Linux version 2.6.22.1-20.fc7 (kojibuilder@xenbuilder2.fedora.redhat.com) (gcc version 4.1.2 20070502 (Red Hat 4.1.2-12)) #1 SMP Thu Jul 12 19:40:48 EDT 2007 Command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009dc00 (usable) BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000ce000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000037e70000 (usable) BIOS-e820: 0000000037e70000 - 0000000037e80000 (ACPI data) BIOS-e820: 0000000037e80000 - 0000000037f00000 (ACPI NVS) BIOS-e820: 0000000037f00000 - 0000000040000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) Entering add_active_range(0, 0, 157) 0 entries of 3200 used Entering add_active_range(0, 256, 228976) 1 entries of 3200 used end_pfn_map = 1048576 DMI present. ACPI: RSDP 000F8500, 0014 (r0 PTLTD ) ACPI: RSDT 37E7956A, 0040 (r1 DELL M08 6040000 LTP 0) ACPI: FACP 37E7FB9A, 0074 (r1 ATI Bowfin 6040000 ATI F4240) ACPI: DSDT 37E795AA, 65F0 (r1 ATI SB600 6040000 MSFT 3000000) ACPI: FACS 37E90FC0, 0040 ACPI: TCPA 37E7FC0E, 0032 (r2 AMD 6040000 PTEC 0) ACPI: SSDT 37E7FC40, 0182 (r1 PTLTD POWERNOW 6040000 LTP 1) ACPI: APIC 37E7FDC2, 0054 (r1 PTLTD APIC 6040000 LTP 0) ACPI: MCFG 37E7FE16, 003C (r1 PTLTD MCFG 6040000 LTP 0) ACPI: HPET 37E7FE52, 0038 (r1 PTLTD HPETTBL 6040000 LTP 1) ACPI: SLIC 37E7FE8A, 0176 (r1 DELL M08 6040000 LTP 0) Scanning NUMA topology in Northbridge 24 No NUMA configuration found Faking a node at 0000000000000000-0000000037e70000 Entering add_active_range(0, 0, 157) 0 entries of 3200 used Entering add_active_range(0, 256, 228976) 1 entries of 3200 used Bootmem setup node 0 0000000000000000-0000000037e70000 Zone PFN ranges: DMA 0 -> 4096 DMA32 4096 -> 1048576 Normal 1048576 -> 1048576 early_node_map[2] active PFN ranges 0: 0 -> 157 0: 256 -> 228976 On node 0 totalpages: 228877 DMA zone: 56 pages used for memmap DMA zone: 1302 pages reserved DMA zone: 2639 pages, LIFO batch:0 DMA32 zone: 3074 pages used for memmap DMA32 zone: 221806 pages, LIFO batch:31 Normal zone: 0 pages used for memmap ATI board detected. Disabling timer routing over 8254. ACPI: PM-Timer IO Port: 0x8008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 (Bootup-CPU) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 ACPI: IRQ9 used by override. Setting APIC routing to flat ACPI: HPET id: 0x43538301 base: 0xfed00000 Using ACPI (MADT) for SMP configuration information swsusp: Registered nosave memory region: 000000000009d000 - 000000000009e000 swsusp: Registered nosave memory region: 000000000009e000 - 00000000000a0000 swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000ce000 swsusp: Registered nosave memory region: 00000000000ce000 - 0000000000100000 Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) SMP: Allowing 2 CPUs, 0 hotplug CPUs PERCPU: Allocating 40968 bytes of per cpu data Built 1 zonelists. Total pages: 224445 Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) Marking TSC unstable due to TSCs unsynchronized time.c: Detected 1596.008 MHz processor. Console: colour VGA+ 80x25 Checking aperture... CPU 0: aperture @ 5b88000000 size 32 MB Aperture too small (32 MB) No AGP bridge found Memory: 893752k/915904k available (2366k kernel code, 21756k reserved, 1401k data, 312k init) SLUB: Genslabs=23, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1 Calibrating delay using timer specific routine.. 3194.24 BogoMIPS (lpj=1597124) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU 0/0 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 SMP alternatives: switching to UP code ACPI: Core revision 20070126 ..MP-BIOS bug: 8254 timer not connected to IO-APIC Using local APIC timer interrupts. result 12468826 Detected 12.468 MHz APIC timer. SMP alternatives: switching to SMP code Booting processor 1/2 APIC 0x1 Initializing CPU#1 Calibrating delay using timer specific routine.. 3191.96 BogoMIPS (lpj=1595981) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU 1/1 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 AMD Turion(tm) 64 X2 Mobile Technology TL-52 stepping 02 Brought up 2 CPUs sizeof(vma)=176 bytes sizeof(page)=56 bytes sizeof(inode)=560 bytes sizeof(dentry)=208 bytes sizeof(ext3inode)=760 bytes sizeof(buffer_head)=104 bytes sizeof(skbuff)=232 bytes sizeof(task_struct)=2048 bytes NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG at e0000000 - e09fffff PCI: No mmconfig possible on device 00:18 ACPI: System BIOS is requesting _OSI(Linux) ACPI: Please test with "acpi_osi=!Linux" Please send dmidecode to linux-acpi@vger.kernel.org ACPI: Interpreter enabled ACPI: (supports S0 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: Transparent bridge - 0000:00:14.4 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB5_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB6_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 11 devices ACPI: ACPI bus type pnp unregistered usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Cannot allocate resource region 7 of bridge 0000:00:05.0 PCI: Cannot allocate resource region 8 of bridge 0000:00:05.0 NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0 hpet0: 4 32-bit timers, 14318180 Hz ACPI: RTC can wake from S4 pnp: 00:01: iomem range 0xe0000000-0xefffffff could not be reserved pnp: 00:01: iomem range 0xfec00000-0xfec00fff could not be reserved pnp: 00:01: iomem range 0xfee00000-0xfee00fff could not be reserved pnp: 00:08: ioport range 0x1080-0x1080 has been reserved pnp: 00:08: ioport range 0x220-0x22f has been reserved pnp: 00:09: iomem range 0xe0000-0xfffff could not be reserved pnp: 00:09: iomem range 0xfff00000-0xffffffff could not be reserved pnp: 00:09: iomem range 0xc0004800-0xc0004bff has been reserved pnp: 00:09: iomem range 0xfed00000-0xfed003ff has been reserved PCI: Bridge: 0000:00:01.0 IO window: 9000-9fff MEM window: c0100000-c01fffff PREFETCH window: c8000000-cfffffff PCI: Bridge: 0000:00:05.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:06.0 IO window: disabled. MEM window: c0200000-c02fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:14.4 IO window: disabled. MEM window: c0300000-c03fffff PREFETCH window: disabled. PCI: Setting latency timer of device 0000:00:05.0 to 64 PCI: Setting latency timer of device 0000:00:06.0 to 64 NET: Registered protocol family 2 Time: hpet clocksource has been installed. IP route cache hash table entries: 32768 (order: 6, 262144 bytes) TCP established hash table entries: 131072 (order: 9, 3145728 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered checking if image is initramfs... it is Freeing initrd memory: 3754k freed audit: initializing netlink socket (disabled) audit(1184672762.632:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) SELinux: Registering netfilter hooks ksign: Installing public key data Loading keyring - Added public key 1D871FA41536D38E - User ID: Red Hat, Inc. (Kernel Module GPG key) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) PCI: MSI quirk detected. MSI deactivated. Boot video device is 0000:01:05.0 PCI: Setting latency timer of device 0000:00:05.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:05.0:pcie00] Allocate Port Service[0000:00:05.0:pcie02] PCI: Setting latency timer of device 0000:00:06.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:06.0:pcie00] Allocate Port Service[0000:00:06.0:pcie02] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: Thermal Zone [THRM] (61 C) hpet_resources: 0xfed00000 is busy Generic RTC Driver v1.07 Non-volatile memory driver v1.2 Linux agpgart interface v0.102 (c) Dave Jones Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize input: Macintosh mouse button emulation as /class/input/input0 PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input1 usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 powernow-k8: Found 2 AMD Turion(tm) 64 X2 Mobile Technology TL-52 processors (version 2.00.00) powernow-k8: 0 : fid 0x8 (1600 MHz), vid 0x13 powernow-k8: 1 : fid 0x0 (800 MHz), vid 0x1e drivers/rtc/hctosys.c: unable to open rtc device (rtc0) Freeing unused kernel memory: 312k freed Write protecting the kernel read-only data: 1060k USB Universal Host Controller Interface driver v3.0 ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 16 ohci_hcd 0000:00:13.0: OHCI Host Controller ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:13.0: irq 16, io mem 0xc0005000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 17 (level, low) -> IRQ 17 ohci_hcd 0000:00:13.1: OHCI Host Controller ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:13.1: irq 17, io mem 0xc0006000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 18 ohci_hcd 0000:00:13.2: OHCI Host Controller ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:13.2: irq 18, io mem 0xc0007000 Synaptics Touchpad, model: 1, fw: 6.3, id: 0x180b1, caps: 0xa04713/0x200000 input: SynPS/2 Synaptics TouchPad as /class/input/input2 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:13.3[B] -> GSI 17 (level, low) -> IRQ 17 ohci_hcd 0000:00:13.3: OHCI Host Controller ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 4 ohci_hcd 0000:00:13.3: irq 17, io mem 0xc0008000 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level, low) -> IRQ 18 ohci_hcd 0000:00:13.4: OHCI Host Controller ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 5 ohci_hcd 0000:00:13.4: irq 18, io mem 0xc0009000 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level, low) -> IRQ 19 ehci_hcd 0000:00:13.5: EHCI Host Controller ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 6 ehci_hcd 0000:00:13.5: debug port 1 ehci_hcd 0000:00:13.5: irq 19, io mem 0xc0004400 ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 10 ports detected SCSI subsystem initialized libata version 2.21 loaded. ahci 0000:00:12.0: version 2.2 ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 22 ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode ahci 0000:00:12.0: flags: ncq ilck led clo pmp pio scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci ata1: SATA max UDMA/133 cmd 0xffffc200001f8100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 22 ata2: SATA max UDMA/133 cmd 0xffffc200001f8180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 22 ata3: SATA max UDMA/133 cmd 0xffffc200001f8200 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 22 ata4: SATA max UDMA/133 cmd 0xffffc200001f8280 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 22 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATA-7: Hitachi HTS541680J9SA00, SB2OC74P, max UDMA/100 ata1.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/100 ata2: SATA link down (SStatus 0 SControl 300) ata3: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54168 SB2O PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sd 0:0:0:0: [sda] Attached SCSI disk ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:14.1 to 64 scsi4 : pata_atiixp scsi5 : pata_atiixp ata5: PATA max UDMA/100 cmd 0x00000000000101f0 ctl 0x00000000000103f6 bmdma 0x0000000000018420 irq 14 ata6: PATA max UDMA/100 cmd 0x0000000000010170 ctl 0x0000000000010376 bmdma 0x0000000000018428 irq 15 ata5.00: ATAPI: TSSTcorp DVD+/-RW TS-L632D, DE04, max UDMA/33 ata5.00: configured for UDMA/33 scsi 4:0:0:0: CD-ROM TSSTcorp DVD+-RW TS-L632D DE04 PQ: 0 ANSI: 5 device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. SELinux: Disabled at runtime. SELinux: Unregistering netfilter hooks audit(1184672773.196:2): selinux=0 auid=4294967295 sd 0:0:0:0: Attached scsi generic sg0 type 0 scsi 4:0:0:0: Attached scsi generic sg1 type 5 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0 rtc0: alarms up to one month sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 4:0:0:0: Attached scsi CD-ROM sr0 b44.c:v1.01 (Jun 16, 2006) ACPI: PCI Interrupt 0000:08:00.0[A] -> GSI 21 (level, low) -> IRQ 21 eth0: Broadcom 4400 10/100BaseT Ethernet 00:15:c5:c1:ab:b8 sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci: SDHCI controller found at 0000:08:01.0 [1180:0822] (rev 19) ACPI: PCI Interrupt 0000:08:01.0[B] -> GSI 20 (level, low) -> IRQ 20 mmc0: SDHCI at 0xc0302800 irq 20 DMA ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16 loop: module loaded floppy0: no floppy controllers found lp: driver loaded but no devices found NET: Registered protocol family 10 lo: Disabled Privacy Extensions Mobile IPv6 ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 17 (level, low) -> IRQ 17 ACPI: AC Adapter [ACAD] (on-line) ACPI: Battery Slot [BAT1] (battery present) No dock devices found. input: Power Button (FF) as /class/input/input3 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input4 ACPI: Power Button (CM) [PWRB] input: Sleep Button (CM) as /class/input/input5 ACPI: Sleep Button (CM) [SLPB] input: Lid Switch as /class/input/input6 ACPI: Lid Switch [LID] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no) device-mapper: multipath: version 1.0.5 loaded EXT3 FS on dm-0, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. Adding 1802232k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:1802232k ndiswrapper version 1.47 loaded (smp=yes) ndiswrapper (link_pe_images:576): fixing KI_USER_SHARED_DATA address in the driver ndiswrapper: driver bcmwl5 (Broadcom,10/12/2006, 4.100.15.5) loaded ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:05:00.0 to 64 ndiswrapper: using IRQ 18 eth1: ethernet device 00:16:cf:c9:da:2a using NDIS driver: bcmwl5, version: 0x4640f05, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 14E4:4312.5.conf eth1: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK usbcore: registered new interface driver ndiswrapper audit(1184672813.776:3): audit_pid=2209 old=0 by auid=4294967295 i2c /dev entries driver ADDRCONF(NETDEV_UP): eth1: link is not ready ADDRCONF(NETDEV_UP): eth0: link is not ready APIC error on CPU1: 00(40) ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready eth1: no IPv6 routers present APIC error on CPU1: 40(40) APIC error on CPU1: 40(40) APIC error on CPU1: 40(40) APIC error on CPU1: 40(40)