From: Janosch Machowinski <scotch-cGBD8117FJM@public.gmane.org>
To: Bruno Ducrot <ducrot-kk6yZipjEM5g9hUCZPvPmw@public.gmane.org>
Cc: linux-acpi-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Subject: Re: Strange interpreter behaviour
Date: Mon, 16 Jan 2006 22:27:28 +0100 [thread overview]
Message-ID: <43CC0FC0.9090806@tzi.de> (raw)
In-Reply-To: <20060116171932.GF25115-kk6yZipjEM5g9hUCZPvPmw@public.gmane.org>
> Sound like \_SB.INV7 is a bit into a GPIO.
> More, the associated OR is defined like that:
> OperationRegion (GPIO, SystemIO, IO2B, 0x40)
>
> Note that IO2B is given here:
> OperationRegion (BIOS, SystemMemory, 0x1FF50064, 0xFF)
> Field (BIOS, ByteAcc, NoLock, Preserve)
> {
> SS1, 1,
> SS2, 1,
> SS3, 1,
> SS4, 1,
> Offset (0x01),
> IOST, 16,
> SPIO, 16,
> PMBS, 16,
> PMLN, 8,
> SMBS, 16,
> SMLN, 8,
> IO1B, 16,
> IO1L, 8,
> IO2B, 16,
> IO2L, 8,
> TOPM, 32,
> ROMS, 32,
>
> Therefore one think to check is that IO2B is set correctly to point to
> the GPIO's, then look if the GPIO is configured as a GPO (not as a GPI).
>
> For checking if IO2B is correct:
> sudo dd if=/dev/mem bs=1c skip=536150130 count=2 | hexdump
>
Here it get's strange :
scotchmobil scotch # dd if=/dev/mem bs=1c skip=536150130 count=2
dd: reading `/dev/mem': Bad address
0+0 records in
0+0 records out
> ./acpixtract FACP < acpidump.out | ./acpitbl
>
> where acpidump.txt is the output from ./acpidump. I assume you know
> what I'm talking about reading the bugzilla report, or else do something
> like that:
>
> wget ftp://ftp.kernel.org//pub/linux/kernel/people/lenb/acpi/utils/pmtools-20050926.tar.bz2
> tar xjvfp pmtools-20050926.tar.bz2
> cd pmtools
> make
> cd acpidump
> sudo ./acpidmp > acpidmp.out
>
> I think the value given by the 'sudo dd' above should correspond to the
> GPE0_BLK: field from the ./acpitbl above.
>
> For checking if the register where the INV7 is defined is configured as
> a GPO, well I have to know the ouput from 'lspci -v -xxx -s"the southbridge"'
>
Uhm as far as I know "the southbridge" is is the Intel 82801. There are
more than one 82801 devices, so I just post all except the USB devices,
sorry for that :
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 83)
(prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 00001000-00001fff
Memory behind bridge: ff900000-ff9fffff
Prefetchable memory behind bridge: dea00000-deafffff
00: 86 80 48 24 07 01 80 80 83 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 02 02 40 10 10 80 02
20: 90 ff 90 ff a0 de a0 de 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 06 00
40: 02 28 20 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 02 74 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 40 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 03 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 10 00 08 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 01 00 02 00 00 00 c0 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 60 0f 00 00 00 00 2c 48
00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface
Bridge (rev 03)
Flags: bus master, medium devsel, latency 0
00: 86 80 cc 24 0f 01 80 02 03 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 01 04 00 00 10 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 01 05 00 00 10 00 00 00
60: 0b 04 0a 05 90 00 00 00 80 80 80 0a 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: ff fc 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 28 03 00 00 00 00 00 00 0d 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 80 02 02 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 02 28 00 00 02 cf 00 00 04 00 00 00 00 00 00 00
e0: 12 00 00 c0 00 00 06 34 33 22 11 00 00 00 67 45
f0: 00 00 01 00 00 00 00 00 60 0f 03 00 00 00 80 02
00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE
Controller (rev 03) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Unknown device 1869
Flags: bus master, medium devsel, latency 0, IRQ 10
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at ffa0 [size=16]
Memory at 30000000 (32-bit, non-prefetchable) [size=1K]
00: 86 80 ca 24 07 00 80 02 03 8a 01 01 00 00 00 00
10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00
20: a1 ff 00 00 00 00 00 30 00 00 00 00 43 10 69 18
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00
40: 07 e3 07 e3 00 00 00 00 05 00 01 02 00 00 00 00
50: 00 00 00 00 31 14 00 00 00 00 00 00 00 00 00 00
60: 08 00 00 00 00 00 00 00 08 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 60 0f 00 00 00 00 00 00
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
SMBus Controller (rev 03)
Subsystem: ASUSTeK Computer Inc. Unknown device 1869
Flags: medium devsel
I/O ports at 0540 [size=32]
00: 86 80 c3 24 01 00 80 02 03 00 05 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 41 05 00 00 00 00 00 00 00 00 00 00 43 10 69 18
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 02 00 00
40: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 60 0f 00 00 00 00 00 00
-
To unsubscribe from this list: send the line "unsubscribe linux-acpi" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2006-01-16 21:27 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-01-07 17:18 Strange interpreter behaviour Janosch Machowinski
[not found] ` <43BFF7DE.1000909-cGBD8117FJM@public.gmane.org>
2006-01-16 17:19 ` Bruno Ducrot
[not found] ` <20060116171932.GF25115-kk6yZipjEM5g9hUCZPvPmw@public.gmane.org>
2006-01-16 21:27 ` Janosch Machowinski [this message]
[not found] ` <43CC0FC0.9090806-cGBD8117FJM@public.gmane.org>
2006-01-17 10:30 ` Bruno Ducrot
[not found] ` <20060117103043.GA2154-kk6yZipjEM5g9hUCZPvPmw@public.gmane.org>
2006-01-17 12:41 ` Janosch Machowinski
[not found] ` <43CCE603.3010600-cGBD8117FJM@public.gmane.org>
2006-01-17 13:24 ` Bruno Ducrot
[not found] ` <20060117132435.GB2154-kk6yZipjEM5g9hUCZPvPmw@public.gmane.org>
2006-01-17 14:28 ` Janosch Machowinski
[not found] ` <43CCFF1C.4000309-cGBD8117FJM@public.gmane.org>
2006-01-17 15:47 ` Bruno Ducrot
2006-01-20 15:27 ` Janosch Machowinski
2006-01-20 19:32 ` Bruno Ducrot
2006-01-21 18:55 ` Janosch Machowinski
-- strict thread matches above, loose matches on Subject: below --
2006-01-09 5:58 Yu, Luming
2006-01-09 7:16 ` Janosch Machowinski
2006-01-16 2:27 Yu, Luming
2006-01-16 19:22 ` Janosch Machowinski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=43CC0FC0.9090806@tzi.de \
--to=scotch-cgbd8117fjm@public.gmane.org \
--cc=ducrot-kk6yZipjEM5g9hUCZPvPmw@public.gmane.org \
--cc=linux-acpi-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox