* [PATCH v6 0/2] Use onboard usb hub reset on Odroid N2
@ 2023-12-04 14:44 Anand Moon
2023-12-04 14:44 ` [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub Anand Moon
2023-12-04 14:44 ` [PATCH v6 2/2] arm64: dts: amlogic: Used onboard usb hub reset on odroid n2 Anand Moon
0 siblings, 2 replies; 23+ messages in thread
From: Anand Moon @ 2023-12-04 14:44 UTC (permalink / raw)
Cc: Anand Moon, Neil Armstrong, linux-amlogic
Add new binding for Genesys GL3523
Fix the dt_binding_check error
Fix commit message and peer-hub description
Fix commit message and vdd-supply description
Hope not more issue with these changes, finger crossed.
Previous:
v1: https://lore.kernel.org/r/20231010032446.3194-1-linux.amoon@gmail.com
v2: https://lore.kernel.org/all/169700589265.2911018.855796610271678067.robh@kernel.org/
v3: https://lore.kernel.org/all/20231119023454.1591-2-linux.amoon@gmail.com/
v4: https://lore.kernel.org/all/20231122182351.63214-2-linux.amoon@gmail.com/
v5: https://patchwork.kernel.org/project/linux-amlogic/patch/20231130053130.21966-2-linux.amoon@gmail.com/
Thanks
-Anand
Anand Moon (2):
dt-bindings: usb: Add the binding example for the Genesys Logic GL3523
hub
arm64: dts: amlogic: Used onboard usb hub reset on odroid n2
.../bindings/usb/genesys,gl850g.yaml | 65 +++++++++++++++++--
.../dts/amlogic/meson-g12b-odroid-n2.dtsi | 36 ++++++----
2 files changed, 85 insertions(+), 16 deletions(-)
--
2.42.0
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply [flat|nested] 23+ messages in thread* [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub 2023-12-04 14:44 [PATCH v6 0/2] Use onboard usb hub reset on Odroid N2 Anand Moon @ 2023-12-04 14:44 ` Anand Moon 2023-12-06 13:53 ` Rob Herring 2023-12-04 14:44 ` [PATCH v6 2/2] arm64: dts: amlogic: Used onboard usb hub reset on odroid n2 Anand Moon 1 sibling, 1 reply; 23+ messages in thread From: Anand Moon @ 2023-12-04 14:44 UTC (permalink / raw) To: Greg Kroah-Hartman, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Icenowy Zheng Cc: Anand Moon, Neil Armstrong, linux-amlogic, Conor Dooley, linux-usb, devicetree, linux-kernel Add the binding example for the USB3.1 Genesys Logic GL3523 integrates with USB 3.1 Gen 1 Super Speed and USB 2.0 High-Speed hub. For onboard hub controllers that support USB 3.x and USB 2.0 hubs with shared resets and power supplies, this property is used to identify the hubs with which these are shared. GL3523 has built-in 5V to 3.3V and 5V to 1.2V regulators, which serves power to the USB HUB, it uses 5V power regulator. Reviewed-by: Conor Dooley <conor.dooley@microchip.com> Signed-off-by: Anand Moon <linux.amoon@gmail.com> --- V6: fix the description of the regulators Updated the commit message for regulator updates. add reviewed by Conor Dooley [1] https://lore.kernel.org/all/20231130053130.21966-2-linux.amoon@gmail.com/ v5: upgrade peer-hub description : Conor Dooley [0] https://www.genesyslogic.com.tw/en/product_view.php?show=67 [Block Diagram] v4: Fix the description of peer-hub and update the commit message. Schematics of the Odroid N2+ https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.6_20210121.pdf V3: fix the dt_binding_check error, added new example for Genesys GL3523 v2: added Genesys GL3523 binding v1: none --- .../bindings/usb/genesys,gl850g.yaml | 65 +++++++++++++++++-- 1 file changed, 61 insertions(+), 4 deletions(-) diff --git a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml index ee08b9c3721f..c6f63a69396d 100644 --- a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml +++ b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml @@ -9,9 +9,6 @@ title: Genesys Logic USB hub controller maintainers: - Icenowy Zheng <uwu@icenowy.me> -allOf: - - $ref: usb-device.yaml# - properties: compatible: enum: @@ -27,12 +24,46 @@ properties: vdd-supply: description: - the regulator that provides 3.3V core power to the hub. + The regulator that provides 3.3V or 5.0V core power to the hub. + + peer-hub: + $ref: /schemas/types.yaml#/definitions/phandle + description: + For onboard hub controllers that support USB 3.x and USB 2.0 hubs + with shared resets and power supplies, this property is used to identify + the hubs with which these are shared. required: - compatible - reg +allOf: + - $ref: usb-device.yaml# + - if: + properties: + compatible: + contains: + enum: + - usb5e3,608 + then: + properties: + peer-hub: false + vdd-supply: false + reset-gpios: true + + - if: + properties: + compatible: + contains: + enum: + - usb5e3,610 + - usb5e3,620 + then: + properties: + peer-hub: true + vdd-supply: true + reset-gpios: true + additionalProperties: false examples: @@ -49,3 +80,29 @@ examples: reset-gpios = <&pio 7 2 GPIO_ACTIVE_LOW>; }; }; + + - | + #include <dt-bindings/gpio/gpio.h> + usb { + dr_mode = "host"; + #address-cells = <1>; + #size-cells = <0>; + + /* 2.0 hub on port 1 */ + hub_2_0: hub@1 { + compatible = "usb5e3,610"; + reg = <1>; + peer-hub = <&hub_3_0>; + reset-gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + vdd-supply = <&vcc_5v>; + }; + + /* 3.1 hub on port 4 */ + hub_3_0: hub@2 { + compatible = "usb5e3,620"; + reg = <2>; + peer-hub = <&hub_2_0>; + reset-gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + vdd-supply = <&vcc_5v>; + }; + }; -- 2.42.0 _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply related [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub 2023-12-04 14:44 ` [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub Anand Moon @ 2023-12-06 13:53 ` Rob Herring 2023-12-06 17:14 ` Anand Moon 0 siblings, 1 reply; 23+ messages in thread From: Rob Herring @ 2023-12-06 13:53 UTC (permalink / raw) To: Anand Moon Cc: Greg Kroah-Hartman, Krzysztof Kozlowski, Conor Dooley, Icenowy Zheng, Neil Armstrong, linux-amlogic, Conor Dooley, linux-usb, devicetree, linux-kernel On Mon, Dec 04, 2023 at 08:14:25PM +0530, Anand Moon wrote: > Add the binding example for the USB3.1 Genesys Logic GL3523 > integrates with USB 3.1 Gen 1 Super Speed and USB 2.0 High-Speed > hub. > > For onboard hub controllers that support USB 3.x and USB 2.0 hubs > with shared resets and power supplies, this property is used to identify > the hubs with which these are shared. > > GL3523 has built-in 5V to 3.3V and 5V to 1.2V regulators, which serves > power to the USB HUB, it uses 5V power regulator. > > Reviewed-by: Conor Dooley <conor.dooley@microchip.com> > Signed-off-by: Anand Moon <linux.amoon@gmail.com> > --- > V6: fix the description of the regulators > Updated the commit message for regulator updates. > add reviewed by Conor Dooley > [1] https://lore.kernel.org/all/20231130053130.21966-2-linux.amoon@gmail.com/ > v5: upgrade peer-hub description : Conor Dooley > [0] https://www.genesyslogic.com.tw/en/product_view.php?show=67 [Block Diagram] > v4: Fix the description of peer-hub and update the commit message. > Schematics of the Odroid N2+ > https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.6_20210121.pdf > V3: fix the dt_binding_check error, added new example for Genesys GL3523 > v2: added Genesys GL3523 binding > v1: none > --- > .../bindings/usb/genesys,gl850g.yaml | 65 +++++++++++++++++-- > 1 file changed, 61 insertions(+), 4 deletions(-) > > diff --git a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > index ee08b9c3721f..c6f63a69396d 100644 > --- a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > +++ b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > @@ -9,9 +9,6 @@ title: Genesys Logic USB hub controller > maintainers: > - Icenowy Zheng <uwu@icenowy.me> > > -allOf: > - - $ref: usb-device.yaml# > - > properties: > compatible: > enum: > @@ -27,12 +24,46 @@ properties: > > vdd-supply: > description: > - the regulator that provides 3.3V core power to the hub. > + The regulator that provides 3.3V or 5.0V core power to the hub. > + > + peer-hub: > + $ref: /schemas/types.yaml#/definitions/phandle > + description: > + For onboard hub controllers that support USB 3.x and USB 2.0 hubs > + with shared resets and power supplies, this property is used to identify > + the hubs with which these are shared. > > required: > - compatible > - reg > > +allOf: > + - $ref: usb-device.yaml# > + - if: > + properties: > + compatible: > + contains: > + enum: > + - usb5e3,608 > + then: > + properties: > + peer-hub: false > + vdd-supply: false > + reset-gpios: true > + > + - if: > + properties: > + compatible: > + contains: > + enum: > + - usb5e3,610 > + - usb5e3,620 > + then: > + properties: > + peer-hub: true > + vdd-supply: true > + reset-gpios: true No need for this if schema. The default is they are allowed. Rob _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub 2023-12-06 13:53 ` Rob Herring @ 2023-12-06 17:14 ` Anand Moon 2023-12-07 8:30 ` Krzysztof Kozlowski 0 siblings, 1 reply; 23+ messages in thread From: Anand Moon @ 2023-12-06 17:14 UTC (permalink / raw) To: Rob Herring Cc: Greg Kroah-Hartman, Krzysztof Kozlowski, Conor Dooley, Icenowy Zheng, Neil Armstrong, linux-amlogic, Conor Dooley, linux-usb, devicetree, linux-kernel Hi Rob, On Wed, 6 Dec 2023 at 19:23, Rob Herring <robh@kernel.org> wrote: > > On Mon, Dec 04, 2023 at 08:14:25PM +0530, Anand Moon wrote: > > Add the binding example for the USB3.1 Genesys Logic GL3523 > > integrates with USB 3.1 Gen 1 Super Speed and USB 2.0 High-Speed > > hub. > > > > For onboard hub controllers that support USB 3.x and USB 2.0 hubs > > with shared resets and power supplies, this property is used to identify > > the hubs with which these are shared. > > > > GL3523 has built-in 5V to 3.3V and 5V to 1.2V regulators, which serves > > power to the USB HUB, it uses 5V power regulator. > > > > Reviewed-by: Conor Dooley <conor.dooley@microchip.com> > > Signed-off-by: Anand Moon <linux.amoon@gmail.com> > > --- > > V6: fix the description of the regulators > > Updated the commit message for regulator updates. > > add reviewed by Conor Dooley > > [1] https://lore.kernel.org/all/20231130053130.21966-2-linux.amoon@gmail.com/ > > v5: upgrade peer-hub description : Conor Dooley > > [0] https://www.genesyslogic.com.tw/en/product_view.php?show=67 [Block Diagram] > > v4: Fix the description of peer-hub and update the commit message. > > Schematics of the Odroid N2+ > > https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.6_20210121.pdf > > V3: fix the dt_binding_check error, added new example for Genesys GL3523 > > v2: added Genesys GL3523 binding > > v1: none > > --- > > .../bindings/usb/genesys,gl850g.yaml | 65 +++++++++++++++++-- > > 1 file changed, 61 insertions(+), 4 deletions(-) > > > > diff --git a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > > index ee08b9c3721f..c6f63a69396d 100644 > > --- a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > > +++ b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > > @@ -9,9 +9,6 @@ title: Genesys Logic USB hub controller > > maintainers: > > - Icenowy Zheng <uwu@icenowy.me> > > > > -allOf: > > - - $ref: usb-device.yaml# > > - > > properties: > > compatible: > > enum: > > @@ -27,12 +24,46 @@ properties: > > > > vdd-supply: > > description: > > - the regulator that provides 3.3V core power to the hub. > > + The regulator that provides 3.3V or 5.0V core power to the hub. > > + > > + peer-hub: > > + $ref: /schemas/types.yaml#/definitions/phandle > > + description: > > + For onboard hub controllers that support USB 3.x and USB 2.0 hubs > > + with shared resets and power supplies, this property is used to identify > > + the hubs with which these are shared. > > > > required: > > - compatible > > - reg > > > > +allOf: > > + - $ref: usb-device.yaml# > > + - if: > > + properties: > > + compatible: > > + contains: > > + enum: > > + - usb5e3,608 > > + then: > > + properties: > > + peer-hub: false > > + vdd-supply: false > > + reset-gpios: true > > + > > + - if: > > + properties: > > + compatible: > > + contains: > > + enum: > > + - usb5e3,610 > > + - usb5e3,620 > > + then: > > + properties: > > + peer-hub: true > > + vdd-supply: true > > + reset-gpios: true > > No need for this if schema. The default is they are allowed. > If I move reset-gpios to required, I observe the below warning. DTC_CHK Documentation/devicetree/bindings/usb/maxim,max33359.example.dtb /home/alarm/linux-amlogic-5.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: hub@1: 'reset-gpio' is a required property from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# DTC_CHK Documentation/devicetree/bindings/usb/mediatek,musb.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/usb251xb.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/realtek,rts5411.example.dtb /home/alarm/linux-amlogic-5.y-devel/Documentation/devicetree/bindings/usb/genesys,gl850g.example.dtb: hub@1: 'reset-gpio' is a required property from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# DTC_CHK Documentation/devicetree/bindings/usb/brcm,bdc.example.dtb /home/alarm/linux-amlogic-5.y-devel/Documentation/devicetree/bindings/usb/genesys,gl850g.example.dtb: hub@1: 'reset-gpio' is a required property from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# DTC_CHK Documentation/devicetree/bindings/usb/xlnx,usb2.example.dtb /home/alarm/linux-amlogic-5.y-devel/Documentation/devicetree/bindings/usb/genesys,gl850g.example.dtb: hub@2: 'reset-gpio' is a required property from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# DTC_CHK Documentation/devicetree/bindings/usb/starfive,jh7110-usb.example.dtb > Rob Thanks -Anand _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub 2023-12-06 17:14 ` Anand Moon @ 2023-12-07 8:30 ` Krzysztof Kozlowski 2023-12-07 12:33 ` Anand Moon 0 siblings, 1 reply; 23+ messages in thread From: Krzysztof Kozlowski @ 2023-12-07 8:30 UTC (permalink / raw) To: Anand Moon, Rob Herring Cc: Greg Kroah-Hartman, Krzysztof Kozlowski, Conor Dooley, Icenowy Zheng, Neil Armstrong, linux-amlogic, Conor Dooley, linux-usb, devicetree, linux-kernel On 06/12/2023 18:14, Anand Moon wrote: > Hi Rob, > > On Wed, 6 Dec 2023 at 19:23, Rob Herring <robh@kernel.org> wrote: >> >> On Mon, Dec 04, 2023 at 08:14:25PM +0530, Anand Moon wrote: >>> Add the binding example for the USB3.1 Genesys Logic GL3523 >>> integrates with USB 3.1 Gen 1 Super Speed and USB 2.0 High-Speed >>> hub. >>> >>> For onboard hub controllers that support USB 3.x and USB 2.0 hubs >>> with shared resets and power supplies, this property is used to identify >>> the hubs with which these are shared. >>> >>> GL3523 has built-in 5V to 3.3V and 5V to 1.2V regulators, which serves >>> power to the USB HUB, it uses 5V power regulator. >>> >>> Reviewed-by: Conor Dooley <conor.dooley@microchip.com> >>> Signed-off-by: Anand Moon <linux.amoon@gmail.com> >>> --- >>> V6: fix the description of the regulators >>> Updated the commit message for regulator updates. >>> add reviewed by Conor Dooley >>> [1] https://lore.kernel.org/all/20231130053130.21966-2-linux.amoon@gmail.com/ >>> v5: upgrade peer-hub description : Conor Dooley >>> [0] https://www.genesyslogic.com.tw/en/product_view.php?show=67 [Block Diagram] >>> v4: Fix the description of peer-hub and update the commit message. >>> Schematics of the Odroid N2+ >>> https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.6_20210121.pdf >>> V3: fix the dt_binding_check error, added new example for Genesys GL3523 >>> v2: added Genesys GL3523 binding >>> v1: none >>> --- >>> .../bindings/usb/genesys,gl850g.yaml | 65 +++++++++++++++++-- >>> 1 file changed, 61 insertions(+), 4 deletions(-) >>> >>> diff --git a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml >>> index ee08b9c3721f..c6f63a69396d 100644 >>> --- a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml >>> +++ b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml >>> @@ -9,9 +9,6 @@ title: Genesys Logic USB hub controller >>> maintainers: >>> - Icenowy Zheng <uwu@icenowy.me> >>> >>> -allOf: >>> - - $ref: usb-device.yaml# >>> - >>> properties: >>> compatible: >>> enum: >>> @@ -27,12 +24,46 @@ properties: >>> >>> vdd-supply: >>> description: >>> - the regulator that provides 3.3V core power to the hub. >>> + The regulator that provides 3.3V or 5.0V core power to the hub. >>> + >>> + peer-hub: >>> + $ref: /schemas/types.yaml#/definitions/phandle >>> + description: >>> + For onboard hub controllers that support USB 3.x and USB 2.0 hubs >>> + with shared resets and power supplies, this property is used to identify >>> + the hubs with which these are shared. >>> >>> required: >>> - compatible >>> - reg >>> >>> +allOf: >>> + - $ref: usb-device.yaml# >>> + - if: >>> + properties: >>> + compatible: >>> + contains: >>> + enum: >>> + - usb5e3,608 >>> + then: >>> + properties: >>> + peer-hub: false >>> + vdd-supply: false >>> + reset-gpios: true >>> + >>> + - if: >>> + properties: >>> + compatible: >>> + contains: >>> + enum: >>> + - usb5e3,610 >>> + - usb5e3,620 >>> + then: >>> + properties: >>> + peer-hub: true >>> + vdd-supply: true >>> + reset-gpios: true >> >> No need for this if schema. The default is they are allowed. >> > > If I move reset-gpios to required, I observe the below warning. > > DTC_CHK Documentation/devicetree/bindings/usb/maxim,max33359.example.dtb > /home/alarm/linux-amlogic-5.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: > hub@1: 'reset-gpio' is a required property > from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# Where are the properties defined? If you open the binding you see: nowhere. You cannot define properties in some variant with "true". Please define all of them in top-level and only narrow/constrain when applicable. Best regards, Krzysztof _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub 2023-12-07 8:30 ` Krzysztof Kozlowski @ 2023-12-07 12:33 ` Anand Moon 2023-12-07 12:40 ` Krzysztof Kozlowski 0 siblings, 1 reply; 23+ messages in thread From: Anand Moon @ 2023-12-07 12:33 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Rob Herring, Greg Kroah-Hartman, Krzysztof Kozlowski, Conor Dooley, Icenowy Zheng, Neil Armstrong, linux-amlogic, Conor Dooley, linux-usb, devicetree, linux-kernel Hi Krzysztof On Thu, 7 Dec 2023 at 14:00, Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote: > > On 06/12/2023 18:14, Anand Moon wrote: > > Hi Rob, > > > > On Wed, 6 Dec 2023 at 19:23, Rob Herring <robh@kernel.org> wrote: > >> > >> On Mon, Dec 04, 2023 at 08:14:25PM +0530, Anand Moon wrote: > >>> Add the binding example for the USB3.1 Genesys Logic GL3523 > >>> integrates with USB 3.1 Gen 1 Super Speed and USB 2.0 High-Speed > >>> hub. > >>> > >>> For onboard hub controllers that support USB 3.x and USB 2.0 hubs > >>> with shared resets and power supplies, this property is used to identify > >>> the hubs with which these are shared. > >>> > >>> GL3523 has built-in 5V to 3.3V and 5V to 1.2V regulators, which serves > >>> power to the USB HUB, it uses 5V power regulator. > >>> > >>> Reviewed-by: Conor Dooley <conor.dooley@microchip.com> > >>> Signed-off-by: Anand Moon <linux.amoon@gmail.com> > >>> --- > >>> V6: fix the description of the regulators > >>> Updated the commit message for regulator updates. > >>> add reviewed by Conor Dooley > >>> [1] https://lore.kernel.org/all/20231130053130.21966-2-linux.amoon@gmail.com/ > >>> v5: upgrade peer-hub description : Conor Dooley > >>> [0] https://www.genesyslogic.com.tw/en/product_view.php?show=67 [Block Diagram] > >>> v4: Fix the description of peer-hub and update the commit message. > >>> Schematics of the Odroid N2+ > >>> https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.6_20210121.pdf > >>> V3: fix the dt_binding_check error, added new example for Genesys GL3523 > >>> v2: added Genesys GL3523 binding > >>> v1: none > >>> --- > >>> .../bindings/usb/genesys,gl850g.yaml | 65 +++++++++++++++++-- > >>> 1 file changed, 61 insertions(+), 4 deletions(-) > >>> > >>> diff --git a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > >>> index ee08b9c3721f..c6f63a69396d 100644 > >>> --- a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > >>> +++ b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > >>> @@ -9,9 +9,6 @@ title: Genesys Logic USB hub controller > >>> maintainers: > >>> - Icenowy Zheng <uwu@icenowy.me> > >>> > >>> -allOf: > >>> - - $ref: usb-device.yaml# > >>> - > >>> properties: > >>> compatible: > >>> enum: > >>> @@ -27,12 +24,46 @@ properties: > >>> > >>> vdd-supply: > >>> description: > >>> - the regulator that provides 3.3V core power to the hub. > >>> + The regulator that provides 3.3V or 5.0V core power to the hub. > >>> + > >>> + peer-hub: > >>> + $ref: /schemas/types.yaml#/definitions/phandle > >>> + description: > >>> + For onboard hub controllers that support USB 3.x and USB 2.0 hubs > >>> + with shared resets and power supplies, this property is used to identify > >>> + the hubs with which these are shared. > >>> > >>> required: > >>> - compatible > >>> - reg > >>> > >>> +allOf: > >>> + - $ref: usb-device.yaml# > >>> + - if: > >>> + properties: > >>> + compatible: > >>> + contains: > >>> + enum: > >>> + - usb5e3,608 > >>> + then: > >>> + properties: > >>> + peer-hub: false > >>> + vdd-supply: false > >>> + reset-gpios: true > >>> + > >>> + - if: > >>> + properties: > >>> + compatible: > >>> + contains: > >>> + enum: > >>> + - usb5e3,610 > >>> + - usb5e3,620 > >>> + then: > >>> + properties: > >>> + peer-hub: true > >>> + vdd-supply: true > >>> + reset-gpios: true > >> > >> No need for this if schema. The default is they are allowed. > >> > > > > If I move reset-gpios to required, I observe the below warning. > > > > DTC_CHK Documentation/devicetree/bindings/usb/maxim,max33359.example.dtb > > /home/alarm/linux-amlogic-5.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: > > hub@1: 'reset-gpio' is a required property > > from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# > > Where are the properties defined? If you open the binding you see: > nowhere. You cannot define properties in some variant with "true". > Please define all of them in top-level and only narrow/constrain when > applicable. > What I meant is the example below, required meant applicable for both the binding But it shows me the above warning. required: - compatible - reg - reset-gpio allOf: - $ref: usb-device.yaml# - if: properties: compatible: contains: enum: - usb5e3,608 then: properties: peer-hub: false vdd-supply: false - if: properties: compatible: contains: enum: - usb5e3,610 - usb5e3,620 then: properties: peer-hub: true vdd-supply: true additionalProperties: false > > Best regards, > Krzysztof > Thanks -Anand _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub 2023-12-07 12:33 ` Anand Moon @ 2023-12-07 12:40 ` Krzysztof Kozlowski 2023-12-08 0:24 ` Anand Moon 0 siblings, 1 reply; 23+ messages in thread From: Krzysztof Kozlowski @ 2023-12-07 12:40 UTC (permalink / raw) To: Anand Moon Cc: Rob Herring, Greg Kroah-Hartman, Krzysztof Kozlowski, Conor Dooley, Icenowy Zheng, Neil Armstrong, linux-amlogic, Conor Dooley, linux-usb, devicetree, linux-kernel On 07/12/2023 13:33, Anand Moon wrote: > Hi Krzysztof > > On Thu, 7 Dec 2023 at 14:00, Krzysztof Kozlowski > <krzysztof.kozlowski@linaro.org> wrote: >> >> On 06/12/2023 18:14, Anand Moon wrote: >>> Hi Rob, >>> >>> On Wed, 6 Dec 2023 at 19:23, Rob Herring <robh@kernel.org> wrote: >>>> >>>> On Mon, Dec 04, 2023 at 08:14:25PM +0530, Anand Moon wrote: >>>>> Add the binding example for the USB3.1 Genesys Logic GL3523 >>>>> integrates with USB 3.1 Gen 1 Super Speed and USB 2.0 High-Speed >>>>> hub. >>>>> >>>>> For onboard hub controllers that support USB 3.x and USB 2.0 hubs >>>>> with shared resets and power supplies, this property is used to identify >>>>> the hubs with which these are shared. >>>>> >>>>> GL3523 has built-in 5V to 3.3V and 5V to 1.2V regulators, which serves >>>>> power to the USB HUB, it uses 5V power regulator. >>>>> >>>>> Reviewed-by: Conor Dooley <conor.dooley@microchip.com> >>>>> Signed-off-by: Anand Moon <linux.amoon@gmail.com> >>>>> --- >>>>> V6: fix the description of the regulators >>>>> Updated the commit message for regulator updates. >>>>> add reviewed by Conor Dooley >>>>> [1] https://lore.kernel.org/all/20231130053130.21966-2-linux.amoon@gmail.com/ >>>>> v5: upgrade peer-hub description : Conor Dooley >>>>> [0] https://www.genesyslogic.com.tw/en/product_view.php?show=67 [Block Diagram] >>>>> v4: Fix the description of peer-hub and update the commit message. >>>>> Schematics of the Odroid N2+ >>>>> https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.6_20210121.pdf >>>>> V3: fix the dt_binding_check error, added new example for Genesys GL3523 >>>>> v2: added Genesys GL3523 binding >>>>> v1: none >>>>> --- >>>>> .../bindings/usb/genesys,gl850g.yaml | 65 +++++++++++++++++-- >>>>> 1 file changed, 61 insertions(+), 4 deletions(-) >>>>> >>>>> diff --git a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml >>>>> index ee08b9c3721f..c6f63a69396d 100644 >>>>> --- a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml >>>>> +++ b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml >>>>> @@ -9,9 +9,6 @@ title: Genesys Logic USB hub controller >>>>> maintainers: >>>>> - Icenowy Zheng <uwu@icenowy.me> >>>>> >>>>> -allOf: >>>>> - - $ref: usb-device.yaml# >>>>> - >>>>> properties: >>>>> compatible: >>>>> enum: >>>>> @@ -27,12 +24,46 @@ properties: >>>>> >>>>> vdd-supply: >>>>> description: >>>>> - the regulator that provides 3.3V core power to the hub. >>>>> + The regulator that provides 3.3V or 5.0V core power to the hub. >>>>> + >>>>> + peer-hub: >>>>> + $ref: /schemas/types.yaml#/definitions/phandle >>>>> + description: >>>>> + For onboard hub controllers that support USB 3.x and USB 2.0 hubs >>>>> + with shared resets and power supplies, this property is used to identify >>>>> + the hubs with which these are shared. >>>>> >>>>> required: >>>>> - compatible >>>>> - reg >>>>> >>>>> +allOf: >>>>> + - $ref: usb-device.yaml# >>>>> + - if: >>>>> + properties: >>>>> + compatible: >>>>> + contains: >>>>> + enum: >>>>> + - usb5e3,608 >>>>> + then: >>>>> + properties: >>>>> + peer-hub: false >>>>> + vdd-supply: false >>>>> + reset-gpios: true >>>>> + >>>>> + - if: >>>>> + properties: >>>>> + compatible: >>>>> + contains: >>>>> + enum: >>>>> + - usb5e3,610 >>>>> + - usb5e3,620 >>>>> + then: >>>>> + properties: >>>>> + peer-hub: true >>>>> + vdd-supply: true >>>>> + reset-gpios: true >>>> >>>> No need for this if schema. The default is they are allowed. >>>> >>> >>> If I move reset-gpios to required, I observe the below warning. >>> >>> DTC_CHK Documentation/devicetree/bindings/usb/maxim,max33359.example.dtb >>> /home/alarm/linux-amlogic-5.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: >>> hub@1: 'reset-gpio' is a required property >>> from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# >> >> Where are the properties defined? If you open the binding you see: >> nowhere. You cannot define properties in some variant with "true". >> Please define all of them in top-level and only narrow/constrain when >> applicable. >> > What I meant is the example below, required meant applicable for both > the binding > But it shows me the above warning. My explanation stands... So again: >> Please define all of them in top-level and only narrow/constrain when >> applicable. Best regards, Krzysztof _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub 2023-12-07 12:40 ` Krzysztof Kozlowski @ 2023-12-08 0:24 ` Anand Moon 2023-12-08 7:44 ` Krzysztof Kozlowski 0 siblings, 1 reply; 23+ messages in thread From: Anand Moon @ 2023-12-08 0:24 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Rob Herring, Greg Kroah-Hartman, Krzysztof Kozlowski, Conor Dooley, Icenowy Zheng, Neil Armstrong, linux-amlogic, Conor Dooley, linux-usb, devicetree, linux-kernel Hi Krzysztof, On Thu, 7 Dec 2023 at 18:11, Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote: > > On 07/12/2023 13:33, Anand Moon wrote: > > Hi Krzysztof > > > > On Thu, 7 Dec 2023 at 14:00, Krzysztof Kozlowski > > <krzysztof.kozlowski@linaro.org> wrote: > >> > >> On 06/12/2023 18:14, Anand Moon wrote: > >>> Hi Rob, > >>> > >>> On Wed, 6 Dec 2023 at 19:23, Rob Herring <robh@kernel.org> wrote: > >>>> > >>>> On Mon, Dec 04, 2023 at 08:14:25PM +0530, Anand Moon wrote: > >>>>> Add the binding example for the USB3.1 Genesys Logic GL3523 > >>>>> integrates with USB 3.1 Gen 1 Super Speed and USB 2.0 High-Speed > >>>>> hub. > >>>>> > >>>>> For onboard hub controllers that support USB 3.x and USB 2.0 hubs > >>>>> with shared resets and power supplies, this property is used to identify > >>>>> the hubs with which these are shared. > >>>>> > >>>>> GL3523 has built-in 5V to 3.3V and 5V to 1.2V regulators, which serves > >>>>> power to the USB HUB, it uses 5V power regulator. > >>>>> > >>>>> Reviewed-by: Conor Dooley <conor.dooley@microchip.com> > >>>>> Signed-off-by: Anand Moon <linux.amoon@gmail.com> > >>>>> --- > >>>>> V6: fix the description of the regulators > >>>>> Updated the commit message for regulator updates. > >>>>> add reviewed by Conor Dooley > >>>>> [1] https://lore.kernel.org/all/20231130053130.21966-2-linux.amoon@gmail.com/ > >>>>> v5: upgrade peer-hub description : Conor Dooley > >>>>> [0] https://www.genesyslogic.com.tw/en/product_view.php?show=67 [Block Diagram] > >>>>> v4: Fix the description of peer-hub and update the commit message. > >>>>> Schematics of the Odroid N2+ > >>>>> https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.6_20210121.pdf > >>>>> V3: fix the dt_binding_check error, added new example for Genesys GL3523 > >>>>> v2: added Genesys GL3523 binding > >>>>> v1: none > >>>>> --- > >>>>> .../bindings/usb/genesys,gl850g.yaml | 65 +++++++++++++++++-- > >>>>> 1 file changed, 61 insertions(+), 4 deletions(-) > >>>>> > >>>>> diff --git a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > >>>>> index ee08b9c3721f..c6f63a69396d 100644 > >>>>> --- a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > >>>>> +++ b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > >>>>> @@ -9,9 +9,6 @@ title: Genesys Logic USB hub controller > >>>>> maintainers: > >>>>> - Icenowy Zheng <uwu@icenowy.me> > >>>>> > >>>>> -allOf: > >>>>> - - $ref: usb-device.yaml# > >>>>> - > >>>>> properties: > >>>>> compatible: > >>>>> enum: > >>>>> @@ -27,12 +24,46 @@ properties: > >>>>> > >>>>> vdd-supply: > >>>>> description: > >>>>> - the regulator that provides 3.3V core power to the hub. > >>>>> + The regulator that provides 3.3V or 5.0V core power to the hub. > >>>>> + > >>>>> + peer-hub: > >>>>> + $ref: /schemas/types.yaml#/definitions/phandle > >>>>> + description: > >>>>> + For onboard hub controllers that support USB 3.x and USB 2.0 hubs > >>>>> + with shared resets and power supplies, this property is used to identify > >>>>> + the hubs with which these are shared. > >>>>> > >>>>> required: > >>>>> - compatible > >>>>> - reg > >>>>> > >>>>> +allOf: > >>>>> + - $ref: usb-device.yaml# > >>>>> + - if: > >>>>> + properties: > >>>>> + compatible: > >>>>> + contains: > >>>>> + enum: > >>>>> + - usb5e3,608 > >>>>> + then: > >>>>> + properties: > >>>>> + peer-hub: false > >>>>> + vdd-supply: false > >>>>> + reset-gpios: true > >>>>> + > >>>>> + - if: > >>>>> + properties: > >>>>> + compatible: > >>>>> + contains: > >>>>> + enum: > >>>>> + - usb5e3,610 > >>>>> + - usb5e3,620 > >>>>> + then: > >>>>> + properties: > >>>>> + peer-hub: true > >>>>> + vdd-supply: true > >>>>> + reset-gpios: true > >>>> > >>>> No need for this if schema. The default is they are allowed. > >>>> > >>> > >>> If I move reset-gpios to required, I observe the below warning. > >>> > >>> DTC_CHK Documentation/devicetree/bindings/usb/maxim,max33359.example.dtb > >>> /home/alarm/linux-amlogic-5.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: > >>> hub@1: 'reset-gpio' is a required property > >>> from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# > >> > >> Where are the properties defined? If you open the binding you see: > >> nowhere. You cannot define properties in some variant with "true". > >> Please define all of them in top-level and only narrow/constrain when > >> applicable. > >> > > What I meant is the example below, required meant applicable for both > > the binding > > But it shows me the above warning. > > My explanation stands... So again: > > >> Please define all of them in top-level and only narrow/constrain when > >> applicable. > Apologies, But I have tried this multiple times but have not been able to fix the device tree warning I have verified that example Documentation/devicetree/bindings/usb/genesys,gl850g.example.dts generate is correct required: - compatible - reg - reset-gpio - peer-hub - vdd-supply allOf: - $ref: usb-device.yaml# - if: properties: compatible: contains: enum: - usb5e3,608 then: properties: peer-hub: false vdd-supply: false - if: properties: compatible: contains: enum: - usb5e3,610 - usb5e3,620 then: properties: peer-hub: true vdd-supply: true additionalProperties: false > Best regards, > Krzysztof > Thanks -Anand _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub 2023-12-08 0:24 ` Anand Moon @ 2023-12-08 7:44 ` Krzysztof Kozlowski 2023-12-08 11:19 ` Anand Moon 0 siblings, 1 reply; 23+ messages in thread From: Krzysztof Kozlowski @ 2023-12-08 7:44 UTC (permalink / raw) To: Anand Moon Cc: Rob Herring, Greg Kroah-Hartman, Krzysztof Kozlowski, Conor Dooley, Icenowy Zheng, Neil Armstrong, linux-amlogic, Conor Dooley, linux-usb, devicetree, linux-kernel On 08/12/2023 01:24, Anand Moon wrote: >>>>> >>>>> If I move reset-gpios to required, I observe the below warning. >>>>> >>>>> DTC_CHK Documentation/devicetree/bindings/usb/maxim,max33359.example.dtb >>>>> /home/alarm/linux-amlogic-5.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: >>>>> hub@1: 'reset-gpio' is a required property >>>>> from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# >>>> >>>> Where are the properties defined? If you open the binding you see: >>>> nowhere. You cannot define properties in some variant with "true". >>>> Please define all of them in top-level and only narrow/constrain when >>>> applicable. >>>> >>> What I meant is the example below, required meant applicable for both >>> the binding >>> But it shows me the above warning. >> >> My explanation stands... So again: >> >>>> Please define all of them in top-level and only narrow/constrain when >>>> applicable. >> > Apologies, But I have tried this multiple times but have not been able > to fix the device tree warning Did you document all properties in top-level "properties:" block? Best regards, Krzysztof _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub 2023-12-08 7:44 ` Krzysztof Kozlowski @ 2023-12-08 11:19 ` Anand Moon 2023-12-08 12:17 ` Krzysztof Kozlowski 0 siblings, 1 reply; 23+ messages in thread From: Anand Moon @ 2023-12-08 11:19 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Rob Herring, Greg Kroah-Hartman, Krzysztof Kozlowski, Conor Dooley, Icenowy Zheng, Neil Armstrong, linux-amlogic, Conor Dooley, linux-usb, devicetree, linux-kernel Hi Krzysztof, On Fri, 8 Dec 2023 at 13:14, Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote: > > On 08/12/2023 01:24, Anand Moon wrote: > >>>>> > >>>>> If I move reset-gpios to required, I observe the below warning. > >>>>> > >>>>> DTC_CHK Documentation/devicetree/bindings/usb/maxim,max33359.example.dtb > >>>>> /home/alarm/linux-amlogic-5.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: > >>>>> hub@1: 'reset-gpio' is a required property > >>>>> from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# > >>>> > >>>> Where are the properties defined? If you open the binding you see: > >>>> nowhere. You cannot define properties in some variant with "true". > >>>> Please define all of them in top-level and only narrow/constrain when > >>>> applicable. > >>>> > >>> What I meant is the example below, required meant applicable for both > >>> the binding > >>> But it shows me the above warning. > >> > >> My explanation stands... So again: > >> > >>>> Please define all of them in top-level and only narrow/constrain when > >>>> applicable. > >> > > Apologies, But I have tried this multiple times but have not been able > > to fix the device tree warning > > Did you document all properties in top-level "properties:" block? > Yes, I have, Can you suggest a couple of examples to follow? I looked at some of the YAML files but could not fix my issue. Thanks -Anand _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub 2023-12-08 11:19 ` Anand Moon @ 2023-12-08 12:17 ` Krzysztof Kozlowski 2023-12-12 6:22 ` Anand Moon 0 siblings, 1 reply; 23+ messages in thread From: Krzysztof Kozlowski @ 2023-12-08 12:17 UTC (permalink / raw) To: Anand Moon Cc: Rob Herring, Greg Kroah-Hartman, Krzysztof Kozlowski, Conor Dooley, Icenowy Zheng, Neil Armstrong, linux-amlogic, Conor Dooley, linux-usb, devicetree, linux-kernel On 08/12/2023 12:19, Anand Moon wrote: > Hi Krzysztof, > > On Fri, 8 Dec 2023 at 13:14, Krzysztof Kozlowski > <krzysztof.kozlowski@linaro.org> wrote: >> >> On 08/12/2023 01:24, Anand Moon wrote: >>>>>>> >>>>>>> If I move reset-gpios to required, I observe the below warning. >>>>>>> >>>>>>> DTC_CHK Documentation/devicetree/bindings/usb/maxim,max33359.example.dtb >>>>>>> /home/alarm/linux-amlogic-5.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: >>>>>>> hub@1: 'reset-gpio' is a required property >>>>>>> from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# >>>>>> >>>>>> Where are the properties defined? If you open the binding you see: >>>>>> nowhere. You cannot define properties in some variant with "true". >>>>>> Please define all of them in top-level and only narrow/constrain when >>>>>> applicable. >>>>>> >>>>> What I meant is the example below, required meant applicable for both >>>>> the binding >>>>> But it shows me the above warning. >>>> >>>> My explanation stands... So again: >>>> >>>>>> Please define all of them in top-level and only narrow/constrain when >>>>>> applicable. >>>> >>> Apologies, But I have tried this multiple times but have not been able >>> to fix the device tree warning >> >> Did you document all properties in top-level "properties:" block? >> > Yes, I have, > > Can you suggest a couple of examples to follow? > I looked at some of the YAML files but could not fix my issue. 99% of bindings. Look also at example-schema. You can also attach here complete patch for fast look / short review. Best regards, Krzysztof _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub 2023-12-08 12:17 ` Krzysztof Kozlowski @ 2023-12-12 6:22 ` Anand Moon 2023-12-12 8:40 ` Krzysztof Kozlowski 0 siblings, 1 reply; 23+ messages in thread From: Anand Moon @ 2023-12-12 6:22 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Rob Herring, Greg Kroah-Hartman, Krzysztof Kozlowski, Conor Dooley, Icenowy Zheng, Neil Armstrong, linux-amlogic, Conor Dooley, linux-usb, devicetree, linux-kernel Hi Krzysztof, On Fri, 8 Dec 2023 at 17:47, Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote: > > On 08/12/2023 12:19, Anand Moon wrote: > > Hi Krzysztof, > > > > On Fri, 8 Dec 2023 at 13:14, Krzysztof Kozlowski > > <krzysztof.kozlowski@linaro.org> wrote: > >> > >> On 08/12/2023 01:24, Anand Moon wrote: > >>>>>>> > >>>>>>> If I move reset-gpios to required, I observe the below warning. > >>>>>>> > >>>>>>> DTC_CHK Documentation/devicetree/bindings/usb/maxim,max33359.example.dtb > >>>>>>> /home/alarm/linux-amlogic-5.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: > >>>>>>> hub@1: 'reset-gpio' is a required property > >>>>>>> from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# > >>>>>> > >>>>>> Where are the properties defined? If you open the binding you see: > >>>>>> nowhere. You cannot define properties in some variant with "true". > >>>>>> Please define all of them in top-level and only narrow/constrain when > >>>>>> applicable. > >>>>>> > >>>>> What I meant is the example below, required meant applicable for both > >>>>> the binding > >>>>> But it shows me the above warning. > >>>> > >>>> My explanation stands... So again: > >>>> > >>>>>> Please define all of them in top-level and only narrow/constrain when > >>>>>> applicable. > >>>> > >>> Apologies, But I have tried this multiple times but have not been able > >>> to fix the device tree warning > >> > >> Did you document all properties in top-level "properties:" block? > >> > > Yes, I have, > > > > Can you suggest a couple of examples to follow? > > I looked at some of the YAML files but could not fix my issue. > > 99% of bindings. Look also at example-schema. > > You can also attach here complete patch for fast look / short review. > Please find the modified patch, I have tried a few things but none resolve the binding warning. I am not able to debug this. -Thanks Anand -----8<----------8<----------8<----------8<----------8<----------8<----- diff --git a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml index ee08b9c3721f..7f75fa3c1945 100644 --- a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml +++ b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml @@ -9,9 +9,6 @@ title: Genesys Logic USB hub controller maintainers: - Icenowy Zheng <uwu@icenowy.me> -allOf: - - $ref: usb-device.yaml# - properties: compatible: enum: @@ -27,11 +24,47 @@ properties: vdd-supply: description: - the regulator that provides 3.3V core power to the hub. + The regulator that provides 3.3V or 5.0V core power to the hub. + + peer-hub: + $ref: /schemas/types.yaml#/definitions/phandle + description: + For onboard hub controllers that support USB 3.x and USB 2.0 hubs with + shared resets and power supplies, this property is used to identify the + hubs with which these are shared. required: - compatible - reg + - vdd-supply + - reset-gpios + - peer-hub + +allOf: + - $ref: usb-device.yaml# + + - if: + properties: + compatible: + contains: + enum: + - usb5e3,608 + then: + properties: + peer-hub: false + vdd-supply: false + + - if: + properties: + compatible: + contains: + enum: + - usb5e3,610 + - usb5e3,620 + then: + properties: + peer-hub: true + vdd-supply: true additionalProperties: false @@ -49,3 +82,29 @@ examples: reset-gpios = <&pio 7 2 GPIO_ACTIVE_LOW>; }; }; + + - | + #include <dt-bindings/gpio/gpio.h> + usb { + dr_mode = "host"; + #address-cells = <1>; + #size-cells = <0>; + + /* 2.0 hub on port 1 */ + hub_2_0: hub@1 { + compatible = "usb5e3,610"; + reg = <1>; + peer-hub = <&hub_3_0>; + reset-gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + vdd-supply = <&vcc_5v>; + }; + + /* 3.1 hub on port 4 */ + hub_3_0: hub@2 { + compatible = "usb5e3,620"; + reg = <2>; + peer-hub = <&hub_2_0>; + reset-gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + vdd-supply = <&vcc_5v>; + }; + }; _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply related [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub 2023-12-12 6:22 ` Anand Moon @ 2023-12-12 8:40 ` Krzysztof Kozlowski 2023-12-12 11:37 ` Anand Moon 0 siblings, 1 reply; 23+ messages in thread From: Krzysztof Kozlowski @ 2023-12-12 8:40 UTC (permalink / raw) To: Anand Moon Cc: Rob Herring, Greg Kroah-Hartman, Krzysztof Kozlowski, Conor Dooley, Icenowy Zheng, Neil Armstrong, linux-amlogic, Conor Dooley, linux-usb, devicetree, linux-kernel On 12/12/2023 07:22, Anand Moon wrote: > Hi Krzysztof, > > On Fri, 8 Dec 2023 at 17:47, Krzysztof Kozlowski > <krzysztof.kozlowski@linaro.org> wrote: >> >> On 08/12/2023 12:19, Anand Moon wrote: >>> Hi Krzysztof, >>> >>> On Fri, 8 Dec 2023 at 13:14, Krzysztof Kozlowski >>> <krzysztof.kozlowski@linaro.org> wrote: >>>> >>>> On 08/12/2023 01:24, Anand Moon wrote: >>>>>>>>> >>>>>>>>> If I move reset-gpios to required, I observe the below warning. >>>>>>>>> >>>>>>>>> DTC_CHK Documentation/devicetree/bindings/usb/maxim,max33359.example.dtb >>>>>>>>> /home/alarm/linux-amlogic-5.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: >>>>>>>>> hub@1: 'reset-gpio' is a required property >>>>>>>>> from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# >>>>>>>> >>>>>>>> Where are the properties defined? If you open the binding you see: >>>>>>>> nowhere. You cannot define properties in some variant with "true". >>>>>>>> Please define all of them in top-level and only narrow/constrain when >>>>>>>> applicable. >>>>>>>> >>>>>>> What I meant is the example below, required meant applicable for both >>>>>>> the binding >>>>>>> But it shows me the above warning. >>>>>> >>>>>> My explanation stands... So again: >>>>>> >>>>>>>> Please define all of them in top-level and only narrow/constrain when >>>>>>>> applicable. >>>>>> >>>>> Apologies, But I have tried this multiple times but have not been able >>>>> to fix the device tree warning >>>> >>>> Did you document all properties in top-level "properties:" block? >>>> >>> Yes, I have, >>> >>> Can you suggest a couple of examples to follow? >>> I looked at some of the YAML files but could not fix my issue. >> >> 99% of bindings. Look also at example-schema. >> >> You can also attach here complete patch for fast look / short review. >> > > Please find the modified patch, I have tried a few things but none > resolve the binding warning. > I am not able to debug this. And where is the warning or the issue? Can you describe what problem do you have? > > -Thanks > Anand > -----8<----------8<----------8<----------8<----------8<----------8<----- > diff --git a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > index ee08b9c3721f..7f75fa3c1945 100644 > --- a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > +++ b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > @@ -9,9 +9,6 @@ title: Genesys Logic USB hub controller > maintainers: > - Icenowy Zheng <uwu@icenowy.me> > > -allOf: > - - $ref: usb-device.yaml# > - > properties: > compatible: > enum: > @@ -27,11 +24,47 @@ properties: > > vdd-supply: > description: > - the regulator that provides 3.3V core power to the hub. > + The regulator that provides 3.3V or 5.0V core power to the hub. > + > + peer-hub: > + $ref: /schemas/types.yaml#/definitions/phandle > + description: > + For onboard hub controllers that support USB 3.x and USB 2.0 hubs with > + shared resets and power supplies, this property is used to identify the > + hubs with which these are shared. > > required: > - compatible > - reg > + - vdd-supply > + - reset-gpios > + - peer-hub > + > +allOf: > + - $ref: usb-device.yaml# > + > + - if: > + properties: > + compatible: > + contains: > + enum: > + - usb5e3,608 > + then: > + properties: > + peer-hub: false > + vdd-supply: false > + > + - if: > + properties: > + compatible: > + contains: > + enum: > + - usb5e3,610 > + - usb5e3,620 > + then: > + properties: > + peer-hub: true > + vdd-supply: true Drop this if:, redundant. Best regards, Krzysztof _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub 2023-12-12 8:40 ` Krzysztof Kozlowski @ 2023-12-12 11:37 ` Anand Moon 2023-12-12 11:52 ` Krzysztof Kozlowski 0 siblings, 1 reply; 23+ messages in thread From: Anand Moon @ 2023-12-12 11:37 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Rob Herring, Greg Kroah-Hartman, Krzysztof Kozlowski, Conor Dooley, Icenowy Zheng, Neil Armstrong, linux-amlogic, Conor Dooley, linux-usb, devicetree, linux-kernel Hi Krzysztof, On Tue, 12 Dec 2023 at 14:10, Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote: > > On 12/12/2023 07:22, Anand Moon wrote: > > Hi Krzysztof, > > > > On Fri, 8 Dec 2023 at 17:47, Krzysztof Kozlowski > > <krzysztof.kozlowski@linaro.org> wrote: > >> > >> On 08/12/2023 12:19, Anand Moon wrote: > >>> Hi Krzysztof, > >>> > >>> On Fri, 8 Dec 2023 at 13:14, Krzysztof Kozlowski > >>> <krzysztof.kozlowski@linaro.org> wrote: > >>>> > >>>> On 08/12/2023 01:24, Anand Moon wrote: > >>>>>>>>> > >>>>>>>>> If I move reset-gpios to required, I observe the below warning. > >>>>>>>>> > >>>>>>>>> DTC_CHK Documentation/devicetree/bindings/usb/maxim,max33359.example.dtb > >>>>>>>>> /home/alarm/linux-amlogic-5.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: > >>>>>>>>> hub@1: 'reset-gpio' is a required property > >>>>>>>>> from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# > >>>>>>>> > >>>>>>>> Where are the properties defined? If you open the binding you see: > >>>>>>>> nowhere. You cannot define properties in some variant with "true". > >>>>>>>> Please define all of them in top-level and only narrow/constrain when > >>>>>>>> applicable. > >>>>>>>> > >>>>>>> What I meant is the example below, required meant applicable for both > >>>>>>> the binding > >>>>>>> But it shows me the above warning. > >>>>>> > >>>>>> My explanation stands... So again: > >>>>>> > >>>>>>>> Please define all of them in top-level and only narrow/constrain when > >>>>>>>> applicable. > >>>>>> > >>>>> Apologies, But I have tried this multiple times but have not been able > >>>>> to fix the device tree warning > >>>> > >>>> Did you document all properties in top-level "properties:" block? > >>>> > >>> Yes, I have, > >>> > >>> Can you suggest a couple of examples to follow? > >>> I looked at some of the YAML files but could not fix my issue. > >> > >> 99% of bindings. Look also at example-schema. > >> > >> You can also attach here complete patch for fast look / short review. > >> > > > > Please find the modified patch, I have tried a few things but none > > resolve the binding warning. > > I am not able to debug this. > > And where is the warning or the issue? Can you describe what problem do > you have? Here is the list of warnings I observed with this patch DTC_CHK Documentation/devicetree/bindings/usb/nvidia,tegra186-xusb.example.dtb /home/amoon/mainline/linux-amlogic-6.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: hub@1: 'vdd-supply' is a required property from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# /home/amoon/mainline/linux-amlogic-6.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: hub@1: 'reset-gpios' is a required property from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# /home/amoon/mainline/linux-amlogic-6.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: hub@1: 'peer-hub' is a required property from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# DTC_CHK Documentation/devicetree/bindings/usb/ti,tps6598x.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/xlnx,usb2.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/renesas,usb-xhci.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/renesas,usbhs.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/brcm,bcm7445-ehci.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/cypress,cypd4226.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/cdns,usb3.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/renesas,rzn1-usbf.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/nvidia,tegra124-xusb.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/ci-hdrc-usb2.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/brcm,usb-pinmap.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/renesas,usb3-peri.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/qcom,pmic-typec.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/microchip,usb5744.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/smsc,usb3503.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/mediatek,musb.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/vialab,vl817.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/marvell,pxau2o-ehci.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/richtek,rt1711h.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/usb.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/realtek,rts5411.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/nvidia,tegra210-xusb.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/realtek,rtd-dwc3.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/usb-drd.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/genesys,gl850g.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/ti,j721e-usb.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/ti,am62-usb.example.dtb /home/amoon/mainline/linux-amlogic-6.y-devel/Documentation/devicetree/bindings/usb/genesys,gl850g.example.dtb: hub@1: 'vdd-supply' is a required property from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# /home/amoon/mainline/linux-amlogic-6.y-devel/Documentation/devicetree/bindings/usb/genesys,gl850g.example.dtb: hub@1: 'peer-hub' is a required property from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# DTC_CHK Documentation/devicetree/bindings/usb/renesas,rzv2m-usb3drd.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/usb-hcd.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/fsl,imx8mq-dwc3.example.dtb DTC_CHK Documentation/devicetree/bindings/usb/mediatek,mtu3.example.dtb /home/amoon/mainline/linux-amlogic-6.y-devel/Documentation/devicetree/bindings/usb/usb-hcd.example.dtb: hub@1: 'vdd-supply' is a required property from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# /home/amoon/mainline/linux-amlogic-6.y-devel/Documentation/devicetree/bindings/usb/usb-hcd.example.dtb: hub@1: 'reset-gpios' is a required property from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# /home/amoon/mainline/linux-amlogic-6.y-devel/Documentation/devicetree/bindings/usb/usb-hcd.example.dtb: hub@1: 'peer-hub' is a required property from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# DTC_CHK Documentation/devicetree/bindings/usb/nxp,isp1760.example.dtb > > > > > -Thanks > > Anand > > -----8<----------8<----------8<----------8<----------8<----------8<----- > > diff --git a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > > b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > > index ee08b9c3721f..7f75fa3c1945 100644 > > --- a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > > +++ b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > > @@ -9,9 +9,6 @@ title: Genesys Logic USB hub controller > > maintainers: > > - Icenowy Zheng <uwu@icenowy.me> > > > > -allOf: > > - - $ref: usb-device.yaml# > > - > > properties: > > compatible: > > enum: > > @@ -27,11 +24,47 @@ properties: > > > > vdd-supply: > > description: > > - the regulator that provides 3.3V core power to the hub. > > + The regulator that provides 3.3V or 5.0V core power to the hub. > > + > > + peer-hub: > > + $ref: /schemas/types.yaml#/definitions/phandle > > + description: > > + For onboard hub controllers that support USB 3.x and USB 2.0 hubs with > > + shared resets and power supplies, this property is used to identify the > > + hubs with which these are shared. > > > > required: > > - compatible > > - reg > > + - vdd-supply > > + - reset-gpios > > + - peer-hub > > + > > +allOf: > > + - $ref: usb-device.yaml# > > + > > + - if: > > + properties: > > + compatible: > > + contains: > > + enum: > > + - usb5e3,608 > > + then: > > + properties: > > + peer-hub: false > > + vdd-supply: false > > + > > + - if: > > + properties: > > + compatible: > > + contains: > > + enum: > > + - usb5e3,610 > > + - usb5e3,620 > > + then: > > + properties: > > + peer-hub: true > > + vdd-supply: true > > Drop this if:, redundant. > No, this does not resolve the above issue. > Thanks -Anand _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub 2023-12-12 11:37 ` Anand Moon @ 2023-12-12 11:52 ` Krzysztof Kozlowski 2023-12-12 12:51 ` Anand Moon 0 siblings, 1 reply; 23+ messages in thread From: Krzysztof Kozlowski @ 2023-12-12 11:52 UTC (permalink / raw) To: Anand Moon Cc: Rob Herring, Greg Kroah-Hartman, Krzysztof Kozlowski, Conor Dooley, Icenowy Zheng, Neil Armstrong, linux-amlogic, Conor Dooley, linux-usb, devicetree, linux-kernel On 12/12/2023 12:37, Anand Moon wrote: > > Here is the list of warnings I observed with this patch > > DTC_CHK Documentation/devicetree/bindings/usb/nvidia,tegra186-xusb.example.dtb > /home/amoon/mainline/linux-amlogic-6.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: > hub@1: 'vdd-supply' is a required property You always require the property, but it is not valid for some devices. Just require it only where it is applicable (in if:then: clause). > from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# > /home/amoon/mainline/linux-amlogic-6.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: > hub@1: 'reset-gpios' is a required property > from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# > /home/amoon/mainline/linux-amlogic-6.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: > hub@1: 'peer-hub' is a required property ... >>> + - if: >>> + properties: >>> + compatible: >>> + contains: >>> + enum: >>> + - usb5e3,610 >>> + - usb5e3,620 >>> + then: >>> + properties: >>> + peer-hub: true >>> + vdd-supply: true >> >> Drop this if:, redundant. >> > No, this does not resolve the above issue. It shouldn't resolve it, not related. Best regards, Krzysztof _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub 2023-12-12 11:52 ` Krzysztof Kozlowski @ 2023-12-12 12:51 ` Anand Moon 2023-12-12 13:09 ` Krzysztof Kozlowski 0 siblings, 1 reply; 23+ messages in thread From: Anand Moon @ 2023-12-12 12:51 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Rob Herring, Greg Kroah-Hartman, Krzysztof Kozlowski, Conor Dooley, Icenowy Zheng, Neil Armstrong, linux-amlogic, Conor Dooley, linux-usb, devicetree, linux-kernel Hi Krzysztof, On Tue, 12 Dec 2023 at 17:22, Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote: > > On 12/12/2023 12:37, Anand Moon wrote: > > > > Here is the list of warnings I observed with this patch > > > > DTC_CHK Documentation/devicetree/bindings/usb/nvidia,tegra186-xusb.example.dtb > > /home/amoon/mainline/linux-amlogic-6.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: > > hub@1: 'vdd-supply' is a required property > > You always require the property, but it is not valid for some devices. > Just require it only where it is applicable (in if:then: clause). > I had already done this check many times before. my v6 original patch was doing the same and it passed all the tests but since I updated the required field it not parsing correctly. required: - compatible - reg - vdd-supply - reset-gpios - peer-hub > > > from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# > > /home/amoon/mainline/linux-amlogic-6.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: > > hub@1: 'reset-gpios' is a required property > > from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml# > > /home/amoon/mainline/linux-amlogic-6.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: > > hub@1: 'peer-hub' is a required property > > ... > > >>> + - if: > >>> + properties: > >>> + compatible: > >>> + contains: > >>> + enum: > >>> + - usb5e3,610 > >>> + - usb5e3,620 > >>> + then: > >>> + properties: > >>> + peer-hub: true > >>> + vdd-supply: true > >> > >> Drop this if:, redundant. > >> > > No, this does not resolve the above issue. > > It shouldn't resolve it, not related. > ok > > Best regards, > Krzysztof Thanks -Anand _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub 2023-12-12 12:51 ` Anand Moon @ 2023-12-12 13:09 ` Krzysztof Kozlowski 2023-12-12 13:17 ` Anand Moon 0 siblings, 1 reply; 23+ messages in thread From: Krzysztof Kozlowski @ 2023-12-12 13:09 UTC (permalink / raw) To: Anand Moon Cc: Rob Herring, Greg Kroah-Hartman, Krzysztof Kozlowski, Conor Dooley, Icenowy Zheng, Neil Armstrong, linux-amlogic, Conor Dooley, linux-usb, devicetree, linux-kernel On 12/12/2023 13:51, Anand Moon wrote: > Hi Krzysztof, > > On Tue, 12 Dec 2023 at 17:22, Krzysztof Kozlowski > <krzysztof.kozlowski@linaro.org> wrote: >> >> On 12/12/2023 12:37, Anand Moon wrote: >>> >>> Here is the list of warnings I observed with this patch >>> >>> DTC_CHK Documentation/devicetree/bindings/usb/nvidia,tegra186-xusb.example.dtb >>> /home/amoon/mainline/linux-amlogic-6.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: >>> hub@1: 'vdd-supply' is a required property >> >> You always require the property, but it is not valid for some devices. >> Just require it only where it is applicable (in if:then: clause). >> > I had already done this check many times before. I don't ask you to check. I ask you to change the code. > my v6 original patch was doing the same and it passed all the tests > but since I updated the required field it not parsing correctly. Your original v6 patch was different. I don't understand what you are trying to achieve. Or rather: how is it different, that my simple advice above does not work for you (as in the past you reply with some really unrelated sentence). Best regards, Krzysztof _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub 2023-12-12 13:09 ` Krzysztof Kozlowski @ 2023-12-12 13:17 ` Anand Moon 2024-04-04 4:27 ` Anand Moon 0 siblings, 1 reply; 23+ messages in thread From: Anand Moon @ 2023-12-12 13:17 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Rob Herring, Greg Kroah-Hartman, Krzysztof Kozlowski, Conor Dooley, Icenowy Zheng, Neil Armstrong, linux-amlogic, Conor Dooley, linux-usb, devicetree, linux-kernel Hi Krzysztof, On Tue, 12 Dec 2023 at 18:39, Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote: > > On 12/12/2023 13:51, Anand Moon wrote: > > Hi Krzysztof, > > > > On Tue, 12 Dec 2023 at 17:22, Krzysztof Kozlowski > > <krzysztof.kozlowski@linaro.org> wrote: > >> > >> On 12/12/2023 12:37, Anand Moon wrote: > >>> > >>> Here is the list of warnings I observed with this patch > >>> > >>> DTC_CHK Documentation/devicetree/bindings/usb/nvidia,tegra186-xusb.example.dtb > >>> /home/amoon/mainline/linux-amlogic-6.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: > >>> hub@1: 'vdd-supply' is a required property > >> > >> You always require the property, but it is not valid for some devices. > >> Just require it only where it is applicable (in if:then: clause). > >> > > I had already done this check many times before. > > I don't ask you to check. I ask you to change the code. > I have tried this and it's not working for me. > > my v6 original patch was doing the same and it passed all the tests > > but since I updated the required field it not parsing correctly. > > Your original v6 patch was different. I don't understand what you are > trying to achieve. Or rather: how is it different, that my simple advice > above does not work for you (as in the past you reply with some really > unrelated sentence). > Ok, It's my poor English grammar, thanks for your review comments. > Best regards, > Krzysztof > Thanks -Anand _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub 2023-12-12 13:17 ` Anand Moon @ 2024-04-04 4:27 ` Anand Moon 2024-04-04 6:12 ` Krzysztof Kozlowski 0 siblings, 1 reply; 23+ messages in thread From: Anand Moon @ 2024-04-04 4:27 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Rob Herring, Greg Kroah-Hartman, Krzysztof Kozlowski, Conor Dooley, Icenowy Zheng, Neil Armstrong, linux-amlogic, Conor Dooley, linux-usb, devicetree, linux-kernel Hi Krzysztof, On Tue, 12 Dec 2023 at 18:47, Anand Moon <linux.amoon@gmail.com> wrote: > > Hi Krzysztof, > > On Tue, 12 Dec 2023 at 18:39, Krzysztof Kozlowski > <krzysztof.kozlowski@linaro.org> wrote: > > > > On 12/12/2023 13:51, Anand Moon wrote: > > > Hi Krzysztof, > > > > > > On Tue, 12 Dec 2023 at 17:22, Krzysztof Kozlowski > > > <krzysztof.kozlowski@linaro.org> wrote: > > >> > > >> On 12/12/2023 12:37, Anand Moon wrote: > > >>> > > >>> Here is the list of warnings I observed with this patch > > >>> > > >>> DTC_CHK Documentation/devicetree/bindings/usb/nvidia,tegra186-xusb.example.dtb > > >>> /home/amoon/mainline/linux-amlogic-6.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: > > >>> hub@1: 'vdd-supply' is a required property > > >> > > >> You always require the property, but it is not valid for some devices. > > >> Just require it only where it is applicable (in if:then: clause). > > >> > > > I had already done this check many times before. > > > > I don't ask you to check. I ask you to change the code. > > > I have tried this and it's not working for me. > > > > my v6 original patch was doing the same and it passed all the tests > > > but since I updated the required field it not parsing correctly. > > > > Your original v6 patch was different. I don't understand what you are > > trying to achieve. Or rather: how is it different, that my simple advice > > above does not work for you (as in the past you reply with some really > > unrelated sentence). > > > Ok, It's my poor English grammar, thanks for your review comments. > > > Best regards, > > Krzysztof > > Any reason this device tree binding got removed,I cannot find this file Can not find the commit which removed this file. [0] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/usb?h=v6.9-rc2 Thanks -Anand _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub 2024-04-04 4:27 ` Anand Moon @ 2024-04-04 6:12 ` Krzysztof Kozlowski 2024-04-04 6:32 ` Anand Moon 0 siblings, 1 reply; 23+ messages in thread From: Krzysztof Kozlowski @ 2024-04-04 6:12 UTC (permalink / raw) To: Anand Moon Cc: Rob Herring, Greg Kroah-Hartman, Krzysztof Kozlowski, Conor Dooley, Icenowy Zheng, Neil Armstrong, linux-amlogic, Conor Dooley, linux-usb, devicetree, linux-kernel On 04/04/2024 06:27, Anand Moon wrote: > Hi Krzysztof, > > On Tue, 12 Dec 2023 at 18:47, Anand Moon <linux.amoon@gmail.com> wrote: >> >> Hi Krzysztof, >> >> On Tue, 12 Dec 2023 at 18:39, Krzysztof Kozlowski >> <krzysztof.kozlowski@linaro.org> wrote: >>> >>> On 12/12/2023 13:51, Anand Moon wrote: >>>> Hi Krzysztof, >>>> >>>> On Tue, 12 Dec 2023 at 17:22, Krzysztof Kozlowski >>>> <krzysztof.kozlowski@linaro.org> wrote: >>>>> >>>>> On 12/12/2023 12:37, Anand Moon wrote: >>>>>> >>>>>> Here is the list of warnings I observed with this patch >>>>>> >>>>>> DTC_CHK Documentation/devicetree/bindings/usb/nvidia,tegra186-xusb.example.dtb >>>>>> /home/amoon/mainline/linux-amlogic-6.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: >>>>>> hub@1: 'vdd-supply' is a required property >>>>> >>>>> You always require the property, but it is not valid for some devices. >>>>> Just require it only where it is applicable (in if:then: clause). >>>>> >>>> I had already done this check many times before. >>> >>> I don't ask you to check. I ask you to change the code. >>> >> I have tried this and it's not working for me. >> >>>> my v6 original patch was doing the same and it passed all the tests >>>> but since I updated the required field it not parsing correctly. >>> >>> Your original v6 patch was different. I don't understand what you are >>> trying to achieve. Or rather: how is it different, that my simple advice >>> above does not work for you (as in the past you reply with some really >>> unrelated sentence). >>> >> Ok, It's my poor English grammar, thanks for your review comments. >> >>> Best regards, >>> Krzysztof >>> > > Any reason this device tree binding got removed,I cannot find this file > Can not find the commit which removed this file. Use git log. Best regards, Krzysztof _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub 2024-04-04 6:12 ` Krzysztof Kozlowski @ 2024-04-04 6:32 ` Anand Moon 2024-04-04 6:34 ` Anand Moon 0 siblings, 1 reply; 23+ messages in thread From: Anand Moon @ 2024-04-04 6:32 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Rob Herring, Greg Kroah-Hartman, Krzysztof Kozlowski, Conor Dooley, Icenowy Zheng, Neil Armstrong, linux-amlogic, Conor Dooley, linux-usb, devicetree, linux-kernel Hi, On Thu, 4 Apr 2024 at 11:42, Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote: > > On 04/04/2024 06:27, Anand Moon wrote: > > Hi Krzysztof, > > > > On Tue, 12 Dec 2023 at 18:47, Anand Moon <linux.amoon@gmail.com> wrote: > >> > >> Hi Krzysztof, > >> > >> On Tue, 12 Dec 2023 at 18:39, Krzysztof Kozlowski > >> <krzysztof.kozlowski@linaro.org> wrote: > >>> > >>> On 12/12/2023 13:51, Anand Moon wrote: > >>>> Hi Krzysztof, > >>>> > >>>> On Tue, 12 Dec 2023 at 17:22, Krzysztof Kozlowski > >>>> <krzysztof.kozlowski@linaro.org> wrote: > >>>>> > >>>>> On 12/12/2023 12:37, Anand Moon wrote: > >>>>>> > >>>>>> Here is the list of warnings I observed with this patch > >>>>>> > >>>>>> DTC_CHK Documentation/devicetree/bindings/usb/nvidia,tegra186-xusb.example.dtb > >>>>>> /home/amoon/mainline/linux-amlogic-6.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: > >>>>>> hub@1: 'vdd-supply' is a required property > >>>>> > >>>>> You always require the property, but it is not valid for some devices. > >>>>> Just require it only where it is applicable (in if:then: clause). > >>>>> > >>>> I had already done this check many times before. > >>> > >>> I don't ask you to check. I ask you to change the code. > >>> > >> I have tried this and it's not working for me. > >> > >>>> my v6 original patch was doing the same and it passed all the tests > >>>> but since I updated the required field it not parsing correctly. > >>> > >>> Your original v6 patch was different. I don't understand what you are > >>> trying to achieve. Or rather: how is it different, that my simple advice > >>> above does not work for you (as in the past you reply with some really > >>> unrelated sentence). > >>> > >> Ok, It's my poor English grammar, thanks for your review comments. > >> > >>> Best regards, > >>> Krzysztof > >>> > > > > Any reason this device tree binding got removed,I cannot find this file > > Can not find the commit which removed this file. > > Use git log. > > Best regards, > Krzysztof > _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub 2024-04-04 6:32 ` Anand Moon @ 2024-04-04 6:34 ` Anand Moon 0 siblings, 0 replies; 23+ messages in thread From: Anand Moon @ 2024-04-04 6:34 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Rob Herring, Greg Kroah-Hartman, Krzysztof Kozlowski, Conor Dooley, Icenowy Zheng, Neil Armstrong, linux-amlogic, Conor Dooley, linux-usb, devicetree, linux-kernel Hi Krzysztof, On Thu, 4 Apr 2024 at 12:02, Anand Moon <linux.amoon@gmail.com> wrote: > > Hi, > > On Thu, 4 Apr 2024 at 11:42, Krzysztof Kozlowski > <krzysztof.kozlowski@linaro.org> wrote: > > > > On 04/04/2024 06:27, Anand Moon wrote: > > > Hi Krzysztof, > > > > > > On Tue, 12 Dec 2023 at 18:47, Anand Moon <linux.amoon@gmail.com> wrote: > > >> > > >> Hi Krzysztof, > > >> > > >> On Tue, 12 Dec 2023 at 18:39, Krzysztof Kozlowski > > >> <krzysztof.kozlowski@linaro.org> wrote: > > >>> > > >>> On 12/12/2023 13:51, Anand Moon wrote: > > >>>> Hi Krzysztof, > > >>>> > > >>>> On Tue, 12 Dec 2023 at 17:22, Krzysztof Kozlowski > > >>>> <krzysztof.kozlowski@linaro.org> wrote: > > >>>>> > > >>>>> On 12/12/2023 12:37, Anand Moon wrote: > > >>>>>> > > >>>>>> Here is the list of warnings I observed with this patch > > >>>>>> > > >>>>>> DTC_CHK Documentation/devicetree/bindings/usb/nvidia,tegra186-xusb.example.dtb > > >>>>>> /home/amoon/mainline/linux-amlogic-6.y-devel/Documentation/devicetree/bindings/usb/usb-device.example.dtb: > > >>>>>> hub@1: 'vdd-supply' is a required property > > >>>>> > > >>>>> You always require the property, but it is not valid for some devices. > > >>>>> Just require it only where it is applicable (in if:then: clause). > > >>>>> > > >>>> I had already done this check many times before. > > >>> > > >>> I don't ask you to check. I ask you to change the code. > > >>> > > >> I have tried this and it's not working for me. > > >> > > >>>> my v6 original patch was doing the same and it passed all the tests > > >>>> but since I updated the required field it not parsing correctly. > > >>> > > >>> Your original v6 patch was different. I don't understand what you are > > >>> trying to achieve. Or rather: how is it different, that my simple advice > > >>> above does not work for you (as in the past you reply with some really > > >>> unrelated sentence). > > >>> > > >> Ok, It's my poor English grammar, thanks for your review comments. > > >> > > >>> Best regards, > > >>> Krzysztof > > >>> > > > > > > Any reason this device tree binding got removed,I cannot find this file > > > Can not find the commit which removed this file. > > > > Use git log. > > I got confused with the file name and my local changes. > > Best regards, > > Krzysztof > > Thanks -Anand _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH v6 2/2] arm64: dts: amlogic: Used onboard usb hub reset on odroid n2 2023-12-04 14:44 [PATCH v6 0/2] Use onboard usb hub reset on Odroid N2 Anand Moon 2023-12-04 14:44 ` [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub Anand Moon @ 2023-12-04 14:44 ` Anand Moon 1 sibling, 0 replies; 23+ messages in thread From: Anand Moon @ 2023-12-04 14:44 UTC (permalink / raw) To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Neil Armstrong, Kevin Hilman, Jerome Brunet, Martin Blumenstingl Cc: Anand Moon, linux-amlogic, devicetree, linux-arm-kernel, linux-kernel On Odroid n2/n2+ previously use gpio-hog to reset the usb hub, switch to used on-board usb hub reset to enable the usb hub and enable power to hub. Signed-off-by: Anand Moon <linux.amoon@gmail.com> --- V6:none V5:none V4:none V3:none V2:none V1:none --- .../dts/amlogic/meson-g12b-odroid-n2.dtsi | 36 ++++++++++++------- 1 file changed, 24 insertions(+), 12 deletions(-) diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi index 91c9769fda20..9e671444eca6 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi @@ -31,6 +31,30 @@ hub_5v: regulator-hub_5v { enable-active-high; }; + /* USB hub supports both USB 2.0 and USB 3.0 root hub */ + usb-hub { + dr_mode = "host"; + #address-cells = <1>; + #size-cells = <0>; + + /* 2.0 hub on port 1 */ + hub_2_0: hub@1 { + compatible = "usb5e3,610"; + reg = <1>; + peer-hub = <&hub_3_0>; + vdd-supply = <&usb_pwr_en>; + }; + + /* 3.0 hub on port 4 */ + hub_3_0: hub@2 { + compatible = "usb5e3,620"; + reg = <2>; + peer-hub = <&hub_2_0>; + reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>; + vdd-supply = <&vcc_5v>; + }; + }; + sound { compatible = "amlogic,axg-sound-card"; model = "ODROID-N2"; @@ -234,18 +258,6 @@ &gpio { "PIN_3", /* GPIOX_17 */ "PIN_5", /* GPIOX_18 */ "PIN_36"; /* GPIOX_19 */ - /* - * WARNING: The USB Hub on the Odroid-N2 needs a reset signal - * to be turned high in order to be detected by the USB Controller - * This signal should be handled by a USB specific power sequence - * in order to reset the Hub when USB bus is powered down. - */ - usb-hub-hog { - gpio-hog; - gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>; - output-high; - line-name = "usb-hub-reset"; - }; }; &i2c3 { -- 2.42.0 _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply related [flat|nested] 23+ messages in thread
end of thread, other threads:[~2024-04-04 6:34 UTC | newest] Thread overview: 23+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2023-12-04 14:44 [PATCH v6 0/2] Use onboard usb hub reset on Odroid N2 Anand Moon 2023-12-04 14:44 ` [PATCH v6 1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub Anand Moon 2023-12-06 13:53 ` Rob Herring 2023-12-06 17:14 ` Anand Moon 2023-12-07 8:30 ` Krzysztof Kozlowski 2023-12-07 12:33 ` Anand Moon 2023-12-07 12:40 ` Krzysztof Kozlowski 2023-12-08 0:24 ` Anand Moon 2023-12-08 7:44 ` Krzysztof Kozlowski 2023-12-08 11:19 ` Anand Moon 2023-12-08 12:17 ` Krzysztof Kozlowski 2023-12-12 6:22 ` Anand Moon 2023-12-12 8:40 ` Krzysztof Kozlowski 2023-12-12 11:37 ` Anand Moon 2023-12-12 11:52 ` Krzysztof Kozlowski 2023-12-12 12:51 ` Anand Moon 2023-12-12 13:09 ` Krzysztof Kozlowski 2023-12-12 13:17 ` Anand Moon 2024-04-04 4:27 ` Anand Moon 2024-04-04 6:12 ` Krzysztof Kozlowski 2024-04-04 6:32 ` Anand Moon 2024-04-04 6:34 ` Anand Moon 2023-12-04 14:44 ` [PATCH v6 2/2] arm64: dts: amlogic: Used onboard usb hub reset on odroid n2 Anand Moon
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).