[PATCH 00/13] add support for more devices on Meson8 and Meson8b

[jbrunet@baylibre.com (Jerome Brunet)]

On Sun, 2017-06-11 at 12:16 +0200, Martin Blumenstingl wrote:
> This series adds:
> - USB support on Meson8 and Meson8b (it seems that some boards show an
> ? error when trying to initialize one of the USB2 PHYs, but we have the
> ? same problem on some GXBB boards. it is working fine for me - on a board
> ? which is not supported upstream yet)
> - hardware random number generator support (Meson8 and Meson8b seem to
> ? have two 32-bit hardware random number generator registers, while the
> ? GX SoCs only have one. This is not handled by the meson-rng driver yet,
> ? but that can still be improved later on)
> - SAR ADC support
> - add reserved memory zones to fix random hangs when filling the memory
> ? (currently only on Meson8 until I have a Meson8b device to test if the
> ? same problem appears there as well)
> - use the real ethernet clock on Meson8 and Meson8b to fix ethernet when
> ? the bootloader does not enable the gate clock
> - add the SCU (Snoop Control Unit) which is needed for SMP support
> - minor preparations for further .dts updates as this already exports the
> ? SDIO clocks (a driver for this MMC controller is work-in-progress) as
> ? well as the corresponding pin definitions in meson8.dtsi
> - this adds the pwm_e (typically used for the 32.768 kHz LPO clock for the
> ? SDIO wifi chip) and pwm_f (used on some boards for the dimmable power
> ? LED) pins to meson8.dtsi
> 
> NOTE: the .dts changes from this series depend on my previous patch from
> [0]: "ARM: dts: meson8: fix the IR receiver pins"
> 
> 
> [0] http://lists.infradead.org/pipermail/linux-amlogic/2017-June/003983.html
> 
> 
> Martin Blumenstingl (13):
> ? clk: meson8b: export the SAR ADC clocks
> ? clk: meson8b: export the SDIO clock
> ? clk: meson8b: export the gate clock for the HW random number generator
> ? clk: meson8b: export the USB clocks
> ? clk: meson8b: export the ethernet gate clock

Applied these 5 clk patches to next/headers with Neil's Acks.

> ? ARM: dts: meson8: add the PWM_E and PWM_F pins
> ? ARM: dts: meson8: add the pins for the SDIO controller
> ? ARM: dts: meson: add the SAR ADC
> ? ARM: dts: meson8: add reserved memory zones
> ? ARM: dts: meson: add the hardware random number generator
> ? ARM: dts: meson: add USB support on Meson8 and Meson8b
> ? ARM: dts: meson8b: add the SCU device node
> ? ARM: dts: meson: use the real ethernet clock on Meson8 and Meson8b
> 
> ?arch/arm/boot/dts/meson.dtsi?????????????|??51 +++++++++++++++
> ?arch/arm/boot/dts/meson8.dtsi????????????| 109
> ++++++++++++++++++++++++++++++-
> ?arch/arm/boot/dts/meson8b.dtsi???????????|??49 ++++++++++++++
> ?drivers/clk/meson/meson8b.h??????????????|??20 +++---
> ?include/dt-bindings/clock/meson8b-clkc.h |??10 +++
> ?5 files changed, 228 insertions(+), 11 deletions(-)
>