linux-amlogic.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: jbrunet@baylibre.com (Jerome Brunet)
To: linus-amlogic@lists.infradead.org
Subject: [PATCH] clk: meson-gxbb: Add EE 32K Clock for CEC
Date: Mon, 29 May 2017 15:27:51 +0200	[thread overview]
Message-ID: <1496064471.2741.0.camel@baylibre.com> (raw)
In-Reply-To: <1495619025-1958-1-git-send-email-narmstrong@baylibre.com>

On Wed, 2017-05-24 at 11:43 +0200, Neil Armstrong wrote:
> On Amlogic GX SoCs, there is two CEC controllers :
> - An Amlogic CEC custom in the AO domain
> - The Synopsys HDMI-TX Controller in the EE domain
> 
> Each of these controllers needs a 32.768KHz clock, but there is two paths :
> - In the EE domain, the "32k_clk" this patchs is adding
> - In the AO domain, with a more complex dual divider more precise setup
> 
> The AO 32K clock support will be pushed later in the corresponding
> gxbb-aoclk driver when the AE CEC driver is ready.
> 
> The EE 32k_clk must be pushed earlier since mainline support for CEC in the
> Synopsys HDMI-TX controller is nearby.
> 
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

Rebased and applied.
Thx

Jerome

> ---
> ?drivers/clk/meson/gxbb.c | 54
> ++++++++++++++++++++++++++++++++++++++++++++++++
> ?drivers/clk/meson/gxbb.h |??5 ++++-
> ?2 files changed, 58 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/clk/meson/gxbb.c b/drivers/clk/meson/gxbb.c
> index ad5f027..4b7d85a 100644
> --- a/drivers/clk/meson/gxbb.c
> +++ b/drivers/clk/meson/gxbb.c
> @@ -951,6 +951,51 @@ struct pll_params_table gxl_gp0_params_table[] = {
> ?	},
> ?};
> ?
> +static struct clk_divider gxbb_32k_clk_div = {
> +	.reg = (void *)HHI_32K_CLK_CNTL,
> +	.shift = 0,
> +	.width = 14,
> +	.lock = &clk_lock,
> +	.hw.init = &(struct clk_init_data){
> +		.name = "32k_clk_div",
> +		.ops = &clk_divider_ops,
> +		.parent_names = (const char *[]){ "32k_clk_sel" },
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT | CLK_DIVIDER_ROUND_CLOSEST,
> +	},
> +};
> +
> +static struct clk_gate gxbb_32k_clk = {
> +	.reg = (void *)HHI_32K_CLK_CNTL,
> +	.bit_idx = 15,
> +	.lock = &clk_lock,
> +	.hw.init = &(struct clk_init_data){
> +		.name = "32k_clk",
> +		.ops = &clk_gate_ops,
> +		.parent_names = (const char *[]){ "32k_clk_div" },
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static const char *gxbb_32k_clk_parent_names[] = {
> +	"xtal", "cts_slow_oscin", "fclk_div3", "fclk_div5"
> +};
> +
> +static struct clk_mux gxbb_32k_clk_sel = {
> +	.reg = (void *)HHI_32K_CLK_CNTL,
> +	.mask = 0x3,
> +	.shift = 16,
> +	.lock = &clk_lock,
> +		.hw.init = &(struct clk_init_data){
> +		.name = "32k_clk_sel",
> +		.ops = &clk_mux_ops,
> +		.parent_names = gxbb_32k_clk_parent_names,
> +		.num_parents = 4,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> ?/* Everything Else (EE) domain gates */
> ?static MESON_GATE(gxbb_ddr, HHI_GCLK_MPEG0, 0);
> ?static MESON_GATE(gxbb_dos, HHI_GCLK_MPEG0, 1);
> @@ -1158,6 +1203,9 @@ struct pll_params_table gxl_gp0_params_table[] = {
> ?		[CLKID_CTS_MCLK_I958_SEL]???= &gxbb_cts_mclk_i958_sel.hw,
> ?		[CLKID_CTS_MCLK_I958_DIV]???= &gxbb_cts_mclk_i958_div.hw,
> ?		[CLKID_CTS_I958]	????= &gxbb_cts_i958.hw,
> +		[CLKID_32K_CLK]		????= &gxbb_32k_clk.hw,
> +		[CLKID_32K_CLK_SEL]	????= &gxbb_32k_clk_sel.hw,
> +		[CLKID_32K_CLK_DIV]	????= &gxbb_32k_clk_div.hw,
> ?	},
> ?	.num = NR_CLKS,
> ?};
> @@ -1278,6 +1326,9 @@ struct pll_params_table gxl_gp0_params_table[] = {
> ?		[CLKID_CTS_MCLK_I958_SEL]???= &gxbb_cts_mclk_i958_sel.hw,
> ?		[CLKID_CTS_MCLK_I958_DIV]???= &gxbb_cts_mclk_i958_div.hw,
> ?		[CLKID_CTS_I958]	????= &gxbb_cts_i958.hw,
> +		[CLKID_32K_CLK]		????= &gxbb_32k_clk.hw,
> +		[CLKID_32K_CLK_SEL]	????= &gxbb_32k_clk_sel.hw,
> +		[CLKID_32K_CLK_DIV]	????= &gxbb_32k_clk_div.hw,
> ?	},
> ?	.num = NR_CLKS,
> ?};
> @@ -1392,6 +1443,7 @@ struct pll_params_table gxl_gp0_params_table[] = {
> ?	&gxbb_mali_1,
> ?	&gxbb_cts_amclk,
> ?	&gxbb_cts_mclk_i958,
> +	&gxbb_32k_clk,
> ?};
> ?
> ?static struct clk_mux *const gxbb_clk_muxes[] = {
> @@ -1403,6 +1455,7 @@ struct pll_params_table gxl_gp0_params_table[] = {
> ?	&gxbb_cts_amclk_sel,
> ?	&gxbb_cts_mclk_i958_sel,
> ?	&gxbb_cts_i958,
> +	&gxbb_32k_clk_sel,
> ?};
> ?
> ?static struct clk_divider *const gxbb_clk_dividers[] = {
> @@ -1411,6 +1464,7 @@ struct pll_params_table gxl_gp0_params_table[] = {
> ?	&gxbb_mali_0_div,
> ?	&gxbb_mali_1_div,
> ?	&gxbb_cts_mclk_i958_div,
> +	&gxbb_32k_clk_div,
> ?};
> ?
> ?static struct meson_clk_audio_divider *const gxbb_audio_dividers[] = {
> diff --git a/drivers/clk/meson/gxbb.h b/drivers/clk/meson/gxbb.h
> index 93b8f07..de5fad0 100644
> --- a/drivers/clk/meson/gxbb.h
> +++ b/drivers/clk/meson/gxbb.h
> @@ -284,8 +284,11 @@
> ?#define CLKID_CTS_MCLK_I958_SEL	??111
> ?#define CLKID_CTS_MCLK_I958_DIV	??112
> ?#define CLKID_CTS_I958		??113
> +#define CLKID_32K_CLK		??114
> +#define CLKID_32K_CLK_SEL	??115
> +#define CLKID_32K_CLK_DIV	??116
> ?
> -#define NR_CLKS			??114
> +#define NR_CLKS			??117
> ?
> ?/* include the CLKIDs that have been made part of the stable DT binding */
> ?#include <dt-bindings/clock/gxbb-clkc.h>

      reply	other threads:[~2017-05-29 13:27 UTC|newest]

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-05-24  9:43 [PATCH] clk: meson-gxbb: Add EE 32K Clock for CEC Neil Armstrong
2017-05-29 13:27 ` Jerome Brunet [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1496064471.2741.0.camel@baylibre.com \
    --to=jbrunet@baylibre.com \
    --cc=linus-amlogic@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).