACPI performance management activated. cpufreq: *P0: 1800 MHz, 24000 mW, 10 uS cpufreq: P1: 1600 MHz, 20000 mW, 10 uS cpufreq: P2: 1400 MHz, 18000 mW, 10 uS cpufreq: P3: 1000 MHz, 16000 mW, 10 uS cpufreq: P4: 600 MHz, 12000 mW, 10 uS ACPI: (supports S0 S3 S4 S5) ACPI wakeup devices: GLAN MPCI T394 MDM0 USB1 USB2 USB3 VFS: Mounted root (reiser4 filesystem) readonly. Freeing unused kernel memory: 156k freed Adding 506036k swap on /dev/hda2. Priority:-1 extents:1 ieee80211_crypt: registered algorithm 'NULL' ipw2200: Intel(R) PRO/Wireless 2200 Network Driver, 0.9 ipw2200: Copyright(c) 2003-2004 Intel Corporation ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10 ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 10 (level, low) -> IRQ 10 ipw2200: Calibration tg3: eth0: Link is up at 100 Mbps, full duplex. tg3: eth0: Flow control is on for TX and on for RX. ipw2200: Calibration ipw2200: I ipw_irq_tasklet RF_KILL_DONE ipw2200: U ipw_rf_kill RF Kill active, rescheduling GPIO check ipw2200: U ipw_rf_kill RF Kill active, rescheduling GPIO check ipw2200: U ipw_rf_kill RF Kill no longer active, restarting device ipw2200: Calibration mtrr: 0xd8000000,0x8000000 overlaps existing 0xd8000000,0x200000 No module found in object