[PATCH 2/2] ARM64: dts: meson-gxbb-nanopi-k2: Add GPIO lines names

[narmstrong@baylibre.com (Neil Armstrong)]

This patch describes the GPIO lines usage on the Nanopi K2 board.

This is useful in the debugfs gpio file and using the cdev gpio API.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 .../boot/dts/amlogic/meson-gxbb-nanopi-k2.dts      | 58 ++++++++++++++++++++++
 1 file changed, 58 insertions(+)

diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
index fa46283..9697a7a 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
@@ -175,6 +175,64 @@
 	pinctrl-names = "default";
 };
 
+&pinctrl_aobus {
+	gpio-line-names = "UART TX", "UART RX", "Power Control", "Power Key In",
+			  "VCCK En", "CON1 Header Pin31",
+			  "I2S Header Pin6", "IR In", "I2S Header Pin7",
+			  "I2S Header Pin3", "I2S Header Pin4",
+			  "I2S Header Pin5", "HDMI CEC", "SYS LED";
+};
+
+&pinctrl_periphs {
+	gpio-line-names = /* Bank GPIOZ */
+			  "Eth MDIO", "Eth MDC", "Eth RGMII RX Clk",
+			  "Eth RX DV", "Eth RX D0", "Eth RX D1", "Eth RX D2",
+			  "Eth RX D3", "Eth RGMII TX Clk", "Eth TX En",
+			  "Eth TX D0", "Eth TX D1", "Eth TX D2", "Eth TX D3",
+			  "Eth PHY nRESET", "Eth PHY Intc",
+			  /* Bank GPIOH */
+			  "HDMI HPD", "HDMI DDC SDA", "HDMI DDC SCL",
+			  "CON1 Header Pin33",
+			  /* Bank BOOT */
+			  "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3", "eMMC D4",
+			  "eMMC D5", "eMMC D6", "eMMC D7", "eMMC Clk",
+			  "eMMC Reset", "eMMC CMD",
+			  "", "", "", "", "eMMC DS",
+			  "", "",
+			  /* Bank CARD */
+			  "SDCard D1", "SDCard D0", "SDCard CLK", "SDCard CMD",
+			  "SDCard D3", "SDCard D2", "SDCard Det",
+			  /* Bank GPIODV */
+			  "", "", "", "", "", "", "", "", "", "", "", "", "",
+			  "", "", "", "", "", "", "", "", "", "", "",
+			  "I2C A SDA", "I2C A SCK", "I2C B SDA", "I2C B SCK",
+			  "VDDEE Regulator", "VCCK Regulator",
+			  /* Bank GPIOY */
+			  "CON1 Header Pin7", "CON1 Header Pin11",
+			  "CON1 Header Pin13", "CON1 Header Pin15",
+			  "CON1 Header Pin18", "CON1 Header Pin19",
+			  "CON1 Header Pin22", "CON1 Header Pin21",
+			  "CON1 Header Pin24", "CON1 Header Pin23",
+			  "CON1 Header Pin26", "CON1 Header Pin29",
+			  "CON1 Header Pin32", "CON1 Header Pin8",
+			  "CON1 Header Pin10", "CON1 Header Pin16",
+			  "CON1 Header Pin12",
+			  /* Bank GPIOX */
+			  "WIFI SDIO D0", "WIFI SDIO D1", "WIFI SDIO D2",
+			  "WIFI SDIO D3", "WIFI SDIO CLK", "WIFI SDIO CMD",
+			  "WIFI Power Enable", "WIFI WAKE HOST",
+			  "Bluetooth PCM DOUT", "Bluetooth PCM DIN",
+			  "Bluetooth PCM SYNC", "Bluetooth PCM CLK",
+			  "Bluetooth UART TX", "Bluetooth UART RX",
+			  "Bluetooth UART CTS", "Bluetooth UART RTS",
+			  "", "", "", "WIFI 32K", "Bluetooth Enable",
+			  "Bluetooth WAKE HOST",
+			  /* Bank GPIOCLK */
+			  "", "CON1 Header Pin35", "", "",
+			  /* GPIO_TEST_N */
+			  "";
+};
+
 &pwm_ef {
 	status = "okay";
 	pinctrl-0 = <&pwm_e_pins>;
-- 
1.9.1