Re: ARM juno R2 board USB Issue (EHCI probe failed)

From: Robin Murphy <robin.murphy@arm.com>
To: Hanjun Guo <hanjun.guo@linaro.org>,
	Sudeep Holla <sudeep.holla@arm.com>,
	"Sajjan, Vikas C" <vikas.cha.sajjan@hpe.com>,
	Vikas Sajjan <sajjan.linux@gmail.com>,
	"linux-usb@vger.kernel.org" <linux-usb@vger.kernel.org>,
	"linux-arm-kernel@lists.infradead.org"
	<linux-arm-kernel@lists.infradead.org>,
	"linux-acpi@vger.kernel.org" <linux-acpi@vger.kernel.org>
Cc: "mark.rutland@arm.com" <mark.rutland@arm.com>,
	"lorenzo.pieralisi@arm.com" <lorenzo.pieralisi@arm.com>
Subject: Re: ARM juno R2 board USB Issue (EHCI probe failed)
Date: Tue, 27 Sep 2016 17:23:29 +0100	[thread overview]
Message-ID: <9b231601-2c6a-a5d7-471f-4fc0d8190d83@arm.com> (raw)
In-Reply-To: <57EA9AAA.5090504@linaro.org>

On 27/09/16 17:13, Hanjun Guo wrote:
> On 09/27/2016 05:07 PM, Sudeep Holla wrote:
>>
>>
>> On 27/09/16 09:55, Sajjan, Vikas C wrote:
>>> Hi Sudeep,
>>>
>>> -----Original Message-----
>>> From: Sudeep Holla [mailto:sudeep.holla@arm.com]
>>> Sent: Tuesday, September 27, 2016 2:21 PM
>>> To: Vikas Sajjan <sajjan.linux@gmail.com>; linux-usb@vger.kernel.org;
>>> linux-arm-kernel@lists.infradead.org; linux-acpi@vger.kernel.org
>>> Cc: Sudeep Holla <sudeep.holla@arm.com>; mark.rutland@arm.com;
>>> lorenzo.pieralisi@arm.com; Sajjan, Vikas C <vikas.cha.sajjan@hpe.com>
>>> Subject: Re: ARM juno R2 board USB Issue (EHCI probe failed)
>>>
>>> Hi Vikas,
>>>
>>> On 27/09/16 09:14, Vikas Sajjan wrote:
>>>> Adding USB mailing list.
>>>>
>>>>
>>>> On Tue, Sep 27, 2016 at 12:33 PM, Sajjan, Vikas C
>>>> <vikas.cha.sajjan@hpe.com> wrote:
>>>>> Hi All,
>>>>>
>>>>> I working on ARM juno R2 board, with latest kernel 4.8.rc7 and I get
>>>>> below USB EHCI probe error while booting with acpi=force.
>>>>>
>>>
>>> Are you using the latest UEFI EDK2 ?
>>> No, I am still using the UEFI binary which came as part of the Juno
>>> board.
>>>
>>>
>>>>> [    1.223662] VFIO - User Level meta-driver version: 0.3
>>>>> [    1.229335] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
>>>>> Driver
>>>>> [    1.235882] ehci-pci: EHCI PCI platform driver
>>>>> [    1.240359] ehci-platform: EHCI generic platform driver
>>>>> [    1.245619] ehci-platform ARMH0D20:00: Error: DMA mask
>>>>> configuration failed
>>>>> [    1.272491] ehci-platform: probe of ARMH0D20:00 failed with
>>>>> error -5
>>>>> [    1.278876] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
>>>>> [    1.285071] ohci-pci: OHCI PCI platform driver
>>>>> [    1.289548] ohci-platform: OHCI generic platform driver
>>>>> [    1.294884] usbcore: registered new interface driver usb-storage
>>>>> [    1.301231] mousedev: PS/2 mouse device common for all mice
>>>>> [    1.307197] rtc-efi rtc-efi: rtc core: registered rtc-efi as rtc0
>>>>>
>>>>> But this error goes off, if I don't force ACPI booting, i.e., if I
>>>>> remove acpi=force from kernel command line , USB is detected  and my
>>>>> RFS which is in the usb drive, gets mounted successfully.
>>>>>
>>>
>>> As I mentioned in private, I do get the same error if I drop _CCA in
>>> USB object of ACPI DSDT. Can you give it a spin with latest UEFI ?
>>>
>>> Sure, will try with latest UEFI.
>>>
>>
>> I bet that's 8-12 months old. It puts the banner during boot with the
>> build date. You can try to follow [1] or access it from [2]
> 
> Agree.
> 
> D03 is using the same IP (EHCI) and the USB works fine with _CCA
> in the device node.

_CCA is mandatory on arm64 (see CONFIG_ACPI_CCA_REQUIRED). Any devices
without it are going to end up with the dummy DMA ops which
intentionally fail if a driver tries to use them - i.e. the error seen
above is by design.

Robin.

> 
> Thanks
> Hanjun
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel