linux-acpi.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Al Stone <al.stone@linaro.org>
To: Hanjun Guo <hanjun.guo@linaro.org>, linux-acpi@vger.kernel.org
Cc: linaro-acpi@lists.linaro.org, patches@linaro.org,
	linaro-kernel@lists.linaro.org
Subject: Re: [PATCH v2 2/6] ACPI: bus master reload not supported in reduced HW mode
Date: Wed, 27 Nov 2013 15:35:53 -0700	[thread overview]
Message-ID: <529673C9.5050206@linaro.org> (raw)
In-Reply-To: <528ECA31.80101@linaro.org>

On 11/21/2013 08:06 PM, Hanjun Guo wrote:
> On 2013-11-22 8:41, al.stone@linaro.org wrote:
>> From: Al Stone <al.stone@linaro.org>
>>
>> Remove the saving and restoring of bus master reload registers in
>> suspend/resume when in reduced HW mode; according to the spec, no
>> such registers should exist
>>
>> Signed-off-by: Al Stone <al.stone@linaro.org>
>> ---
>>   drivers/acpi/processor_idle.c | 8 ++++++--
>>   1 file changed, 6 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/acpi/processor_idle.c b/drivers/acpi/processor_idle.c
>> index 597cdab..b18e7ab 100644
>> --- a/drivers/acpi/processor_idle.c
>> +++ b/drivers/acpi/processor_idle.c
>> @@ -202,7 +202,7 @@ static void lapic_timer_state_broadcast(struct acpi_processor *pr,
>>
>>   #endif
>>
>> -#ifdef CONFIG_PM_SLEEP
>> +#if (IS_ENABLED(CONFIG_PM_SLEEP) && !IS_ENABLED(CONFIG_ACPI_REDUCED_HARDWARE))
>>   static u32 saved_bm_rld;
>>
>>   static int acpi_processor_suspend(void)
>> @@ -236,7 +236,11 @@ void acpi_processor_syscore_exit(void)
>>   {
>>   	unregister_syscore_ops(&acpi_processor_syscore_ops);
>>   }
>> -#endif /* CONFIG_PM_SLEEP */
>
> I think the code below is not needed, because acpi_processor_suspend/resume()
> are not used by anywhere else.
>
>> +#else
>> +/* Bus master reload is not supported in reduced HW mode. */
>> +static int acpi_processor_suspend(void) { return 0; }
>> +static void acpi_processor_resume(void) { return; }
>> +#endif
>
> Thanks
> Hanjun
>

Agreed.  Removed in next version.

-- 
ciao,
al
-----------------------------------
Al Stone
Software Engineer
Linaro Enterprise Group
al.stone@linaro.org
-----------------------------------

  reply	other threads:[~2013-11-27 22:35 UTC|newest]

Thread overview: 25+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2013-11-22  0:41 [PATCH v2 0/6] Hardware Reduced Mode cleanup for ACPI al.stone
     [not found] ` < 528F9C65.7010302@linaro.org>
     [not found]   ` < CAOesGMgFBRjO++JSP0ddKKQ2RfG8V4fb97Hd+Oqwixi_Tt7Qwg@mail.gmail.com>
2013-11-22  0:41 ` [PATCH v2 1/6] ACPI: introduce CONFIG_ACPI_REDUCED_HARDWARE to enable this ACPI mode al.stone
2013-11-22  0:41 ` [PATCH v2 2/6] ACPI: bus master reload not supported in reduced HW mode al.stone
2013-11-22  3:06   ` Hanjun Guo
2013-11-27 22:35     ` Al Stone [this message]
2013-11-22  0:41 ` [PATCH v2 3/6] ACPI: HW reduced mode does not allow use of the FADT sci_interrupt field al.stone
2013-11-22  0:41 ` [PATCH v2 4/6] ACPI: ARM: exclude DMI calls al.stone
2013-11-22 13:25   ` Rob Herring
2013-11-22 18:03     ` Al Stone
2013-11-22 18:53       ` Olof Johansson
2013-11-22 23:15         ` Rafael J. Wysocki
2013-11-23  0:05           ` Al Stone
2013-11-23 16:38             ` Matthew Garrett
2013-11-25  5:10               ` Zheng, Lv
2013-11-25 15:30                 ` Matthew Garrett
2013-11-25 17:43                   ` Al Stone
2013-11-25 17:45                     ` Matthew Garrett
2013-11-25 18:01                       ` Al Stone
2013-12-04  1:30                         ` Al Stone
2013-12-04  1:34                           ` Matthew Garrett
2013-12-10 12:45               ` Grant Likely
2013-11-22  0:41 ` [PATCH v2 5/6] ACPI: do not reserve memory regions for some FADT entries in HW reduced mode al.stone
2013-11-22  0:41 ` [PATCH v2 6/6] ACPI: in HW reduced mode, using FADT PM information is not allowed al.stone
2013-11-22 23:18 ` [PATCH v2 0/6] Hardware Reduced Mode cleanup for ACPI Rafael J. Wysocki
2013-11-22 23:33   ` Al Stone

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=529673C9.5050206@linaro.org \
    --to=al.stone@linaro.org \
    --cc=hanjun.guo@linaro.org \
    --cc=linaro-acpi@lists.linaro.org \
    --cc=linaro-kernel@lists.linaro.org \
    --cc=linux-acpi@vger.kernel.org \
    --cc=patches@linaro.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).